Casablanca Casablanca 19th Century User manual

19TH CENTUR Y 
OWNERS MANUAL

1
CIRCUIT BREAKER
(TRIP BREAKER FOR THE
CIRCUIT YOU WILL BE
WORKING ON)
FUSE BOX
(REMOVE FUSE FOR THE
CIRCUIT YOU WILL BE
WORKING ON)
•The blades in each pack are matched for equal
weight to assure smooth fan operation. If
more than one fan is being installed, be
careful not to mix blades from different
cartons.
•Inspect the contents of your carton for
possible shipping or handling damage and
report any such damage directly to your
authorized Casablanca dealer.
•It is always a good idea to have an assistant
to help with the installation.
•When cleaning, painting, or working near
your fan, be very careful of the fan and blades.
Always turn the power OFF to the ceiling fan
before servicing it, working on it, or replacing
light bulbs.
•Never insert anything into the path of the
fan blades while the fan is in operation.
• Never install a fan over a pool or spa.
•Never operate a fan that has been damaged
in any way. Contact Casablanca Fan Company
by calling 1-888-227-2178, or contact your
local authorized Casablanca dealer for
assistance in obtaining service.
CONTENTS
READ AND SAVE THESE INSTRUCTIONS
•All wiring must be in accordance with the National Electric Code ANSI/NFPA 70-1993 and the appropriate local electrical
codes. The National Electric Code requires proper grounding as a precaution against electrical shock. A qualified electri-
cian should be consulted if you are unsure.
• This fan is designed to be installed on an existing electrical outlet box. The outlet box must be UL Listed for ceiling fan
installations, if it is not, a new box must be installed. Casablanca extension poles are available for sloped or high ceiling
installations.
•This ceiling fan requires a grounded electrical supply of 120 VAC, 60 Hz and a minimum 15 amp circuit. The maximum
current requirement for the fan with light fixture is 3.8 amps. The fan uses about 1 amp or 100 watts. Maximum light
current is 2.8 amps or 340 watts of lighting.
•Where wire nuts are employed, be sure all bare wires are within the connectors. When installing the canopy hatch, make
sure all wires are within the canopy and that no wires are being pinched.
For best performance and for your warranty to be valid,
use only genuine Casablanca blades, light fixtures, and accessories.
SAFE USE
Safety and the proper operation of your Casablanca fan both require a thorough knowledge of the product
and proper installation; therefore, before attempting to install and operate your Casablanca fan, read this
owner’s manual completely and carefully. Retain this manual for future reference.
SAFETY FIRST
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
MOUNTING RECOMMENDATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
PREPARATION INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
FAN INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
CONTROL FEATURES:
INTELI•TOUCH OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
BEFORE YOU START
P/N 6943010 REV. D P/D NOV00PDG
CAUTION: To avoid possible electrical shock, make certain that electricity is turned off at
the circuit breaker or fuse box before attempting any installation procedure.
18″
84″
70″

