Cameo ZENIT W600 D SMD User manual

USER´S MANUAL
BEDIENUNGSANLEITUNG
MANUEL D´UTILISATION
MANUAL DE USUARIO
INSTRUKCJA OBSŁUGI
MANUALE D´USO
ZENIT®W600 D SMD
OUTDOOR SMD LED WASH LIGHT
WITH SEGMENT CONTROL - DAYLIGHT VERSION
CLZW600DSMD

CONTENTS / INHALTSVERZEICHNIS / CONTENU / CONTENIDO / TREŚĆ /
CONTENUTO
ENGLISH
INFORMATION ON THIS USER MANUAL 6
APPROPRIATE USE 6
DEFINITIONS AND SYMBOL EXPLANATIONS 6
SAFETY INSTRUCTIONS 7
NOTES ON PORTABLE OUTDOOR DEVICES 11
INCLUDED 11
INTRODUCTION 11
CONNECTIONS, OPERATING AND DISPLAY ELEMENTS 12
OPERATION 14
SET-UP AND INSTALLATION 22
CARE, MAINTENANCE AND REPAIR 22
OPTIONAL ACCESSORIES 24
DMX TECHNOLOGY 25
TECHNICAL DATA 27
EXPLANATION OF IP PROTECTION CLASS 28
MINIMUM DISTANCE TO ILLUMINATED SURFACE 29
MINIMUM DISTANCE TO NORMALLY FLAMMABLE MATERIALS 29
DISPOSAL 29
MANUFACTURER’S DECLARATIONS 30
DEUTSCH
INFORMATIONEN ZU DIESER BEDIENUNGSANLEITUNG 31
BESTIMMUNGSGEMÄSSER GEBRAUCH 31
BEGRIFFS- UND SYMBOLERKLÄRUNGEN 32
SICHERHEITSHINWEISE 32
HINWEISE FÜR ORTSVERÄNDERLICHE OUTDOOR-GERÄTE 37
LIEFERUMFANG 37
EINFÜHRUNG 38
ANSCHLÜSSE, BEDIEN- UND ANZEIGEELEMENTE 38
BEDIENUNG 41
AUFSTELLUNG UND MONTAGE 48
PFLEGE, WARTUNG UND REPARATUR 49
OPTIONALES ZUBEHÖR 51
DMX TECHNIK 52
TECHNISCHE DATEN 54
ERLÄUTERUNGEN ZUR IP-SCHUTZART 55
MINDESTABSTAND ZUR BELEUCHTETEN FLÄCHE 56
MINDESTABSTAND ZU NORMAL ENTFLAMMBAREN MATERIALIEN 56
ENTSORGUNG 56
HERSTELLERERKLÄRUNGEN 57

FRANÇAIS
INFORMATIONS CONCERNANT LE PRÉSENT MANUEL 58
UTILISATION CONFORME 58
EXPLICATIONS DES TERMES ET DES SYMBOLES 58
CONSIGNES DE SÉCURITÉ 59
REMARQUES CONCERNANT LES APPAREILS D’EXTÉRIEUR MOBILES 64
CONTENU DE LA LIVRAISON 64
PRÉSENTATION 65
RACCORDEMENTS, ÉLÉMENTS DE COMMANDE ET D’AFFICHAGE 65
UTILISATION 68
INSTALLATION ET MONTAGE 77
ENTRETIEN, MAINTENANCE ET RÉPARATION 77
ACCESSOIRES DISPONIBLES EN OPTION 79
TECHNOLOGIE DMX 80
CARACTÉRISTIQUES TECHNIQUES 82
EXPLICATIONS RELATIVES À L’INDICE DE PROTECTIONIP 83
DISTANCE MINIMALE DE LA SURFACE ÉCLAIRÉE 84
DISTANCE MINIMALE AVEC DES MATÉRIAUX NORMALEMENT INFLAMMABLES 84
MISE AU REBUT 84
DÉCLARATIONS DU FABRICANT 85
ESPAÑOL
INFORMACIÓN SOBRE ESTE MANUAL 86
USO PREVISTO 86
TÉRMINOS Y SÍMBOLOS 87
INSTRUCCIONES DE SEGURIDAD 87
INDICACIONES PARA EQUIPOS PORTÁTILES DE EXTERIOR 92
VOLUMEN DE SUMINISTRO 92
INTRODUCCIÓN 93
CONEXIONES, ELEMENTOS DE MANDO Y ELEMENTOS DE VISUALIZACIÓN 93
FUNCIONAMIENTO 96
INSTALACIÓN Y MONTAJE 104
CUIDADO, MANTENIMIENTO Y REPARACIÓN 105
ACCESORIOS OPCIONALES 107
TECNOLOGÍA DMX 108
DATOS TÉCNICOS 110
EXPLICACIÓN SOBRE LA CLASE DE PROTECCIÓN IP 111
DISTANCIA MÍNIMA CON RESPECTO A LA SUPERFICIE ILUMINADA 112
DISTANCIA MÍNIMA CON RESPECTO A MATERIALES NORMALMENTE INFLAMABLES 112
ELIMINACIÓN 112
DECLARACIONES DEL FABRICANTE 113
CONTENTS / INHALTSVERZEICHNIS / CONTENU / CONTENIDO / TREŚĆ /
CONTENUTO

