Canon KOMATSU D155AX User manual

Special Vehicle Series :03
Assembly Instructions
Bulldozer
Bulldozer
http://www.canon.com/c-park/en/
* This model was designed for
Papercraft and may differ from
the original in some respects.
View of completed model
T
ools
ools A
ssembly tip
ssembly tip
Key to symbols
Key to symbols
Scissors
Ruler, set square
Glue (Wood glue or craft glue recommend)
Exhausted ballpoint pen (out of ink)
Toothpicks (for use in applying glue)
Tweezers (useful for handling small parts)
Pencil
Pattern
Red dot
Green dot
Blue dot
Assembly instructions
Solid line
Dashed and
dottedline
Dotted line
Solid red line
Diagonal
grey lines
Mountain fold
Fold so that the printed
pattern faces outside.
Fold so that the printed
pattern faces inside.
Valley fold
Cut parts out
along this line.
Cut a notch
along this line.
Cut these areas
out.
Glue parts with the same
number together. (Numbersare
not printed on very small parts.)
Glue areas within the same
part together.
Glue
Insert
Glue tab
Reverse side of
paper
(without gluing)
Red arrow
Blue arrow
Light blue
Light grey
Glue, scissors and other tools may be dangerous to young children
so be sure to keep them out of the reach of young children.
Assembly Instructions: Nine A4 sheets (No. 1 to No. 9)
Build this model with careful reference to the Assembly Instructions.
Write the number of each part on the reverse side of the part in pencil
upon cutting it out, to be sure you can tell which part is which later.
Before gluing, crease the paper along
mountain and valley fold lines. Trace along
the folds with a ruler and an exhausted
ballpoint pen (out of ink) to get a sharper fold.
Make sure rounded sections are nice and stiff.
Glue to the reverse side of the
specified part.
The dots show where to glue
the pieces together. Glue the
pieces together as shown in the
following examples.
Some parts must be glued
together along the cut surfaces.
This denotes a part
that must be able to
move after the model
is completed.Be sure
to crease these parts
sufficiently.
Movable part

Assembly Instructions
Bulldozer
Assemble the cab.
Glue flaps a, b, c, and d in order.
Glue flaps a, b, c, and d in order.
Glue flaps a, b, c, and d in order.

Assembly Instructions
Bulldozer
Before assembly, cut out these tabs
and fold them using valley folds.
Don’t forget to cut this notch
out before assembly.
Glue flaps a, b, and c in order.
Insert the
convex tab.
Glue this piece in place after
first positioning it by matching
the arrows to the corners.
Use care when gluing these
pieces in place, to ensure
that the bottom is level.

Assembly Instructions
Bulldozer
Glue flaps a and b in order.
Inside
Inside
Outside Inside
Outside
Outside
Cross section
Inside
Outside
Inside
Outside
Cross section
Inside Outside
Cross section Cross section
Wrap part 64 around part
62 so the seam is on the
bottom, and glue it in place.
Make sure part 64 extrudes
toward the outside.
Wrap part 65 around part
63 so the seam is on the
bottom, and glue it in place.
Make sure part 65 extrudes
toward the outside.
Assemble the other side in the same way
(making the left and right sides symmetrical).

Assembly Instructions
Bulldozer
Refer to the cross-section
when assembling parts 22 and 29.
Cross section
Cross section
Cross section
Movable part
Assemble the other side in the same way
(making the left and right sides symmetrical).
This assembly does not include any parts
corresponding to part in assembly .
Curving the parts on the inside,
glue parts 66, 67, 68, 69, and 70
in position one spot at a time.
Aligning the bottom edges, glue these
parts in place in order, starting from
the center, and then finish this assembly
by gluing the top edge in place.

Assembly Instructions
Bulldozer
Cross section
Movable part
Make sure the arrows on part 37 are pointing
up and glue parts 44, 45, and 46 in place,
checking that each is positioned correctly.
Apply glue to the cutout areas
of the paper and attach to part
37 in a way that hides the glue spots.

Assembly Instructions
Bulldozer
Check the part position
and glue in place.
Cross section
Check the part position
and glue in place.
Cross section

Assembly Instructions
Bulldozer
Slightly spread out the arms that connect
to the sides of the main body and then insert
them into the holes on both sides.
Cross section
Check the part position and glue in place.

On parts with no glue tabs, apply glue to the cut
surface of the paper and glue this part to the body
of the Bulldozer, concealing the glue tabs.
(Refer to the photograph of the completed model.)
Finished!
Last, assemble the nameplate
and display it together with
your model.
Bulldozer
Bulldozer
Special Vehicle Series
Assembly Instructions
Bulldozer