Caraudio-Systems ZL-MYGIG-V2-R User manual

Version 10.06.2013 ZL-MYGIG-V2-R
z.LiNK-Interface
ZL-MYGIG-V2-R
Audio-video-input and rear-view camera input
incl. video-in-motion
compatible with Chrysler, Dodge and Jeep
vehicles
with MYGIG navigation systems
AV-input to connect any AV-source
and a rear-view camera
to the factory navigation system
incl. video-in-motion

Version 10.06.2013 ZL-MYGIG-V2-R
Page1
Contents
1. Prior to installation
1.1. Delivery contents
1.2. Check compatibility of vehicle and accessories
1.3. Pin assignments
2. Connection schema
3. Installation
3.1. Activation of the interface as current AV-source
4. Activation of the video-in-motion function
5. Specifications
6. Technical Support
Legal Information
By law, watching moving pictures while driving is prohibited, the driver must not be
distracted. We do not accept any liability for material damage or personal injury resulting,
directly or indirectly, from installation or operation of this product. This product should only
be used while standing or to display fixed menus or rear-view-camera video when the
vehicle is moving, for example the MP3 menu for DVD upgrades.
Changes/updates of the vehicle’s software can cause malfunctions of the interface. We offer
free software-updates for our interfaces for one year after purchase. To receive a free

Version 10.06.2013 ZL-MYGIG-V2-R
Page2
update, the interface must be sent in at own cost. Labor cost for and other expenses
involved with the software-updates will not be refunded.
1. Prior to installation
Read the manual prior to installation. Technical knowledge is necessary for installation. The
place of installation must be free of moisture and away from heat sources.
1.1. Delivery contents
1.2. Check compatibility of vehicle and accessories
Take down the SW-version and HW-version of the interface boxes, and store this
manual for support purposes.
Requirements
Vehicle Chrysler 200 2011-2012, Chrysler 300 2008-2010, Chrysler Aspen
2008-2009, Chrysler Sebring 2008-2010
Dodge Avenger 2008-2012, Dodge Caliber 2009-2012, Dodge
Challenger 2008-2012, Dodge Charger 2008-2010, Dodge Dakota
2008-2012, Dodge Durango 2008, Dodge Magnum 2008
Jeep Commander 2008-2010, Jeep Compass 2009-2012, Jeep
Grand Cherokee 2008-2010, Jeep Patriot 2009-2011
Navigation MYGIG REW, RER, REN and RHW
with low-speed-B-CAN (83 kbit)
Limitations
Factory-RSE Must NOT be installed.
Factory-rear-view cam Must NOT be installed.
Video-sources Only compatible to NTSC-video-sources.
For vehicles with high-speed IHS-CAN (125 kbit) the ZL-MYGIG-R must be used!

Version 10.06.2013 ZL-MYGIG-V2-R
Page3
1.3. Pin-assignments
Pin-assignment AV-INPUT
Connection
Cable colour/connector
White 22pin MYGIG connector
Video input
RCA female yellow
Video signal
● yellow
→ pin 9
Ground
● black
→ pin 10
Audio input
RCA female red/white
Audio signal (right)
● red
→ pin 14
Audio signal (left)
●white
→ pin 13
Audio ground
● black
→ pin 01
Rear-view camera input
RCA female black
Video signal
● black (ø 0,25)
→ Pin 03
Ground
● black (ø 0,5)
→ Pin 04
Pin-assignment AV-OUTPUT (rear-seat-entertainment)
Connection
Cable colour/connector
White 22pin MYGIG connector
Video output
RCA female yellow
Video signal
● yellow
→pin 6
Ground
● black
→ pin 7
Audio output
RCA female red/white
Audio signal (right)
● red
→ pin 20
Audio signal (left)
●white
→ pin 18
Audio ground
● black
→ pin 19
Pin-assignment white 22pin connector

Version 10.06.2013 ZL-MYGIG-V2-R
Page4

Version 10.06.2013 ZL-MYGIG-V2-R
Page5
2. Connection schema

Version 10.06.2013 ZL-MYGIG-V2-R
Page6
3. Installation
Switch off ignition and disconnect the vehicle’s battery! If according to factory rules
disconnecting the battery has to be avoided, it is usually sufficient to put the vehicle in
sleep-mode. In case the sleep-mode does not show success, disconnect the battery with a
resistor lead.
Place of installation is behind the head-unit.

Version 10.06.2013 ZL-MYGIG-V2-R
Page7
Instruction for example Chrysler C300
Remove the front panel from the centre console, which is
attached to multiple clips.
Remove the 4 TORX screws and pull the device out of the
centre console.
Remove the grey female 22pin connector from the rear of
the device and connect it to harness TV-MYGIG. Connect the
grey female 22pin connector of harness TV-MYGIG to
the device.
Connect the AV-input and the AV-output to the white female
22pin connector according the pin assignment and connect the
Female RCA to the av-sources.
Note: Use the attached white female 22pin connector if the male 22pin connector of the
head-unit isn’t occupied by a white female 22pin connector.
If the male 22pin connector of the head-unit is occupied by a white female 22pin connector
connect the pins into the white female 22pin connector of the vehicle (the attached white
female connector will not be required.
There are 2 options if the pins are occupied by factory:
1. Factory-RSE is installed. This interface will not be needed (separate video-in-motion
TF-MYGIG optionally available).
2. Factory RSE isn’t installed. The pins are prepared by factory and can be removed.

Version 10.06.2013 ZL-MYGIG-V2-R
Page8
3.1. Activation of the interface as current AV-source
Press RADIO/MEDIA button and after it VES followed
by AUX IN 1 via Touch-Screen to select the interface
as current AV-source.
Note: The interface switches automatically to an installed rear-view camera when reverse
gear is engaged.
4. Activation of the video-in-motion function
The video-in-motion can be activated and deactivated by Dip 1 or alternatively by the
included loose green cable in connection with a switch (not included in delivery).
With dip1 to ON the video-in-motion function is activated permanently
without disturbing the navigation performance.
With dip1 to OFF the included green cable is used to activate the
video-in-motion function.
Connect a switch to the green cable and connect the green cable to +12V ACC.
●+12V = TV-Free is activated
●0V = TV-Free is not activated
Note: The loose white cable is not required and must be isolated.
Video-in-motion permanent Dip 1 ON, Dip 2 OFF, Dip 3 OFF
Video-in-motion selective Dip 1 OFF, Dip 2 OFF, Dip 3 OFF

Version 10.06.2013 ZL-MYGIG-V2-R
Page9
5. Specifications
Operation voltage 10.5 –14.8V DC
Stand-by power drain >1mA
Operation power drain ~60mA
Power consumption ~0,72W
Temperature range -30°C to +80°C
Weight 44g
Measurements (box only) B x H x T 70 x 20 x 47 mm
6. Technical Support
Caraudio-Systems Vertriebs GmbH
manufacturer/distribution
In den Fuchslöchern 3
D-67240 Bobenheim-Roxheim
email [email protected]
Legal disclaimer: Mentioned company and trademarks, as well as product names/codes are registered
trademarks ® of their corresponding legal owners.