POLSKI
INFORMACJE DOTYCZĄCE NINIEJSZEJ INSTRUKCJI OBSŁUGI 114
UŻYTKOWANIE ZGODNE Z PRZEZNACZENIEM 114
OBJAŚNIENIA TERMINÓW I SYMBOLI 115
ZASADY BEZPIECZEŃSTWA 115
UWAGI DOTYCZĄCE PRZENOŚNEGO SPRZĘTU ZEWNĘTRZNEGO 120
ZAKRES DOSTAWY 120
WPROWADZENIE 121
PRZYŁĄCZA, ELEMENTY OBSŁUGI I WSKAŹNIKI 121
OBSŁUGA 124
USTAWIANIE I MONTAŻ 131
CZYSZCZENIE, KONSERWACJA I NAPRAWY 132
OPCJONALNE AKCESORIA 134
TECHNIKA DMX 135
DANE TECHNICZNE 137
OBJAŚNIENIA DOTYCZĄCE STOPNIA OCHRONY IP 138
MINIMALNA ODLEGŁOŚĆ OD POWIERZCHNI OŚWIETLONEJ 139
MINIMALNA ODLEGŁOŚĆ OD NORMALNIE ŁATWOPALNYCH MATERIAŁÓW 139
UTYLIZACJA 139
DEKLARACJE PRODUCENTA 140
ITALIANO
INFORMAZIONI SUL PRESENTE MANUALE DI ISTRUZIONI 141
UTILIZZO CONFORME 141
SPIEGAZIONE DI CONCETTI E SIMBOLI 142
INDICAZIONI SULLA SICUREZZA 142
AVVERTENZE PER DISPOSITIVI PORTATILI PER ESTERNI 147
DOTAZIONE 147
INTRODUZIONE 148
CONNETTORI, ELEMENTI DI COMANDO E VISUALIZZAZIONE 148
UTILIZZO 151
INSTALLAZIONE E MONTAGGIO 158
CURA, MANUTENZIONE E RIPARAZIONE 159
ACCESSORI OPZIONALI 161
TECNOLOGIA DMX 162
DATI TECNICI 164
SPIEGAZIONI SULLA PROTEZIONE IP 165
DISTANZA MINIMA DALLA SUPERFICIE ILLUMINATA 166
DISTANZA MINIMA DAI MATERIALI NORMALMENTE INFIAMMABILI 166
SMALTIMENTO 166
DICHIARAZIONI DEL PRODUTTORE 167
CONTENTS / INHALTSVERZEICHNIS / CONTENU / CONTENIDO / TREŚĆ /
CONTENUTO

DMX
DMX CONTROL / DMX STEUERUNG / PILOTAGE DMX / CONTROL DMX /
STEROWANIE DMX / CONTROLLO DMX 168
PIXEL SEGMENTS / PIXEL SEGMENTE 177
CONTENTS / INHALTSVERZEICHNIS / CONTENU / CONTENIDO / TREŚĆ /
CONTENUTO

6
DMX
ITALIANO
POLSKI
ESPAÑOL
FRANCAIS
DEUTSCHENGLISH
ENGLISH
YOU HAVE MADE THE RIGHT CHOICE!
This device has been developed and manufactured to the highest quality standards to ensure
many years of problem-free operation. Please read this manual carefully to be able to use your
new Cameo product quickly and optimally. Further information about Cameo Light is available on
our website CAMEOLIGHT.com.
INFORMATION ON THIS USER MANUAL
•Read the safety instructions and the entire manual carefully before use.
•Observe the warnings on the device and in the user manual.
•Always keep the user manual within reach.
•If you sell or pass on the device, it is important to ensure you pass on this user manual, as it is
an integral part of the product.
APPROPRIATE USE
This product is a device for event technology!
The product has been developed for professional use in the field of event technology and is not
suitable for use as domestic lighting.
Furthermore, this product is only intended for qualified users with specialist knowledge of event
technology!
Use of the product outside the specified technical data and operating conditions is considered
inappropriate!
Liability for damage and third-party damage to persons and property due to inappropriate use is
excluded!
The product is not suitable for:
• persons (including children) with limited physical, sensory or mental abilities or lack of experi-
ence and knowledge.
• children (children must be instructed not to play with the device).
DEFINITIONS AND SYMBOL EXPLANATIONS
1. HAZARD: The word HAZARD, possibly in combination with a symbol, indicates situations in
which there is an immediate danger or risk of potentially fatal injury.
2. WARNING: The word HAZARD, possibly in combination with a symbol, indicates situations in
which there is an immediate danger or risk of potentially fatal injury.
3. CAUTION: The word CAUTION, possibly in combination with a symbol, indicates situations or
conditions that could result in injury.
4. ATTENTION: The word ATTENTION, possibly in combination with a symbol, indicates situations
or conditions that could result in damage to property and/or the environment.