2
Calculation of 32°
Use the tear-off Ceiling Angle Template card inserted in the
back of this manual, it provides you with a simple ‘go’ or
‘no-go’ for installing your fan on a sloped ceiling.
SLOPED CEILING INSTALLATIONS
MOUNTING RECOMMENDATIONS
7′MINIMUM
Pole Length
Standard
18"
24"
36"
48"
Ceiling Height
10'
11'
12'
13'
14'
Suggested Extension Pole Lengths
When to Use Extension Poles
For best performance and best appearance,
an extension pole should be used with
your Casablanca fan when installing on
high (cathedral) ceilings or sloped ceil-
ings. Casablanca offers standard poles in
increments of 6″up to 5′. Custom poles
are available in lengths up to 10′. See your
Authorized Casablanca Dealer for details.
32°
BLADES MUST BE A
MINIMUM OF 7′
ABOVE THE FLOOR
EXTENSION
POLE
MAXIMUM
HANG-TRU®
ANGLE 32º
Before mounting your Casablanca fan, read the following helpful recommendations. The location of the fan, air circulation,
and fan size are all important factors to consider before installation.
Location
Ceiling fans have practical uses in almost every room in your home. We suggest you follow these mount-
ing recommendations as you decide where to install your Casablanca fan.
• For safety reasons, the fan blades must be a minimum of 7′above the floor.
• Do not locate the fan in a doorway or above a swinging door.
• In any installation, the tips of the blades must be at least 18″from the wall in order to
provide sufficient clearance for the blades.
• In bedrooms, fans work best when mounted above the foot of the bed.
• Over pool tables, be sure to provide plenty of clearance to avoid damage from pool
cues.
• In kitchens be sure to allow for open cupboard doors to clear the fan blades.
• Do not install a fan close to, or over, a pool or spa. High humidity combined with
corrosive gases will destroy the finish and warp the blades.
Fan Size
Variable fan speed capability permits the use of a full-size 52″fan even in
smaller rooms. For very large rooms, two fans may be needed.
EXAMPLE 1
This slope is less than 32˚.
It is OK to install your fan.
EXAMPLE 2
This slope is 32˚. This is the maximum
slope that will allow the fan to hang
straight down. It is OK to install your
fan.
EXAMPLE 3
This slope is more than 32˚.
Your fan will not hang straight down, an
adaptor is necessary. Contact your local
Authorized Casablanca Dealer in regards
to purchasing a “Slope Ceiling Adaptor.”
Note: Fan may wobble or vibrate if
pole length is not long enough and
inside blade is too close to downslope
or side wall. Extending pole length
will usually solve problem.
Note: The canopy cover (Step 11) can
NOT be used on a sloped ceiling.

3
PREPARATION INSTRUCTIONS
Unpacking: Before assembling and installing your ceiling fan, remove all parts from the shipping cartons and check them
against the parts listed here. Before discarding packaging material, be certain that all parts have been removed.
DOWNROD COVER
DOWNROD & BALL
ASSEMBLY
PERMA•LOCK™ HARDWARE
GETTING STARTED
Carton Contents
The fan carton contains the fan body, warranty card, owner's
manual, and all the parts necessary to assemble and install your
Casablanca ceiling fan. These parts are shown at the start of
each installation section. Before you start, go through this
Owner’s Manual and confirm that you have all the parts shown
in each section.
Be sure to use only genuine Casablanca blades. The blade
shrink wrap holds 4 blades of matched weight. If more than
one fan is being installed, be sure not to mix blade sets.
CAUTION: When removing the shrink wrap,
be careful not to scratch the blades.
METAL DOWNROD
GASKET
RUBBER DOWNROD
GASKET
INSTALL RUBBER GASKET
Prepare the downrod as follows:
Step A. Insert the small lip of the rubber gasket into the
downrod cover.
ATTACH COVER TO DOWNROD
INSTALL METAL GASKET
Step B. Slide the downrod cover, rubber gasket first, onto the
downrod by using a twisting motion. Continue until the rub-
ber gasket is flush with the downrod ball.
Step C. Attach the metal gasket onto the downrod assembly
as shown. Using the provided screw, secure the metal gasket.
Tighten the screw by hand only.
CAUTION: Do not attach the cover onto the
downrod by pounding the downrod into the
floor. This will damage the hanging mecha-
nism and may cause the fan to fall.
19th Century™

