Chamberlain Clicker KLIK2U User manual

Universal Wireless Keypad
MODELS KLIK2U, KLIK2U-P2, KLIK2C AND KLIK2C-P2
Introduction . . . . . . . . . . . . . 2
Programming . . . . . . . . . . . 3-7
Installation. . . . . . . . . . . . . . 8
Changing your 4-digit PIN . . . 8
Battery. . . . . . . . . . . . . . . . . 8
FAQs . . . . . . . . . . . . . . . . . . 9

Introduction
Thank you for your purchase of the Universal Wireless Keypad.
PLEASE DO NOT RETURN TO THE RETAIL STORE. If for any reason you have
questions or need help with troubleshooting please call: 1-800-442-1255.
Read instructions thoroughly BEFORE beginning. If using this product
with residential door openers, this product must be used only with
door openers manufactured after 1993 that utilize photoelectric
sensors. The photoelectric sensors are always located on or near the
bottom of the door track.
WARNING: This product can expose you to chemicals including
lead, which are known to the State of California to cause cancer or
birth defects or other reproductive harm. For more information go to
www.P65Warnings.ca.gov
STOP
To prevent possible SERIOUS INJURY or DEATH from a moving gate or
garage door:
• Install keypad within sight of garage door, out of reach of small children at
a minimum height of 5 feet (1.5 m) above floors, landings, steps or any
other adjacent walking surface, and away from ALL moving parts of door.
• ALWAYS keep remote controls out of reach of children. NEVER permit
children to operate, or play with remote controls.
• Activate gate or door ONLY when it can be seen clearly, is properly
adjusted, and there are no obstructions to door travel.
• ALWAYS keep gate or garage door in sight until completely closed. NEVER
permit anyone to cross path of moving gate or door.

DETERMINE GARAGE DOOR OPENER TYPES:
Proceed with instructions according to your garage door opener type. NOTE: Your motor unit and/or remote control may look different.
TYPE 1
Chamberlain, Sears
Craftsman, LiftMaster,
Master Mechanic and Do It
garage door openers or
receivers with: 3 position
DIP switches.
Opener
Remote Control

TYPE 2
Genie, Linear and Moore-O-
Matic garage door openers or
receivers with: 2 position DIP
switches.
ON
ON
Opener
Remote Control

TYPE 3
Chamberlain, Sears
Craftsman, LiftMaster, Master
Mechanic and Do It garage
door openers or receivers
with: Yellow, white or grey
Smart/Learn buttons.
Opener
Remote Control

TYPE 4
Chamberlain, Sears
Craftsman, LiftMaster, Master
Mechanic, Do It, Genie
Intellicode, Overhead Door,
Stanley, Wayne Dalton or
Linear garage door openers
with: Smart/Learn button.
Opener

TYPE 5
Genie Intellicode 2 garage
door openers with: Program/
Set button.
BEFORE STARTING:
You MUST have a Genie
IntelliCode 2 remote control
with at least one button
already programmed to the
opener.
Opener

TYPE 1
Chamberlain, Sears Craftsman, LiftMaster,
Master Mechanic and Do It garage door
openers or receivers with: 3 position
DIP switches.
Select and write a 4-digit PIN:
__ __ __ __
Determine your opener ID using the list below.
The first DIP switch must be set to the “-” position on your remote and
opener. Record your DIP switch sequence for remaining DIP switches. If
the DIP switch is in the “+” position place a 1, “0” position place a 2, “-”
position place a 3 in the corresponding box in the chart below:
NOTE: Leave any unused switch locations blank.
1
Programming
2
3
DIP Switch
Sequence 123 4567 8 9
+
0
-3
Opener
Remote Control
ID DIP Switch Type
11 9 DIP switch garage door openers (U.S.)
12 9 DIP switch garage door openers (Canada)
15 8 DIP switch garage door openers
19 7 DIP switch garage door openers

If opener does not function, repeat programming.
Enter PIN from step 1, press #.
Enter ID from step 2, press #.
Enter DIP switch sequence from step
3 and press #key.
To test and use, wait until
lights turn off, enter your PIN
and press the 0key.
5
6
7
8
Press and hold the *and #buttons until keypad
stops flashing.
4

