Carrier 40VCC3 Installation instructions

Central Controller
MODEL NAME
Edition: 2021-04
40VCC317FQEE
Installation and Owner’s Manual
Unit :
Temp. Setting :
Temp. Setting :
Auto
Unit :
On
Mon.
2013/11/20
16oC
O󰀨 Error
11:30
TEMP. FAN
NO. OK NO.
TEMP.
MODE
BACK
MENU
SCHEDULE

Parts and Functions-----------------------------------------------1
Operation-------------------------------------------------------------6
Central Controller Wiring Connection--------------------------21
Contents

Parts and Functions
Appearance
Mon.
2013/11/20 11:30
Unit : 11
Unit :
Auto Auto
Normal Lock
Error
01
O󰀩ce
201
Group : On O󰀨 Error
All
FAN
TEMP.
OK NO.NO.
TEMP.
MODE
BACK
MENU
SCHEDULE
EXQUISITE DESIGN & EXQUISITE LIFE
Temp. Setting:
20oC
1

English
Main interface display
Parts and Functions
Mon.
2013/11/20 11:30
Unit : 11
Unit :
Auto
Auto
Normal Lock
Error
01
O󰀩ce
201
Group : On O󰀨 Error
All
Temp. Setting:
20oC
2

Key descriptions
Parts and Functions
Mode/ESC key. Press this key for toggling between modes in the main interface and press this
key to go back to the previous interface.
Menu key. Press this key when in the main interface to enter the menu interface. The
SCHEDULE key below indicates the weekly timer setting.
Temperature adjustment keys. Press these keys to adjust the temperature in the main interface.
When the ECO function is not set, the temperature range is 16°C–30°C; temperature can be
varied in steps of 1°C. When the ECO function is set, the temperature range is limited. The
temperature adjustment keys are used for positioning the cursor when not in the main interface.
Unit No. adjustment keys. They are used for adjusting the unit or group unit no. These keys
are used for selecting between a unit or a group unit in the main and unit & group selection
interfaces; the options are as follows: unit→group→ALL→unit.
OK OK key
FAN
Fan key. Press this key to adjust the fan speed.
The options are (Low)→ (Middle) → (High) →
(Auto) → (Low)
AUTO
Auto Fan circulates as → → →
AUTO AUTO AUTO AUTO
ON/OFF key. In the main interface, short-press or tap this key to toggle between the ON/OFF
state of the unit or group (smallest unit) unit on which the cursor is placed. For example, if the
smallest unit in the group is in the ON state, after short pressing the ON/OFF key, all units in
this group will change to the OFF state. After pressing and holding the ON/OFF key down for
5 s, if the unit or smallest unit of a group on which the cursor is positioned is in the ON state,
all online units and groups will change to the OFF state, and vice versa. That is, if the smallest
unit in the group on which the cursor is positioned remains in the OFF state, after pressing and
holding down the ON/OFF key for 5 s, all units and groups online will change to the ON state.
MENU
SCHEDULE
MODE
BACK
TEMP.
TEMP.
NO.
NO.
3

English
Main interface icon descriptions
Weekly timer. When the weekly timer function is set for the units or groups
online, this icon will appear on the main interface.
Swing (reserved)
Error. When a unit or the smallest unit of a group malfunctions, this icon will
appear on the main interface.
Sleep (reserved)
Electrical heating (reserved)
Turbo (reserved)
Heat reclaim (reserved)
Health (reserved)
Child lock
Date (YY/MM/DD), time, week display area.
Mode of unit or smallest unit of group on which the cursor is
currently positioned.
Unit : 11 Unit or group on which the cursor is currently positioned.
Filter Filter (reserved)
Displays the unit or group on which the cursor is currently
positioned. Indicates whether the LIFO, Central, or Lock state is
selected.
Displays the set temperature of a unit or smallest unit of a
group on which the cursor is positioned or displays the ambient
temperature under the basic setting.
Parts and Functions
Mon.
2013/11/20 11:30
LIFO/Central/Lock
Temp. Setting:
20oC
AUTO
4

Error
01
Indicates the ON/OFF state or error in a unit or group on which the cursor is
positioned; error displays take priority.
O󰀩ce
201
Naming display. Displays the name of the unit or group on which the cursor is
positioned. If the length of the display text exceeds the display area, the text that
does not t the display area is represented by •••. If there is no name, the display
will show the unit/group as Unit1/GroupA.
Fan speed display.
Online unit display. When the cursor moves to ALL, all online units selected can be
controlled simultaneously. If the number of online units is more than 16, move the
cursor to ALL and press the RIGHT key to enter the next page. After entering the
next page, the arrow will be on the left side of the online units. Press the LEFT key
to go back to the previous page.
Group display.
Parts and Functions
AUTO
Unit :
All
Group :
5

