Canon imageFORMULA DR-G2140 User manual

SERVICE
MANUAL
imageFORMULA
DR-G2140/DR-G2140 USB
DR-G2110/DR-G2110 USB
DR-G2090
Canon
November 17,2021
Rev.0.4
COPYRIGHT © 2021CANON ELECTRONICS INC.
CANONimageFORMULA DR-G2140DR-G2110DR-G2090 Rev. 0.4PRINTED INU.S.A.

COPYRIGHT © CANON ELECTRONICS INC. 2018
Use of this manual should be
strictly supervised to avoid
disclosure of confidential
information.

COPYRIGHT © CANON ELECTRONICS INC. 2018 CANON DR-G2140/G2110/G2090 FIRST EDITION
PREFACE
Quality Assurance Center
Canon Electronics Inc.
This Service Manual describes necessary basic information for field service and maintenance for main-
taining the product quality and functions of this machine.
Contents
Chapter 1: General description
Product specifications, name of parts, operation method
Chapter 2: Functions and operation
Description of operation of machine system and electrical system by function
Chapter 3: Disassembly and reassembly
Disassembly method, reassembly method
Chapter 4: Installation and maintenance
Installation method, maintenance method
Chapter 5: Troubleshooting
Error display and troubleshooting
Appendix: General diagram etc.
Information in this manual is subject to change. Notification of such changes will be given in Service
Information Bulletins.
Thoroughly read the information contained in this Service Manual and the Service Information Bulletins
to gain a correct and deeper understanding of the machine. This is one way of fostering response for
ensuring prolonged quality and function, and for investigating the cause of trouble during troubleshooting.

CONTENTS
COPYRIGHT © CANON ELECTRONICS INC. 2018 CANON DR-G2140/G2110/G2090 FIRST EDITION
CHAPTER 1
GENERAL DESCRIPTION
I. PRODUCT SPECIFICATIONS .....................1-1
1. Features...................................................1-1
2. Specifications...........................................1-2
3. Precautions .............................................. 1-6
II. NAME OF PARTS........................................1-7
1. Front Side ................................................1-7
2. Rear Side .................................................1-8
3. Operation Panel .......................................1-8
III. USER OPERATION ....................................1-9
1. Preparation of Trays................................. 1-9
2. Job Function ..........................................1-10
3. CaptureOnTouch.................................... 1-11
4. Paper Jam, Skew and Staple Detection
Handling ................................................1-13
5. User Mode .............................................1-15
CHAPTER 2
FUNCTIONS & OPERATION
I. OUTLINE ......................................................2-1
1. Basic Configuration..................................2-1
2. Feed Path ................................................ 2-2
3. Motor Drive ..............................................2-3
4. List of Sensors ......................................... 2-4
5. Electrical Circuits .....................................2-6
6. Timing Chart ............................................2-7
II. READING SYSTEM...................................2-10
1. Outline....................................................2-10
2. Image Reading....................................... 2-11
3. Shading.................................................. 2-12
III. FEED SYSTEM.........................................2-13
1. Outline....................................................2-13
2. Pickup Tray Elevation ............................ 2-14
3. Separation Mechanism .......................... 2-15
4. Feed Error Detection..............................2-16
5. Staple Detection.....................................2-17
IV. CONTROL SYSTEM.................................2-18
1. Control PCB ...........................................2-18
2. Drive System Block Diagram .................2-19
3. Image Processing Control......................2-20
4. New Binarizing .......................................2-21
5. Network Scanning ..................................2-22
V. POWER SUPPLY ......................................2-23
1. Power Supply.........................................2-23
VI. OPTION ....................................................2-24
1. Imprinter .................................................2-24
2. Flatbed Scanner Unit .............................2-25
VII. ELECTRICAL PARTS LAYOUT...............2-26
1. Motor, Fan, Solenoid..............................2-26
2. PCB, Sensor, Unit ..................................2-28
VIII. PARTS LAYOUT ON EACH PCB ...........2-30
1. Control PCB ...........................................2-30
2. Main Drive PCB .....................................2-31
3. Sub-Drive PCB.......................................2-32
4. Power PCB.............................................2-33
5. Eject PCB...............................................2-34
CHAPTER 3
DISASSEMBLY &
REASSEMBLY
I. REPLACED BY USERS ...............................3-1
1. Pickup Roller............................................3-1
2.Feed Roller...............................................3-1
3. Retard Roller ............................................3-2
II. EXTERNAL COVERS ..................................3-3
1. Control PCB Cover ..................................3-3
2. Right Cover Assembly..............................3-3
3. Operation Panel .......................................3-4
4. Left Cover Assembly ................................3-5
5. Top Cover.................................................3-6
6. Pickup Tray Unit.......................................3-7
7. Eject Tray Unit..........................................3-7
8. Upper Front Cover ...................................3-8
9. Rear Cover...............................................3-9
i

