Central Machinery 42289 Quick reference guide

34” RADIAL BENCH
DRILL PRESS
42289
ASSEMBLY & OPERATING INSTRUCTIONS
2000
(Stand Not Shown)
Brought to You by Augusta Flint

THANKYOU for choosing a HARBOR FREIGHTTOOLS product. For future reference, please complete the
owner’s record below:
Model_____________ Serial No.____________ Purchase Date_____________
SAVE THE RECEIPT,WARRANTY ANDTHESE INSTRUCTIONS. It is important that you read the entire
manual to become familiar with the unit BEFORE you begin assembly.
Technical Specifications
Tool Name:34" Radial Bench Drill Press
Item Number: 42289
Motor: 120V/60HZ, 3 Amps, Single Speed, 1720 RPM
RadialTravel: 12"
Spindle RPM: 620, 1100, 1720, 2340, 3100
SpindleTaper: JT3
Spindle Stroke: 3"
Max. Spindle to Base: 17"
Max.SpindleTo Table: 12-3/16"
ColumnDiameter andLength: 2.335"Diameter X19-1/8" Length
ChuckTaper: JT3
Chuck Size: 5/8" with Auto Eject Chuck Key
Weight: 112 Lbs.
Overall dimensions: 64-7/8" H x 33" L
Mounting Holes: 7/8"
QuillDiameter: 1.575"
Warning: The warnings, cautions and instructions discussed in this instruction manual
cannot cover all possible conditions and situations that may occur. It must
be understood by the operator that COMMON SENSE AND CAUTION ARE
FACTORS WHICH CANNOT BE BUILT INTOTHIS PRODUCT, BUT
MUST BE SUPPLIED BYTHE OPERATOR.
The Operator
PLEASE REMEMBER:
Do not operate the product if under the influence of alcohol or drugs. Read warning labels on prescriptions to
determine if your judgment/reflexes might be impaired.
Do not wear loose clothing or jewelry as they can be caught in moving parts.
Protective gloves and non-skid footwear is recommended.
Wear restrictive hair covering to contain long hair.
Use eye and ear protection. Always wear ANSI approved impact safety goggles and
dust mask or respirator when working around metal, wood and chemical dusts and mists.
Wear a full face shield if your are producing metal or wood filings.
Do not reach over or across running machines.
#42289 REV 11/04 Page 2
Brought to You by Augusta Flint

TheOperator (Cont’d)
Maintain proper footing and balance at all times.
Do not abuse the power cord. Do not yank on cord to disconnect it from outlet. Keep the cord away from heat,
oil and sharp edges.
Work Area
TO AVOID RISK OF PERSONAL INJURY, EQUIPMENT DAMAGE, FIRE AND SHOCK, MAKE SUREYOUR
WORK AREA IS:
Free of damp, wet or rainy conditions.
Free of children (never let them handle tools or machinery).
Well-lit.
Clean and uncluttered.
Before Operating
Before using any tool, any part that appears damaged should be carefully checked to determine that it will
operate properly and perform its intended function.
Before operating your Drill Press check for damaged parts.
Make certain that the power is OFF before plugging the tool in.
Make sure all clamps, locks and bolts are tight.
Always check that adjusting keys and wrenches are removed from the machine work surface
before plugging it in.
Usegrounded receptacle onlyfor120Volthook-up.
Give the Drill Press a test run. If it makes an unfamiliar noise or vibrates irregularly, turn it off, unplug it and
have the problem corrected by a qualified technician.
Make certain to turn off and unplug the Drill Press when doing any maintenance. The tool should always be
turnedoffand unpluggedwhennot inuse.
Keep Guards in place and in working order.
Note: Performance of this tool may vary depending on variations in local line voltage. Extension Cord usage
may also affect tool performance.
Grounding/VoltageWarning
Common household current is 110-120 volts. As long as the outlet used with the tool is rated from 110-120V
there will be no complications using it with household receptacles. Plug the tool into a 110-120V properly
grounded outlet protected by a 15-amp, dual element time delay or circuit breaker.
NEVER try to plug a 110-120V tool into a 220-240V circuit or serious complications and possible injury to the
operator may occur. The plugs have different shapes to prevent this.
This tool has a three-prong plug. The third (round) prong is the ground. Cutting off the ground will result in a
safety hazard and void the warranty.
#42289 Page 3
Brought to You by Augusta Flint