TYPE 2
Genie, Linear and Moore-O-Matic garage
door openers or receivers with: 2 position
DIP switches.
Select and write a 4-digit PIN:
__ __ __ __
Determine your opener ID using the list below.
Record your DIP switch sequence. If DIP switch is in the “on” or “up”
position place a 1, “off” or “down” position place a 2 in the corresponding
box in the chart below: NOTE: Leave any unused switch locations blank.
1
Programming
2
3
ON
ON
Opener
Remote Control
ID DIP Switch Type
13 12 DIP switch Genie garage door openers
14 10 DIP switch Linear garage door openers
16 10 DIP switch Stanley garage door openers
17 9 DIP switch Genie garage door openers
18 8 DIP switch Linear, Moore-O-Matic garage door
openers
DIP Switch
Sequence 123456789101112
ON
OFF

If opener does not function, flip DIP switches, so if a switch is “on” or “up”
flip it “off” or “down” in step 3.
Enter PIN from step 1, press #.
Enter ID from step 2, press #.
Enter DIP switch sequence from step
3 and press #key.
To test and use, wait until
lights turn off, enter your PIN
and press the 0key.
5
6
7
8
Press and hold the *and #buttons until keypad
stops flashing.
4

TYPE 3
Chamberlain, Sears Craftsman, LiftMaster,
Master Mechanic and Do It garage door
openers or receivers with: Yellow, white or
grey Smart/Learn buttons.
Select and write a 4-digit PIN:
__ __ __ __
Your opener ID is 11.
1 1
Record your DIP switch sequence. Set your first DIP switch to “-”, your
first DIP switch must be set to the “-” position on your remote and
opener. If the DIP switch is in the “+” position place a 1, “0” position
place a 2, “-” position place a 3 in the corresponding box in the chart
below: NOTE: Leave any unused switch locations blank.
1
Programming
2
3
Opener
Remote Control
DIP Switch
Sequence 123 4567 8 9
+
0
-3

If opener does not function, repeat programming.
Enter PIN from step 1, press #.
Enter 11, press #.
Enter DIP switch sequence from step
3, press #.
Press and release the Smart/Learn
button on garage door opener.
Enter your 4 digit PIN and press the 0key.
To test and use, wait until
lights turn off, enter your PIN
and press the 0key.
5
6
7
8
9
10
Press and hold the *and #buttons until keypad
stops flashing.
4

TYPE 4
Chamberlain, Sears Craftsman, LiftMaster,
Master Mechanic, Do It, Genie Intellicode,
Overhead Door, Stanley, Wayne Dalton or
Linear garage door openers with: Smart/
Learn button.
Select and write a 4-digit PIN:
__ __ __ __
1
Programming
Opener
Determine your opener ID using the list below.
2
ID Garage door opener brand and manufacturing dates
1Linear garage door openers manufactured from 1997 to present.
2Chamberlain, Sears Craftsman, LiftMaster, Master Mechanic and
Do It garage door openers manufactured from 1997 to 2004
[Orange/Red Button].
3Chamberlain, Sears Craftsman, LiftMaster, Master Mechanic and
Do It garage door openers manufactured from 2005 to present
[Purple Button].
4Chamberlain, Sears Craftsman, LiftMaster, Master Mechanic and
Do It garage door openers manufactured from 1993 to 1996
[Green Button].
5Genie Intellicode and Overhead Door garage door openers
manufactured from 2005 to present (315 MHz).
6Genie Intellicode and Overhead Door garage door openers
manufactured from 1995 to present (390 MHz).
7Stanley garage door openers manufactured in 1998 to present.
8Chamberlain, Sears Craftsman, and LiftMaster garage door
openers manufactured 2011 to present [Yellow Button].
9Wayne Dalton garage door openers manufactured in 1999 to
present.

