CAMBRIONIX TS2-16 User manual


UserManual
TS2-16









2022-09
© 2022 Cambrionix Ltd. All rights reserved.
EN

TS2-16 Page 1 of 36
1.TableofContents
1. Table of Contents 1
2. Your TS2-16 at a glance 3
2.1.KeyFeatures 3
3. Safety 4
3.1.Signalwordpanel 4
3.2.Safetyalertsymbol 5
3.3.Pictograms 5
3.4.Productmodification 5
3.5.Powersupply 6
3.6.StorageandInstallation 7
4. Getting Started 8
4.1.Openingyourproduct 8
4.2.What'sIncluded 8
4.3.Connectingtothemains 9
4.4.Charging 9
4.5.Cables 9
4.6.Registration 9
4.7.HelpandSupport 9
5. Using your TS2-16 11
5.0.1LEDConfiguration 11
5.1.Usingwithoutconnectingtohost 11
5.2.Usingwhenconnectedtohost 12
5.2.1ConnectingtheHubtoahostcomputer 12
5.2.2Charging 12
5.2.3DataTransfer 12
5.3.Scalability 14
5.4.ManagePorts&YourTS2-16 15
5.4.1PortModes 15
5.4.2Switchingportmodes 15
5.4.3ChargingProfiles 16
5.4.4Firmware 16
5.5.Software 18
5.5.1InstallingSoftware 18
5.5.2LiveViewer 19
5.5.3CambrionixAPI 20

TS2-16 Page 2 of 36
5.5.4UpdatingSoftware 20
5.5.5RemovingSoftware 21
5.5.6CommandLineInstructions(CLI) 22
5.6.CleaningyourTS2-16 24
6. Product Specifications 25
6.1.InputPowerRequirements 25
6.2.Errorflagrailvalues 25
6.3.ConsumablesandPlacingOrders 25
7. Troubleshooting 27
7.1.Initialtroubleshootingtips 27
7.2.LoggingthroughLiveViewer 27
7.3.HardwareFailure 28
7.4.Deviceconnection. 28
7.5.Hubconnectionissues 29
7.6.NoGUI 30
7.7.Softwaretroubleshooting 31
8. Disposal 32
9. Returns and Damaged Products 33
9.1.WhatdoIdoifmyorderarrivesandsomethingtheproductisfaulty
orisphysicallydamaged? 33
9.2.WhathappensafterIhaverequestedaReturn? 33

TS2-16 Page 3 of 36
2.YourTS2-16ataglance


TheTS2-16hasbeendesignedtoprovidehigh-speeddatatransfertoUSBcompliantdevices
withoutbeingconstrainedbyendpointlimits.

TheTS2-16canchargeattachedUSBdeviceswithoutusingalocalcomputer.TheTS2-16allows
almostanydevicetobechargedatitsoptimumrate(upto2.4A).Thefirmwarecanbeupdated
toensuretheTS2-16canchargethelatestdevices.Itisreadytochargeout-of-the-boxandsync
deviceswhenattachedtoahostcomputer.

Whenalocal(host)computerisattached,thehostcancontroltheoperationofeachportusing
softwareprovidedbyCambrionix.Devicechargingandsynchronisationcanbe
monitoredthroughCambrionix’sLiveViewerApplication,theApplicationProgramming
Interface(API)orCommandLineInterface(CLI).Cambrionix’sfreemonitoringandcontrol
softwarecanbedownloadedfromwww.cambrionix.com/products/api

WithyourTS2-16thereisaThunderbolt™connectiontothehostwhich,iscapableofupto
20Gbps,meaningyourupstreamspeedstothehostwillbecapableofthisdatatransferrate.
Theupstreamdatatransferratewillbesharedamongstthedownstream16xUSB2.0Type-A
connections.


2.1.KeyFeatures

Up To
480Mbps
per Port
Up To
2.4A
per Port
Up To
96
Devices
TransferDataSeamlessly Power Scalability
Eachhigh-speedportcan
transferdataupto480Mbps
Eachportcanchargedevicesup
to2.4A(12W)
Upto96devicescanbecon-
nectedatonceusingmultiple
hubs

TS2-16 Page 4 of 36
3.Safety

Thisusermanualisforinformationalpurposesonly,itcontainsinformationforthestart-upand
operationofthisproduct.Note:thecontentsandtheproductdescribedaresubjecttochange
withoutnotice.Toavoidinjuriesanddamage,observethesafetyinstructionsintheuser
manual.

