Chamberlain LA350 User manual

PLEASE READ THE MANUAL CAREFULLY BEFORE INSTALLATION AND OPERATION
THIS PRODUCT TO BE INSTALLED BY A TRAINED
GATE SYSTEMS TECHNICIAN ONLY.
LA350
SWING GATE OPERATOR
INSTALLATION MANUAL

2
TABLE OF CONTENTS
SAFETY................................................................................................................................................ 3-5
INTRODUCTION
Specifications...........................................................................................................................................6
Carton Inventory......................................................................................................................................6
Tools Needed...........................................................................................................................................7
Overview of Gate Operator and Wiring for Control Box...........................................................................7
INSTALLATION
Determine the Position of the Post Bracket.............................................................................................8
Dimensions of Gate Operator...................................................................................................................9
Determine the Position of the Gate Bracket..................................................................................... 10-11
Adjust Travel Distance ...........................................................................................................................11
Clutch Release .......................................................................................................................................12
Install the Control Box ...........................................................................................................................12
WIRING
Connect the Gate Operator to the Control Box.......................................................................................13
Connect the Second Gate Operator to the Control Box..........................................................................13
Voltage Selection ...................................................................................................................................14
Power Wiring.........................................................................................................................................14
Connect a Battery Backup to the Control Box (Optional).......................................................................16
Wiring Diagram......................................................................................................................................17
TRAVEL LIMIT SETTINGS......................................................................................................................18
PROGRAMMING
Program Remote Control.......................................................................................................................18
Erase All Codes......................................................................................................................................18
LiftMaster®Internet Gateway.................................................................................................................19
Erase a LiftMaster®Internet Gateway ....................................................................................................19
SETTINGS
Opening/Closing Delay Time Settings....................................................................................................20
Single Gate Leaf Operation Setting ........................................................................................................20
Operation Mode Setting.........................................................................................................................20
Auto Closing Setting..............................................................................................................................20
Force Adjustment...................................................................................................................................21
Soft Start and Stop Speed Setting.........................................................................................................21
Moving Speed Setting............................................................................................................................21
Operating Time Setting..........................................................................................................................21
Maglock (Optional) ................................................................................................................................22
Flashing Light (Optional) .......................................................................................................................22
The Photoelectric Sensor (Optional) Connection...................................................................................22
OPERATION AND MAINTENANCE.................................................................................................... 23-25
TROUBLESHOOTING .............................................................................................................................26
SERVICE KITS........................................................................................................................................27
ACCESSORIES .......................................................................................................................................27

3
MECHANICAL
ELECTRICAL
When you see these Safety Symbols and Signal Words on
the following pages, they will alert you to the possibility of
serious injury or death if you do not comply with the warnings
that accompany them. The hazard may come from something
mechanical or from electric shock. Read the warnings carefully.
When you see this Signal Word on the following pages, it will
alert you to the possibility of damage to your gate and/or the gate
operator if you do not comply with the cautionary statements that
accompany it. Read them carefully.
Safety Precautions For Swing and Ornamental Grill Type Gates
SAFETY
To prevent SERIOUS INJURY or DEATH from a moving gate:
• Entrapment protection devices MUST be installed to protect anyone who may come
near a moving gate.
• Locate entrapment protection devices to protect in BOTH the open and close gate
cycles.
• Locate entrapment protection devices to protect between moving gate and RIGID
objects, such as posts.
• A swinging gate shall NOT open into public access ways.
• SAVE THESE INSTRUCTIONS.
We recommend to use E-locks/Maglock against
vandalism and if gate is installed where strong winds
may appear.
IMPORTANT NOTE
• BEFORE attempting to install, operate or maintain the operator, you must read and fully understand
this manual and follow all safety instructions.
• These instructions are intended to highlight certain safety related issues. These instructions are
not intended to be comprehensive. Because each application is unique, it is the responsibility of
the purchaser, designer, installer and end user to ensure that the total gate system is safe for its
intended use.
• Save These Instructions.