7
DMX DEUTSCHFRANCAIS
ESPAÑOL ENGLISH
ITALIANO POLSKI
This symbol identifies hazards that can cause electric shock.
This symbol identifies danger points or hazardous situations.
This symbol indicates hazards caused by hot surfaces.
This symbol indicates hazards caused by intense light sources.
This symbol indicates a device in which there are no user-replaceable parts.
This symbol indicates additional information relating to use of the product.
SAFETY INSTRUCTIONS
HAZARD:
1. Do not open the device and do not perform any modifications.
2. If your device no longer functions properly, if liquids or objects get inside it or if it
has been damaged in any other way, switch it off immediately and disconnect it
from the mains. The device may be repaired only by authorised repair technicians.
3. For devices of protection class 1, the protective conductor must be connected
correctly. Never disconnect the protective conductor. Devices of protection class 2
do not have a protective conductor.
4. Ensure that live cables are not kinked or otherwise mechanically damaged.
5. Never bypass the device fuse.
WARNING:
1. The device must not be put into operation if it shows obvious signs of damage.
2. The device may only be installed in a voltage-free state.
3. If the power cord of the device is damaged, the device must not be used.
4. Permanently connected mains cables may only be replaced by a qualified person.

8
DMX
ITALIANO
POLSKI
ESPAÑOL
FRANCAIS
DEUTSCHENGLISH
CAUTION:
1. Do not put the device into operation immediately if it has been exposed to
extreme temperature fluctuations (for example, after transportation). Moisture
and condensation can damage the device. Do not switch on the device until it has
reached room temperature.
2. Ensure that the voltage and frequency of the mains supply match the values
specified on the device. If the device has a voltage selector switch, do not connect
the device until it has been set correctly. Use only suitable power cables.
3. To disconnect the device from the mains on all poles, it is not sufficient to press
the on/off switch on the device.
4. Make sure that the fuse used corresponds to the type printed on the device.
5. Ensure that suitable measures have been taken against overvoltage (e.g. lightning
strikes).
6. Observe the specified maximum output current on devices with a Power Out con-
nection. Ensure that the total current consumption of all connected devices does
not exceed the specified value.
7. Replace pluggable mains cables with original cables only.
HAZARD
1. Choking hazard! Plastic bags and small parts must be kept out of reach of per-
sons (including children) with reduced physical, sensory or mental capabilities.
2. Risk of falling! Make sure that the device is securely installed and will not fall
down. Only use suitable stands or mountings (particularly for fixed installations).
Make sure that accessories are correctly installed and secured. Ensure that appli-
cable safety regulations are observed.
WARNING:
1. Use the device in the prescribed manner only.
2. Operate the device using only accessories of the type recommended and supplied
by the manufacturer.
3. Observe safety regulations applicable in your country during installation.
4. After connecting the device, ensure that all cables are routed so as to avoid dam-
age or accidents, such as from tripping.
5. Always observe the specified minimum distance to normally flammable materials!
Unless explicitly stated, the minimum distance is 0.3 m.
6. Always observe the minimum distance to the illuminated surface that can be read
on the device!

9
DMX DEUTSCHFRANCAIS
ESPAÑOL ENGLISH
ITALIANO POLSKI
CAUTION:
1. Moving components such as mounting brackets may become jammed.
2. In the case of devices with motor-driven components, there is a risk of injury due
to the movement of the device. Sudden movement of the device can cause shock
reactions.
3. The housing surface of the device can become very hot during regular operation.
Ensure that accidental touching of the housing is not possible. Always allow the
device to cool down sufficiently before removal, maintenance work and charging
etc.
CAUTION:
1. Do not install or use the device in the vicinity of radiators, accumulators, stoves,
or other heat sources Ensure that the device is always installed in such a way
that it is sufficiently cooled and cannot overheat.
2. Do not place ignition sources, such as burning candles, near the device.
3. Ventilation openings must not be covered and fans must not be blocked.
4. Use the original packaging or packaging provided by the manufacturer for trans-
port.
5. Avoid shocks or impacts to the device.
6. Observe the IP rating and the ambient conditions such as temperature and hu-
midity according to the specifications.
7. Devices can be further developed on an ongoing basis. In the event of deviating
information on operating conditions, performance or other device properties
between the user manual and the device labelling, the information on the device
always has priority.
8. The device is not suitable for tropical climate zones and for operation at over
2000 m above sea level.
9. Unless explicitly stated, the device is not suitable for operation under marine
conditions.
CAUTION! IMPORTANT INFORMATION REGARDING LIGHTING PRODUCTS!
1. Never look directly into the beam of light, not even for a short period of time.
2. Never look into the beam of light using optical devices such as a magnifying
glass.
3. Stroboscopic effects may cause epileptic seizures in those susceptible!

