Carrier 38CKC Operation manual

Copyright 2001 Carrier Corporation Form 38CKC-5PD
Product
Data
38CKC
60 Hz Air Conditioner
Sizes 018 thru 060
Model 38CKC Energy-Efficient Air
Conditioner incorporates innovative
technology to provide reliable summer
cooling performance. Built into these
units are the features most desired by
homeowners today, including SEER
ratings of up to 10.5 when used
with components designated by
manufacturer.All models are listed
with UL, c-UL, ARI, CEC, and
CSA-EEV.
AVAILABLE OPTIONS
Electrical Range — All units are
offered in 208–230v single phase.
Three-phase units are available from
030 through 060 sizes in 208/230v and
from 036 through 060 sizes in 460v.
Wide Range of Sizes — The 38CKC
is available in 8 nominal sizes from
018 through 060 to meet the needs of
residential and light commercial
applications.
WeatherArmor II Cabinet — The
steel is protected with a galvanized
coating and treated with a layer of zinc
phosphate. A modified polyester
powder coating is then applied and
baked on, providing each unit with a
hard, smooth finish that will last for
many years.
All screws on cabinet exterior are
coatedforalong-lasting,rust-resistant,
quality appearance.
Totally Enclosed Fan Motor —
Provides greater reliability under
adverse conditions and dependable
performance for many years. The
permanent-split-capacitor-type motor
was designed for optimum efficiency.
The motor was then qualified under
extreme conditions to help ensure a
long, reliable life.

2
UnitDesign —Coppertube,enhanced
sine wave aluminum fin coil is
designed for optimum heat transfer.
Verticalairdischargecarriessoundand
hot condenser air up and away from
adjacent patio areas and foliage. Heat
pump style drain pan allows for easy
removal of water, dirt, and leaves.
Application Versatility — The unit
canbe combined witha wide varietyof
evaporator coils and blower packages
to provide quiet, dependable comfort.
Unit can be installed on a roof or at
ground level.
External Service Valves — Service
valves are brass, front seating type. The
38CKC has sweat field connections.
Valves are externally located so
refrigeranttubeconnectionscanbemade
quickly and easily. Each valve has a
service port for ease of checking
operating refrigerant pressures.
Easy Serviceability — One panel
provides access to electrical controls
and compressor. Removal of wire
dome gives access to fan motor and
removal of the top gives access to the
coil.
Compressor Protection — Each
compressor is protected with internal
temperature- and current-sensitive
overloads.
LimitedWarranty — Standard 1-year
warranty on parts, with a limited
5-year warranty on compressor parts.
M
A
N
U
F
A
C
T
U
R
E
R
C
E
R
T
I
F
I
E
D
T
O
A
R
I
A
S
C
O
M
P
L
Y
I
N
G
W
I
T
H
A
R
I
S
T
A
N
D
A
R
D
2
1
0
U
N
I
T
A
R
Y
A
I
R
C
O
N
D
I
T
I
O
N
I
N
G
E
Q
U
I
P
M
E
N
T
REGISTERED QUALITY SYSTEM
CERTIFICATION APPLIES ONLY
WHEN THE COMPLETE SYSTEM
IS LISTED WITH ARI.
M
o
d
e
l
num
b
er nomenc
l
a
t
ure
The data in this publication is displayed for all series; however, every series may not be available from manufacturer.
38CKC 018 3 0 1
Electric Air Conditioner Packaging
Nominal Capacity
018 — 18,000 Btuh 042 — 42,000 Btuh
024 — 24,000 Btuh 048 — 48,000 Btuh
030 — 30,000 Btuh 060 — 60,000 Btuh
036 — 36,000 Btuh
Series
Electrical
3 — 208-230-1
5 — 208/230-3
6 — 460-3

3
Physical data
* For tubing sets between 50 and 175 ft, consult Residential Split Systems Long-Line Application Guideline.
NOTE: See unit Installation Instructions for proper installation.
METERING DEVICE
* Piston listed is for any approved non-capillary tube coil combination.
Piston is shipped with outdoor unit and must be installed in an
approved indoor coil.
SOUND POWER (dBA)
(A-wtd. without pure tone penalty)
UNIT SIZE 018-34 024-34 030-50/34 036-54/
61/35 042-34, 54/61 047-30, 50, 60 048-36, 56, 66 060-37, 57, 67
OPERATINGWT (Lb)
115 117 124/122 129/138/138 138/142 177 192 231
COMPRESSOR
Manufacturer &Type
Bristol Recip Bristol Recip Copeland
Recip/
Bristol Recip
Millennium Scroll/
Copeland Recip/
Bristol Recip
Scroll Tech/
Copeland
Recip
Scroll Tech Scroll Tech Scroll Tech
REFRIGERANT
Control
Charge (Lb) @ 15 Ft
R22
AccuRater® (Bypass Type)
3.30 3.65 4.19/4.25 4.63/5.00/4.60 5.00/5.13 6.13 6.13 8.31
COND FAN
Air Discharge
Air Qty (CFM)
Motor HP
Motor RPM
Propeller Type, Direct Drive
Vertical
1500 1600 2000 2500 2500 2500 2500 3400
1/8 1/6 1/10 1/4 1/4 1/4 1/4 1/4
1500 1500 1100
1100
1100 1100 1100 1100
COND COIL
Face Area (Sq Ft)
Fins per In.