ThismanualhasbeenarrangedtofollowIEC/ICEE82079-1standard.Thisistofacilitatethe
easierunderstandingandlocationofinformationrelatingtotheTS2-16.Anyerrorsor
omissionscanbereportedusingoursupportticketsystem(seeHelpandSupport).Thisway,any
issuescanbecollectedandfixed.

Understandingandobservingtheinstructionsinthisusermanualareprerequisitesfor
hazard-freeuseandsafetyduringoperation.Thisusermanualcannotcoverallpossible
applications.Ifyouwouldlikeadditionalinformationorifproblemsarisethatarenot
sufficientlyaddressedinthismanual,pleaseaskyourdistributororcontactusdirectlyusingthe
meanspreferred,whicharelocatedonthebackcoverofthismanual.

CAUTION
Personal Injury and Damage to the product
lObservethesafetyinstructionsinthisusermanual

3.1.Signalwordpanel

Dependingontheprobabilityofseriousconsequences,potentialdangersareidentifiedwitha
signalword,thecorrespondingsafetycolour,andifappropriate,thesafetyalertsymbol.


CAUTION
Indicatesapotentiallyhazardoussituationthat,ifnotavoided,mayresultinmoderateor
minor(reversible)injury.


CAUTION
Indicatesapotentiallyhazardoussituationwhich,ifnotavoided,mayresultindamagetothe
productanditsfunctions,ortopropertyinitsproximity.

TS2-16 Page 5 of 36



3.2.Safetyalertsymbol

Useofthesafetyalertsymbolindicatesariskofinjury.

Observeallmeasuresthataremarkedwiththesafetyalertsymbolinorderto
avoidinjury


3.3.Pictograms

Warning Signs
Electricalhazard FireHazard
Mandatory action signs
Readoperatinginstructions Mandatoryregulation


3.4.Productmodification

CambrionixproductsaredesignedandmanufacturedtomeettherequirementsofUKand
Internationalsafetyregulations.Modificationstotheproductcouldaffectsafetyandrenderthe
productnon-compliantwithrelevantsafetystandards,resultingininjuryordamagetothe
product.


CAUTION
An electric shock or personal injury may occur


TS2-16 Page 6 of 36
CAUTION
lDonotmodifytheproductinanyway.
lDonotdismantletheproduct.


CAUTION
Fire, or personal injury may occur

lDonotobstructairventsontheproduct.
lDonotcovertheproductincombustiblematerial.


CAUTION
Damage to your product may occur

lDonotbendorcompressanypartoftheproduct.



3.5.Powersupply

Thissectiondescribesthesafetyprecautionsyoumustfollowwhenusingthepowersupply.


CAUTION
An electric shock or personal injury may occur

lDonotuseadamagedpowercordorplug,oraloosepowersocket.
lDonottouchthepowerplugwithwethands.
lDonotallowliquidstocomeintocontactwiththeunitorpowersupply.


CAUTION
Damage to your product may occur
lDonotshortcircuitthePowerSupplyUnit(PSU)suppliedwithyour
product.
lDonotdisconnectthepowercordwhiletheproductisbeingused.

TS2-16 Page 7 of 36
CAUTION
lDonotbendorpullthepowercordwithexcessiveforce.
lDonotuseapowersupplythatexceedsthepowersupplyspecifications
withinthismanual



3.6.StorageandInstallation

ThissectiondescribessafetyprecautionsyoumustfollowwheninstallingandstoringyourTS2-
16.


CAUTION
An electric shock or personal injury may occur

lDonotplacethepowercordnearheatsources.
lConnecttheplugtoanearthedsocket.


CAUTION
Damage to your Cambrionix product may occur

lOperatetheproductonlyinanenvironmentwheretheambient
temperatureisinsidetheoperatingtemperaturerange.
lOperatetheproductonlyinanenvironmentwheretherelativehumidityis
insidetheoperatingrange.
lBecarefulnottoleavethepowercordunderneathaheavyobject.


CAUTION
Overheated power sockets may cause a fire

lDonotoverloadthepowersocketthatyourhubisconnectedto.
lInsertthepowerplugallthewayintothesocketsothatitisnotloose.


TS2-16 Page 8 of 36
4.GettingStarted

Thismanualprovidesareferenceforend-usersinstallingforthefirsttimeandusingtheirhub
afterthat.Aswellasaguideforproductsafety-relatedinformation.