4
To reduce the risk of SEVERE INJURY or DEATH from an incorrect installation:
1. Vehicular gate systems provide convenience and security. Gate systems are comprised
of many component parts. The gate operator is only one component. Each gate
system is specifically designed for an individual application.
2. Gate operating system designers, installers and users must take into account the
possible hazards associated with each individual application. Improperly designed,
installed or maintained systems can create risks for the user as well as the bystander.
Gate systems design and installation must reduce public exposure to potential
hazards.
3. A gate operator can create high levels of force in its function as a component part of a
gate system. Therefore, safety features must be incorporated into every design.
Specific safety features include:
• Gate Edges • Guards for exposed rollers • Photoelectric Sensors
• Screen Mesh • Vertical Posts • Instructional and Precautionary Signage
4. Install the gate operator only when:
a. The operator is appropriate for the construction and the usage of the gate.
b. All openings of a horizontal swing gate are guarded or screened from the bottom of
the gate to a minimum of 4’ (1.2 m) above the ground to prevent a 2 1/4" (6 cm)
diameter sphere from passing through the openings anywhere in the gate, and in
that portion of the adjacent fence that the gate covers in the open position.
c. All exposed pinch points are eliminated or guarded, and guarding is supplied for
exposed rollers.
5. The operator is intended for installation on gates used for vehicles. Pedestrians should
be supplied with a separate access opening.
6. The gate must be installed in a location so that enough clearance is supplied between
the gate and adjacent structures when opening and closing to reduce the risk of
entrapment. Swinging gates shall not open into public access areas.
7. The gate must be properly installed and work freely in both directions prior to the
installation of the gate operator.
8. Controls must be far enough from the gate so that the user is prevented from coming
in contact with the gate while operating the controls.
SAFETY
IMPORTANT SAFETY INFORMATION

5
SAFETY
9. For a gate operator utilizing a non-contact sensor:
a. Reference owner’s manual regarding placement of non-contact sensor for each
type of application.
b. Care shall be exercised to reduce the risk of nuisance tripping, such as when a
vehicle trips the sensor while the gate is still moving.
c. One or more non-contact sensors shall be located where the risk of entrapment or
obstruction exists, such as the perimeter reachable by a moving gate or barrier.
10. For a gate operator utilizing a contact sensor such as an edge sensor:
a. A hard wired contact sensor shall be located and its wiring arranged so the
communication between the sensor and the gate operator is not subject to
mechanical damage.
b. A wireless contact sensor such as the one that transmits radio frequency (RF)
signals to the gate operator for entrapment protection functions shall be located
where the transmission of the signals are not obstructed. A wireless contact sensor
shall function under the intended end-use conditions.
c. One or more contact sensors shall be located on the inside and outside leading
edge of a swing gate. Additionally, if the bottom edge of a swing gate is greater
than 6" (15 cm) above the ground at any point in its arc of travel, one or more
contact sensors shall be located on the bottom edge.
IMPORTANT SAFETY INFORMATION
IMPORTANT: The MyQ feature and its accessories are not permitted for use in the countries
of Peru and Chile.

6
Specifications
INTRODUCTION
Carton Inventory
Main AC Supply: 110-127Vac / 220-240Vac; 50/60Hz
Motor Voltage: 24 Vdc
Input Power: 100 W
Ambient Temperature Range: -25 ~ +50 ˚C
Maximum Weight for single Gate Leaf: 350 Kg
Maximum Width for single Gate Leaf: 1.8 m, 2.5 m (with electric lock)
Maximum Open Angle: 120˚
Protection Level: IP 44
Maximum Travel Distance: 350 mm
Daily Cycle Rate: Maximum 50 cycles per day
Weight per Gate Operator: 6 Kg
Installation
Manual
(Not shown)
Remote Control (2)Post Mounting
Bracket (2) Gate Mounting Bracket (2)
Washer and Bolt
(attached to the arm)
Control Box
Release Key (3) Hairpin Clip (2)Clevis Pin (2) M8x60 Screws (8)
Operator
Model LA350 (2)