Rows
Circuits
Copper Tube, Aluminum Plate Fin
6.18 6.8 7.4 9.1/9.1/8.3 9.9/10.7 10.76 10.7 18.5
20 22 20 20/25/25 22/25 25 25 25
111 1 1111
112 2 3334
VALVE CONNECTION (In. ID)
Vapor
Liquid
Sweat
5/8 5/8 3/4 3/4 7/8 7/8 7/8 7/8
3/8
REFRIGTUBES* (In. OD)
Vapor (0–50 FtTube Length)
5/8 5/8 3/4 3/4 7/8 7/8 7/8 1-1/8
Vapor (Max Diameter for
Long-Line Applications)
3/4 3/4 7/8 7/8 1-1/8 3/4 1-1/8 1-1/8
Liquid (0–50 FtTube Length)
3/8
Liquid (For Long-Line
Applications)
3/8
UNIT SIZE
AND SERIES PISTON IDENTIFICATION NO.
018-34 52
024-34 59
030-34 65
030-50 67
036-35, 54 73
036-61 70
042-34, 54 78
042-61 82
047-30, 50, 60 80
048-36, 56, 66 80
060-37, 57, 67 93
UNIT
SIZE SOUND LEVEL (dBA) OCTAVE BAND CENTER FREQUENCY (Hz)
125 250 500 1000 2000 4000 8000
018-34 80 58.0 64.0 68.5 72.5 71.5 68.0 60.0
024-34 80 59.5 65.5 70.0 74.0 71.0 69.5 60.5
030-34 80 55.0 64.5 71.0 72.0 70.5 69.0 62.5
030-50 80 55.0 62.5 73.5 74.0 71.0 67.5 59.5
036-54 82 57.0 64.5 73.0 74.0 72.0 73.0 65.5
036-61 82 55.0 64.0 73.0 74.5 72.0 68.5 64.0
036-35 82 55.5 66.5 70.5 74.5 73.5 70.0 63.5
042-34, 54 82 54.5 67.0 69.0 73.0 72.5 71.5 63.0
042-61 82 59.0 66.5 68.5 75.5 71.5 73.0 65.5
047-30, 50, 60 82 58.5 65.0 69.0 76.0 73.5 71.0 63.0
048-36, 56, 66 82 56.5 69.0 67.5 73.0 72.5 72.5 64.0
060-37, 57, 67 82 58.0 67.5 72.0 76.0 76.0 73.0 67.0

4
Accessories
See notes on page 5.
PART NO. DESCRIPTION
KAATD0101TDR
Time-Delay Relay — All Sizes
KSALA0201R22 Low Ambient Kit — All Sizes
32LT660004 (RCD)* MotorMaster® Control — Sizes 030–060 230v
32LT660005 (RCD)* MotorMaster® Control — Sizes 036–060 460v
N/A MotorMaster® Control — Sizes 018, 024
HC34GE232 (RCD) Ball Bearing Fan Motor — Size 030 230v
HC40GE232(RCD)* Ball Bearing Fan Motor — Sizes 036–060 230v
HC40GE462 (RCD) Ball Bearing Fan Motor — Sizes 036–060 460v
N/A Ball Bearing Fan Motor — Sizes 018, 024
KAAFT0101AAA Evaporator Freeze Thermostat — All Sizes
KAAWS0101AAA Winter Start Control — All Sizes
KSACG0105CMC Inlet Grille Kit — Size 018
KSACG0205CMC Inlet Grille Kit — Size 024
KSACG0604CSM Inlet Grille Kit — Sizes 030 (34, 50)
KSACG0704CSM Inlet Grille Kit — Size 036 (35)
KSACG0804CSM Inlet Grille Kit — Sizes 036 (54, 61)
KSACG0904CSM Inlet Grille Kit — Size 042 (34, 54)
KSACG1004CSM Inlet Grille Kit — Sizes 042 (61), 047 (30, 50, 60), 048 (36, 56, 66)
KSACG2004CMD Inlet Grille Kit — Sizes 060 (37, 57, 67)
KSACY0101AAA Cycle Protector — All Sizes
KSAHS2001AAA Start Assist — Capacitor and Relay — Sizes 018, 024
KSAHS0901AAA Start Assist — Capacitor and Relay — Sizes 030 (34)
KSAHS1901AAA Start Assist — Capacitor and Relay — Size 036 (35)
KSAHS1501AAA Start Assist — Capacitor and Relay — Size 042 (34)
KSAHS1601AAA Start Assist — Capacitor and Relay — Sizes 048 (36); 060 (37)
N/A Start Assist — Capacitor and Relay — All 3 Phase
KAACS0201PTC Start Assist — PTC — All 1 Phase
N/A Start Assist — PTC — All 3 Phase
KAACH1001AAA Crankcase Heater — Sizes 018–030;036 (35)
KAACH1101AAA Crankcase Heater — Sizes 036 (61), 042 (61)
KAACH1201AAA Crankcase Heater — Sizes 036 (54);042 (34, 54); 048 (36, 56);060 (37, 57)
KAACH1301AAA Crankcase Heater — Sizes 048 (67);060 (67)
KSASH1201COP Sound Hood — Sizes 036 (61);042 (61)
KSASH1901CYL Sound Hood — Sizes 036 (54);042 (34, 54)
KSASH2001BRL Sound Hood — Sizes 036 (35)
KSASH2001CYL Sound Hood — Sizes 047 (30, 50, 60), 048 (36, 56, 66), 060 (37, 57, 67)
N/A Sound Hood — Sizes 018–030
KAATX0201RPB Thermostatic Expansion Valve (RPB) — Size 018
KAATX0301RPB Thermostatic Expansion Valve (RPB) — Size 024
KAATX0401RPB Thermostatic Expansion Valve (RPB) — Size 030
KAATX0501RPB Thermostatic Expansion Valve (RPB) — Sizes 036, 042
KAATX0601RPB Thermostatic Expansion Valve (RPB) — Sizes 047, 048
KAATX0701RPB Thermostatic Expansion Valve (RPB) — Size 060
KSATX0601HSO Thermostatic Expansion Valve (Hard Shutoff) — Sizes 018–042
KSATX0701HSO Thermostatic Expansion Valve (Hard Shutoff) — Sizes 047–060
KAALP0101LPS Low-Pressure Switch — All Sizes
KSAHI0101HPS High-Pressure Switch — All Sizes
P502-8083S (RCD) Filter Drier — Sizes 018–036