If the outlet you are planning to use is the two-prong type, do not remove or alter the grounding prong in any
manner.Use an adapter and always connect the grounding plug to a known grounding source. It is
recommended that you have a qualified electrician replace the two-prong outlet with a properly grounded
three- prong outlet.
Extension Cords
Your tool has a three-prong plug, therefore you must use a three-prong extension cord. Only use rounded
jacket extension cords listed by the Underwriters Laboratories (UL). Improper use of extension cords may
cause inefficient operation of your tool which can result in overheating. Be sure your extension cord is rated to
allow sufficient current flow to the motor.
If you are using the tool outdoors, use an extension cord rated for outdoor use (signified by “WA”on the jacket).
The extension cord must have a minimum wire size depending on the amperage of the tool and the length of the
extension cord. This size is determined by its AWG (American Wire Gauge) rating. The smaller the gauge, the
greater the cable’s capacity. The amount of cords used does not matter: Total length determines the minimum
AWG rating. Every cord must meet the AWG rating. Use the chart below to determine what AWG rating is
requiredforyour situation. Cordlengthis ratedin feet. Harbor FreightTools can supply UL listed and outdoor
rated cords in multiple AWG ratings if needed.
AWG RATING CHART
CORD LENGTH 25’ 50’ 75’ 100’ 125’ 150’ 175’ 200’
AMPS AWG AWG AWG AWG AWG AWG AWG AWG
0-10.0 18 18 16 16 14 14 12 12
10.1-13.0 16 16 14 14 14 12 12 12
13.1-15 14 14 12 12 12 12 12 —-
15-18 14 12 12 12 12 12 —- —-
DONOT MODIFY YOUR PLUG IN ANY WAY. IFYOU HAVE ANY DOUBT, CALL AQUALIFIED ELECTRICIAN.
Assembly
Your Drill Press and Stand will require assembly. When assembling and operating your Drill Press, it will be
helpful to refer to each of the operational Figures as well as to the Parts List and Assembly Diagram on pages
12 through 16. Lay out all parts onto a clear section of floor or workbench prior to assembly.
Mounting Surface: Ideally, the base should be bolted down prior to the assembly of other components. The
mounting surface must be flat, level and capable of supporting the weight of the Drill combined with the
materials to be drilled. Mount the 34" Radial Bench Drill Press to the enclosed Stand.
Caution! Consider the weight of the components and take the necessary precautions when lifting. Assistance
will be required during assembly.
Stand
Step 1) Attach one Leg (part #24C) to each side of a Side Bar (part #26C). Insert one Bolt
(part #23C) through each Leg (#24C) and through the Side Bar. Tighten the
Side Bar into place at each end with a Nut (part #22C). Repeat for the other two
Legs (#24C).
Step 2) Attach one Side Panel (part #21C) to the top of the Legs (#24C) assembled in step 1.
Make certain that the holes line up with the holes in the Legs. Insert two (2) Bolts (part #23C)
through each Leg (#24C) and through the Side Panel (#21C) on both sides. Repeat for the
second set of Legs.
#42289 Page 4
Brought to You by Augusta Flint

