Casella STORM Guardian Service manual

1
STORM Guardian
Operator’s Handbook
COPYRIGHT
The copyright in this document which contains proprietary information is vested in
CASELLA. The contents of this document must not be used for purposes other
than that for which it has been supplied or reproduced or disclosed wholly or in part
without the prior written permission of
CASELLA
CASELLA
Regent House
Wolseley Road
Kempston
Bedford
MK42 7JY, U.K.
Phone: [phone]
Fax: [phone]
E-mail [e-mail]
Web: www.casellagmeasurement.com
Casella Inc.
415 Lawrence Bell Drive, Unit 4
Buffalo,
NY 14221
USA
Toll Free: [phone]
Tel: [phone]
Fax: [phone]
Email: [e-mail]

2

3
Introduction
Casella Tipping Bucket Rain Gauges are reliable and extremely robust devices. When
paired with a Casella LOG 8 telemetry data logger they have the ability to take
measurements from a single or a multi-parameter sensor at regular intervals, and
stores this data in internal memory. This instrument will from here on in be referred to
as STORM Guardian.
Using GPRS or GSM telemetry, the LOG 8 contacts a data collection system, typically
once per day, and transfers data to the data collector.
The LOG 8 can also be configured for alarms with user-specified set points. When a
measurement exceeds a set point, the LOG 8 contacts the data collector and transfers
data along with an alarm message. The alarm message is typically forwarded by the
data collector as an email or an SMS message.
The LOG 8 manages power to both the modem and sensors. An external battery is
needed, in the range of 3.6V to 20V. This battery charges and internal rechargeable
cell (an HLC) which will run the system for a short period during battery changing.
The battery and sensor connect via a 6-way screw connector, which is protected by a
piercable sealing grommet.
Figure 1: The Tipping bucket rain gauge with the outer cover removed.

4
Principle of Operation
The rain gauges comprise a light weight injection moulded plastic divided .tipping
bucket. assembly with stainless steel pivot pins that rest upon stainless steel pins in
the support assembly. The use of pins produces a rolling rather than pivoting motion
when the bucket tips, which reduces the likelihood of friction.
Rain collects in one side of the bucket, which tips once a predetermined volume of
water has been collected. The tipping action discharges the collected water and
positions the other side of the bucket under the discharge nozzle ready for filling.
Each time the bucket is tipped, a magnet within the bucket moulding closes a reed
switch in the support assembly. The use of a sealed reed switch, capable of indefinite
operation, ensures the instrument has a long working life. Each contact closure pulse
represents a discrete amount of rainfall appropriate to the instrument’s calibration.
These tipping pulses may be counted or recorded using a variety of methods, as
described in Chapter 6.
The tipping bucket mechanism is mounted inside the body on a cast aluminium-alloy
base, incorporating a built-in spirit level to facilitate correct positioning. Both body and
funnel are manufactured from aluminium alloy, with an accurately machined septum
ring with an aperture of 400 cm2. (200cm2 version is now also available) The
measurement accuracy for the various tip sizes is shown in Figure 2.
Figure 2: Accuracy of 0.1 mm, 0.2 mm and 0.5 mm tip versions

5
Construction
The rain gauge is manufactured entirely from non-corrosive materials. The base and
septum ring are cast in Aluminium Alloy LM25, heat treated and protectively coated.
The outer ring and funnel are fabricated from aluminium alloy sheet and again
protectively coated.
Stainless steel mesh is employed to protect the inlet and outlet ports from the ingress
of foreign bodies.
Preparation for use
Each instrument is delivered ready calibrated to indicate either 0.1 mm, 0.2 mm or 0.5
mm of rainfall each time the bucket tips.
It is also recommended that the rain gauge be installed in a location or enclosed
compound away from access by the general public.
Prepare a reasonably level site for the rain gauge paying due regard to the following
points:
•No object should be nearer than four times its own height from the bucket.
•Do not locate the rain gauge in a hollow or on top of a hill.
•Tall buildings or belts of trees can cause turbulence and gusts which can
increase or decrease the rain collected.
•The surrounding soil should be capable of allowing the discharged water to
drain away freely.
Warning !
The septum ring has a sharp edge and should be treated with care
whenever handling the instrument.
4.1. Standard Single Output Non-Heated Version

6
1. Release the two catches securing the outer cover to the base and then carefully lift
off the cover.
2. Feed a suitable length of 2 A, 2-core cable, through the grommet.
3. Connect the instrument end of this cable to the terminal block provided on the
underside of the base unit for the output signal.
4. Connect the free end to the counting device, see Figure 3 and Chapter 6
5. Go to Section 4.3.
4.2 Standard Dual Output Non-Heated Version
1. Release the two catches securing the outer cover to the base and then carefully lift
off the cover.
2. Feed a suitable length of 2 A, 4-core cable, through the grommet.
3. Connect the instrument ends of two of the cores to adjacent terminals connected to
the white leads on the block provided on the underside of the base unit for the
output signals.
4. Connect the free ends of these cores to the first counting device (see Figure 3 and
Chapter 6).
5. Connect the instrument ends of the other two cores to the other adjacent terminals
connected to the white leads on the block.
6. Connect the free ends of these cores to the second counting device (see Figure 3 and
Chapter 6).
7. Go to Section 4.3.
4.3 General
1. Seal all weather connections using a silicone rubber compound.
2. With the base plate mounted in its correct location on site, adjust the three levelling
screws until the built-in spirit level indicates that the unit is level.
3. Once the unit is level secure the locknuts.
4. It is advisable to secure the base unit permanently to a firm foundation using the
two holding lugs provided.
These accept either 9.5 mm or 3/8" rawl bolts.
Do not over tighten the fixings.

7
A restriction, such as an elastic band, may have been fitted to prevent the bucket
from moving during transit.
5. Carefully remove any restriction and check that the bucket pivots freely.
6. Replace the outer cover of standard versions, with the catches engaged in the
cutouts in the base plate.
7. Replace the outer cover of versions that meet the Environmental Agency Framework
Directive, then use the Allen Key to lock the three catches to secure the cover to the
base.
The rain gauge is now ready for operation.
5. MAINTENANCE
Warning !
The septum ring has a sharp edge and should be treated with care whenever
cleaning or handling the instrument.
Periodically check for debris in the funnel and blockage of the inlet and outlet ports. Remove
any debris present and clean the meshes.
The water outlet on the underside of the funnel can be unscrewed allowing the inlet mesh to
be removed and cleaned.
If necessary, bucket surfaces can be cleaned using a mild detergent solution.
6. Counting the bucket tips

8
A variety of devices may be used to count the bucket tips, these include:
•Data Loggers (with contact closure input capability),
•Event counter (a simple LCD counter to indicate bucket tips),
•Chart Recorder,
•Computer data acquisition system.
Consideration should be given to ensure that the counting/logging device used can accept a
contact closure input.
For fast counter inputs, some form of capacitor-resistor filtering may be necessary to reduce
bounce effects in the contact signal.
For details of suitable logging devices please contact the Casella sales department.
Please go through these procedures before you go to site.
6.1 Harvest software
You need to get Harvest software so you can read and configure the F1262.
Install this software from the CD supplied with the logger.
6.2 F1262 System components
The parts shown above are included with each LOG 8
The LOG 8 uses requires GSM antenna connected to the SMA connector on the
end cap

9
To read and configure the F1262 locally, you will need one of these communications
cables:
6.3 SIM fitting
Fit a SIM by loosening the two screws securing the SIM cap and draw
the cap away.
CBL-TAD-EXT local
serial cable (RS-232)
CBL-TAD-USB local
serial cable (USB)

10