10
DMX
ITALIANO
POLSKI
ESPAÑOL
FRANCAIS
DEUTSCHENGLISH
4. A permanently installed lamp is installed in this lighting unit which must not be
replaced by the user. In the event of a fault, please contact your sales partner.
SIGNAL TRANSMISSION BY RADIO (e.g. W-DMX or audio radio systems):
The quality and performance of wireless signal transmissions generally depends on
the ambient conditions.
The following factors can impact range and signal stability, for example:
Shielding (e.g. masonry, metal structures, water)
High volume of radio traffic (e.g. powerful wireless LAN networks)
Interference
Electromagnetic radiation (e.g. LED video screens, dimmers)
All range specifications refer to free-field application with visual contact and without
interference!
The operation of transmission systems is subject to official regulations. These may
vary from region to region and must be checked by the operator before use (e.g.
radio frequency and transmission power).
WARNING: Devices with wireless signal transmission are not suitable for use in
sensitive areas in which radio operation can lead to potential detrimental effects.
These include:
•hospitals, health centres or other healthcare facilities that provide patient treat-
ment with skilled personnel and equipment.
•Hazardous areas Class I, II and III
•Restricted areas
•Military facilities
•Aircraft or vehicles
•Areas where the use of mobile phones is prohibited

11
DMX DEUTSCHFRANCAIS
ESPAÑOL ENGLISH
ITALIANO POLSKI
INCLUDED
Take the product out of the packaging and remove all packaging material.
Please check the completeness and integrity of the delivery and notify your distribution partner
immediately after purchase if the delivery is not complete or shows signs of damage.
With the package you purchased, you received:
XSpotlight
XMains cable
X2 Omega brackets
XUser manual
INTRODUCTION
ZENIT W600 D SMD PROFESSIONAL OUTDOOR WASHLIGHT
CLZW600DSMD
TRANSMISSION VIA W-DMX
WARNING:In general, wireless DMX transmission must not be used for applica-
tions involving safety-related factors that might result in personal injury or property
damage in the event of a failure.
This applies in particular to moving scene or traverse structures, DMX-controlled
motors/lifts or lifting devices for operating DMX-operated platform lifts, hydraulic
systems or comparable moving components.
Furthermore, wireless DMX transmission must not be used to trigger flame or pyro-
technic devices, explosion-driven effects, or to control gas or liquid effects. These
include CO2 cannons, confetti shooters, water effects or similar.
NOTES ON PORTABLE OUTDOOR DEVICES
1. Temporary operation! Event equipment is generally only designed for temporary
operation.
2. Continuous operation or permanent structural installation, particularly outdoors,
can impair the function, surfaces and seals and accelerate material fatigue.
3. Damage to the surface coating can impair the corrosion protection of the device.
A damaged surface coating (e.g. scratches) must be promptly restored by means
of suitable measures.

12
DMX
ITALIANO
POLSKI
ESPAÑOL
FRANCAIS
DEUTSCHENGLISH
CONTROL FUNCTIONS:
1-channel, 2-channel, 3-channel, 4-channel, 6-channel, 12-channel, 15-channel, 18-channel,
48-channel, 54-channel, 63-channel DMX control
Master / slave operation
Standalone operation
W-DMX™
FEATURES:
576 Single SMD Daylight LEDs. IP65 protection rating. DMX512. W-DMX™. 16-bit dimmer. 4 dim-
mer curves. Adjustable LED PWM frequency. Fast Access Feature. 5-pin DMX connections. Plastic
feet. 2x Omega mounting brackets included. Operating voltage 100–240 V AC.
Barn-door available as an option.
The spotlight features the RDM standard (Remote Device Management). Remote device mana-
gement allows the user to view status and configuration of RDM terminals via an RDM-capable
controller.
CONNECTIONS, OPERATING AND DISPLAY ELEMENTS
656
42
31
1POWER IN
IP65 power input socket with rubber sealing cap. Operating voltage 100-240 V AC/50-60 Hz.
Connection via supplied power cable (when not in use, always close with rubber sealing cap).
2POWER OUT
IP65 power output socket with rubber sealing cap. Facilitates power supply to other CAMEO
spotlights. Ensure that the total current consumption of all connected devices does not exceed
the value specified on the device in amperes (A) (when not in use, always close with the rubber
sealing cap).

