Carrier VAV Zone II Installation manual

V
VA AV V Z Zo on ne e I II I C Co on nt tr ro ol ll le er rs s
I
In ns st ta al ll la at ti io on n a an nd d S St ta ar rt t- -u up p G Gu ui id de e
CARRIER CORPORATION ©2019
A member of the United Technologies Corporation family · Stock symbol UTX · Catalog No. 11-808-602-01 · 8/30/2019

Verify that you have the most current version of this document from www.hvacpartners.com or your local Carrier
office.
Important changes are listed in Document revision history at the end of this document.
CARRIER CORPORATION ©2019. All rights reserved throughout the world. i-Vu is a registered trademark of Carrier
Corporation. All other trademarks are the property of their respective owners.

Contents
Introduction.................................................................................................................................................................. 1
What are VAV Zone II controllers? .....................................................................................................................1
Specifications ........................................................................................................................................................4
Linkage...................................................................................................................................................................6
Safety Considerations ..........................................................................................................................................8
Field-supplied hardware ......................................................................................................................................8
Installing the VAV Zone II ............................................................................................................................................ 9
Mounting the VAV Zone II ....................................................................................................................................9
To mount the controller and actuator .................................................................................................. 9
To connect duct tubes to the flow sensors ........................................................................................13
Wiring the VAV Zone II for power..................................................................................................................... 14
To wire the controller for power..........................................................................................................14
Addressing the VAV Zone II .............................................................................................................................. 15
Wiring for communications.............................................................................................................................. 15
Wiring specifications for BACnet MS/TP and ARC156......................................................................16
To wire the controller to the BACnet network ....................................................................................16
Wiring devices to the VAV Zone II's Rnet port ............................................................................................... 17
Wiring specifications ...........................................................................................................................17
To wire ZS sensors to the controller...................................................................................................17
To wire the Wireless Adapter for wireless sensors............................................................................18
To wire an Equipment Touch to the VAV Zone II................................................................................20
To wire the TruVu™ ET Display ...........................................................................................................21
Wiring sensors to the VAV Zone II's inputs .................................................................................................... 22
To wire the T55 sensor to the controller............................................................................................23
To wire the Supply Air Temperature sensor to the controller ...........................................................23
To wire the CO2 sensor to the controller ...........................................................................................24
To wire the Relative Humidity sensor to the controller .....................................................................25
Wiring a remote occupancy sensor ....................................................................................................26
Wiring equipment to the VAV Zone II's outputs ............................................................................................ 27
Wiring specifications ...........................................................................................................................27
Wiring diagram legend ........................................................................................................................28
No heat - Single duct or fan box application......................................................................................28
2-position hot water/steam heat - Single duct..................................................................................29
Modulating hot water/steam (ducted or baseboard) - Single duct application...............................30
Combination heat (ducted electric heat with modulating baseboard heat) - Single duct application
..............................................................................................................................................................31
Electric heat (ducted or baseboard) - Single duct application..........................................................32
SCR electric heat (ducted or baseboard) - Single duct application..................................................33
2-position hot water/steam (ducted or baseboard) - Fan box application ......................................34
Modulating hot water (ducted or baseboard) - Fan box application ................................................35
Combination heat (ducted electric heat with modulating baseboard heat) - Fan box application.36
2-stage electric heat (ducted or baseboard) - Fan box application..................................................37
SCR electric heat (ducted or baseboard) - Single duct application..................................................38
Wiring a field-supplied high-torque actuator to the analog output...................................................38
Start-up.......................................................................................................................................................................40
Configuring the VAV Zone II's properties........................................................................................................ 40
Configuring ZS Sensors..................................................................................................................................... 41
Performing system checkout........................................................................................................................... 41
Commissioning the VAV Zone II ...................................................................................................................... 42
Balancing the system using the i-Vu®/Field Assistant applications......................................................... 43
Prepare for balancing..........................................................................................................................43
Balance each zone..............................................................................................................................43

