Chamberlain LA400 User manual

I N S T A L L A T I O N / O P E R A T I O N M A N U A L
Serial # Primary Arm
Serial # Secondary Arm
Serial # Control Box
Installation Date
2 YEAR WARRANTY
Radio Receiver
Built on Board
315MHz

Loop Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
Photo/Edge Inputs (P6-7-8 and 9) . . . . . . . . . . . . . . . . . . . . . . .32
Safety Accessories for Secondary Entrapment Protection . . . . .33
Operation 34
Reset Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
Manual Release . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
Maintenance 35-36
Battery Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
Basic Control Board Layout 37
Wiring Diagram 38
Troubleshooting 39-40
Repair Parts 41-42
LA400 Swing Gate Accessories 43
Warranty Policy and Service 44
When you see these Safety Symbols and Signal Words on the
following pages, they will alert you to the possibility of serious
injury or death if you do not comply with the warnings that
accompany them. The hazard may come from something
mechanical or from electric shock. Read the warnings carefully.
When you see this Signal Word on the following pages, it will
alert you to the possibility of damage to your gate and/or the gate
operator if you do not comply with the cautionary statements that
accompany it. Read them carefully.
Mechanical
Electrical
WARNING
CAUTION
IMPORTANT NOTE
• BEFORE attempting to install, operate or maintain the operator,
you must read and fully understand this manual and follow all
safety instructions.
• DO NOT attempt repair or service of your commercial door and
gate operator unless you are an Authorized Service Technician.
WARNING
TOOLS NEEDED FOR INSTALLATION
During assembly, installation and adjustment of the operator the
tools listed below will be needed.
• Wrench or Socket Set
• Phillips Head Screwdriver
• C Clamps
• Level
• Small Screwdriver
• T25 Torx Head Screwdriver
TABLE OF CONTENTS
INTRODUCTION
Introduction 2-5
Carton Inventory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Additional Items Needed for Installation . . . . . . . . . . . . . . . . . . .3
Operator Dimensions and Specifications . . . . . . . . . . . . . . . . . . .3
UL325 Classifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Safety Installation Information . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Overview of Typical Installation 6-10
Left-Hand Gate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Right-Hand Gate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Dual Gate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Safety Precautions for Swing and
Ornamental “Grill Type Gates” . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Warning Sign Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Before Installation Check Your Gate . . . . . . . . . . . . . . . . . . . . . . .9
Mounting Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Installation 11-18
Step 1: Manual Release . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Step 2A: Determine Position of the Pull-to-Open Bracket . . . . .12
Step 2B: Determine Position of the “Optional”
Push-to-Open Bracket (Not Provided) . . . . . . . . . . . . . . . . . . . .12
Step 3: Determine Mounting Location . . . . . . . . . . . . . . . . . . . .13
Step 4: Assemble Gate Post Bracket (Pull-to-Open) . . . . . . . . . .13
Step 5: Attach Bracket to Arm . . . . . . . . . . . . . . . . . . . . . . . . . .14
Step 6: Position Operator on Gate . . . . . . . . . . . . . . . . . . . . . . .14
Step 7: Test Gate Travel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Step 8: Secure Gate Post Bracket to Gate Post . . . . . . . . . . . . .16
Step 9: Secure Gate Bracket to Gate . . . . . . . . . . . . . . . . . . . . . .16
Step 10: Warning Sign Placement . . . . . . . . . . . . . . . . . . . . . . .17
Step 11: Open the Control Box . . . . . . . . . . . . . . . . . . . . . . . . . .18
Step 12: Select Mounting Holes . . . . . . . . . . . . . . . . . . . . . . . . .18
Step 13: Mount Control Box . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Motor Wiring 19-20
Step 1: Watertight Connector Nut . . . . . . . . . . . . . . . . . . . . . . .19
Step 2: Insert Operator Cable . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Step 3: Connect Operator to Control Board . . . . . . . . . . . . . . . .20
Power Wiring 21-22
Connect Transformer to Control Board . . . . . . . . . . . . . . . . . . .21
Earth Ground Rod Installation (Optional) . . . . . . . . . . . . . . . . . .22
Control Wiring 23
Adjusting/Running the Operator 24-26
Step 1: Set Dip Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Step 2: Program Limits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Step 3: Set Force/Bi-part/Timer . . . . . . . . . . . . . . . . . . . . . . . . .26
Optional Control and
Safety Device Wiring 27-33
To Add or Reprogram a Remote Control . . . . . . . . . . . . . . . . . .27
Dip Switch Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Wire Stop Button (Optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
2

