Carrier TruVu VVTBP-E2 Installation manual

TruVu™ VVTBP-E2
Installation and Start-up Guide
©2022 Carrier. All rights reserved. • Catalog No. 11-808-875-01 • 7/22/2022

Verify that you have the most current version of this document from www.hvacpartners.com, the Carrier Partner
Community website, or your local Carrier office.
Important changes are listed in Document revision history at the end of this document.
©2022 Carrier. All rights reserved.

Contents
What is the TV-VVTBP-E2?........................................................................................................................................... 1
Specifications ........................................................................................................................................................4
Zone sensors .........................................................................................................................................................7
Touchscreen devices ............................................................................................................................................8
Field-supplied hardware ......................................................................................................................................8
Installing the TV-VVTBP-E2 overview .......................................................................................................................... 9
Mounting the TV-VVTBP-E2 .......................................................................................................................................10
Wiring for power ........................................................................................................................................................13
To remove the TV-VVTBP-E2's cover................................................................................................................ 13
To wire for power ............................................................................................................................................... 14
Addressing the TV-VVTBP-E2 through the Comm/Service ports............................................................................15
To set the IP address......................................................................................................................................... 17
Addressing a network of controllers using the controller setup Local Network tab ............................................18
Method 1: To address when you know the serial numbers ....................................................................... 18
Method 2: To address when you do not know the serial numbers ............................................................ 19
Wiring for communications ......................................................................................................................................21
Wiring devices to the TV-VVTBP-E2's Rnet port.......................................................................................................22
Wiring devices to the TV-VVTBP-E2's Act Net port ..................................................................................................23
Wiring inputs and outputs.........................................................................................................................................24
Inputs................................................................................................................................................................... 24
Outputs ................................................................................................................................................................ 24
Wiring specifications ......................................................................................................................................... 25
To wire inputs and outputs............................................................................................................................... 25
To adjust input and output properties .....................................................................................................................28
Input values ........................................................................................................................................................ 29
Output values ..................................................................................................................................................... 30
Resolution values .............................................................................................................................................. 30
Offset/Polarity values ....................................................................................................................................... 31
Wiring the DAT sensor to the TV-VVTBP-E2's inputs ...............................................................................................32
Wiring specifications ......................................................................................................................................... 32
To wire and mount the DAT sensor................................................................................................................. 32
Wiring field-supplied actuators to the analog output .............................................................................................33
High-torque actuators ....................................................................................................................................... 33
Linked actuators ................................................................................................................................................ 34
Find and upload in the i-Vu® interface ....................................................................................................................36
Using the static pressure sensor ..............................................................................................................................37
To connect the duct tube(s) to the static pressure sensor .......................................................................... 37
Start-up.......................................................................................................................................................................38
Configuring the TV-VVTBP-E2's properties ..................................................................................................... 38
Performing system checkout........................................................................................................................... 39
Bypass damper....................................................................................................................................39
Variable frequency drive (VFD) ...........................................................................................................40
Sequence of operation..............................................................................................................................................41
Duct static pressure control ............................................................................................................................. 41
LAT monitoring and limiting............................................................................................................................. 41
Equipment fan off detection ............................................................................................................................ 42
Supply Air Temperature Alarm ........................................................................................................................ 42
Airside linkage.................................................................................................................................................... 42