13
DMX DEUTSCHFRANCAIS
ESPAÑOL ENGLISH
ITALIANO POLSKI
3DMX IN
Male IP65 5-pin XLR socket for connecting a DMX control device (e.g. DMX console; when not in
use, always close with the rubber sealing cap).
4DMX OUT
Female IP65 5-pin XLR socket for sending DMX control signal (when not in use, always close with
the rubber sealing cap).
5OLED DISPLAY
The OLED display shows the currently activated mode (main display), the menu items in the
selection menu and the numerical value or status in the various menu items.
6TOUCH-SENSITIVE CONTROLS
MODE
Press MODE to access the main menu. Press again or repeatedly to return to the main display.
ENTER
Press ENTER to access the menu level to make value or status changes, and to access the sub-
menus. Confirm value or status changes by pressing ENTER.
UP and DOWN
– Select individual menu items in the main menu (DMX address, operating mode etc.) and in the
submenus. Allow changes to the status or value in a menu item, such as the DMX address, as
required.
PRESSURE EQUALISATION ELEMENT
The pressure equalisation element to prevent condensation inside the housing is in the device
base, behind the cable feed for the LED unit. In order to ensure its proper function, the element
must be protected from contamination.
HOUSING FAN
The 3 housing fans and the heat sink are on the back of the LED unit. In order to ensure good air
circulation, do not cover the device and clean it regularly.
PLEASE NOTE
•As soon as the spotlight is connected is supplied with power, the following are displayed in suc-
cession: "Welcome to Cameo", the model name and the software version. During the start-up
process, the previously set operating mode is activated and the spotlight is ready for operation
after a short time.
•Before changing device settings, ensure that the control panel is dry and free of dust in order not
to impair its functionality.
•If one of the DMX operating modes is activated and there is no DMX signal to the DMX input, the

14
DMX
ITALIANO
POLSKI
ESPAÑOL
FRANCAIS
DEUTSCHENGLISH
currently programmed DMX address is displayed and the characters on the display will begin to
flash.
•The main display is activated automatically if there is no input in the space of approximately one
minute.
•Fast Access Feature: In order to simplify the menu guide, the device has an intelligent menu
structure that allows direct access to previously selected menu items and submenu items.
1. Press MODE and ENTER simultaneously for direct access to the last-edited submenu item,
where you can make changes instantly as required (DMX starting address and all modes).
2. Press MODE to go directly to the last selected and edited menu item. If you now repeatedly
press ENTER, you can access the submenu items to make individual settings (DMX start ad-
dress and all operating modes).
•The display can be rotated through 180° by pressing UP when the main display is visible.
•To quickly change a value (e.g. DMX start address), press and hold the UP or DOWN button.
CAUTION: In order to provide protection from spraying water, in accordance with
protection class IP65, special IP65-rated XLR connectors must be used correctly
with the DMX input and output sockets, or they must be closed using the rubber
sealing caps. When connected correctly, or when sealed correctly with the rubber
sealing caps, the POWER IN and POWER OUT sockets are protected from spraying
water, as in accordance with IP65.
OPERATION
MAIN DISPLAY
The main display shows the following information: Current mode (in the example: DMX mode) and
W-DMX™ status.
DMX Address
001
W-DMX™status
Current operating mode
W-DMX™
1. To pair with W-DMX™ compatible transmitters, enable W-DMX™ in the device settings (Set-
tings -> Wireless Setting -> W-DMX On Off -> On) and reset the W-DMX™ module (Receive
Reset -> Yes). Start the pairing process as described in the operating instructions of the W-D-
MX™ transmitter. Pairing is then completed automatically.