3
HARDWARE KIT
DESCRIPTION QTY
Post Bracket 1
Pull to Open Bracket 1
Hex Bolt 5/16"-18 X 1-1/2" 5
Square Neck Carriage Bolt 3/8"-16 X 6" 2
Hex Nut 3/8"-16 2
Hex Nut 5/16"-18 5
Flat Washer 5/16" 5
Flat Washer 3/8" 5
Lock Washer 5/16" 5
Lock Washer 3/8" 5
Gate Mounting Bracket 1
Hairpin Clip 4
Pin 2
Hex Bolt 3/8"-16 X 1-1/2" 1
Bolt 2-3/4" 2
CONTROL BOX LA400 - CONT
DESCRIPTION QTY
Control Box 1
Hardware Bag 1
MISCELLANEOUS
Linear Actuator Arm
Motor Cable - Six Conductor 9' (2.7 m)
Warning Sign 2
Battery 2
Plug-In Transformer 1
LA400-S (SECOND LINEAR ACTUATOR ARM)
Extension Cable - Six Conductor 40' (12.2 m)
Junction Box - IP56 1
Phillips Head Mounting Screws 4
Anchors 4
Terminal Block - Twelve Connectors 1
NOTE: Carton inventory is based on a Single Operator. For Primary (Gate 1) and Secondary (Gate 2) installation the carton
inventory is doubled except for control box.
Operating Cycles 100 per day
Main Supply (Motor) 24Vdc
Current Consumption 2A
Power Consumption 48 Watts
Battery Charger Supply 26Vac, 29VA or 36Vdc, 40VA
Solar Panel Supply (Optional) See Accessories
Maximum Gate Width 16 ft. (4.9 m)
Maximum Gate Weight 550 Lbs. (249.5 kg)
Protection Class NEMA 3R
Travel Speed 14-18 seconds for a 90 degree opening
Rated Operating Time 4 Minutes
Temperature -20˚C to + 50˚C
-4˚F to + 122˚F
Main Supply (Control) Dedicated Circuit 120V~/60Hz
Absorbed Power 0.75 Watts
Protection Fuse Battery ATC 20A
Permanent fasteners for warning sign
Earth Ground Rod (Optional)
Power Wire: 120Vac (Stranded Copper Wire) Power Wire: 24Vac Transformer (Stranded Copper Wire)
Wire Gauge Length Wire Gauge Length
16 100' (30 m) 14 500' (152 m)
10 1000' (305 m) 12 1000' (305 m)
OR
36.3"
(92.1 cm)
.475" DIA.
(1.2 cm DIA.)
4.50"
(11.2 cm) .250"
(0.635 cm)
37.4"
(95.0 cm)
4.00"
(10.2 cm)
Weight: 13.2 lbs. (6 kg.)
Operator Dimensions and Specifications
Additional Items Needed for Installation
Carton Inventory
10"
(25.4 cm)
14"
(35.6 cm)
6"
(15.2 cm)

