Case IH Luxxum Operator's manual

Luxxum
Quick Instruction
This booklet gives a brief overview of
the most important controls.
The quick instruction is not a
substitute for the operator´s
manual! To operate the vehicle
follow the instructions in the
operator´s manual!
Case IH
Luxxum
Date:
08.01.2018
Language:
English

2
Cab
1-4
6
7
8
910
11
12
13
14
15
16
-
19
5
20
21
22

3
1. Heating switch for Front/Rear Screen
2. Heating switch for Rear mirrors
3. Rear Mirror Adjustment
4. Trailerbrake test switch
5. Shuttle Lever + Neutral Button
6. Dashboard (Speed, gear settings, etc…)
7. Front Wiper, Indicator
8. Multicontroller armrest
9. Electrical Joystick (with transmission
functions) for remotes (front loader)
10. Mechanical Front Loader Joystick (NOT
together with electrical, arrow shows only
position, lever is not in picture)
11. Hazard Light
12. Display - Home/Enter, Up/Down
13. Tractor light main switch
14. Battery Main switch
15. AC/Heating Control Unit
16. Rear Screen Wiper/Washer
17. Auxiliary Light Switch
18. Front axle suspension switch
19. Front axle manual leveling
20. Work Light Panel
21. Radio
22. Transport/Field group lever

4
Controls
1
2
11
10
9
8
7
6
5
4
3
26
20
19
18
17
161514
13
25
24
23
22
21
27
28
29
12

5
1. Mechanical rear remotes
2. Multicontroller
3. Electronical remotes (f/r)
4. Mechanical lever for front remotes
5. Toggle switch f/r remotes
6. Encoder for remote settings (timer, flow)
7. Hand throttle
8. Shiftpoint adjustment
9. Transmission programming
10. Shuttle reactivity
11. Maximum working depth
12. Draft control encoder
13. Constant engine speed switch +
adjustment
14. 4WD switch
15. Differential lock
16. Manual switch for rear hitch raise / lower
17. EDC master switch
18. PTO soft start
19. EDC controls
20. Signal socket
21. ISO-BUS cabIN socket
22. Power socket
23. Eco / Normal pto lever
24. 540 / 1000 PTO lever
25. Front & rear pto switch
26. Screw type 12V socket
27. power socket
28. EFH panel
29. Slip control

6
First steps
When starting your tractor make sure:
1. Depress clutch pedal You can only
start the engine when the clutch is fully
depressed.
2. Shuttle lever has to be in neutral position
3. Activate hitch and hydraulic functions
up: remote valves active
center: remotes and rear hitch
deactivated
down: remotes and rear hitch
activated
1
2
3

Multicontroller
Multicontroller(Backside)
Shift
Multicontroller
(version mechanical remotes)
Constant engine speedPowerClutch
Transmission
modes
Remote Valve
F1/R4 –R3
Remote Valve
F1/R4 –R3 Powershift
gears
Rear Hitch
up/down,
quick
penetration,
stop
Power
Shuttle
(Version: electro-hydraulic remotes)

8
Dashboard
Rear/Front
DiffLock
4WD
Rear/Front
PTO
Indicator
Trailer I/II
High Beam
Side lights
STOP
Turn
left
WARNING
Front axle suspension
Hand
brake
Trailer Brake
Brakes not
latched
Eng. Oil
pressure
Grid
heater
Constant
ERPM
Turn
right
Alternator
charging
Remotes
Low fuel
level
Rear AUTO
PTO

9
Display
Driving
direction
Current gear
gear shift
mode
Delta
Powershift
gear
Ground speed
•rear pto speed
•rear hitch position
•front pto speed
•EFH pressure
•EFH position
•slippage (with radar o)
•Ad Blue status
•odometer
•area worked
•area per hour
•service message
•remote valve values
•battery voltage
•air brake pressure
•error message
1 = Home / Enter
2 = Up / Down
2
1

10
GEAR SHIFT Modes
Gear match: (standard setting)
•Automatically adapting the
powershift steps that fits
best to the present speed
while up- & downshifting
ranges.
Auto FIELD:
•Only PS-steps in a range
will be shifted automatically
Auto TRANSPORT:
•All gears will be shifted
automatically
Manual:
•Gears will be shifted with
+/- completely manually

11
Automatic Power Shift Function:
Choose FIELD or TRANSPORT Automode with button on
the Multicontroller.
Auto FIELD:
Only PS-steps in a range will be shifted automatically.
Auto TRANSPORT:
All gears will be shifted automatically.
Gear shifting points can be adjusted according to engine
speed and load by moving the right hand throttle (5) up
or down.
Power Mode: PS-step shifting @ higher rpm
Mid Power Mode: between Power and Eco
Eco Mode: PS-step shifting @ low rpm