COPYRIGHT © CANON ELECTRONICS INC. 2018 CANON DR-G2140/G2110/G2090 FIRST EDITION
III. UPPER UNIT-1 (MECHANICAL RELATION)
............................................................... 3-10
1. Pickup Unit .............................................3-10
2. Pickup Roller Cover................................3-11
3. Upper Entrance Guide............................3-12
4. Pull-in Upper Roller ................................3-12
5. Registration Upper Roller .......................3-13
6. Reading Upper Roller.............................3-14
7. Platen Upper Roller ................................3-15
8. U-turn Upper Roller ................................3-16
9. Eject Follower Roller ..............................3-16
10. Eject Tray Extension.............................3-17
11. Imprinter Cover .....................................3-18
12. Eject Document Guide .........................3-18
13. Entire Upper Unit ..................................3-19
IV. UPPER UNIT-2 (ELECTRICAL RELATION)
............................................................. 3-21
1. Main Drive PCB ......................................3-21
2. Ultrasonic Sensor PCB...........................3-21
3. Feed Motor .............................................3-22
4. Pickup Motor...........................................3-23
5. Pickup Up/Down Motor...........................3-23
V. UPPER UNIT-3 (READING RELATION).. 3-24
1. Upper Reading Unit................................3-24
2. Shading Motor ........................................3-25
3. Upper Reading Glass Assembly ...........3-26
VI. BASE UNIT-1 (MECHANICAL RELATION)
............................................................... 3-27
1. Pickup Document Guide.........................3-27
2. Tray Drive Box ........................................3-28
3. Blind Cover .............................................3-29
4. Pickup Tray Plate ...................................3-30
5. Lower Front Cover..................................3-30
6. Lower Entrance Guide............................3-31
7. Right Belt ................................................3-31
8. Left Front Belt .........................................3-32
9. Left Rear Belt..........................................3-32
10. Pull-in Lower Roller ..............................3-33
11. Registration Lower Roller .....................3-33
12. Platen Lower Roller ..............................3-34
13. Reading Lower Roller ...........................3-35
14. Pre U-turn Lower Roller........................3-36
15. U-turn Lower Roller (Middle) ................3-37
16. U-turn Lower Roller (Rear) ...................3-37
17. Eject Drive Unit.....................................3-38
18. Eject Drive Roller..................................3-38
VII. BASE UNIT-2 (ELECTRICAL RELATION)
............................................................... 3-39
1. Control PCB............................................3-39
2. Sub-Drive PCB .......................................3-40
3. Staple PCB .............................................3-40
4. Power PCB .............................................3-41
5. Ultrasonic Drive PCB..............................3-42
6. Eject PCB ...............................................3-42
7. Document Sensor PCB ..........................3-43
8. Main Motor..............................................3-44
9. Tray Motor ..............................................3-45
10. Separation Motor ..................................3-46
11. Eject Motor............................................3-46
12. Exhaust Fan .........................................3-47
13. Cooling Fan ..........................................3-48
VIII. BASE UNIT-3 (READING RELATION) .. 3-49
1. Lower Reading Unit ................................3-49
2. Shading Motor ........................................3-50
3. Lower Reading Glass Assembly............3-51
CHAPTER 4
INSTALLATION &
MAINTENANCE
I. INSTALLATION............................................. 4-1
1. Choosing Location....................................4-1
2. Unpacking And Installation .......................4-2
3. Imprinter Installation Procedure ...............4-8
II. PARTS REPLACEMENT........................... 4-12
1. Periodically Replaced Parts ...................4-12
2. Consumable Goods (Commercial Goods)
..............................................................4-14
3. Consumable Parts (Service Parts) .........4-14
III. MAINTENANCE ....................................... 4-15
1. User Maintenance ..................................4-15
ii