4
UL325 Model Classifications
The LA400 is intended for use with vehicular swing gates. The operator can be used in Class I, Class II and Class III applications.
CLASS I – RESIDENTIAL VEHICULAR GATE OPERATOR
A vehicular gate operator (or system) intended for use in a home of one-to four single family dwelling, or
a garage or parking area associated therewith.
CLASS II – COMMERCIAL/GENERAL ACCESS VEHICULAR GATE OPERATOR
A vehicular gate operator (or system) intended for use in a commercial location or building such as a
multi-family housing unit (five or more single family units) hotel, garages, retail store or other building
servicing the general public.
CLASS III – INDUSTRIAL/LIMITED ACCESS VEHICULAR GATE OPERATOR
A vehicular gate operator (or system) intended for use in a industrial location or building such as a
factory or loading dock area or other locations not intended to service the general public.
SAFETY ACCESSORY SELECTION
All UL325 compliant LiftMaster gate operators will accept external
entrapment protection devices to protect people from motorized
gate systems. UL325 requires that the type of entrapment
protection correctly matches each gate application. Below are the
four types of entrapment protection systems recognized by
UL325 for use on this operator.
ENTRAPMENT PROTECTION TYPES
Type A: Inherent obstruction sensing system, self-contained
within the operator. This system must sense and initiate
the reverse of the gate within two seconds of contact
with a solid object.
Type B1: Connections provided for a non-contact device, such as
a photoelectric eye can be used as a secondary
protection.
Type B2: Connections provided for a contact sensor. A contact
device such as a gate edge can be used for secondary
protection.
Type E: Built-in audio alarm. Examples include sirens, horns
or buzzers.
NOTE: UL requires that all installations must
have warning signs placed in plain view on
both sides of the gate to warn pedestrians of
the dangers of motorized gate systems.
UL325 ENTRAPMENT PROTECTION
REQUIREMENTS
The chart above illustrates the entrapment protection
requirements for each of the three UL325 classes.
In order to complete a proper installation you must satisfy the
entrapment protection chart shown above. That means that
the installation must have one primary means of entrapment
protection and one independent secondary means of
entrapment protection. Both primary and secondary
entrapment protection methods must be designed, arranged
or configured to protect against entrapments in both the open
and close directions of gate travel.
For Example: For a slide gate system that is installed on a
single-family residence (UL325 Class I) you must provide the
following: As your primary type of entrapment protection you
must provide Type A inherent (built into the operator)
entrapment sensing and at least one of the following as your
secondary entrapment protection: Type B1- Non-contact
sensors such as photoelectric eyes, Type B2- Contact sensors
such as gate edges.
Primary
Type
Class
I and II
Class III A, B1 or B2 A, B1,
B2 or E
A, B1 or
B2
A
UL325 Swing and Gate Barrier
Installation (Arm) Operator
Secondary
Type
Moving Gate Can Cause
Injury or Death
KEEP CLEAR! Gate may move at any
time without prior warning.
Do not let children operate the gate or
play in the gate area.
This entrance is for vehicles only.
Pedestrians must use separate entrance
Gate Operator Entrapment Protection
Class

5
Safety Installation Information
1. Vehicular gate systems provide convenience and security. Gate systems are comprised of many component parts. The gate operator is only
one component. Each gate system is specifically designed for an individual application.
2. Gate operating system designers, installers and users must take into account the possible hazards associated with each individual application.
Improperly designed, installed or maintained systems can create risks for the user as well as the bystander. Gate systems design and
installation must reduce public exposure to potential hazards.
3. A gate operator can create high levels of force in its function as a component part of a gate system. Therefore, safety features must be
incorporated into every design. Specific safety features include:
• Gate Edges • Guards for Exposed Rollers • Photoelectric Sensors
• Screen Mesh • Vertical Posts • Instructional and Precautionary Signage
4. Install the gate operator only when:
a. The operator is appropriate for the construction and the usage class of the gate.
b. All openings of a horizontal slide gate are guarded or screened from the bottom of the gate to a minimum of 4' (1.2 m) above the ground to
prevent a 2-1/4" (6 cm) diameter sphere from passing through the openings anywhere in the gate, and in that portion of the adjacent fence
that the gate covers in the open position.
c. All exposed pinch points are eliminated or guarded, and guarding is supplied for exposed rollers.
5. The operator is intended for installation only on gates used for vehicles. Pedestrians must be supplied with a separate access opening. The
pedestrian access opening shall be designed to promote pedestrian usage. Locate the gate such that persons will not come in contact with the
vehicular gate during the entire path of travel of the vehicular gate.
6. The gate must be installed in a location so that enough clearance is supplied between the gate and adjacent structures when opening and
closing to reduce the risk of entrapment. Swinging gates shall not open into public access areas.
7. The gate must be properly installed and work freely in both directions prior to the installation of the gate operator.
8. Controls intended for user activation must be located at least six feet (6') away from any moving part of the gate and where the user is
prevented from reaching over, under, around or through the gate to operate the controls. Outdoor or easily accessible controls shall have a
security feature to prevent unauthorized use.
9. The Stop and/or Reset (if provided separately) must be located in the line-of-sight of the gate. Activation of the reset control shall not cause the
operator to start.
10. A minimum of two (2) WARNING SIGNS shall be installed, one on each side of the gate where easily visible.
11. For a gate operator utilizing a non-contact sensor:
a. Reference owner’s manual regarding placement of non-contact sensor for each type of application.
b. Care shall be exercised to reduce the risk of nuisance tripping, such as when a vehicle trips the sensor while the gate is still moving.
c. One or more non-contact sensors shall be located where the risk of entrapment or obstruction exists, such as the perimeter reachable by a
moving gate or barrier.
12. For a gate operator utilizing a contact sensor such as an edge sensor:
a. One or more contact sensors shall be located where the risk of entrapment or obstruction exists, such as at the leading edge, trailing edge
and post mounted both inside and outside of a vehicular horizontal slide gate.
b. One or more contact sensors shall be located at the bottom edge of a vehicular vertical lift gate.
c. A hard wired contact sensor shall be located and its wiring arranged so the communication between the sensor and the gate operator is not
subject to mechanical damage.
d. A wireless contact sensor such as the one that transmits radio frequency (RF) signals to the gate operator for entrapment protection
functions shall be located where the transmission of the signals are not obstructed or impeded by building structures, natural landscaping or
similar obstruction. A wireless contact sensor shall function under the intended end-use conditions.
e. One or more contact sensors shall be located on the inside and outside leading edge of a swing gate. Additionally, if the bottom edge of a
swing gate is greater than 6" (152 mm) above the ground at any point in its arc of travel, one or more contact sensors shall be located on
the bottom edge.
f. One or more contact sensors shall be located at the bottom edge of a vertical barrier (arm).