Step 3) Connect each set of Legs (#24C) by attaching a Front Bar (part #25C) across the
middle of the unsupported Legs. Insert one Bolt (#23C) at each end and tighten
it into place with Nut (#22C). Repeat for the opposite set of Legs.
Step 4) Attach the Front Panel (part #27C) to the top of the Legs currently without a top
panel. Line up the holes in the Front Panel (#27C) with the holes in each Leg (#24C).
InsertBolt (#23C) throughtheholes andtightenon theFrontPanel withNut(#22C).
Repeat for the last set of Legs.
Base-Column-Table
Step 1) Remove any protective sleeves from the Base (part #6C) and the Column (part #1C).
With the Base (part #6C) on a flat level surface, place the Column Support (part #4C)
on the Base making certain that the holes are aligned.
Step 2) Locate the four (4) 8mm x 20mm Hex Bolts (part #5C). Insert one (1) Bolt through
eachholein the ColumnSupport (#4C) andthroughthe Base (#6C). Firmly
tighten all four (4) Bolts.
Step 3) Loosen the Screw (part #11C) in the Column Collar (part #19C) using the 3 mm Hex
wrenchsupplied. Remove theColumnCollar (#19C) and Rack(part #2C)fromthe column.
Step4) LocatetheWorm Elevationgear(part #18C). InserttheWorm-Elevationgear (#18C)
into theTable Support (part #7C). Insert theWorm Elevation as far into the opening as is
possible.
Step 5) Locate the Crank (part #8C). The Crank (part #8C) is to be installed on theWorm Elevation
(part #18C). You may need to loosen the Screw (#11C). Get the Crank as close as possible
to theTable Support (#7C) , and then tighten the Screw (#11C).
Step 6) As necessary, locate the Rack (part #2C) and with the smooth end of the Rack (#2C) pointing
upward-seeFigure 1. Slide itdown throughtheopening intheTableSupport(part #7C).
Engage the Rack into the Gear Mechanism found on the inside opening of theTable Support.
Step 7) While holding the Rack (#2C) and theTable Support (#7C) together (as assembled in the
previous steps), slide the entire assembly down over the Column (#1C). Slide the
Rack down the Column until the Rack is touching the Column Support (part #4C)
at the Base.
Step 8) Replace the Column Collar (part #19C), with the bevel side down, which was
removed in Step 3. Tighten it with the Hex wrench used in Step 3 .
Note: Only tighten the Screw (#11C) enough to keep the Collar in place. Over tightening the Screw
mayresultin breakingofthe Column Collar(#19C).
Rack (part #2C)
Crank (#8C)
Figure 1 - Rack
Column Collar (#19C)
#42289 Page 5
Brought to You by Augusta Flint

Step 9) Check the Column Collar for proper adjustment. The Column Collar should sit
evenlyonthe Column(#1C).
Step 10) Locate theTable Clamp (part #13C) and insert it into theTable Support (#7C). Once inserted,
tighten it by hand. Once this is done, rotate theWorm Elevation (#18C) clockwise with the
Crank (part #8C). If necessary, loosen the Screw (#11C) in the Crank and reposition the
Crank as close to theTable Support as possible. Tighten the Screw (#11C).
Head to Column
Step1) Insert the Locking Shoe (part #15B) into place inside the bottom of the Guide Column
(#18B)-see Figure2.
Step 2) Insert the second Locking Shoe (Part #15B) into the Guide Column (part #18B)
on the inside of the hole designated for the upper Clamping Lever (part #30B).
Step 3) With assistance, slide the Guide Column (part #18B) onto the Column (#1C) as
shown in Figure 2. It may be necessary to loosen the Guide Pin (part #16B) as well as the
Clamping Levers (part #30B) slightly to ensure that they do not protrude internally, as this will
prevent the Guide Column from sliding fully into position. Align the Guide Column (#18B) with
the Base (#6C) and firmly secure it into position with the Clamping Levers (#30B).
Step2) If it is not in place, screw the Depth-Lock Screw (part #38B) into the Depth Ring
Stop (part #37B) - see Figure 3.
Step 3) Screw the Hub (part #36B) into the Ring-Depth Stop (#37B). Screw all three (3)
Feed Rods (part #35B) firmly into the Hub (#36B). Screw each of the three Feed
Knobs (part #34B) onto the Feed Rods (#35B) - see Figure 3.
Table Support (7C)
Guide Column (18B)
Clamping Lever (30B)
Locking Shoe (15B)
Figure 2 - Head to Column
Depth Lock Screw (38B)
Hub (36B)
Feed Rod (35B) DepthRingStop(37B)
Feed Knob (34B)
Figure 3 - Feed Rod Assembly
#42289 Page 6
Brought to You by Augusta Flint