Contents
Air source mode determination....................................................................................................................... 43
Adjusting the TV-VVTBP-E2 driver properties...........................................................................................................44
Driver ................................................................................................................................................................... 44
Device .................................................................................................................................................................. 46
Notification Classes........................................................................................................................................... 46
Calendars ............................................................................................................................................................ 47
Common Alarms ................................................................................................................................................ 48
Specific Events ................................................................................................................................................... 48
Custom Translation Tables............................................................................................................................... 49
BACnet Controller Properties........................................................................................................................... 49
BACnet Firewall.................................................................................................................................................. 50
Network Diagnostics - Statistics...................................................................................................................... 51
Network Diagnostics - Packet Capture........................................................................................................... 52
Act Net Bus ......................................................................................................................................................... 53
Communication Status ..................................................................................................................................... 55
Flow Calibration Archive ................................................................................................................................... 55
To set up Network Statistic trends.................................................................................................................. 55
To set up the controller through the Comm/Service ports ....................................................................................57
ModStat tab ........................................................................................................................................................ 57
Device tab ........................................................................................................................................................... 58
Ports tab.............................................................................................................................................................. 58
BACnet tab.......................................................................................................................................................... 59
Security tab......................................................................................................................................................... 59
Local Network tab.............................................................................................................................................. 59
To communicate through the BACnet/Service port network.................................................................................63
Wiring specifications ......................................................................................................................................... 64
To communicate locally through the Rnet port.......................................................................................................65
To set up a Local Access connection in the i-Vu® interface ....................................................................... 66
Troubleshooting .........................................................................................................................................................67
LEDs ..................................................................................................................................................................... 67
To use the Locator LED ..................................................................................................................................... 69
To configure custom Prog 1/2 LEDs............................................................................................................... 70
To get a Module Status report ......................................................................................................................... 70
Troubleshooting inputs and outputs ............................................................................................................... 71
To get a Device Log ........................................................................................................................................... 72
To get the TV-VVTBP-E2's serial number ........................................................................................................ 72
To take the TV-VVTBP-E2 out of service ......................................................................................................... 73
To replace the TV-VVTBP-E2's fuse.................................................................................................................. 73
To revert to default settings ............................................................................................................................. 74
Compliance ................................................................................................................................................................75
FCC Compliance................................................................................................................................................. 75
CE and UKCA Compliance ................................................................................................................................ 75
Industry Canada Compliance........................................................................................................................... 75
BACnet Compliance........................................................................................................................................... 75
Appendix A: TV-VVTBP-E2 Points/Properties..........................................................................................................76
Status................................................................................................................................................................... 76
Unit Configuration.............................................................................................................................................. 76
Maintenance....................................................................................................................................................... 78
Alarms ................................................................................................................................................................. 79
Linkage................................................................................................................................................................ 79
I/O Points ............................................................................................................................................................ 80
Appendix B: BACnet points list ................................................................................................................................81
Appendix C: Module Status field descriptions.........................................................................................................82

Document revision history ........................................................................................................................................84

TruVu™ VVTBP-E2 ©2022 Carrier.
Installation and Start-up Guide All rights reserved.
1
The TruVu™ Advanced Application Controller (part no. TV-VVTBP-E2):
•Runs 2 control programs
○a VVT bypass Product Integrated Control (PIC)
○an optional programmable Zone Controller II program
•Supports BACnet/IP communications on the 10/100 Ethernet port as a single node in a daisy-chain
configuration or as part of a network using a ring topology
•Supports DHCP IP addressing
•Has built-in network diagnostic capture functionality for troubleshooting
•Has network statistics that can be viewed numerically or as trend graphs
•Has a built-in static pressure sensor
•Supports Rnet devices
•Supports Act Net devices
•Works with the i-Vu® v7.0 or later system with the latest cumulative patch
•Provides 4 universal inputs, 3 binary outputs, and 2 analog outputs
The TV-VVTBP-E2, a component of the i-Vu® Control System, maintains supply duct static pressure by regulating
airflow and protects the air source from excessive supply air temperature. It has a built-in static pressure sensor
and actuator, uses a patented flow control algorithm, and mounts directly on the bypass duct damper actuator
shaft.
The TV-VVTBP-E2 PIC control program regulates the supply duct static pressure by controlling one of the following:
•The system's bypass damper
The controller's damper actuator provides 45 in/lbs (5 Nm) of torque. If the actuator's torque is insufficient,
the TV-VVTBP-E2 can be used to drive an external high-torque actuator.
•The air source supply fan's variable frequency drive (VFD)
The i-Vu® Control System uses linkage to exchange data between the zone terminals and their air source to form
a coordinated HVAC system. The system's air source controller, zone controllers, and bypass controller are linked
so that their data exchange can be managed by one zone controller configured as the VVT Master.
What is the TV-VVTBP-E2?