6
Outside Property
Inside Property
Direction of
Gate ravel
MovingGate CanCause
Injury or Death
KEEPCLEAR!Gate may move atany
timewithoutprior warning.
Donot let children operate the gate or
playinthegate area.
Thisentrance is for vehicles only
Pedestriansmustuse separate entrance
T
MovingGate Can Cause
Injury or Death
KEEPCLEAR! Gate maymove atany
timewithout prior warning.
Donotlet children operate thegate or
playinthegate area.
Thisentranceisfor vehicles only
Pedestriansmust use separate entrance
OVERVIEW OF TYPICAL
INSTALLATION
NOTE: One or more non-contact sensors shall be located where the risk of entrapment or obstruction exists at either the
opening or closing direction. Care shall be exercised to reduce the risk of nuisance tripping, such as when a vehicle, trips
the sensor while the gate is still moving.
To prevent SERIOUS INJURY or DEATH; one or more
non-contact sensors shall be located where the risk of
entrapment or obstruction exists.
WARNING
Control Box
with Batteries
Antenna
Warning Sign
Hinge
Post Bracket
Operator
Gate Bracket
Entrapment Sensors
Power Cable
PVC Conduit (not provided) to
protect the power cable and low
voltage wire from lawn mowers
and string trimmers.
Left-Hand Gate
Right-Hand Gate
Warning Sign
Hinge
Antenna
Control Box
with Batteries
Power Cable
Operator
Post Bracket
PVC Conduit (not provided) to
protect the power cable and
low voltage wire from lawn
mowers and string trimmers.
Gate Bracket
Entrapment Sensors

7
Outside Property
Inside Property
Moving Gate Can Cause
InjuryorDeath
KEEPCLEAR! Gate may move at any
timewithout prior warning.
Donot let childrenoperate thegate or
playinthe gate area.
Thisentrance is for vehicles only
Pedestriansmustuse separate entrance
Direction of
Gate 1 ravel
TDirection of
Gate 2 ravel
T
Dual Gate Typical Installation
Entrapment Sensors
Entrapment Sensors
Warning Sign
Control Box
with Batteries
Antenna
Hinge
Post Bracket
Power Cable
PVC Conduit (not provided) to
protect the power cable and
low voltage wire from lawn
mowers and string trimmers.
Gate Bracket
Gate 1
Gate 2
Junction Box
Extension Cable