4
FAN PREPARATION
MOTOR
COUPLING
TAPERED
THREAD
MOTOR
WIRES
GROUND
WIRE
Step E. Using the provided allen wrench, loosen the allen set
screw. Thread the downrod into the motor coupling until it
stops turning, this will take at least four and a half full turns.
Step F. Securely tighten the allen set screw with the provided
allen wrench to ensure safe operation of your fan.
CAUTION: Failure to fully lock in the down-
rod before securely tightening the locking
bolt may cause the fan to fall during nor-
mal operation!
IMPORTANT SAFETY INFORMATION!
BEFORE STARTING THE INSTALLATION OF YOUR CEILING FAN,
INSTALL THE THREADED DOWNROD INTO THE MOTOR COUPLING AND
LOCK THE ASSEMBLY
ALLEN
SET SCREW
DOWNROD
&
BALL
ASSEMBLY
Prepare for fan installation as follows:
Step D. Route the wires from the motor through the
Perma•Lock™ downrod and ball assembly, keeping the wires
to one side of the cross pin.
GETTING STARTED
Installing a New Ceiling Fixture Outlet Box
If you do not have an existing fixture located where you wish
to place your Casablanca fan, an approved ceiling fixture
outlet box must be installed and wired.
Using Existing Ceiling Fixture Outlet Box
After turning the power OFF at its source (either circuit breaker
or fuse box), lower the old fixture and disconnect the wiring.
Check the ceiling fixture outlet box to be sure that it is
marked ‘Approved for ceiling fan mounting’. If it is not, a new
box must be installed.
Warning: To reduce the risk of fire, electrical shock,
or personal injury, mount to outlet box marked ac-
ceptable for ceiling fan support using the mounting
hardware provided with the outlet box. NOTE: The fan weight is 35 pounds.
NOTE: The downrod has a tapered thread
that is designed to lock completely when
correctly installed.
ALLEN SET SCREW
1⁄4-20 x 1⁄4"
(PRE-INSTALLED)
3mm
ALLEN WRENCH

5
ADAPTOR PLATE INSTALLATION
JOIST
CEILING
WIRING
CROSSBAR
MOUNTING
BRACKET
FLAT
WASHER
GREEN
GROUND
WIRE
CEILING FAN
APPROVED
WIRING BOX
RIDGE
SIDE
DOWN
APPROVED
OUTLET BOX
HARDWARE
Note: After removing the old fixture, check the outlet box
to insure that it is supported by a joist or beam across its
upper surface. If not, a 2" x 4" stud must be installed.
Step 1. Remove the knockout plug in the center of the outlet
box or drill a 1/2" hole for the lag screw to pass through. Then
drill a 1/4" guide hole into the joist or beam to a depth of 3".
CAUTION: To reduce the risk of personal injury,
use only the mounting hardware provided with
the approved outlet box to install the crossbar
mounting bracket.
CEILING HARDWARE
CROSSBAR
MOUNTING
BRACKET
WIRE NUT (4)
ADDITIONAL HARDWARE
21/4" x 8-32 ROUNDED
HEAD SCREW (2)
FLAT WASHER (2)
1" x 8-32 ROUNDED
HEAD SCREW (2)
SUPPORT INSTALLATION PARTS
CANOPY
ADAPTOR
PLATE LAG SCREW
3/8" #7 X 5" (1)
LARGE
FLAT WASHER
3/8" (1)
WARNING!
SUPPORT DIRECTLY TO
BUILDING STRUCTURE ONLY.
19th Century™

6
Step 2. Route the outlet box wires through the 1/2″ diam-
eter outer hole of the canopy adaptor plate. Attach the
crossbar and canopy adaptor plate to outlet box with screws
provided.
Step 3. With the large washer attached, pass the lag screw
through the center hole of canopy adaptor plate and screw
into guide hole. Tighten until outlet box is firmly mounted
to beam. This box must be firmly secured to the ceiling. We
recommend that the ceiling fixture outlet box be of suffi-
cient capacity enabling it to support the weight of fan and
light fixture under any conditions.
LAG
SCREW
LAG SCREW INSTALLATION
1/2″DIAMETER
OUTER HOLE
LARGE
WASHER
CANOPY INSTALLATION
CANOPY HARDWARE
CANOPYCANOPY
HATCH
CANOPY LOCK WASHER (4)
CANOPY SCREW (4)
Step 4. Attach the canopy to the crossbar mounting bracket behind the
installed outlet adaptor plate with three of the 8-32 x 21/2″long canopy
screws and lock washers provided with your Casablanca fan. Hand tighten
until snug against the ceiling.
CANOPY
SCREW
CANOPY
LOCK
WASHER
FEED OUTLET BOX
WIRES THROUGH
CANOPY OPENING
Note: On sloped ceilings, align the
canopy opening toward the top or peak
of the room.