What is the TV-VVTBP-E2?
TruVu™ VVTBP-E2 ©2022 Carrier.
Installation and Start-up Guide All rights reserved.
2
The following illustration shows the TV-VVTBP-E2 in a typical i-Vu® Control System.

What is the TV-VVTBP-E2?
TruVu™ VVTBP-E2 ©2022 Carrier.
Installation and Start-up Guide All rights reserved.
3
You can use the TV-VVTBP-E2's physical communication ports as follows:
Port
Port type
For routing this type
of communication...
At...
Eth0
Eth1
10/100 Mbps Ethernet
BACnet/IP
BACnet/Ethernet
10 or 100 Mbps
S1
High-speed EIA-485 port
BACnet/MSTP
9.6 to 115.2 kbps

What is the TV-VVTBP-E2?
TruVu™ VVTBP-E2 ©2022 Carrier.
Installation and Start-up Guide All rights reserved.
4
The TV-VVTBP-E2 also has the following ports:
•Rnet port for connecting ZS sensors, an Equipment Touch, an TruVu™ ET Display, and Wireless Adapter for
wireless sensors
•Comm/Service USB ports for connecting locally to controller setup pages, the TruVu™ ET Display, or the
Carrier wireless service adapter
•Act Net port supports a combination of up to 5 Act Net addresses. Act Net devices must be addressed as
follows:
○Address 1is reserved for the built-in actuator
○Address 2and 3are reserved for the VAV Zone II Secondary Duct
○Address 4and 5for i-Vu® Smart Valves
Specifications
Driver
drv_fwex_< version >.driverx
Maximum number of control programs*
2
NOTE You can run 1 VVT bypass Product Integrated
Control (PIC) and 1 programmable Zone Controller II
program, OR up to 2 Zone Controller II programs.
Maximum number of BACnet objects*
12000
Third-party BACnet integration points
NOTE Must be on the BACnet/IP network
100
* Depends on available memory.
Power
24 Vac ±15%, 50–60 Hz, 50 VA
24 Vdc ±10%, 18 W
NOTE The above power consumption is for the controller only. Adding devices to
the Act Net bus increases total power consumed.
Actuator
Belimo brushless DC motor, torque 45 inch-pounds (5 Nm), runtime 154 seconds
Eth0, Eth1
10/100 BaseT, full duplex, Ethernet ports for BACnet/IP and/or BACnet/Ethernet
communication.
Under normal operation, network traffic not destined for this controller is repeated
to the other Ethernet port. When the controller is powered off, all traffic received on
one port is mirrored to the other port.