8
Moving Gate Can Cause
Injury or Death
KEEP CLEAR! Gate may move at any
time without prior warning.
Do not let children operate the gate or
play in the gate area.
This entrance is for vehicles only.
Pedestrians must use separate entrance
To prevent SERIOUS INJURY or DEATH from a moving gate:
• Install warning signs on EACH side of gate in PLAIN VIEW.
• Permanently secure each warning sign in a suitable manner
using fastening holes.
WARNING
To prevent SERIOUS INJURY or DEATH from a moving gate:
• Entrapment protection devices MUST be installed to protect
anyone who may come near a moving gate.
• Locate entrapment protection devices to protect in BOTH the
open and close gate cycles.
• Locate entrapment protection devices to protect between
moving gate and RIGID objects, such as posts.
• A swinging gate shall NOT open into public access ways.
WARNING
Warning Sign Placement
Safety Precautions for Swing and Ornamental “Grill Type Gates”

9
Before Installation Check Your Gate
Gate MUST swing freely and be supported entirely by it’s hinges. Heavy duty, ball
bearing type hinges are recommended.
Remove ANY/ALL wheels from the bottom of the gate Gate MUST NOT hit or drag across ground
Gate MUST be level
Gate and gate post MUST be plumb.

10
Mounting Options
Mounting locations vary depending on type and style of your gate. Minimum distance from the ground should not be less
than 4" from the bottom of the gate operator arm.
Recommended:
= Gate post bracket mounting locations
= Gate bracket mount locations
Optional:
= Gate post bracket mounting locations
= Gate bracket mount locations

INSTALLATION
11
Step 1: Manual Release
Insert the key into the lock and turn counter-clockwise 180°. Turn the release lever counter-clockwise 180°. The operator is
in manual mode.
Release Lever

12
Step 2A: Determine Position of the Pull-to-Open Bracket
The Pull-To-Open bracket can be assembled to work on a Left-Hand or a Right-Hand gate. Review the gate types below
and select the type of installation you will require.
NOTE: If the Pull-To-Open bracket is not assembled correctly you will damage the operator.
Step 2B: Determine Position of the “Optional” Push-to-Open Bracket
(Not provided. See Accessories.)
The Push-To-Open bracket can be assembled to work on a Left-Hand or a Right-Hand gate. Review the gate types below
and select the type of installation you will require.
Right-Hand Gate
Left-Hand Gate
Right-Hand Gate
Left-Hand Gate
Left-Hand Gate Right-Hand Gate
Right-Hand Gate
Left-Hand Gate

13
Step 4: Assemble Gate Post Bracket (Pull-to-Open)
Assemble Gate Post bracket by placing Pull-To-Open bracket on top of Post bracket. Insert bolt through both brackets
and secure with washer, lock washer and nut. Insert second bolt through both brackets and secure with washer, lock
washer and nut.
3/8" Hex Bolt
Pull-to-Open
Bracket
Post Bracket
3/8" Washer
3/8" Lock Washer
3/8" Nut
Pull-to-Open
Bracket
5/16" Hex Bolt
Post Bracket
5/16" Washer
5/16" Lock Washer
5/16" Nut
Step 3: Determine Mounting Location
The gate post bracket assembly can be mounted several places on the gate post. Refer to the illustrations on page 10
for the ideal mounting location.
Refer to the illustrations below to determine the appropriate dimensions for the Pull-To-Open bracket.
NOTE: It may be necessary to add shims (angle iron, sheets of metal or wood) to the gate post to achieve the required
dimensions.
Gate Post
Gate Hinge Point
7" (18 cm)
Operator
Hinge Point
7" (18 cm)
Gate Post
Gate Hinge Point
7" (18 cm)
Operator
Hinge Point
7" (18 cm)
Gate Post
Gate Hinge Point
7" (18 cm)
Operator
Hinge Point
7" (18 cm)
Gate Post
Gate Hinge Point
7" (18 cm)
Operator
Hinge Point
7" (18 cm)
Gate Post
Gate Hinge Point
7" (18 cm)
Operator
Hinge Point
7" (18 cm)
Gate Post
Gate Hinge Point
7" (18 cm)
Operator
Hinge Point
7" (18 cm)