7
HANGING THE FAN
Step 5. To hang the fan body in the canopy, hold the fan
body firmly and insert the nylon ball into the canopy open-
ing. Rotate fan body until slot on nylon ball fits into pin
opposite canopy opening.
CANOPY
BALL
SLOT PIN
CANOPY ELECTRICAL CONNECTIONS
2 WHITE WIRES
2 BLACK WIRES
WIRE NUT
3 GREEN WIRES
CANOPY HATCH INSTALLATION
Step 7. Tuck the wires into the canopy
with the wire nuts pointed upwards, so
that the WHITE and BLACK wires are on
opposite sides of the canopy and all wires
are clear of the canopy opening.
Step 8. Install canopy hatch with the last
canopy screw and lock washer. To do this,
tilt the fan body away from the hatch
opening.
Tighten the screws firmly by hand only,
TILT THE FAN
TO INSTALL
LAST CANOPY
SCREW
CANOPY
HATCH
CANOPY
SCREW
LOCK
WASHER
Step 9. Straighten the fan, then check
to ensure that there is no movement be-
tween the canopy and ceiling or Hang-Tru
ball and top support shaft.
Note: Write down the
Serial Number and the
model number for future
reference.
Step 6. Connect the fan wires to the outlet box
wiring by placing the bare ends of the wires to-
gether and then securing with a wire nut.
Connect in this order:
• GREEN leads from mounting plate and fan
to GROUND conductor of power source.
Secure with wire nut.
• WHITE wire from fan to white NEUTRAL wire
in ceiling fixture outlet box.
Secure with wire nut.
• BLACK wire from fan to black POWER wire
in ceiling fixture outlet box.
Secure with wire nut.
Inspect each wire nut and ensure that no bare
wire is visible; pull on each wire to test the con-
nection is mechanically sound.
NOTE: The fan weight is 35 pounds.
19th Century™

8
CANOPY
COVER
DISASSEMBLE CANOPY AND MOTOR COVERS
Step 11. Take the two pieces of the
canopy cover and assemble them around
the downrod as shown. Using the four
screws removed in Step 10, assemble the
canopy cover.
Slide the canopy cover to the ceiling and
secure to the downrod using the two pro-
vided screws. Tighten by hand only.
INSTALL CANOPY COVER
Step 12. Take the two pieces of the mo-
tor cover and assemble them around the
downrod as shown. Using the two screws
removed in Step 10, assemble the motor
cover.
Slide the motor cover down onto the top
of the fan and secure to the downrod us-
ing the two provided screws.
Using the screwdriver, tighten securely
by hand only.
INSTALL MOTOR COVER
Step 10. Remove the screws from the canopy cover and
the motor cover and set aside for later use. MOTOR
COVER
CAUTION: The canopy cover can NOT be used
on sloped ceilings.
CANOPY
COVER
SCREWS FROM
STEP 10
PROVIDED
SCREWS
SCREWS FROM
STEP 10
PROVIDED
SCREWS

9
ATTACH BLADE HOLDERS
Step 13. Attach the blades to the blade holders by align-
ing the screw holes of the holder with the holes of the
blade.
Attach the blade holder using the four blade screws and
blade washers provided for each blade.
Using the screwdriver, tighten securely by hand only.
BLADE
SCREW
BLADE HARDWARE
BLADE
WASHER BLADE
HOLDER
BLADE
BLADE
SCREW
BLADE
WASHER
INSTALL BLADE ASSEMBLY
Step 14. Remove the blade holder screw from the fan.
Slide the blade assembly into the cross bar, assuring that
the alignment holes line up.
Reinstall the blade holder screw, making sure that the
blade assembly is secure and does not rotate when turned.
Using a wrench or pliers, tighten securely by hand only.
BLADE HOLDER
SCREW
ALIGNMENT
PIN
BLADE
ASSEMBLY
BLADE
HOLDER
SCREW
ALIGNMENT
HOLES
19th Century™