15
DMX DEUTSCHFRANCAIS
ESPAÑOL ENGLISH
ITALIANO POLSKI
2. Pair a group of W-DMX™ devices to create a DMX universe with them. First decouple all
devices that should form the group (Settings -> Wireless Setting -> Receive Reset). Then
select a CLZW600 with a DMX controller via DMX cable and select "Transmit" in the settings
(Settings -> Wireless Setting -> Operating Mode -> Transmit). Select "Receive" in the settings
of the W-DMX™ device that you want to control via W-DMX™ (Settings -> Wireless Setting ->
Operating Mode -> Receive), and pair it by selecting "Link" in the settings of the DMX cable
controlled CLZW600, then confirm your selection (Settings -> Wireless Setting -> Link -> Link).
Pairing is then completed automatically.
3. It is also possible to create a connected group of W-DMX™ devices via W-DMX™, and operate
them in master/slave mode. First decouple all devices that should form the group (Settings
-> Wireless Setting -> Receive Reset). In the settings (Settings -> Wireless Setting -> Ope-
rating Mode) of the master unit select "Transmit", and in the settings of the slave units select
"Receive". On the master unit select "Link" (Settings -> Wireless Setting -> Link -> Link) and
confirm your selection by pressing ENTER. Pairing of the devices is then completed automati-
cally. Select standalone mode in the master unit and use this to control the slave units (same
model).
W-DMX™ STATUS
G3 G4S
W-DMX™
deactivated
W-DMX™
activated as
receiver,
not paired
W-DMX™
activated as
receiver and is
paired to device,
Transmitter is
switched off or
out of range
W-DMX
activated and is
paired to device,
no DMX signal
W-DMX™
activated as
receiver and is
paired to device,
DMX signal is
present
W-DMX™ and
transmission
mode G3 is
enabled
Up arrow =
Send operation
Down arrow
= Receive
operation
Arrow flashes=
Pairing process
Flashing stops =
Paired
W-DMX™ and
transmission
mode G4S
activated
Up arrow =
Send operation
Down arrow
= Receive
operation
Arrow flashes=
Pairing process
Flashing stops =
Paired
SETTING DMX START ADDRESS (DMX ADDRESS)
Press MODE to access the main menu (--- Menu ---). Using UP and DOWN, select the menu item
DMX Address (observe arrow) and confirm with ENTER. The display will show a three-digit num-
ber field and you can use the UP and DOWN controls to configure the desired DMX start address.
Confirm the entry with ENTER and press MODE to return to the main display (in the example,
"DMX address 001").
---------------- Menu ----------------
DMX Address
DMX Mode
Stand Alone
Slave
Settings
System Info
DMX Address
001
001
5xx
-

MF MF DMX DMX DEUTSCH FRANCAIS ESP AÑOL ENGLISH IT ALIANO POLSKI IT ALIANO POLSKI ESP AÑOL FRANCAIS DEUTSCH ENGLISH CONFIGURINGDMXMODE(DMX MODE) PressMODEtoaccessthe main menu (--- Menu ---). UsingUPandDOWN, selectthemenuitem DMXMode (obser vearro w)andconfirmwithENTER. Inthesubmenu, youcanno wselectthe desiredDMXmodewithUP and DOWN. Confirmyourselectionwith ENTER. T ableswiththechannelassignments can be found in these instructionsunderDMXCONTROL. CONFIGUREST AND ALONEMODE PressMODEtoaccessthe main menu (--- Menu ---). UsingUPandDOWN, selectthemenuitem Stand Alone (obser vearro w)andconfirmwithENTER. Inthesubmenu, youcanno wselectthe stand-alonemodes Static , Pix el andthetimerfunction T imerwithUPandDOWN. Confirmyour selectionwithENTER. ST A TICMODE(ST A TIC) Sta ticmodeallo wstheDimmerandStrobe functions to be adjusted directly on the device with valuesbetween000to255, similartoaDMX control unit. Inthisway, anindividualscenecan be crea tedwithoutanadditionalDMX controller . Select Static modeasperthe procedure previously describedinSETTINGST AND ALONEMODEandconfirmwith ENTER. No wuseUPandDOWN to selectthemenuitemyou wish to edit (obser vearro w)andconfirmwithENTER. Thedisplaywill no wsho wathree-digitnumberfield, andyoucanuse UP and DOWN to configure the desired valuebetween000and255. ConfirmwithENTER. PIXELMODE( Pix els ) Pixelmodeallo wsyoutosetdimmers, pa tternsandspeeddirectlyon the device with values from 000to255. Dynamicpa tternscanbefoundfrom value 006 to 098 and sta ticpa tternsfrom128 to234. Thespeedofthed ynamicpa tternsissetfrom006 (fast) to 126 (slo w)andinthereverse directionfrom128(slo w)to255(fast)(000 – 005 and 127 = stop). Select Pix el modeasperthe procedurepreviouslydescribedinSETTING ST AND ALONEMODEandconfirmwith ENTER. No w useUPandDOWNto select the menu item you wish to edit (obser vearro w)andconfirmwith ENTER. The display will no w sho w a three-digit number field, and you can use UP and DOWN to configurethedesiredvaluebetween 000 and 255. ConfirmwithENTER. TIMERFUNCTION (T imer) Thetimerfunctionallo wsthestandalonemode Static tobetimercontrolled in such a way tha t thefade-intimecanbe set from 0 to 60 minutes, thedwelltimefrom 1 to 24 hours and the fade - -outtimefrom0to 60 minutes. T imecontrolstartsimmedia telyafteractiva tingthetimerfunction inthepreviouslyactiva tedstandalonemodeandremains active even if the spotlight is s witched offandrestarted. Select T i m e r bymeansofthe procedure described above under CONFIGURE ST ANDALONEMODE andconfirmwithENTER. No wselect “F adeIn”, “Dwell T ime” or “F adeOut” fortheindividualset - tings(obser vearro w)andconfirmwithENTER. Thedisplaywillsho wathree-digitnumberfield in eachcase. UseUPandDOWN to set the value as required from 000 to 060 or 001 to 024. Confirm bypressingENTERa gain. Onceallsettingsha vebeenconfiguredasrequired, activa tethetimer functionbyselectingthesubmenu item “T imerOn/Off ” usingUPandDOWN, confirmwithENTER, select “On” and confirm a gain with ENTER (to deactiva te the timer function, please select “Off ” andconfirm). Pleasenote: The timer function is suitable for use in master/sla ve mode via cable and W -D - MX™.

