CAME ATS-P3 KIT User manual

CAME.COM/UK
ATS-P3 kit
QUICK SETUP GUIDE
Typical gate setup & geometry
Gate motor manual release
Kit wiring diagram
Control panel guide & safety
Complete kit for a pair of swing gates weighing
up to 400kg per leaf / max. width 3m
TO BE READ IN CONJUNCTION WITH THE FULL INSTRUCTION MANUAL

CONTENTS
DIR10
Pair of Photocells
AF43S
Radio Frequency Card
top-a433n
Tuned Antenna
ZA3P
Control Panel
TOPD4FKS
Fixed code Transmitter
ATS30AGS
Motor
x2
ATS-P3: KIT CONTENTS
x2
1Kit Contents
2Safety Instructions
3Typical Gate Setup
4Geometry
5Manual Release Instructions
6Kit Wiring Diagram
7Control Panel:
Quick Start Guide
8Control Panel:
Programming Transmitters
9Connect Setup
10 Control Panel: Safety
11 Optional Accessories

SAFETY INSTRUCTIONS
When correctly installed in compliance to installation instructions and adhering to all
current electrical, mechanical and manufacturer regulations, your automation system
will provide a high degree of safety and problem free operation.
Please take note of the following warnings that must be followed in order to
prevent accidents during your gate operation:
• Do not allow children to play near the gate.
• Keep all remote control operating devices out of the reach of children.
• Do not pass through the gate whilst in operation. Wait until they are fully open before passing through.
• Do not stop unnecessarily when passing through the gate.
• Keep feet away from the bottom of the gate during operation.
• Do not operate the gate by remote control unless they are in view.
• Do not attempt to block or interfere with the gate movement during operation.
• Under no circumstances should you attempt to modify the gate automation system.
• Ensure that your gate is serviced at 3 to 12 month intervals (dependent on number of openings) by your installation/
maintenance company.
• Report any signs of malfunction to your installation/maintenance company immediately.
• In the case of malfunction, isolate the power supply, release any additional locking mechanism, manually open the
gate (see manual release instruction booklet) and call your installation/maintenance company.
• If you are in any doubt regarding the operation of your gate, call your installation/maintenance company.

ATS: TYPICAL GATE SETUP
1
7
8
9
2
5
34
6
OUTSIDE OF GATES
INSIDE OF GATES
1ATS Motor 4Flashing Light (optional) 72nd set of Photocells (optional)
2Control Panel 5Selector Keypad (optional) 8Mechanical End Stop (not supplied)
3Reception Antenna 6Photocells (on outside of gate posts) 9Photocell column (optional accessory)
CONTROL PANEL
PHOTOCELLS
• The control panel should be mounted in an accessible position and not directly behind the gates, to avoid a
potential crushing hazard.
• Use cable glands to connect the devices to the control panel. One of these must be used exclusively for the
power supply cable.
• All holes should be sealed to avoid ingression and maintain the IP54 protection rating.
Only a competent service provider should open the enclosure
and adjust the settings.
• The photocells are used in pairs, one transmitter and one receiver.
• They should be installed between 500-600mm from the ground, facing each other.
• Power for the photocells is taken from the control panel 24v AC.
• The maximum range of the photocell should always be observed.
When the photocell beam is broken, the control panel can be programmed on how to react.
Please see ‘Safety’ section for more information.

ATS30AGS: GEOMETRY
• The greater the motor angle, the greater
the opening speed and the slower the
gear motor’s thrust.
• The smaller the motor angle, the slower
the opening speed and the greater the
gear motor’s thrust.
• Lubricate the bushing and fit it into one of the holes on the post bracket.
• The bracket holes allow the opening angle to be changed.
Opening A (mm) B (mm) E (mm) F (mm) C max. (mm)
90°130 130 960 1220 50
90°150 220 910 1290 150
90°120 270 890 1300 200
120°180 130 910 1300 50
Preliminary checks
Side hung gate GEOMETRY (3m)
Tick
1. Check that the gate structure is sturdy enough, the hinges work eciently and that there is
no friction between the fixed and moving parts
2. Make sure that measurement Cdoes not exceed the value shown in the reference table
3. Make sure that you have fitted opening and closing mechanical gate stops
OUTward OPENING gates
For outward opening gate geometry
please refer to the full Installation Manual.
A
C
B
60
60
E
F