10
LIGHT KIT WIRING
WIRE NUT
NOTE: If you do not desire to install the
light kit, see “Optional Switch Housing Cup”
installation instructions on Page 11.
Step 15. Remove the wire nuts on the BLACK
and WHITE wires from the fan. If necessary re-
move the insulation from the last 1/2” of each
wire (fan and light fixture).
Step 16. Attach the switch housing wires to
the light fixture wires by placing the bare ends
of the wires together and then securing with a
wire nut. Connect in this order:
• WHITE wire from fan to WHITE wire from
light fixture. Secure with wire nut.
• BLACK wire from fan to BLACK wire from
light fixture. Secure with wire nut.
Inspect each wire nut and ensure that no bare
wire is visible; pull on each wire to test the
connection is mechanically sound.
INSTALL LIGHT KIT
Step 17. Slide the light kit over the
threaded pipe from the switch housing.
Assure that no wires are pinched.
Secure the light kit to the fan with the
finial.
Tighten securely by hand only.
FINIAL
THREADED
PIPE
WIRE
NUT

11
GLASS & BULB INSTALLATION
GLASS SHADE
SCREWS
Step 18. Loosen the three glass screws for each
fixture so the end of the screws are flush with
the inside of the fixture.
Slide the glass shade into the fixture and hold
firmly. Turn each screw several times, going in
a circle, to assure that all glass screws have en-
gaged the glass.
Tighten securely by hand only.
Step 19. Install the four 60 Watt type A15 bulbs
into each fixture. GLASS SHADE
GLASS HARDWARE
60 WATT TYPE A15
INCANDESCENT BULB GLASS SHADE
Note: Do NOT use standard (A-19) bulbs. This
commonly available size is too large in diameter; the
proximity of the bulb to the glass will not allow for
adequate air circulation.
CAUTION: TO REDUCE THE RISK OF FIRE
USE MAX FOUR 60W STANDARD BASE
A15 INCANDESCENT LIGHT BULBS
60 WATT TYPE A15
INCANDESCENT BULB
19th Century™
OPTIONAL SWICH HOUSING CUP
NOTE: This step is ONLY performed if
you have chosen NOT to install the light
kit.
Slide the optional switch housing cup over
the threaded pipe from the switch hous-
ing. Assure that no wires are pinched.
Secure the cup to the fan with the finial.
Tighten securely by hand only.
FINIAL
THREADED
PIPE
OPTIONAL SWITCH
HOUSING CUP