MF MF DMX DMX DEUTSCH FRANCAIS ESP AÑOL ENGLISH IT ALIANO POLSKI IT ALIANO POLSKI ESP AÑOL FRANCAIS DEUTSCH ENGLISH CONFIGURINGDMXMODE(DMX MODE) PressMODEtoaccessthe main menu (--- Menu ---). UsingUPandDOWN, selectthemenuitem DMXMode (obser vearro w)andconfirmwithENTER. Inthesubmenu, youcanno wselectthe desiredDMXmodewithUP and DOWN. Confirmyourselectionwith ENTER. T ableswiththechannelassignments can be found in these instructionsunderDMXCONTROL. CONFIGUREST AND ALONEMODE PressMODEtoaccessthe main menu (--- Menu ---). UsingUPandDOWN, selectthemenuitem Stand Alone (obser vearro w)andconfirmwithENTER. Inthesubmenu, youcanno wselectthe stand-alonemodes Static , Pix el andthetimerfunction T imerwithUPandDOWN. Confirmyour selectionwithENTER. ST A TICMODE(ST A TIC) Sta ticmodeallo wstheDimmerandStrobe functions to be adjusted directly on the device with valuesbetween000to255, similartoaDMX control unit. Inthisway, anindividualscenecan be crea tedwithoutanadditionalDMX controller . Select Static modeasperthe procedure previously describedinSETTINGST AND ALONEMODEandconfirmwith ENTER. No wuseUPandDOWN to selectthemenuitemyou wish to edit (obser vearro w)andconfirmwithENTER. Thedisplaywill no wsho wathree-digitnumberfield, andyoucanuse UP and DOWN to configure the desired valuebetween000and255. ConfirmwithENTER. PIXELMODE( Pix els ) Pixelmodeallo wsyoutosetdimmers, pa tternsandspeeddirectlyon the device with values from 000to255. Dynamicpa tternscanbefoundfrom value 006 to 098 and sta ticpa tternsfrom128 to234. Thespeedofthed ynamicpa tternsissetfrom006 (fast) to 126 (slo w)andinthereverse directionfrom128(slo w)to255(fast)(000 – 005 and 127 = stop). Select Pix el modeasperthe procedurepreviouslydescribedinSETTING ST AND ALONEMODEandconfirmwith ENTER. No w useUPandDOWNto select the menu item you wish to edit (obser vearro w)andconfirmwith ENTER. The display will no w sho w a three-digit number field, and you can use UP and DOWN to configurethedesiredvaluebetween 000 and 255. ConfirmwithENTER. TIMERFUNCTION (T imer) Thetimerfunctionallo wsthestandalonemode Static tobetimercontrolled in such a way tha t thefade-intimecanbe set from 0 to 60 minutes, thedwelltimefrom 1 to 24 hours and the fade - -outtimefrom0to 60 minutes. T imecontrolstartsimmedia telyafteractiva tingthetimerfunction inthepreviouslyactiva tedstandalonemodeandremains active even if the spotlight is s witched offandrestarted. Select T i m e r bymeansofthe procedure described above under CONFIGURE ST ANDALONEMODE andconfirmwithENTER. No wselect “F adeIn”, “Dwell T ime” or “F adeOut” fortheindividualset - tings(obser vearro w)andconfirmwithENTER. Thedisplaywillsho wathree-digitnumberfield in eachcase. UseUPandDOWN to set the value as required from 000 to 060 or 001 to 024. Confirm bypressingENTERa gain. Onceallsettingsha vebeenconfiguredasrequired, activa tethetimer functionbyselectingthesubmenu item “T imerOn/Off ” usingUPandDOWN, confirmwithENTER, select “On” and confirm a gain with ENTER (to deactiva te the timer function, please select “Off ” andconfirm). Pleasenote: The timer function is suitable for use in master/sla ve mode via cable and W -D - MX™.