7
Overview of Gate Operator and Wiring for Control Box
Tools Needed
LA350
Gate Operator
with 1000 mm
cable
Cable for
Photoelectric Sensor:
4 X O.5 mm2 or
2 X O.5 mm2 (optional)
Extension Cables
for MOTO2:
2 X 1.0 mm2
(not supplied)
Cable for Flashing
Light: 2 X 1.O mm2
(optional)
Remote
Control
FA42LM
Flashing Light
(optional)
FA70LM
Control Box
LA350
Gate Operator
with 1000 mm
cable
Power Cable:
2 X 1.5 mm2
Cables for
MOTO1
& MOTO2:
2 X 1.0 mm2
FA31LM Photoelectric
Sensor (optional)
Cable for
Photoelectric
Sensor:
4 X O.5 mm2
or 2 X O.5 mm2
(optional)
Junction Box
(not supplied)
FA31LM Photoelectric
Sensor (optional)
Cables used must meet all National and Local Codes for outdoor use.
INTRODUCTION

8
Determine the Position of the Post Bracket
1. Measure the Value C.
2. Value D will depend on the position where the post bracket is mounted.
3. Value A is the total length for both C and D.
4. Value B will depend on Value A and the maximum opening angle of the gate. Refer to
Table 1 below.
NOTE: For optimal mechanical advantage Value B must be close or equal to Value A.
5. Determine the A and B measurements provided in Table 1 to confirm the position where the post
bracket will be mounted.
A
B
D
C
Gate
Gate Operator
Post Bracket
Gate Bracket
Gate Post
100 110 120 130 140 150 160 170 180 190 200
100
110
120
130
140
150
160
170
180
190
200
Max 120˚
Max 110˚
Max 100˚
Max 90˚
A
B
Unit = mm
Table 1 Maximum Gate Opening
INSTALLATION

9
6. Using the post bracket as a reference, mark and drill the holes for the post bracket.
7. Attach the post bracket with the M8x60 screws, washers, and nuts.
8. The slots on the post bracket allow for alignment. When the post bracket is level tighten the nuts.
Level
Drill hole M8x60 screw
Washers
Nut
55 mm
115.3 mm
93.5 mm
95 mm
835 mm
350 mm
Dimensions of Gate Operator
INSTALLATION

10
730 mm
38 mm
Determine the Position of the Gate Bracket
1. Position the gate bracket 730 mm from the post bracket and 38 mm lower than the post bracket.
2. Temporarily secure the gate bracket to the gate with a clamp.
3. Align the hole on the operator fork to the post bracket hole. Attach the operator to the post bracket
using the clevis pin and secure with a hairpin clip.
Level ruler
When installing the gate
bracket, the washer
should face downward.
INSTALLATION

11
4. Secure the operator to the gate bracket using the screw and washer (provided) and tighten.
4. Permanently secure the gate operator to the gate using hardware (not provided) or by welding.
5. Engage the operator with the release key, see page 12.
5. Manually release the operator clutch with the release key, see page 12.
6. Manually open and close the gate. Ensure that the operator does not bind.
Adjust Travel Distance
1. To adjust the gate’s traveling distance, loosen each the adjustment screws using an Allen wrench.
2. Stop the gate in the “full closed” position. Adjust and tighten the close adjustment screw.
3. Stop the gate in the “full open” position. Adjust and tighten the open adjustment screw.
Adjustment Screws
Closing Stop
Opening Stop
Washer
Bolt
INSTALLATION

