Central Machinery 03135 User manual

Compound Sliding Table
ASSEMBLY and OPERATING INSTRUCTIONS
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at http://www.harborfreight.com
For technical questions and replacement parts, please call 1-800-444-3353
Model 03135
®
Copyright © 2003 by Harbor Freight Tools®. All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools .
4” x 4”
Brought To You By Augusta Flint

Page 2
SKU 03135
Specifications
Save This Manual
You will need the manual for the safety warnings and precautions, assembly instructions,
operating and maintenance procedures, parts list and diagram. Keep your invoice with this
manual. Write the invoice number on the inside of the front cover. Keep the manual and
invoice in a safe and dry place for future reference.
Safety Warnings and Precautions
WARNING: When using tool, basic safety precautions should always be followed to
reduce the risk of personal injury and damage to equipment.
Read all instructions before using this tool!
1. Keep work area clean. Cluttered areas invite injuries.
2. Observe work area conditions. Do not use machines or power tools in damp or wet
locations. Don’t expose to rain. Keep work area well lighted. Do not use electrically
powered tools in the presence of flammable gases or liquids.
3. Keep children away. Children must never be allowed in the work area. Do not let
them handle machines, tools, or extension cords.
4. Store idle equipment. When not in use, tools must be stored in a dry location to
inhibit rust. Always lock up tools and keep out of reach of children.
5. Use the right tool for the job. Do not attempt to force a small tool or attachment to
do the work of a larger industrial tool. There are certain applications for which this
tool was designed. It will do the job better and more safely at the rate for which it was
intended. Do not modify this tool and do not use this tool for a purpose for which it
was not intended .
6. Dress properly. Do not wear loose clothing or jewelry as they can be caught in
moving parts. Protective, electrically non-conductive clothes and non-skid footwear
are recommended when working. Wear restrictive hair covering to contain long hair.
7. Use eye and ear protection. Always wear ANSI approved impact safety goggles.
Wear a full face shield if you are producing metal filings or wood chips. Wear an ANSI
approved dust mask or respirator when working around metal, wood, and chemical
dusts and mists.
Overall Dimensions 12-3/4”L x 10-1/2”W x 4-5/8”H
Base Dimensions 4-9/16” x 5-3/16”
Table Dials 1-3/4” Diameter
Table Swivels 360 Degrees
Table Scales .001”
Travel 2-1/2” X/Y Travel
Brought To You By Augusta Flint

Page 3
SKU 03135
8. Do not overreach. Keep proper footing and balance at all times. Do not reach over
or across running machines.
9. Maintain tools with care. Keep tools sharp and clean for better and safer
performance. Follow instructions for lubricating and changing accessories.
10. Stay alert. Watch what you are doing, use common sense. Do not operate any tool
when you are tired.
11. Check for damaged parts. Before using any tool, any part that appears damaged
should be carefully checked to determine that it will operate properly and perform its
intended function. Check for alignment and binding of moving parts; any broken parts
or mounting fixtures; and any other condition that may affect proper operation. Any
part that is damaged should be properly repaired or replaced by a qualified
technician.
12. Guard against electric shock. Prevent body contact with grounded surfaces such as
pipes, radiators, ranges, and refrigerator enclosures.
13. Replacement parts and accessories. When servicing, use only identical
replacement parts. Use of any other parts will void the warranty. Only use accessories
intended for use with this tool. Approved accessories are available from Harbor
Freight Tools.
14. Do not operate tool if under the influence of alcohol or drugs. Read warning
labels on prescriptions to determine if your judgment or reflexes are impaired while
taking drugs. If there is any doubt, do not operate the tool.
15. Maintenance. For your safety, maintenance should be performed regularly by a
qualified technician.
Warning: The warnings, cautions, and instructions discussed in this instruction manual
cannot cover all possible conditions and situations that may occur. It must be under-
stood by the operator that common sense and caution are factors which cannot be
built into this product, but must be supplied by the operator.
Unpacking
When unpacking, check to make sure the parts listed on page 5 are included. If any parts
are missing or broken, please call Harbor Freight Tools at the number on the cover of this
manual as soon as possible.
Brought To You By Augusta Flint

Page 4
SKU 03135
Operation
Maintenance
Note: Prior to using the Sliding Table, read the manufacturer’s manual for the milling
machines, drills, or grinders to be used with the Sliding Table. Follow all of the instructions
and safety precautions in the manufacturer’s manual.
Warning! Before use, check the Sliding Table for cracks, bends, or breaks. Check for an
improperly mounted workpiece or any other condition thay may affect safe operation. Do not
use damaged equipment.
1. Mount the Sliding Table using two bolts (not included) to a surface able to safely hold the
Sliding Table (16.6 Lbs.) and the weight of the workpiece.
2. Secure the workpiece in the T-slots according to directions specified in the milling, drilling,
or grinding manual (not included). The T-slots are .625” at the bottom of the “T”, and .375” at the
slot opening.
3. Rotate the Wheels (#10) to adjust the table to the specific size you need.
4. Lock the table into place with the two hex head cap screws on each side.
1. Periodically apply a light coat of machine oil to all of the moving parts.
2. To clean, thoroughly wipe with a mild solvent to remove excess oil and metal shavings.
Dry with a clean cloth and then re-apply machine oil.
Brought To You By Augusta Flint

Page 5
SKU 03135
NOTE: Some parts are listed and shown for illustration purposes only and are not available
individually as replacement parts.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS
MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBU-
TOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE
OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS
QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER
AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS
SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE
BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER
REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING
OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
Parts List
Part No. Description
1 Base Slide
2 Nastar
3 Box
4 Guide Pin
5 Slide
6 Spindle (2)
7 Table
8 Bronze Nut (2)
9 Bracket (2)
10 Wheel (2)
11 Key (2)
12 Bolt (2)
13 Washer (2)
14 Nastar
15 Nut&Bolt (2)
16 Nut&Bolt (6)
17 Bolt (4)
Note: Parts 14, 15, 16, and 17 are internal and not shown on the assembly drawing.
Brought To You By Augusta Flint

Page 6
SKU 03135
Assembly Drawing
Note: Parts 14, 15, 16, and 17 are internal and not shown on the assembly drawing.
Brought To You By Augusta Flint