Installing the Chuck
Step 1) Remove any grease and debris from the Spindle (part #15A) ) and the tapered
bore of the Chuck (part #12A).
Step 2) Using hand pressure, press the Chuck (part #12A) up onto the Arbor (part #13A) with a
twisting motion. Tap the Chuck (#12A) gently upward using a soft faced mallet. If desired,
fine tune the alignment of the Chuck using a dial indicator. To do this, mount a dial indicator
firmly onto the Table ( #20C). Place the dial indicator pointer in contact with the Chuck, and
adjust the dial to zero. Slowly rotate the Chuck and center the pointer on the indicator. To
center the Chuck, carefully tap the Chuck with a mallet, upward and to the side as needed.
Continue this process until you are satisfied with the adjustment.
Operation
Never force the tool or attachment to do the work of a larger industrial tool. It is designed to do the job better
and more safely at the rate for which it was intended.
Settings and Adjustments
Before adjustments are made, ensure that the machine is SWITCHED OFF AND UNPLUGGED. Also make
sure all locking handles and securing screws are fully tightened when adjustments are complete.
To Adjust the Head
Step 1) To adjust the Angle, loosen the right Clamping
Lever (#30B). Then pull out the Guide Pin (part #16B) and
turn it 90 degrees so that it’s cross pin rests on top of the
outlet - see Figure 5.
Hub
Crank
Table
Base
Chuck
Ring Depth Stop
On-Off Switch
Moving Bar
Clamping
Lever
Clamping
Lever
Table
Clamp
Figure 4 - OperatingYour Drill
Guide Pin
Figure 5 - Guide Pin
#42289 Page 7
(Stand Not Shown)
Brought to You by Augusta Flint

Step 2) Align the mark on the Guide Column (#18B) with the Scale (part #33B).
Step 3) Once the Head is tilted to the desired angle, re-tighten the Clamping Lever.
Step 4) To move the Head (part #14B) back to its original position, loosen the Clamping Lever (#30B)
and pull up the Guide Pin (#16B). Turn the Guide Pin until the cross pin slides back into the
slot. Tighten the Clamping Lever (#30B).
Moving the Head Horizontally
Step 1) Loosen the left Clamping Lever (#30B) and rotate the Head 360 degrees
to the desired position.
Step2) Fasten theClampingLever(#30B)
Moving the Head Forward and Backward
Step 1) Loosen the right Clamping Lever (#30B). Turn the Moving Bar (part #32B), rotating it back and
forth if necessary - see Figure 6. Place the head in the desired position and re-tighten the
ClampingLever (#30B).
To ensure that the drill is entirely perpendicular to the table, insert a piece of straight round bar in the chuck,
place a Square on theTable and bring it up to the round bar. Adjust the Table tilt if necessary so that theTable
is correctly aligned.
To Adjust the Table
The table is capable of being raised and lower by taking the following steps.
Step1) Turningthe Crank(part #8C) clockwise willelevatetheTable(#20C); turning theCrank
counterclockwise will lower theTable. The Table Clamp (#13C) must be released before
using the Crank.
Step 2) You can tilt theTable by loosening the Hex Bolt (part #12C), tilting the table to the
desiredposition(up to45degrees) andre-tighteningthe HexBolt.
Setting the Drilling Depth
Located on the side of the Hub (#36B) is the Depth Stop Ring (part #37B) and the Depth Lock Screw
(part #38B) This allows the depth of the hole to be set so that you may drill a series of holes each to the
same depth - see Figure 7.
Step1) With the Depth Lock Screw loose, set the Scale on the Depth StopTop Ring (part #37B) to the
depth of the hole desired.
Step 2) Tighten the Depth Lock Screw (#38B) until secure.
The Drill is now set to drill holes to the desired depth.
Moving Bar (32B)
Figure 6 - Moving Head
#42289 Page 8
Brought to You by Augusta Flint

Changing the Pulley Speeds
The Drill Press has five (5) different pulley speeds at the following RPMs: 620, 1100, 1720, 2340 and 3100. A
full chart of belt arrangements for each drill speed is located on the inside of the Pulley Cover.
To change the speed of the Drill, you will need to move the belt to the appropriate pulleys. Hold the Knob (part
#17A) and lift up on the Belt Guard (part #25A). Adjust the belt tension by manually moving the belt into the
appropriate grooves on the pulleys which correspond to the speed desired. Consult the chart inside the pulley
cover and position the belts on the pulleys according to the desired drill speed - see Figure 8.
Step 1) Turn theThumb-Nut (part #28C) to loosen it and bring the Motor Pulley (#23) closer to the Spindle
Pulley (part #3A). This will allow the belt to be moved easily.
Cutting Speeds
The factors which determine the best speed to use in the drill press operation are:
1) Type of material to be drilled
2) Size of hole
3) Type of drill bit
4) Quality of the hole or cut desired.
Generally, the SMALLER THE DRILL BIT the GREATERTHE REQUIRED RPM. In soft material, the speed
should be higher than for hard metals. As a general guide, the drill speed for a given drill bit size is listed in the
chart on the next page.
Figure 7 - Setting Drilling Depth
Depth Lock Screw
Motor Pulley
Spindle Pulley
Figure 8 - Changing the Pulley Speed
#42289 Page 9
Brought to You by Augusta Flint