P502-8163S (RCD) Filter Drier — Sizes 042–060
KAALS0101LLS† Liquid-Line Solenoid Valve — All Sizes
KAACF0701SML Coastal Filter — Sizes 018, 024
KAACF1001MED Coastal Filter — Sizes 030–048
KAACF1101LRG Coastal Filter — Size 060

5
*Fan motor with ball bearings required.
† Start assist capacitor and relay required when using liquid solenoid valve or hard shutoffTXV (except 036 and 042, Series 30;048, 060 Series 30,
31 single phase; and all 3-phase units). Do not use hard shutoffTXV with liquid solenoid valve.
N/A — Not Applicable
Accessory usage guideline
* For tubing line sets between 50 and 175 ft, refer to Residential’s Split Systems Long-Line Application Guideline.
† Only when low-pressure switch is used.
‡ Required for Low-Ambient Controller (full modulation feature) and MotorMaster® Control only.
Accessory description and usage (Listed alphabetically)
1. Ball Bearing Fan Motor
A fan motor with ball bearings which permits speed reduction while maintaining bearing lubrication.
SUGGESTED USE: Required on all units where Low-Ambient Controller (full modulation feature) or MotorMaster® Control has been added.
2. Coastal Filter
A mesh screen inserted under the top cover and inside the base pan to protect the condenser coil from salt damage without restricting airflow.
SUGGESTED USE: In geographic areas where salt damage could occur.
3. Compressor Start Assist — Capacitor and Relay
Start capacitor and start relay gives ‘‘hard’’ boost to compressor motor at each start-up.
SUGGESTED USE: Installations where interconnecting tube length exceeds 50 ft.
Installations where outdoor design temperature exceeds 105°F (40.6°C).
Replacement installations with hard shutoff expansion valve on indoor coil.
Installations where Liquid-Line Solenoid Valve has been added.
4. Compressor Start Assist — PTC
Solid-state electrical device which gives a ‘‘soft’’ boost to the compressor at each start-up.
SUGGESTED USE: Installations with marginal power supply.
Replacement installations with rapid pressure balance (RPB) expansion valve on indoor coil.
5. Crankcase Heater
An electric resistance heater which mounts to the base of the compressor to keep the lubricant warm during off cycles. Improves compressor lubrication on
restart and minimizes chance of refrigerant slugging. May or may not include a thermostat control.
SUGGESTED USE: When interconnecting tube length exceeds 50 ft.
When unit will be operated below 55°F (12.8°C) outdoor air temperature. (Use with low-ambient controller.)
All commercial installations.
THERMOSTAT PKG. DESCRIPTION
TSTATCCNAC01-B
Thermostat, Auto Changeover, Non-Programmable, °F/°C, 1-Stage Heat, 1-Stage Cool
TSTATCCPAC01-B Thermostat, Auto Changeover, 7-Day Programmable, °F/°C, 1-Stage Heat, 1-Stage Cool
TSTATCCBAC01-B Builder’sThermostat, Manual Changeover, Non-Programmable, °F/°C, 1-Stage Heat, 1-Stage Cool
TSTATCCSEN01-B Outdoor Air Temperature Sensor
TSTATXXNBP01 Backplate for Non-Programmable Thermostat
TSTATXXPBP01 Backplate for Programmable Thermostat
TSTATXXBBP01 Backplate for Builder’s Thermostat
TSTATXXCNV10 Thermostat Conversion Kit (4 to 5 wire) — 10 Pack
ACCESSORY
REQUIRED FOR
LOW-AMBIENT
APPLICATIONS
(Below 55°F)
REQUIRED FOR
LONG-LINE
APPLICATIONS*
(Over 50 Ft)
REQUIRED FOR
SEA COAST
APPLICATIONS
(Within 2 Miles)
Crankcase Heater Yes Yes No
Evaporator FreezeThermostat Yes No No
Winter Start Control Yes† No No
Accumulator No No No
Compressor Start Assist
Capacitor and Relay Yes Yes No
MotorMaster® Control
or
Low-Ambient Pressure Switch Yes No No
Wind Baffle See low-ambient instructions No No
Coastal Filter No No Yes
Unit Risers Recommended No Recommended
Liquid-Line SolenoidValve
or
Hard ShutoffTXV No
See
Long-Line
Application Guideline No
Ball Bearing Fan Motor Yes‡ No No

6
Accessory description and usage continued
6. Cycle Protector
Solid-state timing device which prevents compressor rapid recycling. Control provides an approximate 5-minute delay after power to the compressor has been
interrupted for any reason, including normal room thermostat cycling.