COPYRIGHT © CANON ELECTRONICS INC. 2018 CANON DR-G2140/G2110/G2090 FIRST EDITION
2. Service Maintenance .............................4-16
CHAPTER 5
TROUBLESHOOTING
I. ERROR DISPLAY .........................................5-1
1. Main Body ................................................ 5-1
2. Computer ................................................. 5-3
II. SERVICE MODE .........................................5-4
1. Outline......................................................5-4
2. Preparation ..............................................5-9
3. How to Start and Finish .........................5-10
4. Application Information .......................... 5-11
5. Simulation Mode .................................... 5-11
A. Information............................................. 5-12
1. Scanner Name....................................5-12
2. Background color................................5-12
3. Firmware version ................................5-13
4. Error History........................................5-13
5. Serial Number.....................................5-14
6. Sleep Mode.........................................5-14
7. Auto Power OFF .................................5-15
8. Counter ...............................................5-15
9. Write File.............................................5-17
B. Adjustment............................................. 5-18
1. All ........................................................5-19
2. Scaling (Manual).................................5-20
3. Registration (Manual) .........................5-23
4. Density (Auto) .....................................5-24
5. Density (Manual) ................................5-25
C. Motor / Sensor....................................... 5-26
1. CIS, LCD, Buzzer ...............................5-26
2. Move ...................................................5-27
3. Position ...............................................5-27
4. CoverOpen .........................................5-28
5. Panel...................................................5-29
6. SD Card ..............................................5-29
7. USB 3.1 ..............................................5-30
8. Imprinter Door.....................................5-30
9. Others .................................................5-31
D. Firmware................................................5-31
1. Firm Registration ................................5-32
2. Firm Load............................................5-34
3. Network Firmware...............................5-35
E. Analog....................................................5-36
1. Analog Sensor ....................................5-36
2. Write File.............................................5-36
F. Scan Test................................................5-37
1. Scan....................................................5-37
G. Imprinter ................................................5-38
H. Network .................................................5-39
1. Obtainment of Log Files......................5-40
III. TROUBLESHOOTING LIST .....................5-42
1. Operation Failures .................................5-42
2. Image Failures .......................................5-42
IV. OPERATION TROUBLESHOOTING........5-43
1. Power Does Not Turn ON ......................5-43
2. No Scanner is Found .............................5-44
3. Scanning Does Not Start .......................5-45
4. Scanner Does Not Feed Properly ..........5-46
5. Scanning Speed is Slow ........................5-47
V. IMAGE TROUBLESHOOTING ..................5-48
1. Completely Black, Completely White,
All Streaks.............................................5-49
2. Too Dark, Too Light ................................5-49
3. Black Borders Around Image .................5-50
4. Image Skews .........................................5-50
5. Streaks on Image...................................5-51
6. Outer Areas of Image Disappear ...........5-51
7. Wrong Image Size .................................5-52
8. Text Invisible...........................................5-52
VI. AFTER REPLACING PARTS ...................5-53
APPENDIX
I. GENERAL DIAGRAM ...................................A-1
II. LIST OF SPECIAL EQUIPMENT .................A-2
iii

CHAPTER 1
GENERAL DESCRIPTION
COPYRIGHT © CANON ELECTRONICS INC. 2018 CANON DR-G2140/G2110/G2090 FIRST EDITION
I. PRODUCT OUTLINE ...............................1-1
II. NAME OF PARTS ....................................1-7
III. USER OPERATION .................................1-9

COPYRIGHT © CANON ELECTRONICS INC. 2018 CANON DR-G2140/G2110/G2090 FIRST EDITION 1-1
CHAPTER 1 GENERAL DESCRIPTION
I. PRODUCT SPECIFICATIONS
1. Features
1) Succeeding models of DR-G1130/G1100
2) 3 models suitable for each usage (Scanning speed at gray and color, 200dpi)
DR-G2140: A4 landscape 140 ppm/280 ipm, A3 85 ppm/170 ipm
DR-G2110: A4 landscape 110 ppm/220 ipm, A3 70 ppm/140 ipm
DR-G2090: A4 landscape 90 ppm/180 ipm, A3 60 ppm/120 ipm
3) High-durability
Expect life 16 million sheets (A4 copy paper)
4) High-speed USB interface
Support USB3.1 Gen1 (Super Speed)
5) Network scanning with wired LAN
Supported by DR-G2140/G2110 network models
6) New CIS unit and DR processor
7) New binary processing “Active thresholding”
“Windows” is a trademark of Microsoft Corporation in the U.S. and other countries.
Other company names and product names mentioned in this document are registered trademarks or trade-
marks of the respective companies.