12
R
INTELI•TOUCH ♦SINGLE W-32 INSTALLATION
The wall control installs in the same manner as an ordinary light switch, using an existing junction box and wiring. This
controller is designed to signal the fan microcomputer as well as perform normal switching operations. For this reason the
following precautions must be observed:
1. Use only the Casablanca W-32 wall control.
2. Do not use any additional control with your Inteli-Touch
fan (for example, dimmer, fan speed control, etc.).
3. Do not use more than one fan per wall control.
4. No other light fixtures or electrical appliances may be con-
nected on the circuit controlled by the W-32 wall control
unit.
SWAP THESE
TWO WIRES WHEN
NECESSARY
(SEE NOTE BELOW)
INTELI•TOUCH ♦DUAL W-32 INSTALLATION
W-32 is used to describe either white (-11) or ivory finish.
1. Remove the screws and switch plate from the existing
switch box.
2. Remove the screws holding the switch in the switch box.
3. Pull the existing switch from the switch box to expose the
wire connections.
4. Remove the two wires from the switch.
5. Connect the two wires just removed from the switch to
the W-32 wall control black wire and black/white stripe
wire. Secure these connections with wire nuts.
6. Install the W-32 in the wall box with the two long screws
provided.
7. Install the wall plate with the two color matched screws.
R
R
SWAP THESE TWO WIRES
WHEN NECESSARY
(SEE NOTE BELOW)
END
OF
LINE
IN
LINE
To control the fan and lights from two locations
(a three-way circuit), use 2 W-32 wall controls.
1. Remove the screws and switch plate from the
existing switch box and the screws holding
the switch in the switch box.
2. Pull the existing switch from the switch box
to expose the wire connections.
3. Determine which wire is connected to the com-
mon terminal of the 3-way switch. (The
terminal will be marked on switch).
4. Remove the wire from the common terminal
of the 3-way switch. Connect this wire to the
remaining black/white striped wire on the W-
32 control. Secure this splice with a wire nut.
5. Remove the two remaining wires from the 3-
way switch. Connect one of these wires to a
black wire on the W-32 control. Secure the
splice with a wire nut. The remaining wire is
to be connected to the other black wire on
the W-32. Secure the splice with a wire nut.
6. Install the W-32 in the wall box with the two
long screws provided.
7. Install the wall plate with the two short color-
matched screws provided.
8. Installation of the second W-32 control is iden-
tical. Repeat steps 1 through 8.
INTELI•TOUCH © INSTALLING THE W-32 WALL CONTROL
CAUTION! Ensure power is turned OFF at the breaker
or fuse panel before starting installation.
CAUTION! Ensure power is turned OFF at the breaker
or fuse panel before starting installation.
NOTE: If your wall control operation is reversed, i.e., fan switch
controls lights and light switch controls fan, simply swap the
two W-32 black/white stripe wires.
NOTE: If your wall control operation is reversed, i.e., fan
switch controls lights and light switch controls fan, simply
swap the two W-32 black/white stripe wires.
R

13
INTELI•TOUCH OPERATION ♦POWER
+
+++
Programmed into every Inteli-Touch Series fan is an Auto-
matic Demonstration Program. It can be used to fully
demonstrate and test the operation of the fan.
To enter the demonstration program:
1. Turn off for at least three seconds. This will
clear the fan memory ready for programming.
2. Turn on.
3. Immediately operate the buttons in the following se-
quence:
FAN - LIGHT - FAN - LIGHT - FAN
A multi-tone signal will verify the start of the test program
which proceeds as follows:
• Lights slowly increase to full intensity.
• Fan accelerates to speed three with audio tones.
• Light dims to half intensity.
• Fan accelerates to full speed with audio tones.
• Fan reverses at full speed with audio tones.
• Fan operates at full speed.
• Fan power is reversed with audio tones.
• Fan turns off with audio tones (blades coast for a short
time).
• Lights turn off.
The complete cycle lasts slightly over one minute. It will
continue to repeat until the is turned off for more
than three seconds, cancelling the program.
The button is normally left in the on position. Always turn the
power off during cleaning or servicing the fan and during thunderstorms. It
is also used to exit or enter additional programs.
POWER must be left on to retain a previously set fan speed or light level.
INTELI•TOUCH OPERATION ♦SPEED CONTROL
R
FAN CONTROL
ON - OFF:
A momentary press
of the FAN button
CHANGE SPEED:
Press and hold FAN
button longer than
one second
There are six individual speed settings for the fan; each speed is indicated by
an audible tone of increasing pitch.
To select the desired fan speed:
1. With fan off, press and hold the button labeled . The fan blades
will start rotating at the slowest speed, and will increase in steps.
2. Release the button when the desired speed is reached.
The fan speed is now in memory and will automatically come on at the same
speed each time the button is used. To maintain this level of speed,
turn the fan on by pressing less than one second. To lower speed,
turn fan off, then on by pressing and holding the button until the
desired speed is reached. When the fan is on, you may increase the speed by
pressing and holding the button until the desired speed is reached,
then release it. INTELI•TOUCH OPERATION ♦REVERSING AIRFLOW
The direction of airflow can be changed from downward to
upward or from upward to downward.
To reverse the airflow:
1. Make sure the is on.
2. Press the button.
Note: A four-toned signal indi-
cates the command was accepted
by the fan. A few seconds later
the fan will slow to a stop and
then reverse direction.
INTELI•TOUCH OPERATION ♦LIGHT
R
LIGHT CONTROL
ON - OFF:
A momentary press of
the LIGHT button
CHANGE BRIGHTNESS:
PRESS AND HOLD
LIGHT BUTTON
LONGER THAN ONE
SECOND
To turn the lights off and on, press and release the button for less
than one second.
To vary the light brightness:
1. With lights off, press and hold the button. After one second the
lights come on at their lowest level and gradually become brighter.
2. Release the button when the desired brightness level is reached.
The brightness level is now in the fan memory and will automatically come
on at the same brightness the next time the button is used. To
maintain this level of brightness, press the button for less than
one second. To lower the brightness, turn the lights off, then press and hold
the button until the desired brightness level is reached. When the
light is on, you may increase the brightness level by pressing and holding
the button until the desired level is reached, then release it.
AUTOMATIC DEMONSTRATION PROGRAM
R