12
To release the clutch: Insert the release key and turn it 180 degrees clockwise. To engage the clutch:
Insert the release key and turn it 180 degrees counterclockwise.
Clutch Release
Release
Engage
Release
Engage
The clutch release for the left operator The clutch release for the right operator
INSTALLATION
1. Install the control box 1.7 m above the ground, see page 7. Use screws and anchors (provided)
to secure the control box.
24V Transformer
24V Control board
Power panel
Install the Control Box
226.5 mm
280 mm
108 mm
296 mm

13
To reduce the risk of SEVERE INJURY or DEATH:
• ANY maintenance to the operator or in the area near the operator MUST NOT be
performed until disconnecting the electrical power (AC or solar and battery). Upon
completion of maintenance the area MUST be cleared and secured, at that time the unit
may be returned to service.
• Disconnect power at the fuse box BEFORE proceeding.
NOTE: The operator should be on a separate fused line of adequate capacity.
• ALL electrical connections MUST be made by a qualified individual.
• DO NOT install any wiring or attempt to run the operator without consulting the wiring
diagram.
• ALL power wiring should be on a dedicated circuit and well protected.
• ALL power and control wiring MUST be run in separate conduit.
• BEFORE installing power wiring or control stations be sure to follow all specifications
and warnings described below. Failure to do so may result in SEVERE INJURY to
persons and/or damage to operator.
WIRING
Connect the Gate Operator to the Control Box
NOTE: The operator wired to the MOTO1 terminal will always open first and close last.
1. Select a hole in bottom of the control box to be used for the operator cable.
2. Insert a watertight connector into the bottom of the control box and tighten with nut.
3. Insert the operator cable through the watertight connector.
4. Connect the operator cable wires to the MOTO1 terminal on the board. Blue wire to + and brown
wire to -.
5. Tighten the watertight connector nut.
Connect the Second Gate Operator to the Control Box
NOTE: The operator wired to the MOTO2 terminal will always open last and close first.
Before digging, contact local underground utility locating companies.
1. Trench across driveway to bury the extension cable (not provided). Use PVC conduit to prevent
damage to cables.
2. Insert the extension cable through a watertight connector mounted in the control box.
3. Connect the extension cable wires to the MOTO2 connector on the board. Take note of which wire
is connected to + and which wire is connected to -.
4. Tighten the watertight connector nut.

14
5. Mount a watertight junction box (not provided) that is able to accommodate two watertight
connectors (not provided) within 3 feet (0.9 m) of the second operator.
6. Remove the cover from the watertight junction box and set aside.
7. Route the operator cable through a watertight connector into the junction box.
8. Route the extension cable through a watertight connector into the junction box.
9. Connect the wires from the operator and the extension cable inside the junction box. Connect the
blue wire from the operator to the extension cable wire connected to the + terminal on the board.
Connect the brown wire from the operator to the extension cable wire connected to the - terminal on
the board.
10. Tighten the watertight connector nuts.
11. Reinstall the cover on the watertight junction box.
Voltage Selection
The operator can be wired for either 110-127 Vac or 220-240 Vac through a jumper setting.
NOTE: The factory default setting is 220 Vac.
For 110-127 Vac installations:
1. Turn off the AC power from the main power source circuit breaker.
2. Place the jumper on J3 and the cover on J2 on the control board.
For 220-240 Vac installations:
1. Turn off the AC power from the main power source circuit breaker.
2. Place the jumper on J2 and the cover on J3 on the control board.
Power Wiring
The operator can be wired for either 110-127 Vac or 220-240 Vac.
1. Turn off the AC power from the main power source circuit breaker.
2. Select a hole in bottom of the control box to be used for the incoming AC power.
3. Insert a watertight connector into the bottom of the control box and tighten with nut.
4. Insert the AC power wires through the watertight connector.
5. Connect the “hot” wire to the L terminal on the board.
6. Connect the neutral wire to the N terminal on the board.
7. Tighten the watertight connector nut.
8. Restore power to the control box.
WIRING
To reduce the risk of SEVERE INJURY or DEATH:
• DO NOT TOUCH the unused connections on J2 or J3 as they are energized.
• Replace cover before reconnecting or connecting power.