1-2 COPYRIGHT © CANON ELECTRONICS INC. 2018 CANON DR-G2140/G2110/G2090 FIRST EDITION
CHAPTER 1 GENERAL DESCRIPTION
2. Specifications
1) Appearance/Installation
No.
Item
Specifications
1
Type of scanner
Desktop type sheet-fed scanner
2
Document path
U-turn path
3
Dimensions
Tray closed：480（W）×569（D）×315（H）mm
*See details at following.
4
Weight
25 kg (Main body only)
5
Power supply
1) 100V model：AC100V，50/60Hz
2) 120V model：AC120V，60Hz
3) 200V model：AC220-240V，50/60Hz
* Power PCB supports AC100 to 240V, 50/60Hz.
6
Power consumption
1) Maximum operation：66.5W
2) Sleep mode：3.5W
3) Power switch OFF：0.2W
7
External interface
1) USB 3.1 (Standard B connector)
USB 3.1 Gen1 Super-Speed/USB 2.0 Hi-Speed support
2) Wired LAN （RJ45 connector）
10Base-T/100Base-TX/1000Base-T support
* Only one of above can be used at the same time.
* The wired LAN is for the network model only.
8
Expected product life
(In-house information
only)
One of the following two items, whichever comes first.
1) 5 years
2) 16 million sheets (A4 copy paper)
* Replace parts if necessary.
9
Installation
By service technicians
*Need 2 or more persons for carry the machine.
10
Bundle software
ISIS/TWAIN driver, CaptureOnTouch V4 Pro，
Driver setting tool, KOFAX SVRS
11
Consumable parts
(Commercial goods)
1) Exchange roller kit (Pickup/ Feed/ Retard rollers)
* Expected life 600,0000 sheets
2) Separation pad (Separation cover with pad)
* Expected life 6 million sheets
12
Type of scanner
1) Imprinter (Post type)
2) Flatbed scanner unit (FSU102、FSU201)
* No use for wired LAN connection.
3) Carrier sheets (A4)
4) Cleaning sheets
5) White platen rollers
Table 1-101

COPYRIGHT © CANON ELECTRONICS INC. 2018 CANON DR-G2140/G2110/G2090 FIRST EDITION 1-3
CHAPTER 1 GENERAL DESCRIPTION
External dimensions (unit: mm)
Figure 1-101

1-4 COPYRIGHT © CANON ELECTRONICS INC. 2018 CANON DR-G2140/G2110/G2090 FIRST EDITION
CHAPTER 1 GENERAL DESCRIPTION
2) Functions
No.
Item
Specifications
1
Sensor type
3 lines-CMOS contact image sensor (CIS), 600dpi
2
Effective reading width
308mm
3
Light source
3-color（RGB）LED, Both-side illumination
4
Background color
Black (White as option.)
5
Maximum scanning size
305 x 432 mm
* 3,000 or 5,588 mm maximum at long document mode.
6
Document size
1) Width: 50.8 to 305 mm
2) Length：70 to 432 mm
3) Weight (Thickness) ：20 to 209 g/m2 (0.04 to 0.25 mm)
* There are some limitations for special document.
7
Document storage
(Pickup tray)
1) A4 or smaller: 500 sheets or 48 mm height maximum
* 300 sheet maximum for DR-G2090.
2) A4 over: 200 sheets or 20 mm height maximum
8
Double feed detection
1) Length detection by registration sensor
2) Double feed detection by ultrasonic sensor (one pair)
9
Skew detection
Equipped
10
Staple detection
Equipped
11
Separation mode
1) Thin paper mode
2) Normal
3) High separation mode
12
Mode setting in driver
1) Binary: B&W/Error diffusion/ATE/ATE-II/Active threshold
2) Gray (8-bit)
3) Color (24-bit
13
Resolution setting in
driver
100x100dpi, 150x150dpi，200x200dpi，240x240dpi
300x300dpi，400x400dpi，600x600dpi
14
Scanning speed
Auto-size and skew detections are ON, it may differ de-
pending on the computer and function settings.
Model
Document
Mode
resolu-
tion
Simplex
((ppm)
Duplex
(ipm)
DR-G2140
A4
Landscape
Gray
(JPEG)
200dpi
140
280
300dpi
140
280
600dpi
38
76
Color
(JPEG)
200dpi
140
280
300dpi
140
280
600dpi
38
76
A4
Portrait
(Refer.)
Gray
(JPEG)
200dpi
110
220
300dpi
110
220
600dpi
30
60
Color
(JPEG)
200dpi
110
220
300dpi
110
220
600dpi
30
60
Table 1-102

