CB2 GLOSS User manual

Made in Vietnam - r05 Page 1 of 4
gloss TALL DRESSER
assembly hardware
components
tools required
Thank you for purchasing the Gloss Tall Dresser.This
page lists all the contents included in the box. Please
take the time to identify the hardware as well as the
individual components to this product. As you unpack
and prepare for assembly, place the contents on a
carpeted or padded area to protect them from damage.
Note: 2 people are required to safely assemble this product.
Missing hardware?
Please call 800.606.6387
for replacements.
(We recommend the use of hand tools instead of power tools)
Customer Service 800.606.6252 | Latest instructions available at www.cb2.com
phillips head screwdriver
32 - screws 12 - bolts 12 - wood
dowels
12 - flat
washers
12 - spring
washers
1 - bottom
panel
1 - top
panel
2 - side panels
(1 left, 1 right)
8 - drawer sides
(4 left, 4 right)
4 - drawer
fronts
1 - back
panel
4 - drawer
backs
4 - drawer
bottoms
1 - middle
panel
4 - small
screws
4 - large
screws
2 - wall
straps
4 - mounting
brackets
4 - plastic
anchors
mounting hardware

gloss TALL DRESSER
Made in Vietnam - r05 Page 2 of 4
12
Insert 4 wood dowels into middle panel as
shown. Fit dowels of middle panel into
corresponding holes of left and right side panels.
Secure each side panel with 2 bolts, 2 spring
washers and 2 flat washers. Secure, but do not
over tighten, bolts with a phillips head
screwdriver.
34
Insert 4 wood dowels into bottom panel as
shown. Fit dowels of bottom panel into
corresponding holes of side panels, and secure
with 4 bolts, 4 spring washers and 4 flat
washers.
With assistance of another adult, position unit
upright. Fit back panel into corresponding
grooves of side panels as shown.
NOTE: Do not
over tighten bolts
left side
panel
bottom
panel
back panel
NOTE: Make sure grooves
of left and right side panels
are facing each other during
assembly as shown
right side
panel
A. Insert 2 wood dowels into left and right side
panels as shown.
B. Fit dowels of side panels into corresponding
holes of top panel. Secure each side panel with
2 bolts, 2 spring washers and 2 flat washers.
A
B
top panel
Customer Service 800.606.6252 | Latest instructions available at www.cb2.com

gloss TALL DRESSER
Made in Vietnam - r05 Page 3 of 4
56
78
A. Attach left drawer side to drawer front with
2 screws as shown. Secure, but do not over
tighten, screws with a screwdriver.
B. Insert drawer bottom into grooves of drawer
side and front as shown.
Attach right drawer side to drawer front and
back with 4 screws as shown.
Repeat assembly steps 5-7 for remaining 3
drawers.
Attach drawer back to left side drawer with 2
screws as shown.
A
B
NOTE: Do not
over tighten
the screws
left drawer
side
drawer
front
drawer
bottom
drawer
back
right drawer
side
Align drawer glides of each drawer with
corresponding drawer glides of assembly as
shown. Firmly push drawer into assembly until
the glides are securely engaged.
Assembly is now complete.
Customer Service 800.606.6252 | Latest instructions available at www.cb2.com
NOTE:
Make sure glides are
pulled out of the case, and
ball bearings are at the front of
the extended glides

gloss TALL DRESSER
Made in Vietnam - r05 Page 4 of 4
cleaning & care
Clean surfaces with a dry or damp soft cloth. Do not use
abrasive cleaners. Do not use furniture wax or polish as
the unit is finished with a protective clear lacquer.
NOTE: If you are unsure about your wall type or what mounting method you should use,
consult a qualified professional or your local hardware store.
For added safety and stability, it is recommended that the wall mounting hardware be installed. For
safe mounting, it is essential to use wall anchors appropriate to your wall type (i.e. plaster, drywall,
concrete, etc.). Mount to wood studs whenever possible.
A) Attach 2 mounting brackets to top of unit using 2 small screws per bracket.
B) Determine the final location of unit. Mark position on the wall, approximately 2" below each
mounting bracket on the back of the unit.
C) Drill a hole in the wall stud. If a wall stud is not available, drill a hole in the wall that is slightly
smaller in diameter than the anchor. Gently tap the plastic anchor until the flange of the anchor is
flush with the wall.
D) Attach the mounting brackets to the wall by inserting 2 large screws through each mounting
bracket and into the wall anchor in the wall.
E) Position the unit so the mounting brackets on the back of the unit are aligned with the wall
brackets.
F) Lace one end of each wall strap through corresponding brackets, and into the other end of the
strap.
G) Pull the straps tightly until secure.
Wall mounting assembly is now complete.
wall mounting assembly
A
CD
F
Customer Service 800.606.6252 | Latest instructions available at www.cb2.com