ATS: MANUAL RELEASE
The ATS telescopic swing gate operators have a manual release lock beneath a hatch on
the top of the motors.
To manually release the gates:
1. Open the hatch covering the lock A.
2. Insert release key into lock Band turn clockwise C.
3. With your other hand firmly open the gate. The gate should be manually released. Now fully open the gate carefully at
the same speed as the automatic operator.
4. To re-engage, close the gate and turn the key back to its original position D. Attempt to manually move the gate to
ensure it is fully engaged.
Basic Maintenance: Hints & Tips
• Open manual release cover & spray locking
mechanism with suitable penetrating lubricant.
• Lubricate gate hinges.
• Manually release the gates at least once per month.
ALWAYS isolate the power supply as
instructed by your installer (even in a
power cut).
Release any additional locking
device fitted to the gate (eg. electric
lock etc).
a B C
D

ATS-P3: wiring diagram
L N U V W X Y E E3 10 11 S 1 2 3 3P 457 2 C1 CX B1 B2TS 10
L1T CT 0 12 24 L2T
2FC1 FA2 FC2
FA1
L2T L1T1 2 3 4
012 24
ZA3P
Control Panel
ATS30AGS
Gate motors
Cable/length
1m - 20m = 3 Core 1.5mm
20m - 30m = 3 Core 2.5mm
+ -
10 2 TX C NC TX 2
RX TX
DIR
Photocells
Cable/length
RX 4 Core 0.5mm Flex
TX 4 Core 0.5mm Flex
1m - 30m
AF43S
Plug-in
TOP-A433N
Antenna
Cable/length
RG58
Max. 5m
Mains Supply
230 V AC
Cable/length
1m - 20m = 3 Core 1.5mm
20m - 30m = 3 Core 2.5mm
The Earth cable should
be connected to the
motor chassis.

ZA3P: QUICK START GUIDE
Should the gates not operate as suggested above,
call CAME helpline 0115 921 0430 for technical support.
Important!
Ensure the wiring is complete (refer to the wiring diagram) & any required physical stops are set before
commencing with programming Tick
1. Power on the control panel.
2. Disable total stop – Permanent link wire between terminal 1& 2.
3. If no safety device has been connected to the C1 terminal then disable the safety input C1 -
Permanent link wire between terminal 2& C1.
4. Disable safety input CX – Dip switch 8on.
5. Set all other dip switches off.
6. Check the motor directions
Enable maintained action – Dip switch 6on.
Hold a wire between terminal 2& 3.
The gates should open, if not reverse the motor cables relating to the motor that is closing
for motor 2 (Connections X, Y)
for motor 1 (connections U, V)
Disable maintained action – Dip switch 6off
7. Set the ATS microswitch end stops
Unlock both motors on the manual release
Adjust the TL potentiometer to the maximum clockwise position.
Set both gates to their closed positions
For each gate motor complete the following steps
Send a closing command pulse using a link wire between terminal 2& 4.
While the motor is running, turn the rod marked C
anticlockwise until the motor stops running.
Set both gates to their open positions
For each motor complete the following steps
Send an opening command pulse using a link wire between terminal 2& 3.
While the motor is running, turn the rod marked A
clockwise until the motor stops running.
Note. 20 complete turns of the rod is equal to 10mm of movement of the micro switch. By default the motor run time is set to 120s, if the
motor times out before the micro switch has been reached an additional command will need to be sent to start the motor running again
so that the micro switch setup can be completed.
8. Set the TRM2 potentiometer all the way to minus (Anticlockwise).
9. Adjust the TL potentiometer to the 4 O’clock position
10. Check the gate operation by pulsing across connections 2& 4, the gate will close.
Safety inputs should now be configured and the gate force tested as required.
Please refer to the full manual to complete the commissioning.
Potentiometers Dip Switches
The installation must be carried out
by skilled and qualified personnel