14
NOTE: All the illustrations on the following pages display a typical Left-Hand Gate installation.
Step 5: Attach Brackets to Arm
Attach gate post bracket to arm using hex bolt and lock nut with nylon insert. Attach gate bracket to arm using pin and
hairpin clip.
Step 6: Position Operator on Gate
The gate post bracket assembly can be mounted several places on the gate post. Refer to the illustrations on page 10
for mounting options.
Place opener arm against gate post at the desired vertical position and temporarily secure Gate Post bracket with
C-clamp. Arm must be level.
Open gate to desired open position (no greater than 100°) and hold arm against gate. Mark mounting holes on gate
for reference.
Temporarily secure the gate bracket using a C-clamp.
Hex Bolt
Gate Post
Bracket
Pin
Gate Bracket
Hairpin
Clip
Hairpin
Clip

15
NOTE: If gate does not open and close completely adjust the position of the gate bracket and mark new mounting holes.
Ensure that the arm does not bind against the pull-to-open bracket.
Step 7: Test Gate Travel
Manually open and close the gate.
Ensure that the piston does not bottom out.
Do not allow piston to fully extend
or fully retract.
1/2" (1.3 cm)
1/2" (1.3 cm)

16
OR
OR
Step 8: Secure Gate Post Bracket to Gate Post
Mark holes for gate post bracket.
Remove C-clamp and operator. Set aside and drill adequate holes in gate post.
Secure gate post bracket to gate post using hardware. Keep arm level.
Step 9: Secure Gate Bracket to Gate
Drill holes in gate or reinforcement (if necessary) large enough for the gate bracket mounting
hardware. Secure gate bracket to gate using hardware (not provided). Keep arm level.
NOTE: Some installations may
require additional reinforcement
be installed on the gate.
Manually move the gate to verify gate opens and closes fully.
Carriage Bolts
Lock Washers
Hex Nuts
Flat Washers
Hex Nut
Flat Washer
Lock Washer
Gate Bracket
Hex Bolt
Arm
Angle
Iron
Wood
Flat
Bar
Reinforcement Area
Welder (Optional)
Welder (Optional)

17
If you are installing a 2nd operator repeat installation steps 1-10 for the second gate before proceeding to the next page.
Step 10: Warning Sign Placement
Moving Gate Can Cause
Injury or Death
KEEP CLEAR! Gate may move at any
time without prior warning.
Do not let children operate the gate or
play in the gate area.
This entrance is for vehicles only
Pedestrians must use separate entrance
Warning placards MUST be installed on both sides
of the gate and in plain view.
To prevent SERIOUS INJURY or DEATH from a moving gate:
• Install warning signs on the front and back of the gate
in PLAIN VIEW.
• Permanently secure each warning sign in a suitable manner
using fastening holes.
Fence
Gate Post
Gate
Inside
Property
Gate Travel
Path