Contents
Balancing the system using Test & Balance tool ......................................................................................... 44
To calibrate VAV Zone airflow .............................................................................................................45
Upload calibration values to the i-Vu® application ...........................................................................46
Run a report in VAV Zone II (Optional)................................................................................................46
Balancing the system........................................................................................................................................ 47
Prepare for balancing..........................................................................................................................47
Sequence of operation ..............................................................................................................................................48
Temperature sensors ........................................................................................................................................ 48
Zone airflow control........................................................................................................................................... 49
Zone reheat control ........................................................................................................................................... 50
Demand control ventilation (DCV) and dehumidification using optional sensors................................... 51
Occupancy........................................................................................................................................................... 52
Alarms ................................................................................................................................................................. 53
Demand limiting ................................................................................................................................................ 54
Linkage................................................................................................................................................................ 54
Linkage modes and determination ................................................................................................................ 57
To adjust the driver properties..................................................................................................................................59
Driver ................................................................................................................................................................... 59
Device .................................................................................................................................................................. 60
Notification Classes........................................................................................................................................... 61
Calendars ............................................................................................................................................................ 62
Common Alarms ................................................................................................................................................ 62
Specific Events ................................................................................................................................................... 63
Switches, Jumpers, Options ............................................................................................................................. 63
Flow Calibration Archive ................................................................................................................................... 63
Act Net Network Details ................................................................................................................................... 64
Troubleshooting .........................................................................................................................................................65
LED's .................................................................................................................................................................... 65
To get the serial number .................................................................................................................................. 66
To restore factory defaults ............................................................................................................................... 66
To replace the battery ....................................................................................................................................... 67
To clean the airflow sensor orifice .................................................................................................................. 67
Compliance ................................................................................................................................................................69
FCC Compliance................................................................................................................................................. 69
CE Compliance ................................................................................................................................................... 69
BACnet Compliance........................................................................................................................................... 69
Appendix A: VAV Zone II Points/Properties ............................................................................................................70
Status................................................................................................................................................................... 70
Unit Configuration.............................................................................................................................................. 71
Setpoints ............................................................................................................................................................. 73
Alarm Configuration .......................................................................................................................................... 80
Service Configuration ........................................................................................................................................ 82
Maintenance....................................................................................................................................................... 89
Alarms ................................................................................................................................................................. 92
Linkage................................................................................................................................................................ 93
I/O Points ............................................................................................................................................................ 95
Appendix B: VAV terminal modes.............................................................................................................................98
Appendix C: ZS Sensor display for VAV Zone II ................................................................................................... 100
Appendix D: BACnet points list for the VAV Zone II Fan Terminal ...................................................................... 101
Document revision history ..................................................................................................................................... 104

VAV Zone II Controllers CARRIER CORPORATION ©2019
Installation and Start-up Guide All rights reserved
1
What are VAV Zone II controllers?
An i-Vu® Control System offers two VAV Zone II controllers, the VAV Zone II Single Duct (#OPN-VAVB1-02) and the
VAV Zone II Fan Terminal (#OPN-VAVB3-02), to control zone temperature using single duct or fan-powered
terminals in a Variable Air Volume (VAV®) application.
NOTE The single duct and fan terminal controllers are available in both English or Metric units. The metric version
has (-M) appended to the part number. Everything in this document applies to both versions.
You can disconnect the actuator from the controller and mount them separately, connecting them with just the
actuator cable or using an additional extension cable, up to a maximum distance of 300 feet.
Although a VAV Zone II can be included in a VVT system, this manual focuses mainly on its usage in VAV
applications.The VAV Zone II has a detachable actuator and maintains zone temperature by operating the terminal
fan and regulating the flow of conditioned air into the space. Buildings with diverse loading conditions can be
supported by controlling the local terminal's supplemental heat. The VAV Zone II provides dedicated control
functions for single duct, parallel fan box terminals and series fan box terminals with modulating heat, up to 2
stages of ducted heat, or combination baseboard and ducted heat.
The following illustration shows the VAV Zone II in a typical i-Vu® Control System.
Introduction

Introduction
VAV Zone II Controllers CARRIER CORPORATION ©2019
Installation and Start-up Guide All rights reserved
2
VAV Zone II Single Duct controller (#OPN-VAVB1-02)

Introduction
VAV Zone II Controllers CARRIER CORPORATION ©2019
Installation and Start-up Guide All rights reserved
3
VAV Zone II Fan Terminal controller (#OPN-VAVB3-02)
NOTE This document gives instructions for field-installation of a VAV Zone II in an i-Vu® System. However, VAV
Zone IIs are available factory-mounted to Carrier’s 35 single duct and 45 parallel and series fan terminals. All
terminals require an integrated duct temperature sensor.

