Canon BW PCL PRINTER KIT-J1 Operating and maintenance manual

Sep 14 2005
Installation Procedure
Canon BW
PCL PRINTER KIT-J1

Application
This manual has been issued by Canon Inc. for qualified persons to learn technical theory, in-
stallation, maintenance, and repair of products. This manual covers all localities where the prod-
ucts are sold. For this reason, there may be information in this manual that does not apply to
your locality.
Corrections
This manual may contain technical inaccuracies or typographical errors due to improvements or
changes in products. When changes occur in applicable products or in the contents of this manual,
Canon will release technical information as the need arises. In the event of major changes in the
contents of this manual over a long or short period, Canon will issue a new edition of this manual.
The following paragraph does not apply to any countries where such provisions are inconsistent
with local law.
Trademarks
The product names and company names used in this manual are the registered trademarks of the
individual companies.
Copyright
This manual is copyrighted with all rights reserved. Under the copyright laws, this manual may
not be copied, reproduced or translated into another language, in whole or in part, without the
written consent of Canon Inc.
COPYRIGHT © 2001 CANON INC.
Printed in Japan
Caution
Use of this manual should be strictly supervised to avoid disclosure of confidential information.

Introduction
Symbols Used
This documentation uses the following symbols to indicate special information:
Symbol Description
Indicates an item of a non-specific nature, possibly classified as Note, Caution, or Warning.
Indicates an item requiring care to avoid electric shocks.
Indicates an item requiring care to avoid combustion (fire).
Indicates an item prohibiting disassembly to avoid electric shocks or problems.
Indicates an item requiring disconnection of the power plug from the electric outlet.
Indicates an item intended to provide notes assisting the understanding of the topic in ques-
tion.
Indicates an item of reference assisting the understanding of the topic in question.
Provides a description of a service mode.
Provides a description of the nature of an error indication.
Memo
REF.

Introduction
The following rules apply throughout this Service Manual:
1. Each chapter contains sections explaining the purpose of specific functions and the rela-
tionship between electrical and mechanical systems with reference to the timing of operation.
In the diagrams, represents the path of mechanical drive; where a signal name accom-
panies the symbol , the arrow indicates the direction of the electric signal.
The expression "turn on the power" means flipping on the power switch, closing the front
door, and closing the delivery unit door, which results in supplying the machine with power.
2. In the digital circuits, '1'is used to indicate that the voltage level of a given signal
is "High", while '0' is used to indicate "Low".(The voltage value, however, differs from
circuit to circuit.) In addition, the asterisk (*) as in "DRMD*" indicates that the DRMD
signal goes on when '0'.
In practically all cases, the internal mechanisms of a microprocessor cannot be checked in
the field. Therefore, the operations of the microprocessors used in the machines are not
discussed: they are explained in terms of from sensors to the input of the DC controller PCB
and from the output of the DC controller PCB to the loads.
The descriptions in this Service Manual are subject to change without notice for product im-
provement or other purposes, and major changes will be communicated in the form of Service
Information bulletins.
All service persons are expected to have a good understanding of the contents of this Service
Manual and all relevant Service Information bulletins and be able to identify and isolate
faults in the machine."

Contents
Contents
Chapter 1 Installation Procedure
1.1 Checking components ....................................................................................................................................... 2
1.1.1Checking the Contents................................................................................................................................. 2
1.2 Installation procedure......................................................................................................................................... 3
1.2.1Mounting to the Host Machine.................................................................................................................... 3
1.2.2Checking the Connection ............................................................................................................................ 6

Contents

Chapter 1 Installation
Procedure

Chapter 1
2
1.1 Checking components
1.1.1 Checking the Contents 0010-7372
F-1-1
[1] 32MB ROM 1 pc.
[2] 256MB RAM 1 pc.
[3] Screw (binding; M3X4) 1 pc.
[4] User software CD-ROM 1 pc.
[5] Release Note 1 pc.
[6] User's Manual CD-ROM 1 pc.
[1] [2] [3]
[4] [5] [6]