What is the TV-VVTBP-E2?
TruVu™ VVTBP-E2 ©2022 Carrier.
Installation and Start-up Guide All rights reserved.
5
Rnet port
•Supports up to 10 wireless and/or ZS sensors, and one Equipment Touch or
TruVu™ ET Display
•Supplies 12 Vdc/260 mA power to the Rnet across its rated temperature
range.
NOTE Ambient temperature and power source fluctuations exceeding the
listed operating ranges may reduce the power supplied by the Rnet port.
NOTE If the total power required by the sensors on the Rnet exceeds the power
supplied by the Rnet port, use an external power source. The Wireless Adapter,
Equipment Touch, or TruVu™ ET Display must be powered by an external power
source. See the specifications in each device's Installation and Start-up Guide to
determine the power required.
Act Net port
Supports a combination of up to 5 Act Net addresses. Act Net devices must be
addressed as follows:
○Address 1 is reserved for the built-in actuator
○Address 2and 3are reserved for the VAV Zone II Secondary Duct
○Address 4and 5for i-Vu® Smart Valves
Maximum power available for Act Net devices:
•AC supply - 25 VA (1 A)
•DC supply - 15W (0.625A)
•Use an external transformer if your devices exceed the maximum power.
Comm/Service ports
USB 2.0 host ports for setting up the controller and troubleshooting through a local
connection to a computer, connecting to the TruVu™ ET Display, or the Carrier
wireless service adapter.
Universal inputs
4
Inputs are configurable in the control program for 0–5 Vdc, 0–10 Vdc, thermistor,
dry contact, or pulse counter.
Input resolution
12 bit A/D
Input pulse frequency
10 pulses per second. Minimum pulse width (on or off time) required for each
pulse is 50 msec.
Analog outputs
2 analog outputs, 0–10 Vdc
Configurable as 12 Vdc pulse width modulated (PWM) control signal.
Binary outputs
One bank of 3 N.O. binary outputs. Each relay contact rated at 3.75 A max. @ 30
Vac/Vdc. Each bank is limited to Class 2 requirements of 100 VA / 4.2 A.
Configured normally open.
See Output values (page 30).
Output resolution
12 bit D/A
Integral static pressure
sensor
Precision differential pressure sensor 0–2 in. H2O, sensitive down to ±0.001 in.
H2O. Barbed tapered airflow connections accept 3/16 in. (4.75 mm) I.D. tubing.
Allows for readings across the 0–2 in. H2O range, accurate to ±3% of sensor
reading at 2 in. H2O.
Controller microprocessor
32-bit ARM Cortex-A8, 600MHz, processor with multi-level cache memory

What is the TV-VVTBP-E2?
TruVu™ VVTBP-E2 ©2022 Carrier.
Installation and Start-up Guide All rights reserved.
6
Memory
4 GBs eMMC Flash memory and 256 MB DDR3 DRAM
User data is archived to non-volatile Flash memory when parameters are changed,
every 90 seconds, and when the firmware is deliberately restarted.
NOTE When you change a parameter, you must wait 30 seconds before turning
the power off, in order for the change to be saved.
Real-time clock
Real-time clock keeps track of time in the event of a power failure for up to 3 days.
Protection
Field-replaceable glass fuse (3A fast-acting 5mm x 20mm)
The power and network ports comply with the EMC requirements EN50491-5-2.
LED status indicators
See LEDs (page 67) for details.
•Tricolor Net LED to show network status
•Tricolor Sys LED to show controller status
•A Tx (Transmit) and Rx (Receive) LED for Port S1
•Tx (Transmit) and Rx (Receive) activity LED and yellow link status LED for the
following ports:
○Ethernet port Eth0
○Ethernet port Eth1
•Output LEDs indicate status of each output.
•Prog 1/2 LEDs are customizable. See To configure custom Prog 1/2 LEDs
(page 70).
•Locator LED to find the controller during commissioning and to assess damper
rotation. See To use the Locator LED (page 69).
Environmental operating
range
32–122°F (0–50°C), 10–95% relative humidity, non-condensing
Physical
Fire-retardant plastic ABS, UL94-5VA
Terminal blocks and
connectors
Screw-type terminal blocks.
0.2 in (5.08 mm) pitch connectors
Mounting
Damper shaft/mounting bushing
Overall dimensions
A:
B:
C:
D:
Depth:
8.39 in. (21.30 cm)
5.95 in. (15.11 cm)
6.00 in. (15.24 cm)
7.52 in. (19.10 cm)
3.83 in. ( 9.72 cm)
Weight
1.8 lbs (0.82 kg)