Introduction
VAV Zone II Controllers CARRIER CORPORATION ©2019
Installation and Start-up Guide All rights reserved
4
Specifications
Driver
Part number
OPN-VAVB1-02
OPN-VAVB3-02
Driver
drv_vav1opn02
drv_vav3opn02
Power
24 Vac ±10%, 50–60 Hz
14 VA power consumption
26 Vdc (25 V min, 28.8 V max)
Single Class 2 source only, 100 VA or less
Actuator
Belimo brushless DC motor, torque 45 inch-pounds (5 Nm), runtime 154 seconds
Act Net port
To connect the actuator cable and the VAV Zone II
BACnet port
For communication with the controller network using BACnet ARC156 (156 kbps)
or BACnet MS/TP (9600 bps –76.8 kbps)
Rnet port
Supports up to 5 wireless and/or ZS sensors, and one Equipment Touch or
TruVu™ ET Display.
Supplies 12 Vdc/200 mA power to the Rnet at an ambient temperature of
77°F (25°C) with a 24 Vac nominal power source.
NOTE Ambient temperature and power source fluctuations may reduce the
power supplied by the Rnet port.
NOTE If the total power required by the sensors on the Rnet exceeds the power
supplied by the Rnet port, use an external power source. The Wireless Adapter,
Equipment Touch, or TruVu™ ET Display must be powered by an external power
source. See the specifications in each device's Installation and Start-up Guide to
determine the power required.
Local Access port
For system start-up and troubleshooting
Thermistor inputs
Accepts Precon type II thermistors (10kOhm at 77°F [25°C])
Range: -50°F (-45.5°C) to 250°F (121.1°C)
Dry contact inputs
A 3.3 Vdc wetting voltage used to detect the contact position, resulting in a 0.3
mA maximum sense current when the contacts are closed.
Voltage inputs
0-5 Vdc. Input impedance is approximately 30 kOhms
Input resolution
10 bit A/D
Binary outputs
#OPN-VAVB1-02: 1 binary output
#OPN-VAVB3-02: 3 binary outputs
Relay contact rated at 1 A max. @ 24 Vac/Vdc. Configured normally open.
Analog output
1 analog output, 0–10 Vdc (5 mA max). The controlled device must have a
minimum of 2000 Ohms resistance measured from its input to ground and must
share the same ground as the controller.

Introduction
VAV Zone II Controllers CARRIER CORPORATION ©2019
Installation and Start-up Guide All rights reserved
5
Output resolution
8 bit D/A
Integral airflow sensor
Precision differential pressure sensor 0–2 in. H2O, sensitive down to ±0.001 in.
H2O. Barbed tapered airflow connections accept 3/16 in. (4.75 mm) I.D. tubing.
Allows for readings across the 0–2 in. H2O range, accurate to ±5% of full flow at 2
in. H2O.
Battery
10-year Lithium CR2032 battery retains the following data for a maximum of
10,000 hours during power outages: control programs, editable properties,
schedules, and trends.
Protection
Built-in surge and transient protection for power and communications in
compliance with EN61000-6-1.
Incoming power and network connections are protected by non-replaceable
internal solid-state polyswitches that reset themselves when the condition that
causes a fault returns to normal.
The power, network, input, and output connections are also protected against
transient excess voltage/surge events lasting no more than 10 msec.
CAUTION To protect against large electrical surges on serial EIA-485
networks, place a PROT485 at each place wire enters or exits the building.
BT485 connector
You attach a BT485 (not included) to a controller at the beginning and end of a
network segment to add bias and to terminate a network segment.
Status indicators
LEDs indicate status of communications, running, errors, power, and digital
outputs
Environmental operating
range
32 to 130°F (0 to 54.4°C), 10–90% relative humidity, non-condensing
Storage temperature range
-24 to 140°F (-30 to 60°C), 0 to 90% relative humidity, non-condensing
Physical
UL94-5VA plenum rated enclosure for installation in plenum (or other space for
environmental air) in accordance with NEC Section 300.22 (c) and (d)
Controller and actuator
overall dimensions
Width:
Height:
8.9 in. (22.7 cm)
5.9 in. (15.0 cm)
Controller and actuator
mounting dimensions
7.1 in. (18.0 cm) from left side controller mounting hole centerline to actuator
mounting hole centerline
Controller overall
dimensions
Width:
Height:
Depth:
6.4 in. (16.3 cm)
5.7 in. (14.5 cm)
2.1 in. (5.3 cm)
Controller mounting
dimensions
5.3 in. (13.4 cm) from left side controller mounting hole centerline to right side
controller mounting hole centerline
Actuator overall dimensions
Width:
Height:
Depth:
3.0 in. (7.6 cm)
5.9 in. (15.0 cm)
2.5 in. (6.4 cm)
Actuator mounting
dimensions
4.4 in. (11.2 cm) from shaft centerline to actuator mounting hole centerline
Panel depth
2.5 in. (6.4 cm) minimum
Shaft dimensions
Minimum shaft diameter: .25 in. (.64 cm)
Maximum shaft diameter: .63 in. (1.59 cm)
Minimum shaft length: 1.75 in. (4.45 cm)