If opener does not function, repeat programming.
Enter PIN from step 1, press #.
Enter ID from step 2, press #.
Press and release the Smart/Learn
button on garage door opener.
Enter your 4 digit PIN and press the 0key. NOTE:
For Genie and Overhead Door units, press the 0
key twice.
To test and use, wait until
lights turn off, enter your PIN
and press the 0key.
4
5
6
7
8
Press and hold the *and #buttons until keypad
stops flashing.
3

7
TYPE 5
Genie Intellicode 2 garage door openers
with: Program/Set button.
Select and write a 4-digit PIN:
__ __ __ __
1
Programming
Opener
2
Enter PIN from step 1, press #.
Press 5, then press #.
On the garage door opener, press
and hold the Program/Set button
until both the long and short LED
light up BLUE.
Release the Program/Set button and
only the round LED will be lit in
BLUE.
4
5
6
Press and hold the *and #buttons
until keypad stops flashing.
3

7If opener does not function, repeat programming.
Press and release the Program/Set
button and the long LED will flash
PURPLE.
On the CLICKER®keypad, press
and release 0again. Both LEDs on
the garage door opener will light
up BLUE.
On the Genie®remote control,
press and release the button that is
already programmed to the garage
door opener. Both LEDs will flash
PURPLE.
On the CLICKER®keypad, enter
the PIN from step 1, and press
and release the 0key. Both LEDs
on the garage door opener will
light up PURPLE.
On the CLICKER®keypad,
press and release 0again.
This will activate the garage
door opener and
programming is complete.
7
10
8
9
11
To test and use, wait 30 seconds, then enter
your PIN and press the 0key.
12

8
Installation
Remove cover.
1
Remove battery cover to expose mounting holes.
2
Remove battery and mount keypad using screws provided.
3
Reassemble.
4
Install out of reach of small children at a minimum height of 5 feet (1.5 m) above
floors, landings, steps or any other adjacent walking surface, and away from ALL
moving parts of door. Secure keypad to a smooth surface. Mount the keypad out
of the path of the moving garage door, but within sight of it (4" [10 cm]
clearance is needed for the cover).
Changing your 4-digit pin
Enter existing PIN, press *, enter new PIN and press *.
To test and use, enter your new PIN and press the 0key.

8
Battery
Replace the 9-Volt battery when keypad light
becomes dim or does not light up. Slide cover up,
remove battery cover, and replace battery.
Re-programming may be necessary.
9V Battery
To prevent possible SERIOUS INJURY or DEATH:
• NEVER allow small children near batteries.
• If battery is swallowed, immediately notify doctor.
1
2
3

FAQs
Why won’t my keypad work?
• Did the keypad lights come on when you entered your PIN? If the keypad
lights do not turn on when you press a button, it indicates that the battery
needs to be replaced. Replace with a 9V battery.
• Try reprogramming the keypad to the garage door opener.
• Make sure the keypad is compatible with your garage door opener
(Chamberlain 315 MHz or 390 MHz garage door openers manufactured after
January 1, 1993).
• If the solutions above did not work, replace the keypad.
How do I erase my pin?
To clear out the keypad, press and hold the * and the # keys together until the
keypad stops flashing. Proceed to reprogram the keyless entry.
Can I program the keypad to a second garage door opener?
The keypad can only activate one garage door opener.
Do I always have to use a 0 after my 4 digit PIN to activate the opener?
After programming the keypad, any fifth number will act as the “enter” button
to activate the opener.
Why does the door move after I only press 1 number button?
After operating the garage door with the keypad, the keypad lights will flash for
10 seconds. The keypad remains active during the 10 seconds of flashing; any
number will activate the door.
Where is my LEARN button located?
If equipped with a LEARN button, it can either be found on the garage door
opener or on an external receiver. To locate the receiver look for an antenna.
Some receivers will require a cover be removed to gain access to the
switch positions.
Will I have to reprogram the keypad after changing the battery?
The keypad should retain its memory. If the keypad no longer operates the
operator, reprogram the keypad to your system.
Where is my LEARN button on my gate?
Most gate operators have a built-in radio receiver or an external receiver. The
receiver on a gate opener can usually be found within the cabinet of the
operator. To gain access you might require permission if used in a
community gate.
WARRANTY
ONE YEAR LIMITED WARRANTY
The Chamberlain Group, Inc. warrants to the first consumer purchaser of this
product that it is free from defect in materials and/or workmanship for a period
of 1 year from the date of purchase.
NOTICE: To comply with FCC and or Industry Canada (IC) rules, adjustment or modifications
of this receiver and/or transmitter are prohibited, except for changing the code setting or
replacing the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.
Tested to Comply with FCC Standards for Home or office use. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2)this
device must accept any interference received, including interference that may cause undesired
operation.
www.chamberlain.com
1-800-442-1255