Canon Creative Park Kissing Dolls User manual

Assemble the box mechanism
Glue tab
Scissors line
Parts name
Parts No.
Attach to strengthen
the part you cut.
Do not attach the
glue tabs on the bottom.
Kissing Dolls : Assembly Instructions Page
<Caution>
Keep scissors and glue away from small children.
Be careful not to cut your fingers when using scissors.
marks a basic assembly technique that remains the same
regardless of the part.
Instructions are printed only for the first instance.
The Assembly instructions are divided into three blocks: A (box
mechanism) ,B (kissing dolls' bodies) and C (kissing dolls' heads).
Follow the instructions for each block to assemble your kissing
dolls.
Use pattern: Page2 to Page7.
Cut along the line marked .
Cut out A1 by cutting along the lines.
Make a mountain fold on A1.
Trace along the mountain fold line with a pencil,
scoring it to make it easier to fold.
Cut out the hole in A3, and attach A4. In the same way,
attach A5 and A6.
Using the photo as a guide, attach in the direction of the arrow.
A1 Box
Scissors
Paste, or woodwork glue
Stencil pen, or bodkin
Ruler
Scissors line
Mountain fold
Valley fold
Glue spot
Parts No.
Notation Key
Tools
Attach A1, A2, A3 and A5 together, but do not glue the
glue tabs on the bottom yet.
Glue the back

Attach to the green area.
Do not attach the
glue tabs on the
bottom.
Align the shapes
of the glue tabs
here.
Fold in half and glue together.
Make it round
again, and glue
together.
Check that both the
inside and outside
are correct.
Attach together so
that the shafts are parallel.
Attach together so that
the shafts are parallel.
Poke the tip of A16 out through the top of the box. Poke the tip of A15 out through the top of the box.
Widen the box and
feed through the hole.
Match the colors
of these parts.
Face these parts
inwards.
Kissing Dolls : Assembly Instructions Page
Attach A7 and A8 to the box.
Assemble A9 to A14.
Assemble A15 and A16.
Insert A9 through A15 and A16, and assemble A10 ~ A13.
Insert A9 through the box, and assemble A14.
Attach the parts for the bottom of the box.
Assemble A17 and A18, cut out the hole on A19, and attach
A20 and A21. Then, attach A17 and A18 to that.

Make the kissing dolls' bodies
Use pattern: Page8 / Page9.
Insert A15 into A17,
and A16 into A18.
Align the shapes
of the glue tabs.
Attach the glue tabs
together according
to their shape.
Insert the arms
inside, and align
the shapes of the
glue tabs.
Triangular glue tab
Page
Kissing Dolls : Assembly Instructions
Attach A19 to the box, and the box mechanism is complete.
Attach B1 to A17. Then, attach B2 and B3 to that.
Using the photo as a guide, move your fingers in the direction of the
arrow, adjusting the pressure to curl the paper.
Attach the triangular glue tabs so that the front side becomes convex.
Attach B4 to A17, and attach B5 to that.
Next, assemble B4 and B5.
Assemble B6 and B7, and attach them together. In the same
way, assemble B8 and B9. Next, attach B6 and B8 to B4.
Assemble B10 and B11, and attach them to B4.
In the same way, assemble the body parts B12 ~ B22.

Attach the triangular
glue tabs so that the
front side becomes convex.
C3 Head
Align the shapes of the glue tabs,
and glue it precisely in place.
Align the shapes
of the glue tabs.
If you have problems,
adjust the angle here.
Align the shapes of the glue tabs,
and glue it precisely in place.
Slowly rotate with your finger.
Close the open parts of C2
and glue together.
Fold up the piece to roll it tightly,
as shown in the photo.
Put glue on the blue area
and attach together.
Put glue on the
blue area and
attach together.
Page
Kissing Dolls : Assembly Instructions
Make the kissing dolls' heads
To prevent the heads from overbalancing, use only
a thin layer of glue when assembling.
Attach parts C1 ~ C4.
Use pattern: Page10 / Page11.
Attach C5 to C6, and attach that to the head.
In the same way, assemble the parts C7 ~ C13.
Next, attach C14 to the head.
Fold up the piece
to roll it tightly,
as shown in
the photo.
Place the dolls' heads on their bodies, and your kissing dolls are complete!