Introduction
VAV Zone II Controllers CARRIER CORPORATION ©2019
Installation and Start-up Guide All rights reserved
6
Weight
1.8 lbs (0.82 kg)
BACnet support
Conforms to the BACnet Advanced Application Controller (B-AAC) Standard Device
Profile as defined in ANSI/ASHRAE Standard 135-2012 (BACnet) Annex L,
Protocol Revision 9
Listed by
UL-916 (PAZX), cUL-916 (PAZX7), FCC Part 15-Subpart B, Class B, CE
Linkage
The i-Vu® Control System uses linkage to exchange data between the zone terminals and their air source to form
a coordinated HVAC system. The system's air source controller and zone controllers are linked so that their data
exchange can be managed by one zone controller configured as the VAV Master.
A VAV Master can have a maximum of 63 slave zone controllers reporting to it. An MS/TP network is limited to a
maximum of 60 controllers, but a VAV Master can have controllers from other networks as slaves.
A linked VAV system can be as simple as a single MS/TP network with a VAV Master and slaves, or it can be as
complex as multiple MS/TP networks with VAV sub-masters and slaves on other networks. See the following
examples.
EXAMPLE #1:A simple network. The VAV Master exchanges data between the slave controllers and the AHU
controller. The linked controllers on an MS/TP network must be sequentially addressed, and the VAV Master must
have the highest address.
A d dres s 1
2
3
4
5
6
7
8
VAV
M as te r
Slaves
Network #:
16116
A H U

Introduction
VAV Zone II Controllers CARRIER CORPORATION ©2019
Installation and Start-up Guide All rights reserved
7
EXAMPLE #2: The above network plus slave controllers on other networks.
A ddre s s 1
2
3
4
5
3
11
6
7
8
VAV
M as te r
Slaves
Network #:
1 6 11 6
Network #:
1 6 11 9
Network #:
1 6 13 0
A H U
EXAMPLE #3: The above network plus sub-masters and their slaves. (For VAV systems only. VVT systems do not
support sub-masters.) The sub-masters exchange data between their slaves and the VAV Master, and the VAV
Master handles data exchange for the whole system.
A ddre s s 1
2
3
4
5
23
19
6
7
8
VAV
M as te r
4
5
6
7
8
9
10
11
Sub-
M as te r
1
2
3
4
5
6
Sub-
M as te r
Slaves
Network #:
1 6 11 6
Network #:
1 6 11 5
Network #:
1 6 11 3
Network #:
1 6 11 7
Network #:
1 6 13 0
A H U
You set up linkage for the system by defining the Linkage properties for each controller. See Linkage Properties
(page 92).

Introduction
VAV Zone II Controllers CARRIER CORPORATION ©2019
Installation and Start-up Guide All rights reserved
8
Safety Considerations
CAUTION
Air conditioning equipment will provide safe and reliable service when operated within design specifications. The
equipment should be operated and serviced only by authorized personnel who have a thorough knowledge of
system operation, safety devices, and emergency procedures.
Good judgment should be used in applying any manufacturer's instructions to avoid injury to personnel or damage
to equipment and property.
WARNING Electrical Shock Hazard
Failure to follow this warning could cause personal injury, death, and/or equipment damage.
Disconnect all power to the unit before performing maintenance or service. Unit may automatically start if power is
not disconnected.
WARNING Follow all local, state, and federal laws regarding disposal of equipment containing hazardous
materials such as mercury contactors.
Field-supplied hardware
Each zone controller installation requires the following field-supplied components:
zone terminal unit
round or rectangular mounting bracket
space temperature sensor
supply air temperature sensor
2x4 in. standard single gang electrical box
transformer —24 Vac, 40 VA
two no. 10 x 1/2-in. sheet metal screws (to secure SAT sensor to duct)
two no. 6-32 x 5/8-in. screws (to mount space temperature sensor base to electrical box)
wiring
bushings (required when mounting SAT sensor in a duct 6-in. (15.2 cm) or less in diameter)
Optional:
contractors (if required for fan or electric heat)
indoor air quality sensor
relative humidity sensor
2 screws and 2 hollow wall anchors (to mount relative humidity sensor directly to wall)
valve and actuator for hot water heat (if required)