What is the TV-VVTBP-E2?
TruVu™ VVTBP-E2 ©2022 Carrier.
Installation and Start-up Guide All rights reserved.
7
MTBF @ 77°F (25°C)
184,811 hours
BACnet support
Conforms to the BACnet Advanced Application Controller (B-AAC) and B-BBMD
Standard Device Profiles as defined in ANSI/ASHRAE Standard 135-2012 (BACnet)
Annex L, Protocol Revision 14
Compliance
United States of America:
FCC CFR47, Part 15, Subpart B, Class B
Canada:
Industry Canada Compliant, ICES-003, Class B
Contains IC ID: 6713A-STM300U
Europe: Mark, UK:
EN50491-5-2:2009; Part 5-2: EMC requirements for HBES/BACS used in
residential, commercial and light industry environment
RoHS Compliant: 2015/863/EU
REACH Compliant
Zone sensors
You can wire ZS sensors and/or a Wireless Adapter that communicates with wireless sensors to the TV-VVTBP-E2's
Rnet port. You can have up to 10 ZS and/or wireless sensors.
NOTES
•A control program can use no more than 5 ZS sensors, so you must use multiple control programs if your
Rnet network has more than 5 sensors.
•ZS and wireless sensors can share the Rnet with an Equipment Touch or TruVu™ ET Display.
CAUTION Rnet power
The Rnet port provides 12 Vdc at up to 260 mA. When determining which devices to put on the Rnet, verify that
the total current draw of the sensors does not exceed the controller's Rnet power. See the sensor's Installation
and Start-up Guide to determine the power required.

What is the TV-VVTBP-E2?
TruVu™ VVTBP-E2 ©2022 Carrier.
Installation and Start-up Guide All rights reserved.
8
Touchscreen devices
You can connect the TV-VVTBP-E2 to the touchscreen devices using the Rnet port or one of the Comm/Service
ports.
Rnet port
You can wire an Equipment Touch or TruVu™ ET Display to the TV-VVTBP-E2's Rnet port to view or change the
controller's property values, schedule equipment, view trends and alarms, and more, without having to access the
system's server. The Rnet port can have one Equipment Touch or TruVu™ ET Display, plus ZS sensors and/or a
Wireless Adapter that communicates with wireless sensors.
NOTE These touchscreen devices are not powered by the Rnet port.
•The TruVu™ ET Display requires a 24 Vdc external power source.
•The Equipment Touch requires a 24 Vac external power source.
USB ports
You can connect the TruVu™ ET Display to either of the TV-VVTBP-E2's Comm/Service ports to view or change the
controller's property values, schedule equipment, view trends and alarms, and more, without having to access the
system's server.
NOTES
•These touchscreen devices are not powered by the USB port.
•The TruVu™ ET Display requires a 24 Vdc external power source.
CAUTION A touchscreen device can share a power supply with the Carrier controller if:
•The power source shared by the controller and Equipment Touch is AC power.
•The power source shared by the controller and TruVu™ ET Display is DC power.
•You maintain the same polarity.
•You use the power source only for Carrier controllers.
Field-supplied hardware
Each TV-VVTBP-E2 installation requires the following field-supplied components:
•damper
•damper actuator (if high-torque actuator or slaved dampers are required)
•duct air temperature sensor
•power supply—24 Vac, 50VA or 24vdc 18W
•wiring

Installing the TV-VVTBP-E2 overview
TruVu™ VVTBP-E2 ©2022 Carrier.
Installation and Start-up Guide All rights reserved.
9
To install the TV-VVTBP-E2:
1 Mount the controller (page 10).
2 Wire the controller for power (page 13).
3 Set the controller's address (page 18, page 15).
4 Wire the controller to the BACnet/IP or BACnet/Ethernet network (page 21).
5 Wire the inputs and outputs (page 24).
Installing the TV-VVTBP-E2 overview