TheTS2-16isintendedtobeusedinanindoorstaticenvironmentinwhichtheenvironment
fallswithinthetestedspecificationstoprovidecharge,syncandmanagementfunctionality.
Pleaseseethephysicalspecificationssectionofthismanualforinformationonthe
environmentspecifications.

4.1.Openingyourproduct
Whenyouhavereceivedyourproduct,pleasecheckthepackingsliptoensureallcontentsand
quantitiesarecorrectbeforeopening.Thisistoavoidretestingandrepackaginganyitemsthat
arenotrequired.

Whenopeningthepackaging,useasuitablemethodtoopentheboxi.e,donotuseaknife.
Thisistoensuretheproductisnotdamaged.

CAUTION
Personal Injury and Damage to the product
lTherewillbeastickeronthehubadvisingyoutoreadtheUsermanualbeforeuse.This
willneedtoberemovedbeforeuseasitmaybecoveringhostports,ventsetc.

4.2.What'sIncluded
lThunderbolt™2Cable(toprovidecommunicationbetweenthehostsystemandhub)
lTS2-16Hub
l2mMainspowercable(CountryspecifiedonorderincludingfusefortheUKplugs)

Part description Part number

UKPowercable 200144
USPowercable 200327
EUPowercable 200329
AUSPowercable 200337
INDPowercable 200341

TS2-16 Page 9 of 36

4.3.Connectingtothemains
PeriodicinspectionsshouldbemadetopowersupplycablesandanyUSBcablesforanysignsof
damage.Ifanydamageisfound,replacethedamagedcordbeforefurtheruse.

PleasenotethatUSBspecificationsrequireaminimum100mAchargecurrenttobedelivered
duringdatatransfer.Asindicatedinabove,iftheattacheddevicehasaBC1.2compliantCDP
port,thedevicecandrawupto2.4Awhiletransferringdata.

4.4.Charging
YourTS2-16willallowyourdevicetochargeatthemaximumratepossibleupto2.4A.Theway
thatchargingtakesplaceistheTS2-16willprovidethedevicewithacapabilitytochargeand
thedevicesUSBchargingcontrollerwilldeterminethemaximumamountofchargeitwantsto
drawdown.

4.5.Cables
SomeUSBcablesaredatatransferonly,andsomearepowerdeliveryonly.Therearealso
optionsthatcanhandlebothtasks.Besuretoverifyacable’sabilitiesbeforepurchasingitand
selectacablewhichcanhandlethespeedsandpowertransferthatyourequire.Wewould
adviceusingthecablethatwasprovidedwiththedevicetoconnecttoourhubs.

4.6.Registration
Youmayregisteryourproductatwww.cambrionix.com/product-registration

4.7.HelpandSupport
FAQsandhelpcanbefoundontheHelppagehere
lwww.cambrionix.com/help_pages/help.
Youcanraiseasupportticketformoreindepthsupporthere
lhttps://cambrionix.atlassian.net/servicedesk/customer/portals
Youcanalsodownloadanyofourmanualsandkeepuptodateatthelinkhere
lwww.cambrionix.com/product-user-manuals


TS2-16 Page 10 of 36
Whencontactingsupport,pleasesupplytheproductinformationforthehubinquestion.This
canbefoundontheDeviceInformationPlatewhichiseitherontheundersideorbackofthe
unit.

ProvidingserialandPurchaseordernumbers,canhelpidentifytheproductinquestionfaster,
andspeeduptheprocess.

TS2-16 Page 11 of 36
5.UsingyourTS2-16

Inthissection,youcanfindinformationusingyourhubinchargeorsyncapplication.Youcan
alsofindinformationonmanagingyourhub,changingportmodes,connectingmultiplehubsto
onehostandusingCambrionixSoftware.

5.0.1LEDConfiguration

YourTS2-16hasinbuiltLEDsusedtoshowthestateoftheportsordevices.TheseLEDscanbe
configuredtosupportyourusecase;thiscanbecontrolledeitherbyusingtheAPItosend
commandsdirectlyorthroughseparatesoftware.

ThedefaultLEDbehaviourofthehubisbelow.

Colour Behaviour
FlashingRed Portisinchargemodeandisprofilingthedevice
Red Portisinchargemodeandischarging
Yellow Portisinsyncmodeandhasahostconnection
Green Portisinchargemodeandthedevicehasreachedthe
chargedthreshold

5.1.Usingwithoutconnectingtohost

WhentheHubisswitchedonandisnotconnectedtoalocalhostcomputeritis
automaticallyconfiguredtochargedevicesusingitsintelligentchargingalgorithm.Connectthe
devicestobechargedtoanyoftheavailableports(nottheHostPort)using
USB-compliantcables.

