CB2 THE WALL User manual

Customer Service 800.606.6252 | Latest instructions available at www.cb2.com
Made in Vietnam - r02 Page 1 of 4
the wall BATH CABINET
Thank you for purchasing The Wall bath cabinet. This
page lists all the contents included in the box. Please take
the time to identify the hardware as well as the individual
components to this product. As you unpack and prepare
for assembly, place the contents on a carpeted or padded
area to protect them from damage.
Note: 2 people are recommended to safely assemble this product.
components
hardware
mounting hardware
tools required
12 - dowels
3 - hinges
4 -plastic
anchors
4 -small
screws
4 -large
screws
12 - bolts 8 - shelf
pins
Missing hardware?
Please call 800.606.6387 for
replacements.
1 - top panel
2 - side panels
(1 left, 1 right)
1 - door
1 - bottom panel 1 - fixed shelf
phillips head screwdriver
(We recommend the use of hand tools instead of power tools)
18 - screws
2 - adjustable
shelves
1 - back panel
4 -mounting
brackets
2 -wall
straps

Made in Vietnam - r02 Page 2 of 4
Customer Service 800.606.6252 | Latest instructions available at www.cb2.com
1
A. Insert 2 dowels into left side panel as shown.
B. Fit fixed shelf onto dowels, and attach to side
panel with 2 bolts. Secure, but do not over tighten
bolts with a phillips head screwdriver.
NOTE: Do not over
tighten the bolts.
fixed shelf
2
3 4
A. Insert 2 dowels into fixed shelf as shown.
B. Fit back panel into corresponding slot in left
side panel.
C. Fit right side panel onto dowels and back
panel, and attach to side panel with 2 bolts.
left side
panel
A. Insert 4 dowels into side panels as shown.
B. Attach bottom panel to assembly and secure
with 4 bolts.
A. Insert 4 dowels into side panels as shown.
B. Attach top panel to assembly and secure with
4 bolts.
the wall BATH CABINET
right side
panel
back
panel
A
B
C
B
A
A
B
A
B
top
panel
bottom
panel

Made in Vietnam - r02 Page 3 of 4
Customer Service 800.606.6252 | Latest instructions available at www.cb2.com
5
Fit 3 hinges into door as shown and attach with 2
screws per hinge. Secure, but do not over tighten
screws with a screwdriver. 6
7
Attach door to case assembly by aligning holes in
hinges with holes in side panel. Secure each
hinge with 4 screws.
Insert 8 shelf pins at desired shelf heights. Place
each adjustable shelf on pins, making sure shelf
is securely supported by shelf pins.
Assembly is now complete.
the wall BATH CABINET
door
cleaning and care
Clean surfaces with a dry or damp soft cloth. Do not use
abrasive cleaners.
NOTE:
Door can be
installed on
either left or
right side

Made in Vietnam - r02 Page 4 of 4
Customer Service 800.606.6252 | Latest instructions available at www.cb2.com
the wall BATH CABINET
A
C
D
F
For added safety and stability, it is recommended that the wall mounting
hardware be installed. For safe mounting, it is essential to use wall anchors
appropriate to your wall type (i.e. plaster, drywall, concrete, etc.). Mount to
wood studs whenever possible.
NOTE: If you are unsure about your wall type or what mounting
method you should use, consult a qualified professional or your local
hardware store.
A) Attach 2 mounting brackets to top of unit using 2 small screws per
bracket.
B) Determine the final location of unit. Mark position on the wall,
approximately 2" below the mounting bracket mounted to the back of the
unit.
C) Drill a hole in the wall stud. If the wall stud is not available, drill a hole in
the wall that is slightly smaller in diameter than the anchor. Gently tap the
plastic anchor until the flange of the anchor is flush with the wall.
D) Attach 2 mounting brackets to the wall by inserting 2 large screws
through each mounting bracket and into the wall anchor.
E) Place the unit so the mounting brackets on the back edge are aligned
with the wall brackets.
F) Lace one end of each wall strap through brackets, and into the other
end of the strap.
G) Pull the strap tightly until secure.
Wall mounting assembly is now complete.
Depth adjustment:
Loosen screw A, push hinge arm
forwards or backwards, re-tighten
screw Aand secure screw Bwith
a 1/4 turn clockwise
Height adjustment:
Loosen screw A & B, adjust door
height and re-tighten screws A&B
A
B
123
Side to side adjustment:
Loosen screw A, adjust gap with
screw Band re-tighten screw A
A
B
hinge adjustment
If the doors do not appear square or aligned, loosen or tighten the appropriate screws on each case hinge as
illustrated.
A
B