CB2 Finn Lounger User manual

Made in China - r08 Page 1 of 3
finn LOUNGER
1
hardware
components
tools required
Thank you for purchasing the Finn Lounger. This page
lists all the contents included in the box. Please take
the time to identify the hardware as well as the
individual components to this product. As you unpack
and prepare for assembly, place the contents on a
carpeted or padded area to protect them from
damage.
Note: 2 people are required to safely assemble this product.
Missing hardware?
Please call 800.606.6387 for replacements.
A. Insert 1 barrel screw and 1 threaded bolt into
left and right side frames as shown. Secure, but
do not over tighten, the barrel screws with a
phillips head screwdriver.
B. Using a screwdriver, remove set screws from
each barrel nut and set aside. Insert barrel nuts
into the back frame as shown. Align the hole on
the side of each barrel nut with the hole on the
end of the back frame.
2 - side frames
(1 left, 1 right)
1 - back
frame
1 - front
crossbar
1 - center
rail
1 - slat roll
2 - barrel
nuts
allen wrench
left and right
side frames
Customer Service 800.606.6252 | Latest instructions available at www.cb2.com
1 - matress
2 - threaded
bolts
8 - screws
2 - hex
nuts
4 - hex
bolts
2 - barrel
screws
2 - connectors
hex wrench
back
frame
A
B
2 - allen
bolts
phillips head screwdriver
(not included)
( We recommend the use of hand tools instead of power tools )
B
2 - caps
1 - support
leg
1 - support
leg bolt
5 - pads

Insert connector into front crossbar as shown.
Fit bolt of side frame into front crossbar.
Loosely attach with 1 hex nut using a hex
wrench as shown.
finn LOUNGER
Made in China - r08 Page 2 of 3
23
4
NOTE: Do not fully
tighten the bolt
left side
frame
front
crossbar
left side
frame
left side
frame
NOTE: Do not over
tighten the screw
Customer Service 800.606.6252 | Latest instructions available at www.cb2.com
center rail
A. Loosely attach center rail to left side frame
with 1 allen bolt using an allen wrench.
B. Fit dowels of support leg into
corresponding hole of center rail and secure
with 1 support leg bolt using a screwdriver.
With the assistance of another
adult, fit barrel screw of left side
frame into corresponding hole of
back frame. Secure barrel screw
by inserting a set screw into the
barrel nut. Loosely secure set
screw, using a screwdriver. Make
sure set screw securely engages
the barrel screw.
B. Attach 1 cap as shown.
C. Loosely attach bracket of back
frame to left side frame with 2 hex
bolts as shown using a screwdriver.
Do not over tighten the bolts.
A
A
B
C
back frame
C
support
leg
A
B
A

CLEANING AND CARE
Clean surfaces with a dry or damp cloth. Do not use
abrasive cleaners. Do not use furniture wax or polish as
the unit is finished with a protective clear lacquer. Wipe
up spots and spilled immediately. Please keep Finn
Lounger out of direct sunlight to prevent the matress
cover from fading.
finn LOUNGER
Made in China - r08 Page 3 of 3
6
7Place matress onto assembled unit.
Assembly is now complete.
Lay slat roll onto assembled unit with fabric straps
facing down. Secure with 8 screws using a
screwdriver as shown.
slat roll
NOTE: Make sure straps
are facing down as shown.
Customer Service 800.606.6252 | Latest instructions available at www.cb2.com
5
right side
frame
A. Repeat steps 2-4 for right
side frame. At this point, fully
tighten all bolts and screws.
B. Adhere 1 pad onto each foot
of assembled unit as shown.
Press firmly to secure.
pad A
B