15
WIRING
110-127 Vac
OFF
ON
ON
OFF
J3
J2
230V127VN
POWER LINE
GND
GND
S1COM S2COM
IAD:1
IAD:2
VCCAD
RP3
RP1
RP2
RP4
+
++
-- -
BATAD
+24V
+3.3V
+5V
CHAR
VCC33V
Pb
ET-LA350-R NO.06 2013.9.20
4
3
21
87654321
OFF
ON
-BATTERY+24V AC IN
Charging
+MOTO2- Gate1Gate2
GNDIR2IR1GND
IR.V+
GND
DC.L+Lock+
+MOTO1-
Transformer In
NL
SBC
LEARN
FORCE
RV LV
TIMER
SBC1SBC
IR2IR1
220-240 Vac
Indicator
J3
J2
R78
R77
R80
IC6
VT2-B
VT1-B
Q18
RP3
C30
D33
SW1
D8
R75
R72
R70
R73
R71
R68
Q15
Q17
Q14
LED2
LED3
LED1
SW3
C32
C1
C2
C5
C6
C7
C8
C9
C10
C11
C12
C13
C14
C17
C19
C20
C21
C22
C23
C24
C25
C29
C31
C33
C35
C36
C37
C38
C39
C40
C41
C42
C43
CON1CON2
CON5
CON6
CON7
D1
D2
D3
D4
D5
D6
D7 D9
D10
D11
D12
D13
D14
D15
D16
D17
D18
D19
D20
D21
D22
D23
D24
D25
D26
D27
D36
D29
D30
D31
D32
D34
D35
DB1
DZ2
DZ1
IC1
IC2
IC3
IC4
IC5
J1
K1
K2
K3
K4
L1
LED4
LED5
LED6
LED7
LED8
Q1
Q2 Q3
Q4
Q5
Q6
Q7 Q8
Q9
Q12
Q11
Q13
Q16
Q19
R1
R2
R3
R4
R5
R6
R7
R8
R9
R10
R11
R12
R13
R14
R15
R16
R17
R18
R19 R20
R21
R22
R23
R24
R25
R26
R27
R28
R29
R30
R31
R32
R33
R34
R35
R36
R37
R38
R39 R40
R41
R43
R44
R45
R46
R47
R48
R49
R50
R51
R52
R53
R54
R55
R56
R57 R58
R59
R60
R62
R61
R64
R63
R65
R66 R67
R69
R74
R76
RF1
RP1
RP2
RP4
S1 S2
U1
VT1
VT2
C18
CON4
RV1
CON3
DZ3
R100
1
1
MM
LN
POWER IN
24V DC Motor LOCK DC Lamp
IR TX IR RX1,2
Gate1,2
24V Battery
24V Transformer
Brown
Blue
Brown
Blue

16
WIRING
CONTROL BOARD Jumper with
10A/250V
in-line fuse
(not supplied)
Connect a Battery Backup to the Control Box (Optional)
The batteries are charged in the circuit by the integrated transformer.
Recommended items for a battery backup application (not provided):
• Two 12V 4Ah batteries (McNair Model RB-FM-12V-4AH)
• Battery box (Attwood Model 9069-1)
• 3 x 18 AWG (1.00 mm) VM-1 105°C 600V, 1 wire must have a 10A/250V in-line fuse
1. Disconnect/turn OFF AC power to the operator.
2. Select a hole in the bottom of the control box to be used for the battery backup cable (not
provided).
3. Insert a watertight connector (not provided) into the bottom of the control box and tighten with
nut.
4. Insert the battery cable through the watertight connector mounted in the bottom of the control box.
5. Connect the battery cable to the BATTERY terminal on the control board.
6. Tighten the watertight connector nut.
7. Install battery box in desired location (no further than 10’ away).
9. Place the batteries in the battery box.
10. Connect a jumper with an in-line fuse between the positive (+) terminal on one battery and the
negative (-) terminal on the other battery.
11. Connect the positive battery cable wire to the positive (+) terminal on the battery.
12. Connect the negative battery cable wire to the negative (-) terminal on the other battery.
13. Reconnect/turn ON AC power to the operator.

