Canon PAPER CRAFT Pop-up Card Birdcage User manual

Cut out the parts and crease them along the fold lines indicated.
Roof (vertical bars)
Roof (horizontal bars)
Horizontal bars
Vertical bars
Decorations
Floor
Support A
Supports B Supports C Support D Support E
Bird Ribbon Held in bird’s beak
Horizontal bars (door)
Doors(horizontal bars)
Doors(vertical bars)
Pop-up Card (Birdcage) : Assembly Instructions
Canon is a registered trademark of Canon Inc.
1
Caution:Glue, scissors, and other tools may be dangerous to young
children so be sure to keep them out of the reach of young children.
Valley fold
(dashed and dotted line)
*Make a valley fold.
Scissors line(solid line)
*Cut along the line.
Cut in line(solid line)
*Make a cut.
Black triangle
Glue here
Mountain fold(dotted line)
*Make a mountain fold.
Assembly Instructions
scissors, paste, a used ballpoint pen (tracing along the fold lines
makes them easier to fold)
You will needYou will need
White triangle
Glue the back

Attach the horizontal bars to the vertical roof bars, then join these
sections up to form an hexagonal cone, as shown in the photograph.
Glue one streamer onto the ribbon from the back, and attach the other
by fitting it into the cutaway and then gluing it from the back.
Stick the ribbon onto the roof section by gluing it at the glue spot.
* Fold the roof section to make the ribbon easier to stick on.
Stick on the vertical bars (door) matched up with the glue spots in
assembly Step 3 and join up both ends of the bars to form
a tubular shape.
Stick the horizontal bars onto to the glue spots on the vertical bars.
Stick decorative panels to bottom of vertical bars.
(Be careful to apply glue to the correct positions on the panels.)
2
Pop-up Card (Birdcage) : Assembly Instructions
Canon is a registered trademark of Canon Inc.

3
Fold the ends of the sections circled in red along the fold lines,
and then glue at the back. Match up the pairs and then stick them
together at the back.
Fold support A along the center line and glue together on the inside.
Attach the wings to the bird.
Match up the horizontal bars of the cage door and stick them together.
* Be careful not to get front and back mixed up.
Line up the bird with the doors that have wing-shaped glue spots on
them, and then stick on the bird.
Glue the rear sides of the bird together so that they hold the support A
in place at the glue spots. * You will be putting flowers, etc., into the
bird’s beak later in the assembly, so avoid putting any glue near there
at this stage.
Pop-up Card (Birdcage) : Assembly Instructions
Canon is a registered trademark of Canon Inc.

4
Fold support D along the center line and glue together on the inside.
Stick support D and assembly Step 13 together at their glue spots.
Stick supports C and supports B together at their glue spots.
Fold supports B along the center line and glue together on the inside.
Fold supports C along the fold lines and stick them at the back to form
sticks.
Insert support D from assembly Step 15 through the birdcage door and
glue the assembly onto the birdcage at the spots circled in red.
Glue support D onto the points circled in blue, where the vertical and
horizontal bars intersect.
Pop-up Card (Birdcage) : Assembly Instructions
Canon is a registered trademark of Canon Inc.

5
Insert the floor from the bottom of the birdcage. First glue one end
of the floor (shown in dotted lines), then stick on support B in the
center, and finally glue the other end of the birdcage to the floor.
* Fold the birdcage to make the floor easier to stick on.
Insert support B, now attached to the roof, from the top of the birdcage
so that the assembly straddles support A, then glue the roof onto the
birdcage bars at the glue spots indicated.* Fold the birdcage to
make the roof easier to stick on.
Attach assembly Step 19 to the hexagonal roof at the glue spots
indicated.
Paste together the two sides of whatever the bird is to hold in its beak
(the photograph shows a flower).
Paste the object into the bird’s beak.
Pop-up Card (Birdcage) : Assembly Instructions
Canon is a registered trademark of Canon Inc.

6
Stick the two sides of the backing sheet together.
Stick support E onto the glue spot in the center of the backing sheet.
Fold support E along the center line and glue together on the inside.
(Be careful not to stick the glue tabs together.)
Stick on a colored paper cover onto half of the rear side of the base
paper. Be careful to stick in on in the right direction.
Assembly Step 29 is the completed card when the cover is stuck on to
the other half side.
Fold the birdcage and stick the birdcage glue spot onto the backing
sheet glue spot. Then, stick on the center of the birdcage floor so that
it enfolds support E. Finally, folding the backing sheet in the center,
glue the rest of the birdcage glue spots to the corresponding glue spots
on the backing sheet.
Pop-up Card (Birdcage) : Assembly Instructions
Canon is a registered trademark of Canon Inc.