Casio SE-S10 Operating instructions

Load Memory Protection Batteries and Paper Roll
A) Remove the printer cover
B) Open Battery compart
ment cover
C) Insert 2 new “AA”type batteries
into the compartment
D) Install the supplied 58mm thermal paper roll by lifting up
the platen arm (Push open button) and placing the paper
roll into the printer well. Close the cover firmly.
1
Initialize Your Cash Register
2
A)
Insert the supplied key and turn
to the “OFF”position. B)
Plug the power cord into the AC outlet and wait for
the instructional messages to print.
IMPORTANT Be sure that the plus (+) and minus (-) ends of the batteries
are facing in the directions indicated in the illustration inside the
battery compartment.
To prevent losing all of your settings and sales
data, we recommend you install the two memory
protection batteries.
Choosing the Language
3
A) For English select the following:
Please also refer to printout instructions from the cash register
To set for
journal
printing
:
To set for receipt printing
:
A)
Turn key to the PGM position
B)
Perform steps below.
Setting Date and Time
4
A)
Input date and time as indicated on the printout chit on the cash
register
A) Turn key to the
Z position
B) Perform the following sequence
Note: This operation automatically sets correct tax
rates, rounding, and receipt formats to Australian
standards.
Setting for Australian Standards
6
6
A) Turn key to the PGM position
position
B) Press
To enable
C) Press Press departments as required
D) Press
If using shift departments
otherwise skip this step
To disable use same sequence except use in place of
Australian Quick Programming Guide
Casio SE-S10 (please refer to the supplied “User Manual”for further information)
“
14
Flash Report
A flash report
is a useful tool
to monitor how much money has been taken throughout the trading day
.
A) Turn Key to the Xposition
B) Press
Electronic Journal Report
The electronic journal records most operations that are performed at the cash register. Data can be printed out
if a hard copy is required and it is also possible to designate a read range by date and or consecutive number.
(Please refer to the user manual for additional information on this feature)
Note: This operation will print and reset the Electronic Journal print only is performed from X mode please refer User Manual for more
details
.
The following operation will print the end of day financial report.
Note: Using XMode will print only while ZMode will print and reset the figures ready for the next trading day.
16
Daily End of Day Report
15
A) Turn Key to the Zposition
B) Enter 58
A)
Turn key to the PGM position
B)
Perform steps below.
Setting GST to Departments
7
5
Printer switch for receipt or Journal

ó Receipt message 1st line
YOUR RECEIPT
ó Receipt message 2nd line
THANK YOU
ó Receipt message 3rd line
CALL AGAIN
ó Receipt message 4th line
ó Receipt message 5th line
Australian Quick Programming Guide
Casio SE-S10 (please refer to the supplied “User Manual”for further information)
Setting descriptors to PLU’s
11
A) Turn Key to PGM mode
B) Press
C) Press
D) Enter
E) Press
The following sequence will program the descriptor “DAIRY”to PLU
number 1.
Linking PLU’s to Departments
12
Linking PLU’s to departments is only required if you are using PLU’s.
This process aids end of day reporting by grouping products (PLU’s)
with departments
.
A) Turn Key to PGM mode
B) Press
C) Enter
D) Press
The SE-S10 contains 20 departments, 5 are located on the keyboard and
an additional 15 are accessible using the department shift function.
Prices can be set to departments if required or entered manually from
with
in the sale.
B) Press
D) Key price then press department key
A) Turn Key to PGM mode
Note: Press dept shift once to access departments 6~10 or twice
for 11~15 e
tc.
IMPORTANT: Never
use decimal point key when imputing
price.
C) Press Dept Shift if programming shift departments
otherwise skip to step D
A) Turn Key to PGM mode
B) Press
C) Press
D) Enter
E) Press
The SE-S10 does have the option of 500 PLU’s. A PLU lookup function is
provided should you decide to use PLU’s on this register.
E) Press
Setting Descriptors to Departments
10
A) Turn Key to PGM mode
B) Press
D) Enter
E) Press
C) Press
The following procedure will program the descriptor “DAIRY”to Department number 1.
Programming Receipt Message
13
You can program receipt message text at
the top of the receipt. Up to 5 lines of text
can be programmed.
Receipt message sample
Links PLU1 to
Department 4
This procedure sets $1.00 to PLU1.
Note: button is used to add a space or to lock a character if more than one character is used from a single key in
succession. An example of how this button is used is shown in section 13 - “Receipt Text Programming”.
Setting prices to Departments
8
Setting prices to PLU’s
9