18
Z22
R91
CLOSE
EDGE
R94
R92
R93
R1
R2
Z1
K5
K6
K2
F3
10A 32V
D1 Ø
OPEN EDGE/
PHOTO
OPEN
PHOTO
CLOSE
PHOTO
R227
R2 Ø 7
Z2 Ø
R223
P1
Z9
Z8
F2
F6
D4
D2
R9
C64
JMPR1
R224
U4
CONTROL
INPUTS
OPEN
SINGLE BUTTON
RESET
STOP
SHADOW
INTERRUPT
CHGR
OVLD
COM
COM
COM
FUSE
OPEN
LOOP
INPUTS
POWER
BATT 1BATT 2
F1 20A 32V
R35
D9
Z3
Z4
U3
D1
D27
F5
C11
C13
C12
D15
C2R4
R1
Ø 1
R1 ØØ
R9 Ø
Q9
K1
R196
Q22
D8
K3
K4
D21
D22 C4
ACCESSORY
OVLD
D6
JMPR2
MOV1
MOV2
DB1
U2
Z12
24 VAC/
SOLAR
INPUT
GATE 2
ACCESSORY
POWER
MAGLOCK
ALARM
GATE 1
C
C
NC
NO
NO
GRN
WHT
YEL
BLU
RED
BRN
GRN
WHT
YEL
BLU
RED
BRN
F4
10A 32V
F7
24V
COM
OVLD
TIMER
RUNNING
GATE 2
SET
OPEN
LIMIT
SET
CLOSE
LIMIT
LEARN
LIMITS
DIAGNOSTIC
GATE 1
J4
SINGLE
BUTTON
FORCE
BIPART
DELAY
TIMER TO
CLOSE
MIN MAX OFF MAX OFF MAX
L1
Ø 14GP Ø 89 Ø E
Ø 14LG Ø 89 Ø E
Ø 14SK Ø 89 Ø E
P2
J1
J19
S1
SAVE
MAGLOCK
MODE
EDGE
PHOTO
OFF
OFF
SINGLE
NO
NO
ON
ON
DUAL
NC
NC
LEARN
XMITTER
S8
1 2 3 4 5
O
N
2
1
SWITCHED
ACCESSORY
POWER
24V
OVLD
Step 12: Select Mounting Holes
Select holes to be used for mounting and knock out using a screwdriver and hammer.
Knock Outs
Knock Outs
Knock Outs
Knock Outs
Step 13: Mount Control Box
Secure control box to mounting surface (post, wall, column, etc.) using appropriate hardware.
Screws (4)
NOTE: It is recommended that the control box be mounted within 3' (.9 m) of Gate 1 or Gate 2.
Step 11: Open the Control Box
Remove screws and open the control box.
Knock Outs
Square Gate
Post
Screw
Round Gate
Post
Lock Washer
(Not Provided)
U Bolt
(Not Provided)
Washer
(Not Provided)
Hex Nut
(Not Provided)

19
To reduce the risk of SEVERE INJURY or DEATH:
• ANY maintenance to the operator or in the area near the
operator MUST not be performed until disconnecting the
electrical power and locking-out the power via the operator
power switch. Upon completion of maintenance the area MUST
be cleared and secured, at that time the unit may be returned
to service.
• Disconnect power at the fuse box BEFORE proceeding.
Operator MUST be properly grounded and connected in
accordance with local electrical codes. NOTE: The operator
should be on a separate fused line of adequate capacity.
• ALL electrical connections MUST be made by a qualified
individual.
• DO NOT install ANY wiring or attempt to run the operator
without consulting the wiring diagram. We recommend that
you install an optional reversing edge BEFORE proceeding with
the control station installation.
• ALL power wiring should be on a dedicated circuit and well
protected. The location of the power disconnect should be
visible and clearly labeled.
• ALL power and control wiring MUST be run in separate
conduit.
• BEFORE installing power wiring or control stations be sure to
follow ALL specifications and warnings described below.
Failure to do so may result in SEVERE INJURY to persons
and/or damage to operator.
WARNING
MOTOR WIRING
Z22
R91
CLOSE
EDGE
R94
R92
R93
L1
R1
R2
Z1
K5
K6
K2
F3
10A32V
D1
Ø
OPENEDGE/
PHOTO
OPEN
PHOTO
CLOSE
PHOTO
R227
R2 Ø 7
Z2 Ø
R223
P1
Z9
Z8
F2
F6
D4
D2
R9
C64
JMPR1
R224
U4
CONTROL
INPUTS
FORCE
TIMER TO
CLOSE
OFF MAX
OPEN
SINGLEBUTTON
RESET
STOP
SHADOW
INTERRUPT
CHGR
OVLD
COM
COM
COM
FUSE
OPEN
LOOP
INPUTS
POWER
BATT1BATT2
F1 20A32V
R35
D9
Z3
Z4
U3
D1
D27
F5
C11
C13
C12
D15
C2R4
R1
Ø 1
R1 ØØ
R9 Ø
Q9
K1
R196
Q22
D8
K3
K4
D21
D22 C4
ACCESSORY
OVLD
D6
JMPR2
MOV1
MOV2
DB1
U2
Z12
24VAC/
SOLAR
INPUT
GATE2
ACCESSORY
POWER
MAGLOCK
ALARM
GATE1
C
C
NC
NO
NO
GRN
WHT
YEL
BLU
RED
BRN
GRN
WHT
YEL
BLU
RED
BRN
F4
10A32V
F7
24V
COM
OVLD
TIMER
RUNNING
GATE2
SET
OPEN
LIMIT
SET
CLOSE
LIMIT
LEARN
LIMITS
DIAGNOSTIC
GATE1
J4
LEARN
XMITTER
MAGLOCK
ON OFF
L1
14GP 89
14LG 89
14SK 89
P2
J1
J19
S1
SAVE
MAGLOCK
MODE
EDGE
PHOTO
OFF
OFF
SINGLE
NO
NO
ON
ON
DUAL
NC
NC
LEARN
XMITTER
S8
1 2 3 4 5
24V
Step 2: Insert Operator Cable
Insert operator cable through watertight connector mounted in the bottom of the control box.
Step 1: Watertight Connector Nut
Insert operator cable through watertight connector nut.
Watertight
Connector
Nut
Operator
Cable
Operator
Control Box
Operator
Operator
Cable
Operator
Cable
Watertight
Connector
Nut
Watertight
Connector