Mounting the TV-VVTBP-E2
TruVu™ VVTBP-E2 ©2022 Carrier.
Installation and Start-up Guide All rights reserved.
10
To mount the TV-VVTBP-E2
1 Turn the damper shaft to fully close the damper position. Ensure the damper is closed.
2 Mount the controller to the bypass duct by sliding the clamp assembly onto the damper shaft.
3 Mount and secure an enclosure to cover the TV-VVTBP-E2.
NOTE For service access, allow at least 1 foot (.3 m) of clearance between the front of the enclosure and
adjacent surfaces.
Mounting the TV-VVTBP-E2

Mounting the TV-VVTBP-E2
TruVu™ VVTBP-E2 ©2022 Carrier.
Installation and Start-up Guide All rights reserved.
11
4 Secure the controller and the actuator by screwing the rear mounting tab into the bypass duct, using the
screw that is supplied with the TV-VVTBP-E2.
NOTE We recommend that you use the M5 - .75 in. (19 mm), self-tapping screw that is shipped with the TV-
VVTBP-E2.
CAUTION Center the washer in the mounting screw slot. Secure the TV-VVTBP-E2 to allow lateral
movement of the damper shaft.
5 Hold down the TV-VVTBP-E2’s actuator release button and rotate the actuator clamp in the same direction
that closed the damper. Rotate the clamp until it stops, then rotate it back one notch.
6 Release the button.
7 Tighten the actuator clamp to the damper shaft by tightening the two M5 nuts.
8 Hold down the actuator release button and rotate the damper from fully closed to fully open. If the damper
traveled less than 90 degrees, do the following to prevent the damper traveling past fully open:
a) Loosen the appropriate stop clamp screw.
b) Move the stop clamp until it contacts the
edge of the actuator cam.
c) Tighten the screw.

Mounting the TV-VVTBP-E2
TruVu™ VVTBP-E2 ©2022 Carrier.
Installation and Start-up Guide All rights reserved.
12
9 Hold down the actuator release button, rotate the damper to verify that it opens and closes, then release the
button.
10 Connect the tube provided to either one of the controller's airflow ports. Using 1/4" poly tubing, connect the
other end to a duct static pressure probe (for example, Dwyer Instruments part #A-491, or the equivalent, for
a 6” length probe) located in the supply air duct downstream of the bypass damper, but before the first
branching of ductwork.
11 Leave the remaining airflow port open if using a ducted return, or connect it to room space if using plenum
return.

Wiring for power
TruVu™ VVTBP-E2 ©2022 Carrier.
Installation and Start-up Guide All rights reserved.
13
WARNING Do not apply line voltage (mains voltage) to the controller's ports and terminals.
CAUTIONS
•The TV-VVTBP-E2 is powered by a Class 2 power source. Take appropriate isolation measures when mounting
it in a control panel where non-Class 2 circuits are present.
•Carrier controllers can share a power supply as long as you:
•Maintain the same polarity.
•Use the power supply only for Carrier controllers.
To remove the TV-VVTBP-E2's cover
TIP To attach the cover to the base, secure a cable tie through the two cable tie brackets as shown below.
Wiring for power

Wiring for power
TruVu™ VVTBP-E2 ©2022 Carrier.
Installation and Start-up Guide All rights reserved.
14
To wire for power
1 Remove power from the power supply.
2 Remove the TV-VVTBP-E2's cover.
3 Pull the red screw terminal connector from the controller's power terminals labeled 24V.
4 Connect the power supply's wires to the red screw terminal connector.
5 Connect an 18 AWG or larger wire from the power supply's negative (-) terminal to earth ground. This wire
must not exceed 12 in. (30.5 cm).
6 Apply power to the power supply.
7 Measure the voltage at the red screw terminal connector to verify that the voltage is within the operating
range of 20.4 to 28.8 Vac or 21.6 to 28.8 Vdc.
8 To verify the polarity of the wiring, measure the voltage from the negative terminal of the red screw terminal
connector to a nearby ground. The reading should be 0V.
9 Insert the red screw terminal connector into the controller's power terminals.
10 Verify that the LED on top of the controller is on.