SpeedRange (RPM) 3100 2340 1720 1100 620
Wood in. 3/8 5/8 7/8 1-1/4" 1-1/4"
mm 9.5 18 22 31.75 31.75
Zinc Diecast in. 1/4 3/8 1/2 3/4 3/4
mm 6.4 9.5 12.5 19 19
Alum. & Brass in. 7/32 11/32 15/32 11/16 11/16
mm 5.6 8.75 12 17.5 17.5
Plastic in. 3/16 5/16 7/16 5/8 5/8
mm 4.8 7.9 11 16 16
Cast Iron/Bronze in. 1/8 1/4 11/32 1/2 1/2
mm 3.2 6.4 8.75 12.5 12.5
Mild Steel/Malleable in. 3/32 5/32 1/4 3/8 3/8
mm 2.4 4 6.4 9.5 9.5
Cast Steel & Med Carbon in. 1/16 1/8 3/16 5/16 5/16
mm 1.6 3.2 4.8 7.9 7.9
Stainless &Tool Steel in. 3/64 1/16 1/8 1/4 1/4
mm 1.2 1.6 3.2 6.4 6.4
Running the Drill Press
Step 1) Insert the drill into the jaws of the Chuck approximately 1", ensuring that the jaws do not
touch the flutes of the drill. Before tightening the Chuck, ensure that the drill is centered
within the jaws.
Step 2) Make certain that theTable height and position is set so that the drill travel range is sufficient
for the material to be drilled.
Step 3) Make certain that the work piece is securely clamped. It should be held in a drill vise or
bolted to theTable. Never hold the material with your bare hands while drilling as this may
result in severe personal injury.
Step4) If the material is irregularly shaped and can not be laid flat on the table, it should be securely
blocked and clamped. Any tilting, twisting or shifting will result not only in a roughly drilled
hole but also increases the chances of damage to the drill.
Step 5) FOR FLATWORK, lay the workpiece onto a wooden base and clamp it down firmly
against the table to prevent it from turning.
Step 6) FOR SMALL MATERIALS that cannot be clamped to the table, use a drill press
vise. Made sure that the vise is clamped or bolted to the table.
Step 7) WHEN DRILLING COMPLETELY THROUGH WOOD, always position a piece of
scrap wood between the material and the table to prevent splintering on the
underside of the material as the drill breaks through. The scrap piece of wood
must make contact with the left side of the column. Also, set the depth of the drill so that the
drill will not come in contact with the table - or align the table so that the hole in its center is in
line with the drill bit.
Step 8) Once the instructions above have been followed, make certain guards are in
place and turn the machine ON. The ON-OFF Lock Switch (part #1B) is turned ON and
OFF as follows: The switch has a“snap-in”piece which is to be removed to lock the power
switch. Make certain that this piece, when removed, is stored in a safe place. Insert the
“snap-in”piece into the switch. To turn the machine ON, put your finger under the switch lever
and push up. To turn the machine OFF, pull the lever down.
#42289 Page 10
Brought to You by Augusta Flint

After Operation-Maintenance
CLEANING: Regularly clean the work surface with a dry brush or clean cloth. Keep machined
parts of the press lightly greased. Always keep the motor and chuck clean. Prevent metal, wood, dust and
debris from accumulating in the Motor and Chuck areas.
If the jaws do not operate smoothly, have the chuck serviced by a qualified technician.
Lubrication: For average use, lubricate twice a year with a 20 to 30 weight household oil. Lubricate more
frequentlywithincreased use.
STORAGE: Remove drill bits and store them in a safe place.
Child-proof the machine and work area. Make sure to use padlocks, master switches and remove the Lock
Switch’s“snap-in”piece.
IF THERE IS ANY QUESTION ABOUT ACONDITION BEING SAFE OR UNSAFE, DO NOT OPERATE THE TOOL.
Troubleshooting
#42289 Page 11
Brought to You by Augusta Flint