20
Step 3: Connect Operator to Control Board
Extend cable and wires to “Gate 1” connector for single gate arm installation and connect as shown. Repeat
for “Gate 2” connector and connect as shown.
Z22
R91
CLOSE
EDGE
R94
R92
R93
R1
R2
Z1
K5
K6
K2
F3
10A32V
D1 Ø
OPEN EDGE/
PHOTO
OPEN
PHOTO
CLOSE
PHOTO
R227
R2 Ø 7
Z2 Ø
R223
P1
Z9
Z8
F2
F6
D4
D2
R9
C64
JMPR1
R224
U4
CONTROL
INPUTS
OPEN
SINGLE BUTTON
RESET
STOP
SHADOW
INTERRUPT
CHGR
OVLD
COM
COM
COM
FUSE
OPEN
LOOP
INPUTS
POWER
BATT1BATT2
F1 20A 32V
R35
D9
Z3
Z4
U3
D1
D27
F5
C11
C13
C12
D15
C2R4
R1
Ø 1
R1 ØØ
R9 Ø
Q9
K1
R196
Q22
D8
K3
K4
D21
D22 C4
ACCESSORY
OVLD
D6
JMPR2
MOV1
MOV2
DB1
U2
Z12
24 VAC/
SOLAR
INPUT
GATE2
ACCESSORY
POWER
MAGLOCK
ALARM
GATE1
C
C
NC
NO
NO
GRN
WHT
YEL
BLU
RED
BRN
GRN
WHT
YEL
BLU
RED
BRN
F4
10A32V
F7
24V
COM
OVLD
TIMER
RUNNING
GATE 2
SET
OPEN
LIMIT
SET
CLOSE
LIMIT
LEARN
LIMITS
DIAGNOSTIC
GATE 1
J4
R1
Z1
K2
F3
10A 32V
D1Ø
R9
Ø
Q
K1
Z12
ACCESSORY
POWER
GATE 1
C
NC
GRN
WHT
YEL
BLU
RED
BRN
GRN
BRN
24V
Brown
Green
White
Yellow
Blue
Red
L1
14GP 89
14LG 89
14SK 89
P2
J1
J19
S1
SAVE
MAGLOCK
MODE
EDGE
PHOTO
OFF
OFF
SINGLE
NO
NO
ON
ON
DUAL
NC
NC
LEARN
XMITTER
S8
1 2 3 4 5
SWITCHED
ACCESSORY
POWER
24V
OVLD
Z1
GATE 2
NC
GRN
WHT
YEL
BLU
RED
BRN
Brown
Green
White
Yellow
Blue
Red
ACCESSORY
POWER
24V
D15
C2R4 R196
10A 32V
NOTE: Wire connectors can be
removed to simplify wiring.
AUTOCALL
EXIT2
COM
EXIT1
HOUSETELCO
NOTE: Never allowoperator cable to drag on ground.
Gate 2
Gate 1
Control Box
Operator
Cable
“Gate 2”
Operator
Cable
“Gate 1” Watertight
Connector
Nut
Control Box
Operator
Cable
Operator