TL-LD710K
Rubber base for Sharp Aero
For posts with a more acute angle, use the
rubber base for Sharp Aero.
OPTION
Always charge the product before use.
Attach the light securely to the seatpost.
Automatic battery-saving function:
When the remaining battery power is low, the lighting mode switch
starts flashing and the lighting mode changes to flash. The Kinetic
function is disabled when the remaining battery power is low.
Charge the light as soon as possible.
ENG
Copyright© 2017 CATEYE Co., Ltd.
TLLD710K-190517 6
HOW TO CHARGE
HOW TO USE
1
HOW TO MOUNT
2
3
1
2
1
2
Seatpost
Click Lighting mode switch
Press and hold ON OFF
Low
Approx. 5h*
High
High
High
Flashing
Approx. 30h*
Rapid
Approx. 16h*
*The stated runtime of each mode exclude the Kinetic function, and the
actual runtime may vary when the Kinetic function is enabled.
*
As a reference, when the Kinetic function is enabled 60 times / hour, the
runtime will be approx. 3 hours in Low mode, approx. 7 hours in Flashing
mode, and approx. 5 hours in Rapid mode.
Kinetic function:
When deceleration of the
bicycle is detected, the light
will turn on in the High mode
for approximately 2.5 seconds
regardless of the lighting
mode selected. The light will
remain on in the High mode
as long as deceleration is
detected.
WARNING!!!
• Before your trip, please make sure the light is
securely attached and lights up.
Do not use a damaged rubber band.
•
Always pay attention to the remaining battery power
by checking the indicator periodically while using.
CAUTION!
• This light detects deceleration through the use of
acceleration sensor. Please note that activation of
the Kinetic function depends on the degree of
deceleration, the light may not react or the
reaction may be delayed.
• Stop your bicycle to operate the switch.
• Keep the light away from children.
• Charging, discharging, and storing in high
temperatures will cause the rechargeable battery
to deteriorate faster. Do not place the light inside
a vehicle or near a heater.
• This unit is not totally waterproof. Please wipe
and dry it completely after using in rain.
Otherwise, it may cause failure.
• If the light unit or parts become dirty with mud,
etc., clean with a soft cloth which is moistened
with mild soap. Never apply paint thinner, benzine
or alcohol; damage will result.
PRECAUTIONS ON CHARGING
• We recommend using 500+mA (USB2.0) USB
battery charger.
• Avoid charging in direct sunlight or in a vehicle
parked under direct sunlight, and make sure to
charge only when the ambient temperature is
between 5 and 40°C (41°F and 104 °F).
• Before charging, be sure that no dust or other
foreign objects attach to the USB plug.
•
Do not subject the light to vibrations while charging.
• When your PC is in sleep state, the unit cannot be
charged.
• Once charging is complete, be sure to disconnect
the USB plug.
•
Charging and lighting times are approximate values,
and will vary by environmental and user conditions.
• If the illumination time is significantly reduced
even after proper charging, the rechargeable
battery may be nearing the end of its service life.
Dispose of the battery as described in “PRECAU-
TIONS ON DISPOSAL”.
STORAGE PRECAUTIONS
Cool and dry storage is recommended.
For long period storage, it is important to charge the
battery 30 minutes every 6 months.
PRECAUTIONS ON DISPOSAL
When disposing of the light unit, dispose of it
according to local regulations.
Manual
Before using the light, read this
manual thoroughly and keep it for
future reference.
Light unit USB cable
(MICRO USB)
Rubber band
(Large/Small)
USB cable
To PC or USB battery charger
Charging
Charging is completed
Standard
charging time Approx. 2 h
(USB 2.0)
Switch (Indicator)
Rubber band
