CB2 LINEAR User manual

Made in Vietnam - r05 Page 1 of 4
linear NIGHTSTAND
hardware
tools required
Thank you for purchasing the Linear Nightstand. This
page lists all the contents included in the box. Please take
the time to identify the hardware as well as the individual
components to this product. As you unpack and prepare
for assembly, place the contents on a carpeted or padded
area to protect them from damage.
Note:2 people are required to safely assemble this product.
Missing hardware?
Please call 800.606.6387
for replacements.
1 - top panel
8 - spring
washers
8 - large
bolts
8 - flat
washers
Customer Service 800.606.6252 I Latest instructions available on www.cb2.com
allen wrench
(included)
components
1 - bottom panel
1 - back panel
16 - small
bolts
16 - screws
philips head screwdriver
2 - side panels
(1 left, 1 right)
2 - drawer
fronts
2 - drawer
backs
(We recommend the use of hand tools instead of power tools)
4 - drawer sides
(2 left, 2 right)
2 - drawer
bottoms
4 - legs

Made in Vietnam - r05 Page 2 of 4
Customer Service 800.606.6252 | Latest instructions available at www.cb2.com
1
With the assistance of another adult, carefully
place top panel upside down onto a clean,
padded surface. Fit pre-assembled dowels of left
and right side panels into corresponding holes of
top panel. Secure left and right side panels to top
panel with 2 flat washers, 2 spring washers and
2 large bolts per side as shown. Secure, but do
not over tighten bolts using a phillips head
screwdriver.
NOTE: Do not over
tighten the bolts.
2
3 4
linear NIGHTSTAND
Slide back panel into grooves of left and right
side panels.
back panel
NOTE: Make sure left
and right side panels are
assembled with grooves
facing back as shown
Carefully place bottom panel onto a clean,
padded surface. Attach 4 legs to bottom panel
with 4 small bolts as shown. Secure, but do not
over tighten the bolts using an allen wrench.
bottom panel
bottom
panel
With the assistance of another adult, fit
pre-assembled dowels of left/right side panels into
corresponding dowels of bottom panel. Secure
bottom panel with 4 flat washers, 4 spring
washers and 4 large bolts using a screwdriver.

linear NIGHTSTAND
Made in Vietnam - r05 Page 3 of 4
Customer Service 800.606.6252 | Latest instructions available at www.cb2.com
5 6
7
NOTE: Do not over
tighten the screws
8
Secure drawer front to right and left drawer
sides with 4 screws as shown using a phillips
head screwdriver. Do not over tighten the screws.
drawer
front
“R” drawer
side
NOTE:
Open end
of glide
hardware
“L” drawer
side
Slide drawer bottom into corresponding grooves
of drawer assembly.
drawer
bottom
Fit drawer back onto drawer bottom and align
with corresponding holes of drawer sides. Secure
drawer back to drawer sides with 4 screws using
a screwdriver.
Repeat steps 5-7 for remaining drawer.
drawer
back
drawer
assembly
With the assistance of another adult, position unit
upright. Pull ball bearing glides of assembly all the
way forward. Fit drawer glides of drawer into
corresponding drawer glides of assembly as
shown. Firmly push drawer into assembly until the
glides are securely engaged.
Assembly is now complete.
NOTE: Make sure to
keep drawer level so
as not to damage glides
during assembly
Make sure glides are
pulled out of the case, and
ball bearings are at the front
of the extended glides

linear NIGHTSTAND
Made in Vietnam - r05 Page 4 of 4
Customer Service 800.606.6252 | Latest instructions available at www.cb2.com
cleaning & care
Clean surfaces witha dry or damp soft cloth.Do not use abrasive cleaners. Donot use furniture wax or polish as the
unit is finished with a protective clearlacquer.