Chapter 1
3
1.2 Installation procedure
1.2.1 Mounting to the
Host Machine 0010-7632
1) Turn off the main power switch, and disconnect the
power plug.
2) Remove the rear cover [1].
- 4 screws [2]
F-1-2
3) Remove the rear left cover [1].
- 3 screws [2]
F-1-3
4) If a Super G3 Fax Board-T1 is found, disconnect
the connector [1] of the IP-modem cable.
If an optional Super G3 Fax Board-T1 is found, the
SDRAM and the super capacitor remain powered to
back up the image memory (even after the main power
switch has been turned off and the power plug has
been disconnected).
Be sure to disconnect the IP modem cable before re-
moving the RAM.
F-1-4
5) Remove the RAM cover [1].
- 4 screws [2]
F-1-5
6) Remove the 128MB RAM [1] in the direction of
[A].
- 2 locking levers [2] (shift in the direction of [B])
[1]
[2]
[1]
[2]
[1]
[2]
[1]

Chapter 1
4
F-1-6
7) If a UFRII LT PRINTER KIT-J2 is installed, per-
form steps 7-1) and 7-2).
7-1) Remove the LAN cover [1].
- 4 screws [2]
F-1-7
7-2) Disconnect the connector [1] of the IP-LAN ca-
ble.
- 1 wire saddle [2]
- IP-LAN cable [3]
F-1-8
8) Disconnect the soft ID cable [1].
- 1 cable clamp [2]
F-1-9
9) Release the claw [1] of the cable guide, and free the
cable guide [2] in upward direction.
F-1-10
[2] [1]
[B]
[B]
[A]
[2]
[1]
[2]
[1] [2]
[3]
[1]
[2]
[1]
[2]

Chapter 1
5
10) Remove the IP cover [1].
- 10 screws [2]
F-1-11
11) Shift the 2 locking levers [1] back to their initial
position.
F-1-12
12) Connect the connector [1] of the 32MB ROM to
the connector [2] of the IP PCB.
- 1 screw (binding; M3x4) [3]
F-1-13
13) Attach the IP cover you removed in step 10).
When attaching the IP cover, take care not to damage
the grounding plate [2] by the USB port [1].
Also, after attaching the IP cover, check to make sure
that the grounding plate is in firm contact with the
USB port.
F-1-14
14) Put all the parts that you have removed back in
place.
- cable guide
- soft ID cable
- IP-LAN cable (if a UFRII LT PRINTER KIT-J2
is mounted)
15) Attach the LAN cover removed in step 7-1). (if a
[2]
[2]
[2]
[1]
[1]
[1] [2]
[3]
[1]
[2] [2]

Chapter 1
6
UFRII LT PRINTER KIT-J2 is mounted)
When attaching the LAN cover, take care not to dam-
age the grounding plate [2] by the LAN port [1].
Also, after attaching the LAN cover, check to make
sure that the grounding plate is in firm contact with the
LAN port.
F-1-15
16) Mount the 256MB RAM [1].
F-1-16
17) Put back the parts that have been removed.
- RAM cover
- the connector of the IP-modem cable (if a Super
G3 Fax Board-T1 is mounted)
- rear left cover
- rear cover
18) Connect the power plug, and turn on the main
power switch.
1.2.2 Checking the Con-
nection 0010-7789
When you have installed the kit, go through the fol-
lowing to make sure that it is properly recognized:
1) Start service mode.
User Mode key > 2 > 8 > Use Mode key
In response, [#SSSW] appears.
2) Press [ ] 5 times. When [REPORT] has ap-
peared, press [OK].
3) Press [ ] once. When [REPORT OUTPUT]
has appeared, press [OK].
4) Press [ ] 5 times. When [SPEC LIST] has ap-
peared, press [OK].
5) See that a SPEC REPORT is printed out. Check to
be sure that 'PCL' is 'ON'.
[1]
[2] [2]
[1]

Sep 14 2005