Installing the VAV Zone II
VAV Zone II Controllers CARRIER CORPORATION ©2019
Installation and Start-up Guide All rights reserved
9
1 Mount the controller to the VAV terminal. (page 9)
2 Wire the controller for power. (page 14)
3 Set the controller's address. (page 15)
4 Connect the controller to the BACnet MS/TP or BACnet ARC156 network. (page 15)
5 Wire devices to the Rnet port (page 16).
6 Wire sensor(s) to the controller. (page 22)
7 Wire equipment to the controller's outputs. (page 26)
Mounting the VAV Zone II
To mount the controller and actuator
To disconnect and mount the controller and actuator separately
Disconnect the actuator from the controller by inserting a screw driver in the slot on the back of the VAV Zone II
and pressing the tab. The actuator cable or an attached extension cable must connect to the controller's Act Net
port.
Installing the VAV Zone II

Installing the VAV Zone II
VAV Zone II Controllers CARRIER CORPORATION ©2019
Installation and Start-up Guide All rights reserved
10
Adding an extension cable
If you need to mount the actuator more than 14 in. from the controller, you can use an 18 AWG wire for an
extension cable. The maximum distance that the actuator and controller can be separated is 300 feet (91.4 m).
Connect the extension cable to the end of the actuator cable. You can use connectors or splice the wires.
Terminate the extension cable in the Act Net port on the controller.
To mount the VAV Zone II
1 Turn the damper shaft to fully close the damper.
2 Mount the controller to the VAV terminal by sliding the clamp assembly onto the damper shaft.

Installing the VAV Zone II
VAV Zone II Controllers CARRIER CORPORATION ©2019
Installation and Start-up Guide All rights reserved
11
NOTE For service access, allow at least 1 foot (.3 m) of clearance between the front of the controller and
adjacent surfaces.
3 Secure the controller and the actuator by installing the screws, anti-rotation slot's bushings, and o-rings that
are supplied with the VAV Zone II.
O-ring Bushing
Anti-rotation slot
NOTES
○Center the bushing in the slot. Failure to do so may cause the actuator to stick or bind.
○The VAV Zone II must be secured, but loose enough to allow movement. of the damper shaft.

Installing the VAV Zone II
VAV Zone II Controllers CARRIER CORPORATION ©2019
Installation and Start-up Guide All rights reserved
12
CAUTIONS
○You must use the screws, anti-rotation slot's bushings, and o-rings that are shipped with the VAV Zone II.
○Overtightening the screws so that the controller and actuator cannot move may damage the unit.
4 Hold down the VAV Zone II’s actuator release button and rotate the actuator clamp in the same direction that
closed the damper. Rotate the clamp until it stops, then rotate it back one notch.
5 Release the button.
6 Tighten the actuator clamp to the damper shaft by tightening the two M5 nuts.
7 Hold down the actuator damper release button and rotate the damper from fully closed to fully open. If the
damper traveled less than 90 degrees, do the following to set the actuator's fully open position:
a) Loosen the appropriate stop clamp screw. See figure below.
b) Move the stop clamp until it contacts the
edge of the actuator cam.
c) Tighten the screw.

Installing the VAV Zone II
VAV Zone II Controllers CARRIER CORPORATION ©2019
Installation and Start-up Guide All rights reserved
13
8 Hold down the actuator damper release button, rotate the damper to verify that it fully opens and closes, then
release the button.
To connect duct tubes to the flow sensors
The VAV Zone II controls airflow using the actuator and flow sensor.
1 Turn off the VAV Zone II's power.
2 Connect the tubes to the VAV Zone II's High and Low connectors.
3 NOTE Tubing should be at least 2 ft. (.61 meters) long for stable airflow measurement. The combined high
and low tubing length should not exceed 16.4 ft. (5 meters) in order to ensure accurate measurements.
4 Connect the other ends of the poly tubing to the airflow pickup located in the terminal's primary air inlet.
Avoid sharp bends in the tubing.
5 Connect High to High and Low to Low.