12
Transmission programming
There are 4 different modes to program for
proper driving:
ActiveClutch
Delta (Memory shuttle)
Powershift steps in Auto Filed mode
Standard gear
To start the transmission programming
procedure push the PROG button on the
armrest.
1. Press!
1. ActiveClutch
Brings the tractor to a stop, only by pressing
the brake pedal without using the clutch.
2. Delta PROG
To achieve the desired forward/ reverse speed
there is a DELTA (Memory shuttle) available
which allows you to program from
+3 to -3 (powershift gears) according to the
forward powershift gear.
Tractor does not shift groups!
To adjust press +/- on MC.
2. Press!

13
3. Press!
3. Powershift steps in Auto Field mode
Adjusting the bandwidth of powershift
gears that can be used automatically in the
field.
To adjust press +/- on MC.
4. Standard gear
Setting the standard gear that is
automatically engaged after starting the
engine. STDG will always be engaged after
vehicle comes to standstill.
To adjust press Shift together with +/- for
the main gear and only +/-for the PS
gear.
4. Press!
5. Press! Done

How to drive…
1. Choose Field or Road range.
2. Select driving direction
3. Realease the clutch tractor will start in the standard gear!
4. Shift group 1 to 4 with Shift together with +/-or PS-steps with
just +/- on the MC.
5. To stop the tractor again use the clutch or Powerclutch button on
the MC!
Gearmatch is always active after starting the engine Change
the transmission mode with the button on the Multicontroller!
Powerclutch
1
2
3
4
5

15
Transmission features
Anti-Jack-Knifing
By pushing Shuttle FWD
button in this situation,
automatic gear-shifts
can be inhibited and
tractor is driving
smoothly as well down
a hilly curve.
Shuttle reactivity
How quickly tractor will shuttle from forward to reverse. The option
to have a high reactivity setting during loader work for near-instant
shuttling, or may wish for a low reactivity setting during field work
for a smoother ride.
1 –High reactivity - loader
2 –Standard reactivity - transport
3 –Low reactivity - field

16
Front axle
Manual leveling up & down
Press 3 sec.
The suspended axle
offers the possibility to
raise/lower the height of
the tractors front-end
with a switch.
Axle capacity of 3.500 kg
The suspension can be
turned off between 0-12
km/h.
Above 12 km/h active
suspension automatically
engages.
Button allows adjustment
of suspension setting to
three different levels:
soft, normal and
hard.

17
Constant engine speed
Two electronically regulated constant engine speeds can be stored.
This function is particularly helpful when operating with PTO. The
engine speed can conviniently be reduced on the headland by
simply pressing a button on the Multicontroller and increased again
in the same way.
1. CES on / off
2. Adjust CES 1: hand throttle at idle, short press up/down
adjusts in10 rpm steps, constant pressing adjusts in 100 rpm
steps.
3. Change to CES 2 and adjust like before.
4. Work with CES (CES on): hand throttle above 1000rpm
5. Change between speed 1 and 2. 1
25
3
5

18
PTO
AUTOMATIC STOP/RUN OF PTO
SHAFT WHEN IMPLEMENT IS
LIFTED/LOWERED
1. Turn on pto
2. Switch on auto pto.
3. Drive off and start working.
1
2
ADJUSTMENT OF ON/OFF POINTS
Adjust the shut off and turn on points in accordance to the lifting height of the rear hitch:
1. Press the auto pto switch for more than 3 seconds.
2. Lift or lower the rear hitch to the desired position (here 30% lifting height) where the pto
should stop turning. u = up
3. Press auto pto switch shortly.
4. Lift or lower the rear hitch to the desired position (here 65% lifting height) where the pto
should start turning. d = down
5. Press auto pto switch shortly.
6. Finished. End

19
Mechanical valves
1. Up to 3 rear remotes controlled with levers on
side console.
Positions: raise / neutral / lower / float / lock
2. Joystick for front loader operation controls two
front remote valves.
Positions: raise/neutral/lower/float
Detent on float position available.
3. Oil flow volume can be adjusted for all remote
valves by turning the designated plastic wheels.
1
2
3

20
Electrical valves
1. 2 remote valves on Multicontroller,
default: rear remotes.
2. 2 remote valves on joystick,
default: front remotes (front hitch, front
loader).
3. Toggle switch: changes operation of rear
and front valves between Multicontroller
and joystick.
4. Push/turn switch to adjust
timer and oil flow values. see in
dashboard.
1
23
34
activation of float (pressure
release) for remotes operated on
Multicontroller