Cardo Systems scalarider q1 User manual

T his Quick Guide is not a substitute to the user manual and addresses only
a limited scope of features and functions of your scala rider Q1.
This reference guide may be useful to look up some basic functions and
commands while you are on the road and have no access to the user manual.
This Quick Guide can be printed and folded for easy reference, or it may be
viewed directly on your smartphone.
Intercom
Button
(“IC”)
Music / Mobile
Button (“MM”)
Volume Up
(“V+”)
Volume Down
(“V-”)
1
| GENERAL FUNCTIONS
Power ON / OFF
Press “IC” for 2 seconds
ON: 3 BLUE ashes + Ascending tone
OFF: 3 RED ashes + Descending tone
Volume Tap
“V+” or “V-” to adjust volume of current
audio source
Mute Tap “V+” and “V-” simultaneously
Battery level indicator
In Standby, press “V+” for 2 seconds
• Blue LED = Full charge
• Purple LED = Half charge
• Red LED = Almost empty
Enable / Disable VOX
(For Intercom calls only)
In standby, press “V+” and “V-” simultaneously
for 2 seconds
ENABLED: Blue ash for 2 seconds
DISABLED: Red ash for 2 seconds
A2DP audio / Intercom
priority Via the Voice Menu or the Cardo Community
Enable/Disable
Click-to-Link® (CTL)
(Enabled by default)
Via the Voice Menu or the Cardo Community
Enable/Disable Spoken
Status Announcements
(Enabled by default)
Via the Voice Menu or the Cardo Community
2
| VOICE MENU
Enter Voice Menu
In standby, press “MM” and “IC”
simultaneously for 5 seconds. Follow the
audio instructions.
Exit Voice Menu Press “MM” for 2 seconds
3
| LED STATUS
None scala rider is OFF
1 BLUE ash every
3 seconds
Standby mode
No active audio sources
2 BLUE ashes every
3 seconds
Active mode – Call in progress / music or
other audio source is ON
1 RED ash every
3 seconds Standby mode – Battery is low
2 RED ashes every
3 seconds Active mode – Battery is low
Solid RED Charging
4
| MOBILE PHONE
Answer a call Tap
“MM” or speak any word loudly to
answer by VOX
Reject a call Remain silent for 15 seconds, or press and
hold “MM” for 2 seconds
End a call Tap “MM”
Voice Dial*
(if supported by mobile
phone)
Tap “MM” and “IC” simultaneously and
follow the prompt from the mobile
Redial* Press “MM” and “IC” for 2 seconds
Hot Dial* Tap “MM” 3 times
Set default phone When on a phone call, press
“V+” for
5 seconds
Toggle default phone In Standby, press “ MM ” for 5 seconds
*This feature is not available during mobile calls
5
| A2DP MUSIC AND FM RADIO
Turn on A2DP Music In Standby, tap “MM”
Turn on Radio In Standby, double tap “MM”
Pause / Stop Audio Press “MM” for 2 seconds
Next Track / Station With audio ON, tap “MM”
Previous Track /Station* With audio ON, double tap “MM”
Music Sharing (via A2DP only)
[SENDER] Start/Stop
sharing your music
During A2DP music playback, press “V+” or
“V-” for 2 seconds
[RECEIVER] Stop music
sharing Press “V+” or “V-” for 2 seconds
*With some phones you may need to repeat this action
6
| PAIRING BLUETOOTH DEVICES: MOBILE PHONE/
GPS/A2DP MUSIC PLAYER
Bluetooth Channel 1
pairing mode In Standby, press “V+” for 5 seconds
Bluetooth Channel 2
pairing mode In Standby, press “V-” for 5 seconds
communication in motion®
Q1 / Q1 TeamSet™

7
| INTERCOM
Note: TeamSet units are already factory paired!
Pairing
Your Q1 unit has an Intercom channel for communication between rider
and passenger.
In Standby, press “IC” for 5 sec. on both units until LEDs begin ashing
rapidly. After a few seconds, the LED will ash RED for 2 seconds,
indicating that the unit is paired and ready to use.
Calling
Start Intercom call Tap “IC”
End Intercom call Tap “IC”
Voice Connect (VOX)
Speak any word loudly into the microphone to activate the VOX. An
intercom call will start automatically.
8
| CLICK TO LINK® “CTL” CALLS
Send a “CTL” call request
(search lasts up to
10 seconds)
In standby, press “MM” for 2 seconds
End a “CTL” call /
Cancel “CTL” request Tap “IC”
Accept a “CTL” call
When hearing the CTL ringtone:
Tap “IC” or say any word loudly to answer
by VOX
Reject a “CTL” call Remain silent until the CTL ringtone stops or
press “IC” for 2 seconds
Enable/Disable “CTL”
(Enabled by default) Via the Voice Menu or the Cardo Community
9
| RADIO STATION TUNING
Seek up/down and Save
Choose a preset by tapping “MM”
Press “V+” or “V-” for 2 seconds
Tap “MM” within 20 seconds to save to
current preset
Scan: Automatically
scans up for a station
With Radio ON, press “V+” for 5 seconds
To stop search, tap “V+” or “V-”
Tap “MM” within 20 seconds to save to
current preset
Automatic Radio Tuning:
Save 6 Temporary
Stations
With Radio ON, press “V-” for 5 seconds
Enable / Disable RDS With Radio ON, press “V+” and “V-”
simultaneously for 2 seconds
MAN01001 – for Q1-Q1 TeamSet_003A2
10
| CARDO COMMUNITY® PLATFORM
Visit http://community.cardosystems.com to:
• Register your device for warranty and technical support
• Download and install the latest software upgrades
• Customize settings
11
| TROUBLESHOOTING
Reboot
If your scala rider stops responding reset it by
turning it o and then on again (press “IC” for
2 seconds).
Reset Pairing
(Deletes all
paired devices)
1. In Standby, press “V+” for 5 seconds until LED
ashes RED/BLUE.
2. Press “MM” for 2 seconds until LED ashes
5 times in PURPLE and unit turns o.
The contents of this Quick Guide, including all text, illustrations and drawings are
the exclusive intellectual property of Cardo Systems, Inc. (the “Company”) and are
protected by copyright laws. Any partial or total reproduction, translation and or
dissemination, without the prior written authorization by the Company are strictly
prohibited. Any rights not expressly granted herein are reserved.
Intercom
Button
(“IC”)
Music / Mobile
Button (“MM”)
Volume Up
(“V+”)
Volume Down
(“V-”)