Installing the VAV Zone II
VAV Zone II Controllers CARRIER CORPORATION ©2019
Installation and Start-up Guide All rights reserved
14
Wiring the VAV Zone II for power
WARNING Do not apply line voltage (mains voltage) to the controller's ports and terminals.
CAUTIONS
The VAV Zone II is powered by a Class 2 power source. Take appropriate isolation measures when mounting it
in a control panel where non-Class 2 circuits are present.
Carrier controllers can share a power supply as long as you:
Maintain the same polarity.
Use the power supply only for Carrier controllers.
To wire the controller for power
1 To access the screw terminal connectors, lift up the controller's cover by pulling the tabs located on both
sides of the controller's left mounting bracket.
2 Remove power from the power supply.
3 Pull the screw terminal connector from the controller's power terminals labeled Gnd and 24 Vac.
4 Connect the transformer wires to the screw terminal connector.

Installing the VAV Zone II
VAV Zone II Controllers CARRIER CORPORATION ©2019
Installation and Start-up Guide All rights reserved
15
5 Apply power to the power supply.
6 Measure the voltage at the VAV Zone II’s power input terminals to verify that the voltage is within the
operating range of 21.6–26.4 Vac.
7 Connect a 4-inch (10.2 cm) wire from Gnd to the control panel.
8 Insert the screw terminal connector into the VAV Zone II's power terminals.
9 Verify that the Power LED is on and the Run LED is blinking.
Addressing the VAV Zone II
You must give the VAV Zone II an address that is unique on the network. You can address the VAV Zone II before
or after you wire it for power.
1 If the VAV Zone II has been wired for power, pull the screw terminal connector from the controller's power
terminals labeled Gnd and 24 Vac. The controller reads the address each time you apply power to it.
2 Using the rotary switches, set the controller's address. Set the Tens (10's) switch to the tens digit of the
address, and set the Ones (1's) switch to the ones digit.
EXAMPLE If the controller’s address is 25, point the arrow on the Tens (10's) switch to 2 and the arrow on
the Ones (1's) switch to 5.
10's 1's
1
3
4
5
2
7
8
9
6
0
1
3
4
5
2
7
8
9
6
0
CAUTION The factory default setting is 00 and must be changed to successfully install your VAV Zone II.
Wiring for communications
The VAV Zone II communicates using BACnet on the following types of network segments:
MS/TP communicating at 9600 bps, 19.2 kbps, 38.4 kbps, or 76.8 kbps
ARC156 communicating at 156 kbps
NOTE For more networking details, see the Open Controller Network Wiring Installation Guide.

Installing the VAV Zone II
VAV Zone II Controllers CARRIER CORPORATION ©2019
Installation and Start-up Guide All rights reserved
16
Wiring specifications for BACnet MS/TP and ARC156
Cable:
22 AWG or 24 AWG, low-capacitance, twisted, stranded, shielded copper wire
Maximum length:
2000 feet (610 meters)
WARNING Do not apply line voltage (mains voltage) to the controller's ports and terminals.
To wire the controller to the BACnet network
WARNING Attaching any ARCNET or MS/TP network to the Act Net port damages BT485s, DIAG485s, or
terminating resistors on that network.
1 Pull the screw terminal connector from the controller's power terminals labeled Gnd and 24 Vac.
2 Check the communications wiring for shorts and grounds.
3 Connect the communications wiring to the controller’s screw terminals labeled Net +, Net -, and Shield.
NOTE Use the same polarity throughout the network segment.
4 Set the communication type and baud rate.
For...
Set BACnet ARC156 or MS/TP
jumper to...
Set DIP switches 1 and 2 to...
ARC156
ARC156
N/A. Baud rate will be 156 kbps regardless of the
DIP switch settings.
MS/TP
MS/TP
The appropriate baud rate. See the MS/TP Baud
diagram on the controller.
NOTE Use the same baud rate for all controllers on the network segment.
5 If the VAV Zone II is at either end of a network segment, connect a BT485 to the VAV Zone II.
6 Insert the power screw terminal connector into the VAV Zone II's power terminals.
7 Verify communication with the network by viewing a Module Status report in the i-Vu® interface.