Oncethedevicesareconnected,thealgorithmwilldetectthehighestchargerateallowablefor
eachattacheddevice.Chargingattheoptimumrate(upto2.4A)specifiedbythemanufacturer
willcommenceonceprofilingiscomplete.Dependingonthestateofchargeofthedevice
attached,thismaytaketensofseconds.




TS2-16 Page 12 of 36
5.2.Usingwhenconnectedtohost

5.2.1ConnectingtheHubtoahostcomputer
YoucanuseeitherThunderbolt™hostportontherearofthehubtoconnecttoyourhost
system;therearetwoportsontherear,soyoucanuseoneporttoconnectthehostandthe
otherporttodaisychainmultiplehubs.

5.2.2Charging
WhentheHostPortisconnectedtoalocalcomputer,thehubdefaultstoSyncmodeand
chargecurrentsaredeterminedaccordingtoUSBImplementersForum(USBIF)Super-Speed
USB3specifications.IftheattacheddevicecomplieswithUSB-IFBatteryCharging
specificationBC1.2andsupportsChargingDownstreamPort(CDP),thehubcanprovide
high-speedchargingat2.4A.IftheconnecteddevicedoesnotcomplywithBC1.2,thecharge
currentwillbelimitedto500mAincompliancewithUSBspecifications.

Ifyouwishtolimitthechargingtoyourdeviceswhilstconnectedtoyourhostsystemthenyou
candisableCDPonallportsbyinputtingthefollowingcommands.

TheCLIcommandsforturningoffthesyncchargeoptions,witha1or0perport.
settings_unlock settings_reset settings_set sync_chrg 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 settings_set alt_sync_chrg 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
reboot

ThiscanalsobedoneviatheAPIifthisiseasier.Justsupplythatstring(joinedwith\n)like:

cbrxapi.cbrx_connection_set(handle, "settings",
"settings_unlock\nsettings_reset\nsettings_set sync_chrg 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0\nsettings_set alt_sync_chrg 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0 0\nreboot")

Notethatsettings_resetclearsanyprevioussettings,soifyouneedtoretainsomethingelse,it
wouldbebettertoissuesettings_displayfirst,whichgivesyoutheentiresettingswhichyou
canthenmodifyandre-issueinentirity.

5.2.3DataTransfer
Ifyouwishtotransferdata,changeapplications,restoreorupdateyourmobiledevice,adata

TS2-16 Page 13 of 36
connectiontoalocalhostcomputerisrequired.ThehubiscompatiblewithmacOS®,
Windows™andLinux®operatingsystemsandcantransferdatabetweentheseoperating
systemsandmanymobileoperatingsystemssuchasiOS™andAndroid™.

Inordertotransferdata,connectthehostporttoyourlocal(host)computerusinga
Thunderbolt™2compliantcable.Anydevicesconnectedtothehubwillnowappearasifthey
wereconnectedtothehostcomputer’sUSBport.




TS2-16 Page 14 of 36
5.3.Scalability

USBcontrollersgenerallyhaveanendpointlimit,limitingthenumberofdevicesthatcanbe
enumeratedwhenconnectedtotheUSB3portofalocalcomputer.USB3portxHCIhost
controllersinmostcomputerslimitthenumberofendpointsenumeratedbetween64and128.
Mobiledevicesenumerateasmorethanoneendpoint,andcomplexdeviceswithtouchpanels
oftenenumerateas5or6endpoints.Consequently,thenumberofdevicesthatcanbe
successfullyenumeratedistypicallylimitedtolessthantwenty.

ByusingThunderbolt™connectivityandincorporatinghostcontrollersinsidethehubeachport
canhandleupto16endpoints.Ifyouwishtosynchronisemoredevices,multiplehubscanbe
daisy-chainedtoallowupto96devicestobemanagedsimultaneouslyfromasinglehost
computer.

Todaisy-chainmultiplehubs,eachhubneedstobeconnectedtomainspowerindividually,
thenthefirsthubinthechainshouldbeconnectedtothelocalcomputerthroughoneofthe
Thunderbolt™ports.Thenexthubinthedaisy-chainisconnectedusingoneofits
Thunderbolt™portstotheremainingThunderbolt™portofthefirsthub.Athird,fourthand
fifthhubcanbeaddedinthesameway,connectingtheavailableThunderbolt™portofthe
previoushubtooneoftheThunderbolt™portsofthenextdeviceinthedaisy-chain.Usingthis
approach,amaximumofsixhubscanbelinkedtogether,allowing96devicestobesyncedfrom
asinglehostcomputer.



