Installation Instructions
ELECTRICAL SHOCK HAZARD
Failure to follow this warning could cause personal injury or death.
Electrical shock can cause injury or death.
Disconnect power supply and install lockout tag before attempting to
install accessory.
SAFETY CONSIDERATIONS
Installation and servicing of this equipment can be hazardous due
to mechanical and electrical components. Only trained and qualified
personnel should install, repair, or service this equipment.
Untrained personnel can perform basic maintenance functions such
as cleaning and replacing air filters. All other operations must be per-
formed by trained service personnel. When working on this equipment,
obsmwe precautions in the literature, on tags, and labels attached to or
shipped with the unit and other safety precautions that may apply.
Follow all safety codes. Installation must be in compliance with
local and national building codes. Wear safety glasses, protective cloth-
ing, and work gloves. Have fire extinguisher available.
Read these instructions thoroughly and follow all warnings or cau-
tions included in literature and attached to the unit.
Recognize safety information. This is the safety alert symbol 7_' .
When you see this symbol on the unit and in instructions or manua)/!\_e
alert to the potential for personal injur3z Understand these signal words:
DANGER, WARNING, and CAUTION. These words are used with
the safety alert symbol. DANGER identifies the most serious hazards
which will result in severe personal injury or death. WARNING signi-
fies hazards which could result in personal injury or death. CAUTION
is used to identify unsafe practices which may result in minor personal
injury or product and property damage. NOTE is used to highlight
suggestions which will result in enhanced installation, reliability, or
operation.
CUT HAZARD
Failure to follow this caution may result in personal injury.
NOTE: On top filter rack for small cabinet, screw left side to coil
frame. On right side, bend tab on rack and screw to unit divider. Hold
height dimension shown in Fig. 2.
3. Install the bottom filter rack in the HVAC unit next to the indoor coil.
Filter rack will rest on the HVAC base and screw into the left and right
side of the coil frame. Be careful not to insert screws where coil dam-
age could occur. If using 2" (50.Smm) filters remove filter spacer. (See
Fig. 2A, 3Aand 4A.)
4. Install filters in rack. See Table 2 for sizes.
5. Replace filter access door on HVAC unit.
TABLE 1 - PACKAGE CONTENTS
Part No. Qty Description
1 Top Filter Rack
1 Bottom Filter Rack
CPFILTRK007A00 2 12 x 20 x 1in. (308.8 x 508 x 25.4mm) Filters
1 Hardware Bag
1 Instructions
1 Top Filter Rack
1 Bottom Filter Rack
1 14 x 24 x 1in. (355.6 x 609.6 x 25.4mm) Filter
CPFILTRK008A00 1 16 x 24 x 1in. (406.4 x 609.6 x 25.4mm) Filter
1 Hardware Bag
1 Instructions
1 Top Filter Rack
1 Bottom Filter Rack
1 16 x 24 x 1in. (406.4 x 609.6 x 25.4mm) Filter
CPFILTRK009A00 1 18 x 24 x 1in. (457.2 x 609.6 x 25.4mm) Filter
1 Hardware Bag
1 Instructions
Sheet metal parts may have sharp edges or burrs. Use care and
wear appropriate protective clothing and gloves when handling parts.
General
These filter racks can be used in either a horizontal or vertical
discharge application, and are designed to accommodate either l" or 2"
(25.4mm or 50.Smm) wide filters. Use caution not to damage indoor
coil during installation.
Installation
1. Remove the filter access panel on the HVAC unit. (See Fig. 1.)
2. Install the top filter rack in the HVAC unit next to the indoor coil.
Lift rack to the very top of the return chamber and screw rack into coil
frame on both the left and right side. Be careful not to insert screws
where coil damage could occur. If using 2" (50.Smm) filters remove
filter spacer. (See Figs. 2A, 3A, and 4A.)
i
Filter Accessory Panel
for Accessory Filter Rack
Fig. 1 -Filter Access Panel for
Accessory Filter Rack