COPYRIGHT © CANON ELECTRONICS INC. 2018 CANON DR-G2140/G2110/G2090 FIRST EDITION 1-5
CHAPTER 1 GENERAL DESCRIPTION
No.
Item
Specifications
14
(cont.)
DR-G2140
A3
(Refer.)
Gray
(JPEG)
200dpi
85
170
300dpi
80
160
600dpi
22
44
Color
(JPEG)
200dpi
85
170
300dpi
80
160
600dpi
22
22
DR-G2110
A4
Landscape
Gray
(PEG)
200dpi
110
220
300dpi
110
220
600dpi
30
60
Color
(JPEG)
200dpi
110
220
300dpi
110
220
600dpi
30
60
A4
Portrait
(Refer.)
Gray
(JPEG)
200dpi
90
180
300dpi
90
180
600dpi
25
50
Color
(JPEG)
200dpi
90
180
300dpi
90
180
600dpi
25
50
A3
(Refer.)
Gray
(JPEG)
200dpi
70
140
300dpi
70
140
600dpi
18
36
Color
(JPEG)
200dpi
70
140
300dpi
70
140
600dpi
18
22
DR-G2090
A4
Landscape
Gray
(JPEG)
200dpi
90
180
300dpi
90
180
600dpi
24
48
Color
(JPEG)
200dpi
90
180
300dpi
90
180
600dpi
24
48
A4
Portrait
(Refer.)
Gray
(JPEG)
200dpi
75
150
300dpi
75
150
600dpi
20
40
Color
(JPEG)
200dpi
75
150
300dpi
75
150
600dpi
20
40
A3
(Refer.)
Gray
(JPEG)
200dpi
60
120
300dpi
60
120
600dpi
15
30
Color
(JPEG)
200dpi
60
120
300dpi
60
120
600dpi
15
15
15
Operation
1) LCD: Monochrome, Backlight, 5 lines
2) Button: Power button, other 11 operation buttons
Table 1-103

1-6 COPYRIGHT © CANON ELECTRONICS INC. 2018 CANON DR-G2140/G2110/G2090 FIRST EDITION
CHAPTER 1 GENERAL DESCRIPTION
3. Precautions
This section describes items that require
particular care, for example, regarding human
safety.
These precautions must be observed.
The user should be explained the items that re-
late to user safety and instructed to take appro-
priate actions.
1) Power OFF in emergency
If such abnormal conditions as extraordi-
nary noise, smoke, heat and odor occur,
immediately unplug the power cord.
Be careful not to get clothing (ties, long
hair, etc.) caught in this machine as it may
cause injury. Should this occur, immedi-
ately unplug the power cord. Do not insert
fingers in the feed section while moving
the rollers.
2) Power OFF on disassembling
When disassembling and assembling are
performed, unplug the power cord.
3) Prohibition of modify
This machine must not arbitrarily be modi-
fied or remade. If it is, use of this machine
may be forcibly suspended.
To change the specifications or disassem-
ble and reassemble this machine, follow
the instructions described in this manual
and the service information.
4) Electromagnetic wave interference
This machine complies with some stand-
ards regarding electromagnetic wave in-
terference, such as VCCI and FCC. How-
ever, the user may have to take counter-
measures if the machine causes electro-
magnetic wave interference.
5) User Manual
Read each “User Manual” thoroughly prior
to use of this machine.
6) Disposal
Follow local regulations when disposing of
the product and parts. This product is sub-
ject to the WEEE Directive in Europe.
7) Movement
This machine weighs 25 kg. When lifting or
moving this machine, 2 persons must hold
it from both sides. Never lift it by one per-
son.
Figure 1-102

COPYRIGHT © CANON ELECTRONICS INC. 2018 CANON DR-G2140/G2110/G2090 FIRST EDITION 1-7
CHAPTER 1 GENERAL DESCRIPTION
II. NAME OF PARTS
1. Front Side
Figure 1-201

1Upper unit

2Imprinter cover

3Document eject tray

4Power switch

5Operation panel

6Document eject tray extension

7Document eject stopper

8Document eject guides

9Document feed guides

10
Document guide lock lever

11
Document feed tray (Pickup tray *)

12
Document feed tray extension & wire
Note:In this manual, the “Document feed tray”
may be mentioned as the “Pickup tray.”