TS2-16 Page 15 of 36
5.4.ManagePorts&YourTS2-16

EachportonyourTS2-16canbemanagedeitherindividually,oralltogether.Youcanturnthe
portsoffandon,changetheportmode,orchangethechargingprofiles.Thiscanbedone
eitherthroughLiveViewer,orbyconnectingtothehubviatheAPI.

5.4.1PortModes

Charge Turnspecificportsorthewholehubtochargeonlymode(nodata
connection,hubemulatesanOEMcharger)
Sync Turnspecificportsorthewholehubtosyncmode
Off Turnspecificportsonorofforswitchthewholehubonoroff(no
powerandnodatachannelsopen,mimicsunpluggingthedevice)

5.4.2Switchingportmodes
YoucanswitchbetweenportmodesbyusingourLiveViewerapplicationorbyusingtheCLI.If
youswitchaportoffthenthiswillstopanyconnectiontakingplacetotheUSBdeviceand
wouldmimicunpluggingtheUSBdevicecompletelyfromthehostsystem.

IfyouareinSyncmodeandthenswitchtoChargemodetheUSBdevicewilldisconnectbriefly
whilsttheprofilingprocesstakesplace.Oncetheprofilinghastakenplace,andacharging
profileisselected,thedevicewillthendrawachargerate,whichwillbedefinedbythe
chargingcontrollerwithintheUSBdevice.Thechargingprofilewilllimitthemaximumamount
thatthedeviceisabletodraw.

IfyouareinOfforChargemodeandswitchtoSyncmodetheUSBdevicewilldisconnectbriefly
whilstadataconnectionisopened,theUSBdevicewillthenbecomeavailabletothehostasif
theUSBdeviceisconnecteddirectlytothehost,andwillbeabletosyncdataatamaximum
rateof480Mbps.TheTS2-16willalsochargethedevicewhilstconnected.Itisimpossibleto
haveadataconnectiontoaUSBdevicewithoutanypowernegotiating,youcanreducethe
chargingratesavailablebydisablingCDP(Chargingdownstreamport).

YoucandisableCDPthroughNVRAMsettingseitherbygoingthroughthehubsettingsand
turning"Synccharge"offorthroughtheAPIanddisablingitviacode.Forexample,usingthe
commandline,theinstructionswouldbeasbelow.


TS2-16 Page 16 of 36
settings_unlock settings_set sync_chrg
0000000000000000

5.4.3ChargingProfiles
Toensureattacheddeviceschargeattheiroptimumrate,oursmartUSBhubscomewiththe
belowintelligentchargingprofilesbuiltin:

0 Intelligentchargingalgorithmwhichwillselectaprofile1-6
1 2.1A(Apple)
2BC1.2Standard(thiscoversthemajorityofAndroid™phonesand
otherdevices)
3 Samsung
4 2.1A(Profile1butwithalongertimeout)
5 1.0A(TypicallyusedbyApple)
6 2.4A(TypicallyusedbyApple)
5.4.4Firmware
ThefirmwarecanbekeptuptodateusingourLiveViewersoftware.Aspartofdeliveringan
easyuserexperience,ourLiveViewerapplicationisnowaset-and-forgetsolution.The
LiveViewerapplicationwilldiscoveryourUSBhub’sfirmwareandpresentanupdateforyou.

Toupdatethefirmware,first,gotothefirmwareupdatersectionofLiveViewer.Hereyoucan
seetheavailableFirmwareversionstodownloadandinstalltothehub.

Thecurrentfirmwareversiononthehubisdisplayedinthefirmwareupdatersectionalongside
thehub'sname.Thiswillappearredifanewerversionisavailableorgreenifitisthemostup
todate.


TS2-16 Page 17 of 36

Toinstallthefirmwareontothehubclickthehub/hubsconnectedthatyouwanttoupdate,
thenselectthefirmwareversionyouwanttoupgradeto.Onceselectedpresstheupdate
buttonatthetopandtheupdatewillcommence.

Firmwareversionsandhardware
Weadvisenottochangethefirmwareversiononanynewproductsyoureceiveasthismay
causecompatibilityissuesandstopyourTS2-16fromfunctioning.

