CB2 LINEAR User manual

(We recommend the use of hand tools instead of power tools)
Made in Vietnam - r05 Page 1 of 5
linear LOW DRESSER
hardware
tools required
Thank you for purchasing the Linear Low Dresser. This
page lists all the contents included in the box. Please take
the time to identify the hardware as well as the individual
components to this product. As you unpack and prepare
for assembly, place the contents on a carpeted or padded
area to protect them from damage.
Note:2 people are required to safely assemble this product.
Missing hardware?
Please call 800.606.6387 for replacements.
1 - top panel
12 - spring
washers
12 - large
bolts
12 - flat
washers
Customer Service 800.606.6252 I Latest instructions available on www.cb2.com
allen wrench
(included)
components
1 - bottom panel
1 - back panel
20 - small
bolts
32 - screws
philips head screwdriver
1 - left side
panel
1 - partition 1 - right side
panel
4 - drawer
fronts
4 - drawer
backs 8 - drawer sides
(4 left, 4 right)
4 - drawer
bottoms
5 - legs
4 - wall
brackets
4 - large
screws
4 - plastic
anchors
4 - small
screws
mounting hardware
2 - wall
straps

Made in Vietnam - r05 Page 2 of 5
Customer Service 800.606.6252 | Latest instructions available at www.cb2.com
1
With the assistance of another adult, carefully
place top panel upside down onto a clean,
padded surface. Fit pre-assembled dowels of left
and right side panels into corresponding holes of
top panel. Secure left and right side panels to top
panel with 2 flat washers, 2 spring washers and
2 large bolts as shown. Secure, but do not over
tighten bolts using a phillips head screwdriver.
NOTE: Do not over
tighten the bolts.
top panel
2
3 4
linear LOW DRESSER
Fit pre-assembled dowels of partition into
corresponding holes of top panel. Secure partition
to top panel with 2 flat washers, 2 spring
washers and 2 large bolts as shown, using a
screwdriver.
right side
panel
left side
panel
partition
Slide back panel into grooves of left and right
side panels.
back panel
NOTE: Make sure left
and right side panels are
assembled with grooves
facing back as shown
Carefully place bottom panel onto a clean,
padded surface. Attach 5 legs to bottom panel
with 4 small bolts as shown. Secure, but do not
over tighten the bolts using an allen wrench.
bottom panel

linear LOW DRESSER
Made in Vietnam - r05 Page 3 of 5
Customer Service 800.606.6252 | Latest instructions available at www.cb2.com
bottom
panel
5 6
7 8
With the assistance of another adult, fit
pre-assembled dowels of left/right side panels and
partition into corresponding dowels of bottom
panel. Secure bottom panel with 6 flat washers,
6 spring washers and 6 large bolts using a
screwdriver.
Secure drawer front to right and left drawer
sides with 4 screws as shown using a phillips
head screwdriver. Do not over tighten the screws.
Fit drawer back onto drawer bottom and align
with corresponding holes of drawer sides. Secure
drawer back to drawer sides with 4 screws using
a screwdriver.
Repeat steps 6-8 for remaining drawers.
Slide drawer bottom into corresponding grooves
of drawer assembly.
drawer
front
NOTE: Do not over
tighten the screws
“R” drawer
side
NOTE:
Open end
of glide
hardware
drawer
back
drawer
bottom
“L” drawer
side

linear LOW DRESSER
Made in Vietnam - r05 Page 4 of 5
Customer Service 800.606.6252 | Latest instructions available at www.cb2.com
9
drawer
assembly
cleaning and care
Clean surfaces with a dry or damp soft cloth. Do not use abrasive cleaners. Do not use furniture wax or polish as the unit is
finished with a protective clear lacquer. It is recommended to use coasters to protect surface from heat and water.
TL = top left drawer
TR = top right drawer
BL = bottom left drawer
BR = bottom right drawer
NOTE:
Make sure glides are
pulled out of the case, and
ball bearings are at the front of
the extended glides
With assistance of another adult, insert glides of top left/right and bottom left/right drawer assemblies into
corresponding glides of case assembly. Keeping the drawer level, carefully push the drawer until it is all the way in
the case and glides are securely engaged.
Assembly is now complete.
NOTE: Make sure to
keep drawer level so
as not to damage glides
during assembly

linear LOW DRESSER
Made in Vietnam - r05 Page 5 of 5
Customer Service 800.606.6252 | Latest instructions available at www.cb2.com
safety mounting instructions
For added safety and stability, it is recommended that
the wall mounting hardware be installed. For safe
mounting, it is essential to use wall anchors
appropriate to your wall type (i.e. plaster, drywall,
concrete, etc.). Mount to wood studs whenever
possible.
A) Attach 1 wall bracket to top of unit as shown,
using 2 small screws per bracket.
B) Determine the final location of unit. Mark position
on the wall, approximately 2" below the bracket
mounted to the back of the cabinet.
C) Drill a hole in the wall stud. If the wall stud is not
available, drill a hole in the wall that is slightly smaller
in diameter than the anchor. Gently tap the plastic
anchor until the flange of the anchor is flush with the
wall.
D) Attach the wall bracket to the wall by inserting 2
large screws through the wall bracket and into the
wall anchor in the wall.
E) Place the unit so the wall bracket on the back
edge is aligned with the wall bracket.
F) Lace one end of the wall strap through both
brackets, and into the other end of the strap.
G) Pull the strap tightly until secure. Repeat steps for
remaining brackets and wall strap.
NOTE:
If you are unsure about your wall type or what
mounting method you should use, consult a
qualified professional or your local hardware store.
A
C
D
Fwall
bracket
small
screw
wall
bracket
plastic
anchor
large
screw
wall
strap