SUGGESTED USE: Installations in areas where power interruptions are frequent.
Where user is likely to ‘‘play’’ with the room thermostat.
All commercial installations.
Installations where interconnecting tube length exceeds 50 ft.
High-rise applications.
7. Evaporator FreezeThermostat
An SPST temperature actuated switch which stops unit operation when evaporator reaches freeze-up conditions.
SUGGESTED USE: All units where Winter Start Control has been added.
8. Filter Drier
A device for removing contaminants from refrigerant circulating in an air conditioner: 1-direction flow.
SUGGESTED USE: All split-system air conditioners.
9. High-Pressure Switch
Auto reset SPST switch activated by refrigerant pressure on high side of refrigerant circuit. Cycles compressor off if refrigerant pressure rises to 400 ± 10 psig
and resets at 298 ± 20 psig. Provides protection against compressor damage due to loss of outdoor airflow. To prevent rapid compressor recycling, Cycle
Protector can be used with this switch.
SUGGESTED USE: Installations exposed to very ‘‘dirty’’ outdoor air.
Installations where condenser inlet air temperature exceeds 125°F (51.7°C).
10. Inlet Grille Kit
A field-installed enhanced inlet grille to replace the standard inlet grille on residential air conditioners and heat pumps.
SUGGESTED USE: For greater protection against inclement weather, incidental damage, and vandalism.
11. Liquid-Line SolenoidValve (LSV)
An electrically operated shutoff valve to be installed at the outdoor or indoor unit (depending on tubing configuration) which stops and starts refrigerant liquid
flow in response to compressor operation. Maintains a column of refrigerant liquid ready for action at next compressor operation cycle.
NOTE: Compressor Start Assist–Capacitor and Relay must also be used. Do not use with hard shutoff TXV.
SUGGESTED USE: For improved system performance in air conditioners for certain combinations of indoor and outdoor units. Refer to ARI Unitary Directory.
In certain long-line applications. Refer to Long-Line Application Guideline.
12. Low-Pressure Switch
Auto reset SPST switch activated by refrigerant pressure on low side of refrigerant circuit. Cycles compressor off if refrigerant pressure drops to about 27
psig. Prevents indoor coil freeze-up due to loss of indoor airflow. Provides additional protection against compressor damage due to loss of refrigerant charge.
To prevent rapid compressor recycling, Cycle Protector can be used with this switch.
SUGGESTED USE: Where indoor coil is exposed to ‘‘dirty’’ air.
All commercial installations.
13. MotorMaster® Control
A fan speed control device activated by a temperature sensor. Designed to control condenser fan motor speed in response to the saturated, condensing
temperature during operation in cooling mode only. For outdoor temperatures down to –20°F, it maintains condensing temperature at 100°F ± 10°F.
SUGGESTED USE: Cooling operation at outdoor temperatures below 55°F.
All commercial installations.
14. Outdoor AirTemperature Sensor
A device that allows the temperature at a remote location (outdoors) to be displayed at the thermostat.
SUGGESTED USE: All corporate programmable thermostats.
15. Sound Hood
Wraparound sound attenuation cover for the compressor. Reduces unit sound level by about 2 dBA.
SUGGESTED USE: Unit installed closer than 15 ft to quiet areas — bedrooms, etc.
Unit installed between 2 houses less than 10 ft apart.
16. Thermostatic ExpansionValve (TXV)
A modulating flow-control valve which meters refrigerant liquid flow rate into the evaporator in response to the superheat of the refrigerant gas leaving the
evaporator. Kit includes valve, adapter tubes, and external equalizer tube. Both hard shutoff and RPB valves are available. Do not use hard shutoff TXV with
Liquid-Line Solenoid Valve.
SUGGESTED USE: For improved system performance in cooling mode for certain combinations of indoor and outdoor units. Refer to ARI Unitary Directory.
Required for use on all zoning systems.
17. Time-Delay Relay
An SPST delay relay which briefly continues operation of the indoor blower motor to provide additional cooling after the compressor cycles off.
SUGGESTED USE: For improved efficiency ratings for certain combinations of indoor and outdoor units. Refer toARI Unitary Directory.
