Chamberlain CSW24VDC User manual

2
1
7
5
3
6
89
10
4
11
Model CSW24VDC
1MyQ®Enabled Indoor Controls
2Remote Controls
3Photoelectric Sensors
4Loop Detectors
5Lock
6Mounting Plate
7Solar
8Batteries
9Heater
10 Swivel Arm
11 dwellingLIVE
7
CPS-RPEN4GM
Photoelectric Sensor
(Monitored)
The photoelectric sensors are
designed to detect an obstacle in
the path of the electronic beam
and stop the operator. Includes
mounting brackets.
CPS-UN4
Photoelectric Sensor
(Monitored)
Low power through beam
photoelectric sensors, 45 foot
sensing distance, NEMA 4 rated.
Works in conjunction with Power
Management System to save
power.
LOOPDETLM
Plug-In Loop Detector
Plug-in Loop Detector,
(LOOPDETLM) innovative design
includes 8 sensitivity settings &
boost, ensures vehicles are easily
identified.
892LT & 894LT
2-Button and 4-Button
Security+ 2.0™ Learning
Remote Controls
These remote controls are ideal
for gated communities. One
button can control a gate operator
and the other(s) can control
a garage door. It can also be
programmed to different codes
and frequencies.
811LM & 813LM
Universal DIP Single-Button
and 3-Button Remote Control
These remote controls are ideal
for applications such as gated
communities or commercial
applications requiring a large
number of remotes for a common
entrance.
828LM*
Internet Gateway
Imagine your Customers being
at the office and receiving an
alert if they left their garage
or gate open. Or being able to
turn on their lights before they
get home. The 828LM Internet
Gateway, which connects to your
Customer’s router and enables
smartphone control, does this by
letting them monitor, open and
close their garage door or gate
from anywhere and control home
lighting.
3
5
4
9
8
6
2
1
Commercial DC
VEHICULAR SWING GATE OPERATOR
ORDER SUMMARY
Customer: Date:
Project:
Architect/Engineer:
Contractor:
Gate Length (ft.): Gate Weight (lbs.): Solar (Y/N):
Power Source (120 or 240 VAC):
LiftMaster.com
* LiftMaster®Internet Gateway Accessory functionality is
dependent on communication with a MyQ®Enabled gate
operator. MyQ®Technology communication can be limited
by distance and type of exterior building materials. A
general range estimate is 300 ft.
Gate Operator and
Accessory Site Plan
LiftMaster gate operators comply with UL 325 standards. Important: To be compliant with UL 325 and industry safety guidelines, qualified monitored external
entrapment protection devices such as photoelectric sensors or edge sensors are required to be installed with this operator.
MPEL
Mounting Plate for Post
Mounting
For post mounting model
CSW24VDC commercial slide
operator. Posts not included.
29-NP712
7Ah 12V Battery
Standard 7 AMP-Hour Battery, 12
Vdc, to replace original batteries
provided with operator. Reuse
existing harnesses.
A12330SGLPK
33Ah 12V Battery
Upgrade 33 AMP-Hour
Battery, 12 Vdc. Ideal for solar
applications and extended
battery backup. Two required.
HTR
Heater Kit
Heater kit for pad mount
operators. Protects system to
-40ºF. Installs on operator frame.
MG1300
Magnetic Gate Lock
LiftMaster Elite Series®Maglock
(MG1300) Securely holds the
gate in the closed position
keeping unwanted visitors out.
(1300 lb holding force)
K75-50292
Swivel Arm
Swivel arm for uphill swing gate
applications.
10
SOLPNL20W12V
20 Watt 12V Solar Panel
Ideal for remote and sunny areas
without access to an AC outlet.
Two required.
SOLPNL10W12V
10 Watt 12V Solar Panel
Two required.
dwellingLIVE
Advanced Visitor
Management and Access
Control Solution
•Credentialed Access
•Visitor Management
•Telephone Entry Systems
•License Plate Recognition
•Community Websites
•Mobile Patrol
•Front Desk Concierge
11

Commercial DC
VEHICULAR SWING GATE OPERATOR
Model CSW24VDC Installation Blueprint
TYPICAL INSTALLATION OPERATOR POWER SOURCE
Wire Gauge 120 Vac 240 Vac
14 130 feet 260 feet
12 205 feet 410 feet
10 325 feet 650 feet
8 520 feet 1040 feet
6 825 feet 1650 feet
4 1312 feet 2624 feet
SAFETY LAYOUT
INSTALLATION DIMENSIONS
© 2014 LiftMaster All Rights Reserved
845 Larch Ave., Elmhurst, IL 60126
LiftMaster.com
01-37415B
DUAL GATE
Operator
Water Tight Conduit
(Not provided)
NOTE: Power and control wiring
MUST be run in separate conduits.
Earth Ground Rod
Check national and local
codes for proper depth
Warning Sign
Photoelectric
Sensors
Operator
Photoelectric
Sensors
Edge Sensor
Edge
Sensor
SINGLE GATE NOTE: Use copper conductors ONLY.
Water Tight Conduit
(Not provided)
NOTE: Power and control wiring
MUST be run in separate conduits.
Warning Sign
Earth Ground Rod
Check national and local
codes for proper depth
OPERATOR DIMENSIONS DETERMINE LOCATION FOR CONCRETE PAD AND OPERATOR
CONCRETE PAD AND OPERATOR ATTACHMENT
4 Concrete
Anchors
1/2" x 3 1/2"
Below the frost line.
Check all national and
local codes.
6" Above Ground
NOTE: One or more non-contact sensors shall be located where the risk
of entrapment or obstruction exists at either the opening or closing
direction. Care shall be exercised to reduce the risk of nuisance tripping,
such as when a vehicle, trips the sensor while the gate is still moving.
Monitored Photoelectric Sensors
Sensors for Close Cycle
(Inside Property)
(Outside Property)
NOTE: Entrapment protection is
required for the area between the
open gate and the operator.
Warning Sign
Operator
Edge
Sensor
27.66"
18.77" 14.8"
28"
24"
Outside Property
Inside Property
29.5"
35.5"
11"
2"
46"
25"
10"
Short Arm
Long Arm
Hinge Center
Concrete Pad
NOTE: There should only be a maximum of 4" (10.2 cm)
from the center of the hinge to the edge of the post or
column. If the distance is greater than 4" (10.2 cm)
entrapment protection for this area is required.
4" (10.2 cm) maximum
STANDARD INSTALLATION
CONDUIT LOCATION MOUNTING FOOTPRINT
5.5"
4.5" 1"
6.5" 4"
1.5" 10"
3"
28"
20"
15"
24"
13.6"
12.2"
6.1"
2.49"
14"
14.82"
(cover mounting distance)
(Conduit)
(Pad)
28"
24"
NOTE: Wired connection in
a dual gate setup is optional.
Operators can be setup for
wireless dual gate communication.