18
DMX
ITALIANO
POLSKI
ESPAÑOL
FRANCAIS
DEUTSCHENGLISH
SLAVE MODE CONFIGURATION
Press MODE to access the main menu (--- Menu ---). Using UP and DOWN, select the menu item
Slave (observe arrow) and confirm with ENTER. Connect the slave and the master units (same
model, same software version) with a DMX cable and enable a standalone mode (Static, Pixel) on
the master unit. The slave unit will now follow the master unit. If there is no control signal, the
display characters will flash. Flashing stops as soon as a control signal is present.
Mode
Slave
---------------- Menu ----------------
DMX Address
DMX Mode
Stand Alone
Slave
Settings
System Info
SYSTEM SETTINGS (SETTINGS)
Press MODE to access the main menu (--- Menu ---). Using UP and DOWN, select the menu item
Settings (observe arrow) and confirm with ENTER.
---------------- Menu ----------------
DMX Address
DMX Mode
Stand Alone
Slave
Settings
System Info
This will take you to the submenu for setting the following submenu items (selection with UP and
DOWN, confirm with ENTER):
Settings
Wireless
Settings
= W-DMX
settings
(wireless
DMX)
W-DMX On/
Off
On = W-DMX activated
Off = W-DMX disabled
Operating
Mode
Receive = W-DMX module as receiver
Transmit = W-DMX module as transmitter
Transmitting
Mode
G3 = G3 transmission standard
G4S = G4S transmission standard
Link Link = pair with W-DMX devices. W-DMX must
be activated on all devices and the pairing
must be picked up by a transmitter (Receive
Reset).
Unlink = unpair all devices
Receive
Reset
No = do not retain transmitter pairing
Yes = retain transmitter pairing

19
DMX DEUTSCHFRANCAIS
ESPAÑOL ENGLISH
ITALIANO POLSKI
Display
Reverse
= Display
rotation
On Display is rotated by 180° (e.g. for overhead
installation)
Off No rotation of the display
Display Back-
light
= Display
lighting
On permanently on
Off Deactivation after approximately 1 minute of
inactivity
DMX Fail = Operating
status when
DMX signal
fault occurs
Hold last command is retained
Blackout Activates blackout
Full On Spotlight switches to full on
Stand-alone Spotlight switches to stand-alone mode
Dimmer
Curve
= Dimmer
curve
Linear Light intensity increases linearly with DMX
value
Exponential Light intensity can be finely adjusted at lower
DMX values and broadly adjusted at higher
DMX values
Logarithmic Light intensity can be broadly adjusted at low-
er DMX values and finely adjusted at higher
DMX values
S-curve Light intensity can be finely adjusted at lower
and higher DMX values and broadly adjusted
at medium DMX values
Power Mode = Operating
mode
Normal Constant brightness
Boost Brief maximum brightness (approx. 3 seconds)
Dimmer
response
= Dimmer
response
LED Lamp responds abruptly to changes in DMX
value
Halogen Spotlight behaves like a halogen spotlight with
soft brightness changes
Autolock = Automatic
locking of
controls
On Automatic locking of the controls after approx-
imately 1 minute of inactivity. After attempted
input the display shows: "Locked!"
Unlock: press and hold UP and DOWN simulta-
neously for approx. 5 seconds
Off Automatic locking of the controls is disabled
PWM Fre-
quency
= LED PWM
frequency:
800 Hz/1200
Hz/2000 Hz/
3600 Hz/12
kHz/25 kHz
Configuration of LED PWM frequency

20
DMX
ITALIANO
POLSKI
ESPAÑOL
FRANCAIS
DEUTSCHENGLISH
linear
DMX value
Light intensity
exponential
DMX value
Light intensity
logarithmic
DMX value
Light intensity
S-curve
DMX value
Light intensity
Dimmer curves
Mirror Pixel = Invert/mirror
arrangement
of pixel
segments
(function
only for DMX
operation)
Off No reflection/inversion
Invert Background -> Pattern, Pattern -> Back-
ground
Horizontal Mirror horizontally
Vertical Mirror vertically
Horizontal +
Invert
Mirror and invert horizontally
Vertical +
Invert
Mirror and invert vertically
Fan = Adjust fan
control
Auto Automatic adjustment of the fan performance
Max. Intensity Maximum fan capacity for maximum bright-
ness
Low Noise Extra-quiet fan with reduced brightness
Factory Reset = Resets to
factory
setting
Reset Now! Reset to factory settings:
ENTER -> "Reset Now!" -> ENTER Press
MODE to stop.