ZA3P: QUICK START GUIDE
Should the gates not operate as suggested above,
call CAME helpline 0115 921 0430 for technical support.
Important!
Ensure the wiring is complete (refer to the wiring diagram) & any required physical stops are set before
commencing with programming Tick
1. Power on the control panel.
2. Disable total stop – Permanent link wire between terminal 1& 2.
3. If no safety device has been connected to the C1 terminal then disable the safety input C1 -
Permanent link wire between terminal 2& C1.
4. Disable safety input CX – Dip switch 8on.
5. Set all other dip switches off.
6. Check the motor directions
Enable maintained action – Dip switch 6on.
Hold a wire between terminal 2& 3.
The gates should open, if not reverse the motor cables relating to the motor that is closing
for motor 2 (Connections X, Y)
for motor 1 (connections U, V)
Disable maintained action – Dip switch 6off
7. Set the ATS microswitch end stops
Unlock both motors on the manual release
Adjust the TL potentiometer to the maximum clockwise position.
Set both gates to their closed positions
For each gate motor complete the following steps
Send a closing command pulse using a link wire between terminal 2& 4.
While the motor is running, turn the rod marked C
anticlockwise until the motor stops running.
Set both gates to their open positions
For each motor complete the following steps
Send an opening command pulse using a link wire between terminal 2& 3.
While the motor is running, turn the rod marked A
clockwise until the motor stops running.
Note. 20 complete turns of the rod is equal to 10mm of movement of the micro switch. By default the motor run time is set to 120s, if the
motor times out before the micro switch has been reached an additional command will need to be sent to start the motor running again
so that the micro switch setup can be completed.
8. Set the TRM2 potentiometer all the way to minus (Anticlockwise).
9. Adjust the TL potentiometer to the 4 O’clock position
10. Check the gate operation by pulsing across connections 2& 4, the gate will close.
Safety inputs should now be configured and the gate force tested as required.
Please refer to the full manual to complete the commissioning.
Potentiometers Dip Switches
The installation must be carried out
by skilled and qualified personnel
ZA3P: transmitters
Should the transmitter not operate as suggested above,
call CAME helpline 0115 921 0430 for technical support.
add a transmitter button
1. Press and hold the CH1 button, the PROG. LED starts flashing rapidly.
2. While keeping the CH1 button held down press and release a button on a transmitter
The PROG. LED goes solid to signal the successful saving of the code.
3. Release the CH1 key.
A maximum of 25 individual buttons can be saved.
remove all transmitters
1. Press and hold the CH1 and CH2 buttons simultaneously until the PROG. LED stays lit
All previously saved transmitter buttons will be removed from the memory of the control board.
L N U V W X Y E E3 10 11 S 1 2 3 3P 457 2 C1 CX B1 B2TS 10
L1T CT 0 12 24 L2T
2FC1 FA2 FC2
FA1
L2T L1T1 2 3 4
012 24
L N U V W X Y E E3 10 11 S 1 2 3 3P 457 2 C1 CX B1 B2TS 10
L1T CT 0 12 24 L2T
2FC1 FA2 FC2
FA1
L2T L1T1 2 3 4
012 24
Ensure the AF card is fitted (refer to the wiring diagram).

ZA3P: SAFETY
C1 REOPENING DURING CLOSING
• When the automation is in its closing cycle and the safety circuit is triggered the automation will stop and reverse its motion until it reaches its
fully open position again.
• If the auto closing option is enabled and the safety is no longer triggered the auto closing countdown will commence, once completed the
automation will start the closing cycle again.
• If the auto closing option is not enabled the automation will return to the fully open position awaiting another activation from a command device.
FUNCTIONS > C1 Input, CX Input
SAFETY INPUTS
CX RECLOSING DURING OPENING
• When the automation is in its opening cycle and the safety circuit is triggered the automation will stop and reverse its motion until it reaches its
fully closed position again.
• Once the automation has reached the fully closed position it will require another activation from a command device to restart.
CX PARTIAL STOP
• When the automation is in its opening cycle and the safety circuit is triggered the automation will stop.
• If the auto closing option is enabled and the safety is no longer triggered the auto closing countdown will commence, once completed the
automation will start closing the device.
If during the reverse motion a different safety is triggered the automation will perform the appropriate action for the new triggered
safety, should multiple safeties be triggered at the same time the automation will be halted at its current position.
OR
The above sequence will be attempted 3 times before the automation is halted, the automation will then
require activation from a command device to restart.