English
Initialization
Function instructions
Operation
After powering on reset, the interface will display the following:
1. Mode options:
Pressing the MODE key in the main interface provides the following options in sequence:
Note: When the cursor is in the group area, the interface will show the state of the smallest unit in the group, and the
controller will adjust the mode of the smallest unit in the mode adjustment state.
2. Full control function:
When the cursor ashes under ALL, which is below the online unit display area, press the OK key to enter the full
control interface.
(1) When the online normal indoor units are controlled together, the state of the smallest indoor unit after entering the
full control function is displayed. If the smallest indoor unit is a normal indoor unit, the full control interface will be
shown as follows.
After the initialization is complete, indicated through a progress bar, you enter the main interface, and the ON/OFF
state of online units and groups will be shown on the unit and group areas.
Auto Cool Heat Fan Dry Auto
Auto AutoRecovery By-pass
6

Operation
Full Control
On/O󰀨
Temp. Setting
Fan
Mode
Control Mode
On O󰀨
Central Lock LIFO
Auto Cool Heat Fan Dry
Auto Low Middle High
28oC
7

English
Operation
3. Unit control function:
When the cursor ashes on any online unit in the main interface, press OK to enter the control interface of this
unit. Press the UP/DOWN/LEFT/RIGHT keys to move the cursor and press the OK key to conrm the selection.
Note: The functions in grey are reserved functions.
4. Group control function:
When the cursor ashes on any online group in the main interface, press OK to enter the control interface of this
group and press the UP/DOWN/LEFT/RIGHT keys to move the cursor, and press OK key to conrm the selection.
Note: The functions in grey are reserved functions
Unit Control
Group Control
Group A
Breeze/Super
Control Mode
10oC Heating
Name : O󰀩ce 102
On O󰀨
Central Lock LIFO
On O󰀨
HRV Linkage On O󰀨
Unit Included : 11 12 13 14 15 16 17 18
Unit 1
Filter
Control Mode
10oC Heating
Name : O󰀩ce 102
The region : D
Type : Normal Model
Ambient Temp.: 23oC
On O󰀨
Central Lock LIFO
On O󰀨
Breeze/Super On O󰀨
8

5. Weekly timer:
Press the MENU key in the main interface to enter the menu interface.
(1) When the Schedule icon ashes, press the OK key to enter the weekly timer conguration interface. When the
cursor ashes on +, press the OK key to enter the following set interface.
Select the appropriate setting: Category, Address, Temperature, Mode, ON/OFF, Time, Week. After adjusting
to the desired setting, move the cursor to Ok and press the OK key to complete the weekly timer setting. For
adjusting the temperature and time, press the OK key and the cursor will statically display; then, press the
UP/DOWN keys to select the desired temperature and time. After the appropriate temperature and time have
been selected, press the LEFT/RIGHT keys to move the cursor to other positions or press the OK key again to
allow the cursor to keep ashing. The interface display is as follows (the default selection is week index.)
Menu
Schedule Unit/Group
Setting
Setting ECO Error Code Service
Time Swing Basic
Setting
Additional
Function
Details Running
Time
(Figure 1)
Operation
Unit 13
Category Address Temp. Mode
Mon.
2013/11/20
On/Off Time Week
11:30
Sun.
Sat.
Thu.
Tue.
Every
day
Week
day
Mon
Wed
Fri.
On
Off
Auto
Cool
Heat
Fan
Dry
23oC
Ok
Cancel
All
Unit
Group
HRV
12 : 35
Schedule Setting
1 2 3 4 5 6 7 8
9 10 11 12 13 14 15 16
17 18 19 20 21 22 23 24
25 26 27 28 29 30 31 32
12 : 35
9

English
Operation
Unsuccessful weekly timing setting for incomplete
information, please set again?
Cancel Enter
(Figure 2)
Weekly timer Mon.
2013/11/20 11:30
Schedule (13 Set)
No. Week Address State Temp. Time
(Press to the previous page)
Thur.
Sun.
Mon.
(Press to the next page)
If conguration information is not set completely, press the OK key the following window will open:
The cursor is at Cancel by default; if you move the cursor to Enter and press the OK key, the interface in Figure
1 appears, to allow you to complete any incomplete information. If the OK key is pressed when the cursor is at
Cancel, the weekly setting will be cancelled, and the interface shown in Figure 2 will appear.
10

