Caraudio-Systems c.LOGiC C1-PHAETON User manual

c.LOGiC® AV-Interface
C1-PHAETON
For VW Phaeton, Bentley Continental Group
with ZAB Navigation

Version 16.02.2010
Seite2
Contents
1. Prior to installation
1.1. Delivery contents
1.2. Checking the compatibility of vehicle and accessories
2. Installation
2.1. Place of installation
2.2. Activation of the interface
3. Device control
3.1. Device assignment
3.2. Compatible device list
3.3. Selection of the devices to be controlled
3.4. Key configuration
3.5. Pictures settings for the Interface
4. Specifications
5. Technical support
Information
Changes of the vehicle software can cause malfunctions of the interface. We offer free
software-updates for interfaces for one year after purchase. To receive a free update, the
interface must be sent in at own cost. Labor cost for and other expenses involved with the
software-updates will not be refunded.
Product features
Connection of a external AV-input
Controlable with the original keys of the navigation

Version 16.02.2010
Seite3
Requirements
Vehicle VW Phaeton, Bentley Continental Group
Navigation ZAB
1. Prior to installation
Read the manual prior to installation.
Technical knowledge is necessary for installation. The place of installation must be free of
moisture and away from heat sources.
1.1. Delivery contents
1.2. Checking the compatibility of vehicle and accessories
2. Installation
Switch off ignition and disconnect the vehicle’s battery! The interface needs a permanent
12V source. If power source is not taken directly from the battery, the connection has to
be checked for being start-up proven and permanent.
HW ________ SW ________
Take down the SW-version and HW-version of the interface and store this manual
for support purposes.

Version 16.02.2010
Seite4
2.1. Place of installation
Carefully remove the decorational covers of the
navigation system. Loosen the 5 TORX screws as
marked in the picture on the right and extract the
device from the center console.
Disconnect the 32pin connector from the navigation system.
Connection assignment for the 32pin connector: Connect the pink wire
of the “Audio/Video” cable kit to Pin 23 and the green wire to Pin 24.
Connect the red wire (Audio Signal right) to Pin 10 and the black wire
(Audio Ground right) to Pin 26 (both wires are paired together).
Connect the yellow wire (Audio Signal left) to Pin 11 and the black wire
(Audio Ground left) to Pin 27 (both wires are paired together).
Connect the two black wires to Pin 8 and Pin 25.
Wire Colors/Plugs:
Connection/Assignment:
● Red:
+12V DC ( Permanent Plus )
● Black:
Ground
●Yellow:
CAN-HI
●Blue:
CAN-LOW
●● White/Black:
Output +12V (100mA)
3,5mm Mini Jack Socket:
Controls
Wire Colors/Plugs:
Connection/Assignment:
● Black:
Ground
● Black:
Ground
● Pink:
Y - Signal
●Green:
C - Signal
● Red:
AUDIO Signal Output (right)
● Black:
AUDIO Ground Output (right)
●Yellow:
AUDIO Signal Output (left)
●Black:
AUDIO Ground Output (left)

Version 16.02.2010
Seite5
Connect the yellow wire (CAN-HI) of the interface cable kit
to Pin 15 and the blue wire (CAN LOW) to Pin 31.
Connect the black wire of the interface cable kit to ground
(Power Plug Pin8) and the red wire to 12V permanent plus
(Power Plug Pin7).
The 3,5mm mini jack socket of the cable kit is used
to connect the corresponding control cable (e.g. “STA-AL25“
for DVD Alpine devices) for device controls.
The optionally available Y-Adapter “CABLE-415“
(sold separately) allows to connect the IR-receiver of the
video source parallel to the interface.
(Please refer to pages 9 and 10 for details regarding control cables.)
Use a Video / Audio cinch cable (sold separately) to connect
the video source to the three cinch sockets of the interface.
Re-attach the navigation system to the center console.
2.2. Activation of the interface:
In order to activate controls for the connected devices
the system needs to be switched to TV mode by pushing
the “AUDIO/TV“ button followed by the “TV“ button.
STA-xxxx cable kit