Unpacking
UNPACK AND CHECK CONTENTS
When unpacking your 34" Radial Bench Drill Press check to make sure the following parts are included. If
any parts are missing or broken, please call HARBOR FREIGHTTOOLS at 1-800-444-3353.
Parts List - #42289A
Part # Description Part # Description
1A V-belt M 58 15A Spindle
2A Pulley Nut 16A Ball Bearing
3A Spindle Pulley 17A Knob
4A Insert Pulley 18A Screw M5 x 12
5A Ball Bearing 19A Screw M5 X 12
6A Retaining Ring 17mm 20A Cord Clamp
7A Retaining Ring 11 mm 21A Screw M6 x 12
8A Ball Bearing 22A Lock Washer
9A RubberWasher 23A Motor Pulley
10A Tube Quill 24A Screw M6 x 10
11A Chuck Key 25A Belt Guard
12A Chuck 26A FormWasher
13A Arbor 27A Spacer
14A Key Drift
Parts List - #42289-B
Part # Description Part # Description
1B Lock Switch 21B Motor Mount
2B Switch Cover 22B Motor
3B Screw Pan Head 23B Nut M8
4B Switch Box 24B Washer
5B Screw-Set Special 25B Cord - Motor
6B Hex Nut 26B Washer
7B Hex Nut M 12 27B Hex Screw M 8 x 20
8B Cap-spring 28B Thumb Nut
9B Spring-Torsion 29B Power Cord
10B Retainer-Spring 30B Clamping Lever
11B Seat-spring 31B Horizontal Rack
12B Pin-Roll 32B Moving Bar
13B Socket Set Screw 33B Scale
14B Head 34B Feed Knob
15B Locking Shoe 35B Feed Rod
16B Guide Pin 36B Hub
17B RetainingRing 37B DepthStopRing
18B Guide Column 38B Depth Lock Screw
19B HorizontalTube 39B Pin-Stop
20B Mount-Cover
#42289 Page 12
Brought to You by Augusta Flint

Parts List - #42289-C
Part # Description Part # Description
1C Column 19C Column Collar
2C Rack 20C Table
4C Column Support 21C Side Panel
5C Hex Bolt M8 x 20 22C Nut M6
6C Base 23C Bolt M6 x 16
7C Table Support 24C Leg
8C Crank 25C Front Bar
10C Pin Gear 26C Side Bar
11C Screw M 6 x 20 27C Front Panel
12C Hex Bolt M 12 x 22 28C NutM8
13C TableClamp 29C Washer 8 mm
17C Gear-Helical 30C Bolt M 8 x 40
18C Worm-Elevation
#42289 Page 13
PLEASEREADTHE FOLLOWINGCAREFULLY
THEMANUFACTURER AND/ORDISTRIBUTOR HAS PROVIDEDTHEPARTSDIAGRAMINTHIS
MANUALASA REFERENCETOOLONLY. NEITHERTHEMANUFACTURERNORDISTRIBUTOR
MAKES ANY REPRESENTATION OR WARRANTY OF ANY KINDTOTHE BUYERTHAT HE OR SHE
IS QUALIFIEDTO MAKE ANY REPAIRSTOTHE PRODUCT ORTHAT HE OR SHE IS QUALIFIEDTO
REPLACEANY PARTSOFTHEPRODUCT. IN FACT,THEMANUFACTURERAND/ORDISTRIBUTOR
EXPRESSLY STATESTHAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE
UNDERTAKEN BY CERTIFIEDAND LICENSEDTECHNICIANSANDNOTBYTHEBUYER.THE
BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TOTHE
ORIGINALPRODUCTOR REPLACEMENT PARTSTHERETO, OR ARISINGOUTOF HIS ORHER
INSTALLATION OFREPLACEMENTPARTSTHERETO.
Brought to You by Augusta Flint

All parts in this diagram correspond to parts listed with an“A”suffix.
Assembly Diagram - #42289-A
#42289 Page 14
Brought to You by Augusta Flint

Assembly Diagram - #42289-B
All parts in this diagram correspond to parts listed with a “B”suffix.
#42289 Page 15
Brought to You by Augusta Flint

Assembly Diagram - #42289-C
All parts in this diagram correspond to parts listed with an “C”suffix.
Wiring Diagram
#42289 Page 16
Brought to You by Augusta Flint