18. Winter Start Control
An SPST delay relay which bypasses the low-pressure switch for approximately 3 minutes to permit start-up for cooling operation under low-load conditions.
SUGGESTED USE: All air conditioners where Low-Ambient Controller has been added.

7
Electrical data
* Permissible limits of the voltage range at which unit will operate satisfactorily. Operation outside these limits may result in unit failure.
† If wire is applied at ambient greater than 30°C (86°F), consult Table 310-16 of the NEC (ANSI/NFPA 70).
The ampacity of nonmetallic-sheathed cable (NM), trade name ROMEX, shall be that of 60°C (140°F) conductors, per the NEC (ANSI/NFPA 70)
Article 336-26.If other than uncoated (non-plated), 60 or 75°C (140 or 167°F) insulation, copper wire (solid wire for 10 AWG and smaller, stranded
wire for larger than 10 AWG) is used, consult applicable tables of the NEC (ANSI/NFPA 70).
‡ Length shown is as measured 1 way along wire path between the unit and service panel for a voltage drop not to exceed 2%.
** Time-delay fuse.
FLA — Full Load Amps
LRA — Locked Rotor Amps
MCA — Minimum Circuit Amps
RLA — Rated Load Amps
NOTES: 1. Control circuit is 24v on all units and requires external power source.
2. Copper wire must be used from service disconnect to unit.
3. All motors/compressors contain internal overload protection.
UNIT
SIZE V/PH
OPERVOLTS* COMPRESSOR FAN
FLA MCA
60°C
MIN
WIRE
SIZE†
75°C
MIN
WIRE
SIZE†
60°C
MAX
LENGTH
(Ft)‡
75°C
MAX
LENGTH
(Ft)‡ MAX FUSE** OR
CKT BKR AMPS
Max Min LRA RLA
018-34
208-230-1 253 197
48.0 9.0 0.8 12.1 14 14 61 58 20
024-34 60.0 11.6 1.0 15.5 14 14 49 47 20
030-34 73.0 14.1 0.8 18.4 14 14 41 39 30
036-35 82.0 16.0 1.4 21.4 12 12 58 55 30
042-34 115.0 20.5 1.4 27.0 10 10 70 70 40
047-30 124.0 21.8 1.4 28.7 10 10 69 66 50
048-36 140.0 24.4 1.4 31.9 8 10 97 59 50
060-37 165.0 28.9 1.4 37.5 8 8 82 78 60
030-50
208/230-3 253 187
68.0 9.4 0.8 12.6 14 14 70 65 15
036-54 75.0 13.5 1.4 18.3 14 14 60 55 30
042-54 90.0 12.4 1.4 16.9 14 14 50 50 25
047-50 92.0 12.8 1.4 17.4 14 14 44 42 30
048-56 105.0 14.1 1.4 19.0 14 14 41 39 30
060-57 125.0 16.0 1.4 21.4 12 12 57 54 30
036-61
460-3 506 414
33.0 5.1 0.8 7.2 14 14 250 238 15
042-61 42.0 6.2 0.8 8.6 14 14 210 200 15
047-60 46.0 6.4 0.7 8.7 14 14 88 83 15
048-66 52.5 7.1 0.8 9.7 14 14 79 75 15
060-67 66.5 8.0 0.8 10.8 14 14 72 68 20

8
Dimensions — 38CKC
AIR DISCHARGE
AIR IN
ASQ
B
P
C
3/8 -IN. DIA
TIEDOWN
KNOCKOUTS
(2) PLACES
27/8″
11/4″
H
G
F
E
FIELD CONTROL SUPPLY CONN 7
/
8 -IN.
DIA
HOLE
FIELD POWER SUPPLY CONN 7
/
8 -IN.
DIA HOLE WITH
1
1
/
8 -IN.
DIA KNOCKOUT
AND 1 3
/
8 -IN.
DIA
KNOCKOUT
3
/
8 -IN.
DIA LIQUID
LINE CONN
D DIA VAPOR LINE CONN
L
K
J
AIR IN
M
N
AIR DISCHARGE
AIR IN AIR IN
AIR DISCHARGE
NOTES:
1. Allow 30 in. clearance to service side of unit, 48 in. above unit, 6 in. on one side, 12 in. on remaining side, and 24 in. between units for proper airflow. 2. Minimum outdoor operating ambient in cooling mode is 55°F, max. 125°F. 3. Series designation is the 13th position of the unit model number. 4. Center of gravity . A97043
DIMENSIONS (IN.)