1-8 COPYRIGHT © CANON ELECTRONICS INC. 2018 CANON DR-G2140/G2110/G2090 FIRST EDITION
CHAPTER 1 GENERAL DESCRIPTION
2. Rear Side
Figure 1-202

1Ventilation holes (Exhaust fan)

2Power connector

3Grounding terminal

4 USB connector (Type B)

5LAN connector (RJ-45)
3. Operation Panel
Figure 1-203

1Display panel

2Menu key

3 (left/right) keys

4▲▼ (up/down) keys

5Function key

6OK key

7Stop key

8Start key

9Back key

10
Job key

COPYRIGHT © CANON ELECTRONICS INC. 2018 CANON DR-G2140/G2110/G2090 FIRST EDITION 1-9
CHAPTER 1 GENERAL DESCRIPTION
III. USER OPERATION
This section presents an outline of the
user operations. Refer to the “User Manual”
of this machine for details.
1. Preparation of Trays
Before scanning documents, prepare for
the document feed tray and document eject
tray according to the documents.
1) Document feed tray
The height of the document feed tray can
be adjusted according to the number of
documents to be set and is set to the low-
est position as the initial value. It is
changed in user mode.
Figure 1-301
Adjust the position of the document feed
guides according to the document width.
Figure 1-302
Note:The right and left positions can be
changed by locking the document
guides. Refer to the “User Manual” for
details.
Pull out the tray extension according to
the document length. Open the extension
wire as required.
Figure 1-303

1-10 COPYRIGHT © CANON ELECTRONICS INC. 2018 CANON DR-G2140/G2110/G2090 FIRST EDITION
CHAPTER 1 GENERAL DESCRIPTION
2) Document eject tray
Hold both document guides and adjust
the positions according to the width of the
document to be set.
Figure 1-304
Note:The positions of the right and left docu-
ment guides of the document eject tray
can be changed independently of each
other.
Open the document eject tray extension
according to the document length. Raise
the document eject stopper as necessary.
Figure 1-305
2. Job Function
The job function select and executes
jobs (favorites) that have been registered
with CaptureOnTouch by pressing the job
key on the operation panel.
Refer to the “User Manual” for details.
1) Press the Job key on the operation panel.
Note: With USB connection, the Job selection
screen is displayed. With LAN connec-
tion, the PC selection screen is dis-
played.
Figure 1-306
Figure 1-307 (USB)
Figure 1-308 (LAN)

COPYRIGHT © CANON ELECTRONICS INC. 2018 CANON DR-G2140/G2110/G2090 FIRST EDITION 1-11
CHAPTER 1 GENERAL DESCRIPTION
2) With LAN connection, at first press the ▲
▼keys to select a computer for connec-
tion.
And press the OK key.
Figure 1-309 (LAN)
3) Press the ▲▼keys to select the job. And
then press the Start key.
Figure 1-310
3. CaptureOnTouch
This section describes how to scan using
the [Standard Scanning] in CaptureOnTouch.
Note:CaptureOnTouch is TWAIN compatible
application software.
1) Click the CaptureOnTouch icon on the
task bar.
Figure 1-311
2) Click the Select Scanner on the menu.
Figure 1-312
3) Select the scanner you are using and click
the OK.
Figure 1-313

1-12 COPYRIGHT © CANON ELECTRONICS INC. 2018 CANON DR-G2140/G2110/G2090 FIRST EDITION
CHAPTER 1 GENERAL DESCRIPTION
4) The main menu is displayed.
Note: There are two areas in the CaptureOn-
Touch main screen, the Scanning
Shortcut and the Standard Scanning.
Figure 1-314
5) Place the document in the scanner.
6) Click the select document panel for the
document to be scanned from the 1 Se-
lect document in the main screen.
Figure 1-315
7) Click the output panel for the scan image
application from the 2 Select output.
Figure 1-316
8) Click the Scan button. The scanning starts.
Figure 1-317
9) To check the scanned image, click the Fin-
ish button.
Figure 1-318