17
110-127 Vac
OFF
ON
ON
OFF
J3
J2
230V127VN
POWER LINE
GND
GND
S1COM S2COM
IAD:1
IAD:2
VCCAD
RP3
RP1
RP2
RP4
+
++
-- -
BATAD
+24V
+3.3V
+5V
CHAR
VCC33V
Pb
ET-LA350-R NO.06 2013.9.20
4
3
21
87654321
OFF
ON
-BATTERY+24V AC IN
Charging
+MOTO2-
Gate1Gate2
GNDIR2IR1GND
IR.V+
GND
DC.L+Lock+
+MOTO1-
Transformer In
NL
SBC
LEARN
FORCE
RV LV
TIMER
SBC1SBC
IR2IR1
220-240 Vac
Indicator
J3
J2
R78
R77
R80
IC6
VT2-B
VT1-B
Q18
RP3
C30
D33
SW1
D8
R75
R72
R70
R73
R71
R68
Q15
Q17
Q14
LED2
LED3
LED1
SW3
C32
C1
C2
C5
C6
C7
C8
C9
C10
C11
C12
C13
C14
C17
C19
C20
C21
C22
C23
C24
C25
C29
C31
C33
C35
C36
C37
C38
C39
C40
C41
C42
C43
CON1CON2
CON5
CON6
CON7
D1
D2
D3
D4
D5
D6
D7 D9
D10
D11
D12
D13
D14
D15
D16
D17
D18
D19
D20
D21
D22
D23
D24
D25
D26
D27
D36
D29
D30
D31
D32
D34
D35
DB1
DZ2
DZ1
IC1
IC2
IC3
IC4
IC5
J1
K1
K2
K3
K4
L1
LED4
LED5
LED6
LED7
LED8
Q1
Q2 Q3
Q4
Q5
Q6
Q7 Q8
Q9
Q12
Q11
Q13
Q16
Q19
R1
R2
R3
R4
R5
R6
R7
R8
R9
R10
R11
R12
R13
R14
R15
R16
R17
R18
R19 R20
R21
R22
R23
R24
R25
R26
R27
R28
R29
R30
R31
R32
R33
R34
R35
R36
R37
R38
R39 R40
R41
R43
R44
R45
R46
R47
R48
R49
R50
R51
R52
R53
R54
R55
R56
R57 R58
R59
R60
R62
R61
R64
R63
R65
R66 R67
R69
R74
R76
RF1
RP1
RP2
RP4
S1 S2
U1
VT1
VT2
C18
CON4
RV1
CON3
DZ3
R100
1
1
MM
LN
POWER IN
24V DC Motor LOCK DC Lamp
IR TX IR RX1,2 Gate1,2
24V Battery
24V Transformer
Brown
Blue
Brown
Blue
WIRING
Wiring Diagram
SBC is an open/close command for a single gate. NOTE: SBC is also used for the travel limit setting in conjunction with the S1 No. 8 in the ON position.