CAUTION
Your TS2-16 may not function correctly

lDonotinstalloldfirmwareontoanewproduct



CAUTION
Your Cambrionix Firmware may get corrupted

lDonotinterrupttheFirmwareupdateprocess.
lDonotdisconnectthepowerduringtheupdateprocess.

TS2-16 Page 18 of 36
5.5.Software

Moreproductivity,savingyoutime.CambrionixprovidesthreeinterfacesbywhichtheHubcan
bemonitoredandmanaged:

•LiveViewer
•CambrionixAPI
•CommandLineInstructions

TheTS2-16usesstringcommandstocommunicatewiththehostsystem.Thesecanbesentvia
thevirtualserialportoftheTS2-16directly,ortheAPIcanbeusedtoprovideotherprotocols
thatsendtranslatedstringcommands.LiveViewercanusetheAPItointeractwiththedevices
throughauser-friendlyapplication.

TherearethreedifferentchannelsforbothourLiveViewerapplicationandtheAPI.Thethree
channelsareAlpha/BetaandRelease.Wewouldrecommendusingthereleaseversionofboth
theAPIandLiveViewer.

WewillpushbugfixesandupdatesthroughAlphaandthenontoBetabeforeitismergedinto
theReleaseversion.Ifyouhavefoundabugthatwehaveafixfor,theAlphaandBetareleases
mayalreadyhaveaddressedtheseandimplementedfixes.

5.5.1InstallingSoftware

Cambrionixhastwopiecesofsoftwarethatcanbeusedtomanagethedevicesandyourhub
usingdifferenthostsystems.Thissectionhasinstructionsandinformationonusingour
softwareonthreeofthemostpopularhostsystems.

Oursoftwareisavailabletodownloadfromwww.cambrionix.com/software,youwillfind
softwareavailableforWindows™,Mac®andLinux®Systems.

Linux®OSsystemstestedwithoursoftwareareUbuntu18.04LTSorDebian9;someotherOS
versionsbasedonthetwomentionedwillwork.SomedifferentLinux®OSversionsmaywork,
butwehavenottestedwiththem.

ToinstallonMac®andWindows™systems,downloadtheinstallfilesfromtheabovelink,once
downloadedruntheinstallprocessanddialogueboxeswillhelpyouthroughinstallationand
initialset-up.


TS2-16 Page 19 of 36
ForLinux®systems,downloadtheinstallfilesfromthewebsiteattheabovelink.Once
downloaded,youcaneitherinstallitfromthedesktopGUIorthecommandlinevia:

sudo apt install ./

afterthiscommandyouwillneedtoenterthefilenamethathasjustbeendownloadedfrom
ourwebsite.

5.5.2LiveViewer
LiveViewerisanapplicationdownloadedfromwww.cambrionix.com/products/liveviewer.
Oncedownloadedandinstalledonthehostcomputer,LiveViewerallowsyoutoswitchthe
portsonandoffandsettheportmode.LiveViewer’shomepageshowsthefollowing
informationaboutalltheports:

•Status(Attached/disconnected)
•Mode(Charge/Sync/Off)
•Profile(Chargingprofile)
•Duration(Howlongthedevicehasbeenattached)
•Endtime(Timethebatteryreachesathreshold(full)level)
•Current(QuickchargecurrentinmA)
•Energy(Presentenergyrate)

Tickboxesadjacenttoeachportsymbolallowthatportmodetobechangedwhenthe"enable
portcontrols"isselected.WhentheportisinSyncmode,onlyinstantaneouscurrentcanbe
monitoredthroughLiveViewer.WhentheportisinChargemode,thechargeprofile,current,
energyrate,chargedurationandendtimearedisplayed.Inadditiontoindividualport
informationandcontrol,LiveViewershowsthehubrailvoltages,timesinceswitchedon,total
currentandpower,andtemperature.FurtherdetailsonLiveViewerareavailableonour
website.
NVRAMsettings
Withinyourhub,therearesomespecificcontrollablesettingscalled"non-volatile
RAMsettings",whicharereferredtoasNVRAMsettings.Thesecontrolavarietyofdifferent
settingsonyourTS2-16.

YoucannavigatetotheNVRAMsettingsbyopeningLiveViewerandselectingthehubyouwant
toconnectto.Onceyouhavechosentheconnectedhub,navigatetothebelowicononthetop
rightofthescreenfromLiveViewerandthenclickingadvancedonthebottomofthepage