UNIT
SIZE SERIES
UNIT DIMENSIONS MINIMUM
MOUNTING PAD
DIMENSIONSABCDEFGHJKLMNP
018 4 18 21-15/16 3-3/16 5/8 3 15 16-5/16 17-3/4 10-3/16 16-1/8 17-3/4 7-7/8 8-3/8 9-3/8 18 X 18 024 4 18 23-15/16 3-3/16 5/8 3 15 16-5/16 17-3/4 10-3/16 16-1/8 17-3/4 7-7/8 8-3/8 9-1/2 18 X 18 030 4 22-1/2 21-15/16 3-3/16 3/4 3-11/16 18-1/8 19-3/4 22-1/4 14-3/8 19-9/16 22-1/16 10-3/8 10-3/4 10-3/4 22-1/2 X 22-1/2 036 1 22-1/2 25-15/16 3-3/16 3/4 3-11/16 18-1/8 19-3/4 22-1/4 14-3/8 19-9/16 22-1/16 10-1/4 9-1/2 11-1/4 22-1/2 X 22-1/2 036 4 22-1/2 25-15/16 3-3/16 3/4 3-11/16 18-1/8 19-3/4 22-1/4 14-3/8 19-9/16 22-1/16 10-3/8 10-3/4 11-1/4 22-1/2 X 22-1/2 036 5 22-1/2 23-15/16 3-3/16 3/4 3-11/16 18-1/8 19-3/4 22-1/4 14-3/8 19-9/16 22-1/16 10-3/8 10-3/4 11 22-1/2 X 22-1/2 042 1 22-1/2 29-15/16 3-1/4 7/8 3-11/16 18-1/8 19-13/16 22-1/4 14-3/8 19-9/16 22-1/16 10-3/8 10-3/4 11-1/8 22-1/2 X 22-1/2 042 4 22-1/2 27-15/16 3-1/4 7/8 3-11/16 18-1/8 19-13/16 22-1/4 14-3/8 19-9/16 22-1/16 10-3/8 10-3/4 11-1/8 22-1/2 X 22-1/2 047 0 22-1/2 29-15/16 3-1/4 7/8 3-11/16 18-1/8 19-13/16 22-1/4 14-3/8 19-9/16 22-1/16 10-3/8 10-3/4 11-1/8 22-1/2 X 22-1/2 048 6 22-1/2 29-15/16 3-1/4 7/8 3-11/16 18-1/8 19-13/16 22-1/4 14-3/8 19-9/16 22-1/16 10-3/8 10-3/4 11-1/8 22-1/2 X 22-1/2 060 7 30 33-15/16 3-1/4 7/8 6-1/2 23-1/2 27-1/4 29-3/4 20 27-1/16 29-9/16 15-1/2 14 15 30 X 30

9
Combination ratings
UNIT
SIZE-SERIES INDOOR
MODEL TOT. CAP. BTUH
FACTORY-
SUPPLIED
ENHANCE-
MENT
SEER
EERA
Standard
Rating
Carrier Gas
Furnace or
TDR†Accessory TXV‡
018-34
CC5A/CD5AA018* 17,200 NONE —10.00 10.00 9.15
CC5A/CD5AA024 17,800 NONE —10.00 10.00 9.40
CC5A/CD5AW024 17,800 NONE —10.00 10.00 9.40
CE3AA024 17,800 NONE —10.00 10.00 9.45
CF5AA024 17,900 NONE —10.00 10.00 9.50
CK3BA024 17,800 NONE —10.00 10.00 9.55
CK5A/CK5BA018 17,200 NONE —10.00 10.00 9.35
CK5A/CK5BA024 17,800 NONE —10.00 10.00 9.55
CK5A/CK5BW024 17,800 NONE —10 10.00 9.55
F(A,B)4AN(F,C)018 17,200 TDR 10.00 —10.00 9.25
F(A,B)4AN(F,C)024 17,800 TDR 10.50 —10.50 9.60
FC4BNF024 17,800 TDR&TXV 10.50 ——9.65
FF1DNA018 17,200 TDR 10.00 —10.00 9.45
FF1DNA024 17,800 TDR 10.50 —10.50 9.50
FG3AAA024 17,800 NONE 10.00 —10.00 9.35
FK4CNF001 17,800 TDR&TXV 11.00 ——10.60
40FKA/FK4CNF002 18,000 TDR&TXV 11.50 ——10.70
COILS + 58MVP060-14VARIABLE SPEED FURNACE
CC5A/CD5AW024 17,800 TDR 10.50 —10.50 10.25
CE3AA024 17,800 TDR 10.50 —10.50 10.25
CK5A/CK5BW024 17,800 TDR 10.50 —10.50 10.40
COILS + 58MVP080-14VARIABLE SPEED FURNACE
CC5A/CD5AW024 17,800 TDR 10.50 —10.50 10.30