18
1. Release the clutch on both operators with the release key. Open both gates completely, then engage
the clutches.
2. Set DIP switch S1 No. 8 to ON position.
3. Press button on the control board, both
gate leaves will close completely.
4. Press button again, both gate leaves will open completely.
5. Set DIP switch S1 No. 8 to OFF position.
ON
OFF
1 2 3 4 5 6 7 8
S1
SBC
SBC
TRAVEL LIMIT SETTINGS
PROGRAMMING
NOTICE: Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for this product could void the user’s authority to operate the
equipment.
This device is designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to:
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Program Remote Control
1. Press and release the LEARN button , LED1 will light.
2. Press the desired button on the remote control to program it to the operator.
The operator will automatically exit learn mode (LED1 will flash and go out) if programming is
successful. To program additional Security✚2.0™ remote controls or remote control buttons, repeat
the programming steps above. Press the LEARN button a second time to exit programming at any time.
LEARN
Erase All Codes
1. Press and hold the LEARN button , LED1 will light.
2. Hold the LEARN button for approximately 6 seconds. LED1 will go out and all remote control codes
are now erased.
LEARN
The antenna(s) used for this must be installed to provide a separation distance of at least 20 cm from all persons and must not be collocated
The antenna(s) used for this must be installed to provide a separation distance of at least 20 cmfrom all persons and must not be collocated or operating
or operating in conjunction with any other antenna or transmitter, except in accordance with FCC multi-transmitter product procedures.

19
PROGRAMMING
LiftMaster®Internet Gateway
To program the operator to the LiftMaster®Internet Gateway:
1. Connect the Ethernet cable to the LiftMaster®Internet Gateway and the router.
2. Connect power to the LiftMaster®Internet Gateway.
3. Create an online account by visiting www.myliftmaster.com.
4. Register the LiftMaster®Internet Gateway.
5. Use an internet enabled computer or smartphone to add devices. The LiftMaster®Internet Gateway
will stay in learn mode for three minutes.
6. Press the LEARN button on the operator (LED1 will light as it enters learn mode). The LiftMaster®
Internet Gateway will pair to the operator if it is within range and LED1 will flash and go out if
programming is successful.
Erase a LiftMaster®Internet Gateway
1. Press and hold the LEARN button , LED1 will light.
2. Hold the LEARN button for approximately 6 seconds. LED1 will go out and all remote control codes
are now erased.
3. Press and hold the LEARN button a second time, LED1 will light again.
4. Hold the LEARN button for approximately 6 seconds. LED1 will go out and all gateways are now
erased.
LEARN

20
Opening/Closing Delay Time Setting
Factory default is set at 2 seconds.
The Open/Closing Delay times can be individually set
from 1-4 seconds.
Opening Delay:
1 OFF and 2 OFF = 1 second
1 ON and 2 OFF = 2 seconds
1 OFF and 2 ON = 3 seconds
1 ON and 2 ON = 4 seconds
The minimum delay time is 1 second.
Closing Delay:
3 OFF and 4 OFF = 1 second
3 ON and 4 OFF = 2 seconds
3 OFF and 4 ON = 3 seconds
3 ON and 4 ON = 4 seconds
The minimum delay time is 1 second.
Single Gate Leaf Operation Setting
5 ON = Only MOTO1 operator is available.
5 OFF = Both MOTO1 and MOTO2 operators are available.
Operation Mode Setting
6 ON = The operation mode is :
OPEN-STOP-CLOSE-OPEN
6 OFF = The operation mode is:
OPEN-STOP-CLOSE-STOP-OPEN
Auto Close Time Setting
Factory default for this function is OFF. The time can be set
from 0-105 seconds.
1 = 15s 2 = 30s 3 = 60s
If all the DIP switches are set to the ON position, the auto
closing time is 105 seconds. If all the DIP switches are set
to the OFF position, the gate leaf will not close automatically.
ON
OFF
1 2 3 4 5 6 7 8
S1
Opening Delay set for 4 seconds
SETTINGS
MOTO1 only
OPEN - STOP - CLOSE - OPEN
ON
OFF
S2
1 2 3 4
ON
OFF
1 2 3 4 5 6 7 8
S1
ON
OFF
1 2 3 4 5 6 7 8
S1
ON
OFF
1 2 3 4 5 6 7 8
S1
ON
OFF
1 2 3 4 5 6 7 8
S1
Closing Delay set for 4 seconds