14
The Light-Minder program automatically turns OFF the fan mounted lights after
two hours.
To enter the Light-Minder Program:
1. Turn the OFF for at least three seconds.
2. Turn the ON.
3. Immediately operate the buttons in the following sequence:
+++
4. A series of tones indicates this command has been accepted.
The fan and light will operate normally using the buttons to turn them on and off.
But, if the lights are left on, they will automatically shut off after two hours. To
cancel the Light-Minder Program, turn the off for three seconds.
INTELI•TOUCH OPERATION ♦SAFE-EXIT®PROGRAM
The Safe-Exit Program gives you about thirty seconds of light when you turn
the lights off, enabling you to exit your home before the lights go out.
To enter the Safe-Exit Program:
1. Turn the off for at least three seconds.
2. Turn the on.
3. Immediately operate the buttons in the following sequence:
+++
After you hear the confirming audio
tones from the fan - immediately press
4. The lights will blink to indicate this command has been accepted.
The lights will stay on for twenty seconds and then begin to dim. After a
total of thirty seconds has elapsed, the lights will be off completely. To
cancel the Safe-Exit Program, turn the off for three seconds.
INTELI•TOUCH OPERATION ♦HOME-SAFE®PROGRAM
The Home-Safe Program makes an unoccupied home appear occupied by turning
the lights on and off at random times.
To enter the Home-Safe Program:
1. Turn the off for at least three seconds.
2. Turn the on.
3. Immediately operate the buttons in the following sequence:
+++
4. A tone and flashing light indicate this command has been accepted.
This program overrides all manual control of lights and fan. The lights will now be
automatically cycled on and off in a controlled sequence as follows: On 1 hour, off
1/2hour, on 2 hours, off 1 hour, on 1/2hour then off 2 hours.
This seven hour pattern will repeat continuously so that a different pattern of
lighting is seen each day of the week.
To cancel the Home-Safe Program, turn the off for three seconds.
INTELI•TOUCH OPERATION ♦FAN-MINDER™PROGRAM
The Fan-Minder feature will add to your comfort when used in the bedroom. The program reduces the
speed of the fan each two-hour interval to compensate for the cooling night air.
To enter the Fan-Minder Program:
1. Turn the off for at least three seconds.
2. Turn the on.
3. Immediately operate the buttons in the following sequence:
+++
4. The fan controller will respond with three descending tones. A timer is now initiated and the fan
will reduce one speed for each two-hour interval. The fan will not, however, descend below the
second lowest speed.
To cancel the Fan-Minder Program, turn the off for three seconds. You may increase the fan
speed by pressing and holding the button until the desired speed is reached, then release it.
The fan will again reduce one speed for each 2 hour interval.
INTELI•TOUCH OPERATION ♦LIGHT-MINDER®PROGRAM
Note: Both Light-Minder and Safe-Exit
programs can run at the same time,
however the dimmer cannot be used,
the light may only be turned ON/OFF.
R