(2) Move the cursor to and press the OK key to enter the following interface; select the weekly timer that needs
to be cancelled. Move the cursor to Enter and press the OK key to cancel the weekly timer setting.
Operation
(3) Move the cursor to any set weekly timer No. and press the OK key to modify the weekly timer information.
(4) When there is a repeated or a conicting weekly timer setting between the new and old weekly timer setting,
press the OK key, and a window will pop up, allowing you to modify and conrm the setting (Figure 3).
This Timing has been set, please revise relevant
parameters.
Cancel Enter
6. Unit/Group setting:
In the menu interface, press the UP/DOWN/LEFT/RIGHT keys to select the unit/group setting. When the unit/
group setting icon ashes, press the OK key to enter, and the cursor will ash at the smallest unit No. Press
the OK key again, and the cursor will stop ashing and jump to rst key on the keyboard, x. Press the UP/
DOWN/LEFT/ RIGHT keys to move the cursor and press the OK key to select the desired key on the keyboard
and conrm.
Please select the No. you want to delete.
Cancel Enter
(Figure 3)
11

English
Press the UP/DOWN/LEFT/RIGHT keys to move the cursor to the included area and press the OK key to the enter
group setting interface (the group is automatically named as A to Z in sequence), as seen in Figure 1. The cursor will
be positioned at the smallest selectable unit; then, press the UP/DOWN/LEFT/RIGHT keys to move the cursor and
press the OK key to bring up the pop-up window, as seen in Figure 2. If part of the online unit is included in the current
group, press the UP/ DOWN/LEFT/RIGHT keys to move the cursor to the unit that needs to be cancelled, and press
the OK key to bring up the pop-up window seen in Figure 3.
Press the UP/DOWN/LEFT/RIGHT keys to move the cursor to the included area and press the OK key to bring
up the pop-up window seen in Figure 4. Press the UP/DOWN/LEFT/RIGHT keys to move the cursor to the group that
needs to be deleted and press the OK key to conrm.
Operation
Unit name and Group setting
Unit No. :
Group :
Unit/Group Name : Ofce 201
Delete HR
Dept. MarketingRoom
R&D PurchaseManager
Financial ServiceMetting
Delete
Space
Delete HR
Dept. MarketingRoom
R&D PurchaseManager
Financial ServiceMetting
Name : Group A
Optional Unit :
Contained Unit :
(Deletable Unit)
Delete
Space
Group A
(Figure 1)
12

If the current group needs to be named, press the UP/DOWN/LEFT/RIGHT keys to move across the keyboard.
When the keyboard is displayed, the cursor is initially at x, press the UP/DOWN/LEFT/RIGHT keys to adjust
and press the OK key to conrm.
Do you want to add Unit 10 to Group A?
Cancel Enter
(Figure 2)
Do you want to delete Unit 2 from Group A?
Cancel Enter
(Figure 3)
Please select the Group/Groups you want to delete.
Cancel Enter
(Figure 4)
Operation
13

English
7. Local setting:
In the Menu interface, press the UP/DOWN/LEFT/RIGHT keys to move the cursor, and when the setting icon
ashes, press the OK key to enter the interface shown in the gure below. Press the UP/DOWN/LEFT/RIGHT keys
to move the cursor and press the OK key to conrm. The Default Screen Timeout is 15 s, default Brightness is
60%, default Schedule Index is Week, and the default Place is set as Home.
Operation
Setting
8. ECO function:
(1) In the menu interface, press the UP/DOWN/LEFT/RIGHT keys to move the cursor. When the ECO icon
ashes, press the OK key to enter; the initial password is 841226. The interface shown in the gure below
will appear. Then, press the UP/DOWN keys to move the cursor and the LEFT/RIGHT keys to adjust the unit/
group. Press the OK key to conrm.
(2) The ECO function by default is set as OFF. The default maximum temperature is 26°C in heating mode, and
the default minimum temperature is 23°C in cooling/dry mode.
(3) Temperature and time value adjustment: When the cursor ashes at a value, press the OK key to stop the
cursor from ashing and press the UP/DOWN keys to adjust the temperature or time value; then, press the OK
key again to conrm and resume the ashing of the cursor and press the UP/DOWN keys to move the cursor.
(4) After setting the ECO function to any group, the temperature of all normal indoor units of the group is set to a
certain temperature.
ECO
Screen
Timeout
Place
Schedule
Index
15s
30%
Week Unit/Group
Mall O󰀩ce
Hotel Home
Brightness
30s
50%
1 min
60% 80%
3 mins Cancel
Setting
28
Off
Temp/ Range
On
Heat mode
highest temp.
limit
23
Cool/Dry mode
lowest temp.
limit
Type No overrun 12 hrs 30 mins permitted
Move cursor, press the Enter key to adjustSelected Unit/Group
(Unit 22)
14