Version 16.02.2010
Seite6
3. Device control
3.1. Device Assignment:
Device assignment occurs in the video text level.
Pushing the Softkey button “Videotext“ activates the video
text level.
The central knob is used to enter the three-digit device
RC Code (e.g. first device > „101“, second device > „203“).
Push the central knob to save the selected RC code.
Exit the level after RC code input by using the Softkey “Back“.
3.2. Compatible device list
IR-
control
Compatible devices
IR-control-
channel
cable
RC-01
DVD-Player maXXLine DVD500U, DVDMP412U,DVDMP20(U)
STA-USB
DVD-Player Ampire DVX100, Digitaldynamic DVP-1000, 900HD
DVD-Player DVD500U
STA-UNI
RC-02
DVB-T Tuner maXXLine DVBTD50, Dietz 1491(V)
STA-D2007
RC-03
DVB-T Tuner Ampire DVB-T 100
n/v
RC-07
DVB-T Tuner DVBT-CKO, maXXLine DVBTD60, DVBTD40
STA-NL
RC-10
DVD-Player Alpine RUE-4201
STA-AL25
RC-11
DVD-Player Alpine RUE-4158
STA-SV4
DVBT-Tuner Alpine TUE-T150V
STA-AL25
RC-13
iPod Vlink maXXLine
STA-USB
RC-15
Vehicle-HUB Alpine VPA-B222R, Alpine RUE-4167 Audio
STA-AL25
RC-16
Vehicle-HUB Alpine VPA-B222R, Alpine RUE-4167 DVD
STA-AL25
RC-17
DVD-Wechsler 6-fach Necvox DVA-3206
n/v
RC-18
Analog TV-Tuner Alpine TUE-T112P
STA-AL25
RC-20
DVD-Player Boa 85700
STA-USB
RC-24
DVD-Wechsler 6-fach maXXLine DVC62, Ampire DVC62
STA-UNI
RC-27
DVD-Player Nesa DVD-2007, DVD-1002, VST VDV-101
STA-USB
RC-30
DVB-T Tuner Ampire DVBT200
STA-NL
RC-32
iPod Alpine KCE-425I
STA-UNI
RC-34
DVB-T Tuner Clarion DTX509E NEU
STA-SV43
RC-41
DVB-T Tuner NavLinkz DVBT330, ACV, maXXline DVBTD80
STA-NL
RC-43
DVB-T Tuner Ampire DVBT50
STA-NL

Version 16.02.2010
Seite7
3.3. Selection of the devices to be controlled:
Use the navigation system’s buttons to control the video source(s).
The Softkey button “Sender verfolgen“ switches between devices:
ON = Device 1 , OFF = Device 2 .
Please refer to page 10 for detailed button assignments.
In order to use the controls, level A 1-6 needs to be activated
at Softkey “A 1-6 / M 1-6“.
Video device menues are controlled via the “Settings“
level. Use the central knob to navigate “left“ / “right“
and push station button “5“ to confirm a selection.

Version 16.02.2010
Seite8
3.4. Key configuration
Button Assignment Part 1
Button Assignment Part 2
* Function of central knob in the “Settings“ level (lower right knob has no function assigned to it) .
Phaeton Navigation
Model
1
2
3
4
5
6
7
8
9
10
DVD PLAYER
ON/OFF
MENU PBC
MENU
TITLE
PLAY
STOP
TRACK -
TRACK +
↑
↓
DVB-T TUNER
ON/OFF
EPG
SETUP
INFO
ENTER
EXIT
CH -
CH +
↑
↓
I-POD®CONTROL
ON/OFF
SHUFFLE
BULB
REPEAT
ENTER
PLAY
TRACK -
TRACK +
↑
↓
ANALOG TUNER
ON/OFF
FM
ADJUST
DISPLAY
SCAN
MUTE
CH -
CH +
VOL +
VOL -
Phaeton Navigation
Model
9*
10*
Softkey Button
“Sender verfolgen“
Softkey Button
“TV / AV“
Softkey Button
“Autostore“
DVD PLAYER
→
←
SWITCH DEVICE
AV
ZOOM / DISC
DVB-T TUNER
→
←
SWITCH DEVICE
AV
SCAN
I-POD®CONTROL
→
←
SWITCH DEVICE
EJECT
-
ANALOG TUNER
CH +
CH -
SWITCH DEVICE
SCAN
SCAN

Version 16.02.2010
Seite9
4. Technical data
Working voltage range: 10.5 - 14.8 V
Stand-by current consumption: > 1 MA
Operating current consumption: 35 MA
Power input 6.8 W
Max. current consumption: approx. 200 MA
Working temperature: -30°C to +80°C
Weight: 85 g
Dimensions W x H x D: 85 x 20 x 42 mm
5. Technical Support
Caraudio-Systems Vertriebs GmbH NavLinkz GmbH
manufacturer/distribution corporate sales/tech support
Rheinhorststr. 22 Eurotec-Ring 45
D-67071 Ludwigshafen am Rhein D-47445 Moers
phone [phone]
email [email protected]