ATS-P3: ACCESSORIES
For more kit accessories please contact Sales on 0115 9210 430
Code(s) Description
RADIO KEYPAD SELECTORS
806SL-0170 SELT1W4G - Surface-mounted, 433.92 MHz radio-frequency keypad selector, 12-keys, with blue backlighting. 25 savable
codes and password to access the programming mode. Settable in Rolling Code or Fixed Code mode. RAL7024 Grey colour.
806SL-0180 SELT1W8G - Surface-mounted, 868.35 MHz radio-frequency keypad selector, 12-keys, with blue backlighting. 25 savable
codes and password to access the programming mode. Settable in Rolling Code or Fixed Code mode. RAL7024 Grey colour.
001AF868 Plug-in 868.35 MHz radio frequency control card.
Required for 806SL-0180.
BLUETOOTH SELECTORS
806SL-0210 SELB1SDG1 - Surface-mounted with blue backlighting, for 15 users. RAL7024 Grey colour.
806SL-0240 SELB1SDG2 - Surface-mounted with blue backlighting, for 50 users. RAL7024 Grey colour.
806SL-0250 SELB1SDG3 - Surface-mounted with blue backlighting, for 250 users. RAL7024 Grey colour.
HARDWIRED KEYPAD SELECTORS
806SL-0280 SELT1BDG - Surface-mounted 12 button Bus keypad with blue backlighting.
RAL7024 Grey colour.
806SL-0290 SELT2BDG - Flush-mounted 12 button Bus keypad with blue backlighting.
RAL7024 Grey colour.
806SL-0370 S0002P - External, two channel, 12 - 24 V AC - DC IP54 control card for keypads.
Required for 806SL-0280 and 806SL-0290.
TOP - FIXED CODE
8K06TS-002 TOPD4FXM - pack of 6 dual-frequency 4 button transmitters with self-learning function.
PHOTOCELLS
Surface mounted. Synchronised beam, multiple pairs of photocells can be applied to the same system,
even at double height and/or close to each other - with no interference issues (cross talk).
001DIR10 Pair of 12 - 24 V AC - DC outdoor photocells - range 10m.
001DIR20 Pair of 12 - 24 V AC - DC outdoor photocells - range 20m.
001DIR30 Pair of 12 - 24 V AC - DC outdoor photocells - range 30m.
PHOTOCELL column
001DIRL Natural finish aluminium post. H = 500mm
001DIRLN Black anodised aluminium post. H = 500mm
001DIRCG Silver RAL9006, PVC post. H = 500mm
ZA3P: SAFETY
C1 REOPENING DURING CLOSING
• When the automation is in its closing cycle and the safety circuit is triggered the automation will stop and reverse its motion until it reaches its
fully open position again.
• If the auto closing option is enabled and the safety is no longer triggered the auto closing countdown will commence, once completed the
automation will start the closing cycle again.
• If the auto closing option is not enabled the automation will return to the fully open position awaiting another activation from a command device.
FUNCTIONS > C1 Input, CX Input
SAFETY INPUTS
CX RECLOSING DURING OPENING
• When the automation is in its opening cycle and the safety circuit is triggered the automation will stop and reverse its motion until it reaches its
fully closed position again.
• Once the automation has reached the fully closed position it will require another activation from a command device to restart.
CX PARTIAL STOP
• When the automation is in its opening cycle and the safety circuit is triggered the automation will stop.
• If the auto closing option is enabled and the safety is no longer triggered the auto closing countdown will commence, once completed the
automation will start closing the device.
If during the reverse motion a different safety is triggered the automation will perform the appropriate action for the new triggered
safety, should multiple safeties be triggered at the same time the automation will be halted at its current position.
OR
The above sequence will be attempted 3 times before the automation is halted, the automation will then
require activation from a command device to restart.

CAME S.p.A.
Came cancelli automatici S.p.A.
is certied for Quality and Environment
UNI EN ISO 9001
UNI EN ISO 14001
BS OHSAS 18001
© ATSP3QS1021 - 2021 - EN
YOU MAY NOT EVEN PARTIALLY REPRODUCE THIS DOCUMENT
CAME RESERVES THE RIGHT TO MAKE ANY CHANGES TO THIS DOCUMENT AT ANY TIME
THE DATA AND INFORMATION SHOWN IN THIS CATALOGUE ARE SUBJECT TO CHANGE WITHOUT OBLIGATION TO GIVE PRIOR NOTICE BY CAME S.P.A, E&OE
CAME BPT - North
Unit 1B
Sills Road
Willow Farm Business Park
Castle Donington
DE74 2US
Tel: [phone]
CAME BPT - South
Liberta House
Maxted Road
Maylands Ind. Est.
Hemel Hempstead
Herts
HP2 7DX
Tel: [phone]
CAME BPT - Ireland
Unit 9
The Westway Centre
Ballymount
Dublin 12
Tel: [phone]