9. Error code
In the menu interface, press the UP/DOWN/LEFT/RIGHT keys to move the cursor. When the
error code icon ashes, press the OK key to enter the interface shown in the gure below.
The current error can only show 1 error code, whereas the historic error can show 10 error
codes at a time. Press the UP/DOWN keys to scroll down the page to display error history
and the LEFT/RIGHT keys to select whether the current online unit or the smallest unit in the
current group and historic error needs to be displayed.
Operation
10. Service setting:
In the menu interface, press the UP/DOWN/RIGHT/LEFT keys to move the cursor to the
service setting icon and press OK key to enter the interface shown in the gure below.
Error Code
Current Error
Error
History
Error Code : 013
Move cursor to inquiry error historySelected Unit/Group
(Unit 1)
20/12/2013 11 : 20
Error Code : 013 20/12/2013 11 : 20
Error Code : 013 20/12/2013 11 : 20
Error Code : 013 20/12/2013 11 : 20
Error Code : 013 20/12/2013 11 : 20
Password
Service
Password recovery
15

English
Press the UP/DOWN keys to select a password and password recovery. When the cursor ashes in the
password position, press the Enter key to conrm and enter the password interface.
Press the UP/DOWN/LEFT/RIGHT keys to switch between numbers and the Enter/Cancel options. When the
cursor ashes on the number position, press OK to enter the corresponding number. After entering the 6-digit
password, press the OK key to conrm or move the cursor to the enter or cancel position to conrm or cancel.
Operation
Old Password
Cancel Enter
* * * * * *
1 2 3 4 5
6 7 8 9 0
New Password
Cancel Enter
* * * * * *
1 2 3 4 5
6 7 8 9 0
Service
Service
16

11. Time setting:
In the menu interface, press the UP/DOWN/LEFT/RIGHT keys to move the cursor. When the clock icon ashes,
press the OK key to enter the interface shown in the gure below. Press the UP/DOWN/LEFT/RIGHT keys to
move the cursor; when the cursor ashes, press OK to conrm and the cursor will stop ashing. Press the UP/
DOWN keys to adjust the values and press the OK key again to conrm; the cursor will resume ashing. Then,
press the UP/DOWN/LEFT/RIGHT keys to move the cursor. After adjusting the values, press directly the LEFT/
RIGHT keys to move the cursor to the next position.
12. Swing setting is a reserved function.
13. Basic setting function:
(1) In the menu interface, press the UP/DOWN/LEFT/RIGHT keys to move the cursor. When the basic setting
icon ashes, press the OK key and input the initial password 841226 to enter the interface shown in Figure
1. Press the UP/DOWN/LEFT/RIGHT keys to move the cursor, and press OK to conrm.
(2) The default model setting is self-adaption, the default language is English, and the ambient temperature
display is OFF.
(3) After setting the ambient temperature display to ON, the interface display will change from ‘temperature
setting’ to ‘ambient temperature display’. The ambient value is the unit or smallest unit of the group on
which the cursor is positioned. When pressing the UP/DOWN keys to adjust the temperature, the main
interface will rst statically display the temp. setting string and set temperature value, after which it will
display the statically ambient temperature value and ambient temperature display string after 3 s. Press the
LEFT/RIGHT keys to shift between the online unit or group, and press the MODE key to toggle between
modes. The interface will rst statically display the temp. setting string and the set temperature value, after
which it will display the statically ambient temperature value and the ambient temperature display string
after 3 s.
2013 Year
Time
Date 12 Month 22 Day
15 HourTime 25 Minute Mon.
Operation
17

English
(4) After changing the model selection, a window will pop asking you to reboot the system (Figure 2)
Basic Setting
Ambient Temp. Display
Language
Model VRF Unitary/Multi Self-adaption
Chinese English Italian
On O󰀨
(Figure 1)
Please reboot your system to accept model
changing!
Cancel Enter
(5) After changing the language, a window will pop asking you to reboot the system (Figure 3).
(Figure 2)
Please reboot your system to accept language
changing!
Cancel Enter
(Figure 3)
Operation
18