15
TROUBLESHOOTING
Before Requesting Service: Please follow this troubleshooting guide before contacting your dealer for assistance.
Caring for Finishes: For cleaning, a soft brush or lint-free cloth
should be used to prevent scratching the finish. A vacuum cleaner
brush nozzle can remove heavier dust. Surface smudges or an accu-
mulation of dirt and dust can easily be removed by using a mild
detergent and slightly dampened soft cloth. An antistatic agent
may be used, but never use abrasive cleaning agents. These will
damage the finish. Painted and high-gloss blades may be cleaned
in the same manner.
Blades: Wood finish blades should be cleaned with a furniture pol-
ishing cloth. Occasionally, a light coat of furniture polish may be
applied for added protection and beauty.
Never Lubricate this Fan!
The precision motor at the heart of your Casablanca fan features
sealed bearings that are lubricated for life. Do not attempt to oil
the motor.
Changing Light Bulbs
Be sure to turn power to the fan OFF at the wall switch or circuit
breaker before changing light bulbs. Replace bulbs with same type
as removed from the fixture. Each fan is rated for a maximum TOTAL
wattage of lighting.
Exceeding the rated maximum allowable wattage for the fan will
burn out the fan electronics module and void the warranty.
PROBLEM POSSIBLE REMEDIES..
NO FAN OR LIGHT Check main circuit fuses, circuit breakers, or wall switch position. Check all wire connections, making
sure the power is turned off during this inspection.
FAN WOBBLES OR SHAKES Be sure canopy pin is properly set into the slot on the ball
EXCESSIVELY Check the screws holding the blade holders to the fan motor. Tighten as necessary.
Check the angle of the blades to make sure that a blade holder has not been bent during installation.
FAN NOISY DURING Check and tighten light fixture retaining screws, glass shade screws and/or the light bulb(s).
OPERATION Tighten canopy screws and mounting plate assembly.
Tighten the blade to bladeholder screws and blade holders to flywheel.
Make sure all screws in the motor housing are snug, but not overly tight.
Check that the wire nuts inside the canopy and switch housing are not touching the metal parts or
have fallen off the wire splices. Tighten or adjust as necessary.
BREAK-IN PERIOD Let fan run at high speed for two (2) hours
DOES NOT RUN ON If new, “break-in” may be required - run at higher speed for several days
LOW SPEED
LIGHTS FLASH OR BLINK DURING OPERATION OF W-32 WALL CONTROLS/FAN MAY ROTATE OR MAKE AUDIBLE TONES DURING
OPERATION OF THE W-11 AND W-12 WALL CONTROLS: Normal operation.
WHEN AC POWER IS TURNED ON FOR THE FIRST TIME, THE LIGHTS OPERATE NORMALLY, BUT W-32 WALL CONTROL OPERATION IS
REVERSED: FAN BUTTON OPERATES THE LIGHTS; LIGHT BUTTON OPERATES THE FAN: Reverse the 2 black and white striped wire
connections.
FAN OR LIGHTS APPEAR TO OPERATE BY THEMSELVES (CHANGING SPEED OR INTENSITY), WALL CONTROL OPERATION IS INTER-
MITTENT: Check AC supply for irregularities, (noise spikes, fluctuations, or failure); or circuit board assembly.
INTELI•TOUCH
R
For questions or to locate the nearest
Casablanca Authorized Service Center
call toll free:
1-888-227-2178
or visit us on the web at:
www.CasablancaFanCo.com

©COPYRIGHT 2000 CASABLANCA FAN COMPANY • U.S. PATENT PENDING PRINTED IN ROC
761 CORPORATE CENTER DRIVE • POMONA, CA 91768
TOLL FREE: 888-CASA-1ST (227-2178)
www.CasablancaFanCo.com