CE3AA024 17,800 TDR 10.50 —10.50 10.25
COILS + 58U(H,X)V060-12VARIABLE SPEED FURNACE
CC5A/CD5AA018 17,200 TDR 10.50 —10.50 9.85
CC5A/CD5AA024 17,800 TDR 10.50 —10.50 10.20
CE3AA024 17,800 TDR 10.50 —10.50 10.20
CK3BA024 17,800 TDR 10.50 —10.50 10.50
CK5A/CK5BA018 17,200 TDR 10.50 —10.50 10.20
CK5A/CK5BA024 17,800 TDR 10.50 —10.50 10.50
024-34
CC5A/CD5AA024* 23,600 NONE —10.00 10.00 9.05
CC5A/CD5AA030 23,800 NONE —10.00 10.00 9.05
CC5A/CD5AW024 23,600 NONE —10.00 10.00 9.05
CC5A/CD5AW030 23,800 NONE —10.00 10.00 9.05
CE3AA024 23,600 NONE —10.00 10.00 9.10
CE3AA030 23,800 NONE —10.00 10.00 9.20
CF5AA024 23,600 NONE —10.00 10.00 9.10
CK3BA024 23,600 NONE —10.00 10.00 9.15
CK3BA030 23,800 NONE —10.00 10.00 9.15
CK5A/CK5BA024 23,600 NONE —10.00 10.00 9.15
CK5A/CK5BA030 23,800 NONE —10.00 10.00 9.15
CK5A/CK5BW024 23,600 NONE —10.00 10.00 9.15
CK5A/CK5BW030 23,800 NONE —10.00 10.00 9.15
F(A,B)4AN(F,C)024 23,600 TDR 10.00 —10.00 9.20
F(A,B)4AN(F,C)030 23,800 TDR 10.00 —10.00 9.35
FC4BNF024 23,600 TDR&TXV 10.00 ——9.20
FC4BNF030 23,800 TDR&TXV 10.00 ——9.30
FF1DNA024 23,600 TDR 10.00 —10.00 9.05
FF1DNA030 23,800 TDR 10.00 —10.00 9.20
FG3AAA024 23,000 NONE 10.00 —10.00 8.95
FK4CNF001 24,000 TDR&TXV 11.00 ——10.05
40FKA/FK4CNF002 24,400 TDR&TXV 11.00 ——10.15
40FKA/FK4CNF003 24,400 TDR&TXV 11.00 ——10.30
COILS + 58MVP060-14VARIABLE SPEED FURNACE
CC5A/CD5AW024 23,000 TDR 10.50 —10.50 9.65
CC5A/CD5AW030 23,400 TDR 10.50 —10.50 9.80
CE3AA024 23,000 TDR 10.50 —10.50 9.70
CE3AA030 23,400 TDR 10.50 —10.50 9.85
CK3BA024 23,000 TDR 10.50 —10.50 9.75
CK3BA030 23,400 TDR 10.50 —10.50 9.80
CK5A/CK5BW024 23,000 TDR 10.50 —10.50 9.75
CK5A/CK5BW030 23,400 TDR 10.50 —10.50 9.80
COILS + 58MVP080-14VARIABLE SPEED FURNACE
CC5A/CD5AW024 23,000 TDR 10.50 —10.50 9.75
CC5A/CD5AW030 23,400 TDR 10.50 —10.50 9.90
CE3AA024 23,000 TDR 10.50 —10.50 9.80
CE3AA030 23,400 TDR 10.50 —10.50 9.95
CK3BA024 23,000 TDR 10.50 —10.50 9.95
CK3BA030 23,400 TDR 10.50 —10.50 9.95
CK5A/CK5BW024 23,000 TDR 10.50 —10.50 9.90
CK5A/CK5BW030 23,400 TDR 10.50 —10.50 9.95
COILS + 58U(H,X)V060-12VARIABLE SPEED FURNACE
CC5A/CD5AA024 23,000 TDR 10.50 —10.50 9.70
CC5A/CD5AA030 23,400 TDR 10.50 —10.50 9.80
CC5A/CD5AW030 23,400 TDR 10.50 —10.50 9.80
CE3AA024 23,000 TDR 10.50 —10.50 9.75
CE3AA030 23,400 TDR 10.50 —10.50 9.90
CK3BA024 23,000 TDR 10.50 —10.50 9.85
CK3BA030 23,400 TDR 10.50 —10.50 9.90
CK5A/CK5BA024 23,000 TDR 10.50 —10.50 9.85
CK5A/CK5BA030 23,400 TDR 10.50 —10.50 9.90
CK5A/CK5BW030 23,400 TDR 10.50 —10.50 9.90
See notes on pg. 18.

10
Combination ratings continued
UNIT
SIZE-SERIES INDOOR
MODEL TOT. CAP. BTUH
FACTORY-
SUPPLIED
ENHANCE-
MENT
SEER
EERA
Standard
Rating
Carrier Gas
Furnace or
TDR†Accessory TXV‡
030-50
CD5A/CD5AA030* 28,000 NONE 10.00 10.10 10.10 9.10
CC5A/CD5AA036 29,000 NONE 10.00 10.10 10.10 9.30
CC5A/CD5AW030 28,000 NONE 10.00 10.10 10.10 9.10
CD5AW036 29,000 NONE 10.00 10.10 10.10 9.30
CE3AA030 27,800 NONE 10.00 10.10 10.10 9.15
CE3AA036 28,600 NONE 10.00 10.10 10.10 9.25
CF5AA036 28,800 NONE 10.00 10.10 10.10 9.30
CK3BA030 28,000 NONE 10.00 10.10 10.10 9.10
CK3BA036 29,000 NONE 10.00 10.10 10.10 9.35
CK5A/CK5BA030 28,000 NONE 10.00 10.10 10.10 9.10
CK5A/CK5BA036 29,000 NONE 10.00 10.10 10.10 9.35
CK5A/CK5BN036 27,000 NONE 10.00 10.10 10.10 9.35
CK5A/CK5BT036 29,000 NONE 10.00 10.10 10.10 9.35
CK5A/CK5BW030 28,000 NONE 10.00 10.10 10.10 9.10
CK5A/CK5BW036 29,000 NONE 10.00 10.10 10.10 9.35
F(A,B)4ANF030 27,600 TDR 10.00 —10.00 9.20
F(A,B)4ANF036 28,200 TDR 10.00 —10.00 9.10
FC4BNF030 27,600 TDR & TXV 10.00 ——9.20
FC4BNF036 28,200 TDR & TXV 10.00 ——9.10
FF1(B,C,D)NA030 28,000 TDR 10.00 —10.00 9.10
FG3AAA036 28,000 NONE 10.00 10.10 10.10 9.20
FK4CNF001 29,000 TDR & TXV 11.00 ——9.95
40FKA/FK4CNF002 29,200 TDR & TXV 11.00 ——10.00
40FKA/FK4CNF003 29,400 TDR & TXV 11.50 ——10.30
40FKA/FK4CNF005 29,600 TDR & TXV 11.50 ——10.55
COILS + 58MVP040-14VARIABLE SPEED FURNACE
CC5A/CD5AW030 28,000 TDR 10.50 —10.50 9.50
CD5AW036 29,000 TDR 11.00 —11.00 9.85
CK5A/CK5BW030 28,000 TDR 10.50 —10.50 9.50
CK5A/CK5BW036 29,000 TDR 11.00 —11.00 9.85
COILS + 58MVP060-14VARIABLE SPEED FURNACE
CC5A/CD5AA036 29,000 TDR 11.00 —11.00 9.80
CK3BA030 28,000 TDR 10.50 —10.50 9.50
CK3BA036 29,000 TDR 11.00 —11.00 9.85
CD5A/CD5BW030 28,000 TDR 10.50 —10.50 9.50
CK5A/CK5BA036 29,000 TDR 11.00 —11.00 9.85
CK5A/CK5BT036 29,000 TDR 11.00 —11.00 9.85
CK5A/CK5BW030 28,000 TDR 10.50 —10.50 9.50
COILS + 58MVP080-14VARIABLE SPEED FURNACE
CC5A/CD5AW030 28,000 TDR 10.50 —10.50 9.55
CD5AW036 29,000 TDR 11.00 —11.00 9.90
CK5A/CK5BW030 28,000 TDR 10.50 —10.50 9.60
CK5A/CK5BW036 29,000 TDR 11.00 —11.00 9.95
COILS + 58MVP080-20VARIABLE SPEED FURNACE
CC5A/CD5AW030 28,000 TDR 10.50 —10.50 9.45
CD5AW036 29,000 TDR 11.00 —11.00 9.80
CK5A/CK5BW030 28,000 TDR 10.50 —10.50 9.50
CK5A/CK5BW036 29,000 TDR 11.00 —11.00 9.85
COILS + 58MVP100-20VARIABLE SPEED FURNACE
CC5A/CD5AW030 28,000 TDR 10.50 —10.50 9.75
CD5AW036 29,000 TDR 11.00 —11.00 10.10
CK5A/CK5BW030 28,000 TDR 10.50 —10.50 9.80
CK5A/CK5BW036 29,000 TDR 11.00 —11.00 10.10
COILS + 58MVP120-20VARIABLE SPEED FURNACE
CD5AW036 29,000 TDR 11.00 —11.00 10.05
CK5A/CK5BW036 29,000 TDR 11.00 —11.00 10.05
COILS + 58U(H,X)V060-12VARIABLE SPEED FURNACE
CC5A/CD5AA030 28,000 TDR 10.50 —10.50 9.70
CC5A/CD5AA036 29,000 TDR 11.00 —11.00 10.00
CC5A/CD5AW030 28,000 TDR 10.50 —10.50 9.70
CK3BA030 28,000 TDR 10.50 —10.50 9.70
CK3BA036 29,000 TDR 11.00 —11.00 10.05
CK5A/CK5BA030 28,000 TDR 10.50 —10.50 9.70
CK5A/CK5BA036 29,000 TDR 11.00 —11.00 10.05
CK5A/CK5BN036 27,000 TDR 11.00 —11.00 9.90
CK5A/CK5BT036 29,000 TDR 11.00 —11.00 10.05
CK5A/CK5BW030 28,000 TDR 10.50 —10.50 9.70
COILS + 58U(H,X)V080-16VARIABLE SPEED FURNACE
CC5A/CD5AW030 28,000 TDR 10.50 —10.50 9.80
CD5AW036 29,000 TDR 11.00 —11.00 10.15
CK5A/CK5BW030 28,000 TDR 10.50 —10.50 9.85
CK5A/CK5BW036 29,000 TDR 11.00 —11.00 10.20
030-34
CC5A/CD5AW030* 28,000 NONE —10.00 10.00 8.80
CC5A/CD5AA036 29,000 NONE —10.00 10.00 9.00
CC5A/CD5AW036 29,000 NONE —10.00 10.00 9.00
CE3AA030 28,000 NONE —10.00 10.00 8.90
CE3AA036 28,600 NONE —10.00 10.00 8.95
CF5AA036 28,600 NONE —10.00 10.00 9.00
See notes on pg. 18.