Chamberlain LiftMaster ELITE EL25 User manual

Quickstart
EL25 Keypad Programming Guide
EL25 Keypad Programming Guide
Telephone entry/access control system with a 25 directory code capacity
®
™
© 2005 The Chamberlain Group, Inc.
All Rights Reserved
Quickstart
This Quickstart Guide is intended to highlight some applications. These instructions are not intended to be
comprehensive. Please consult the Keypad Programming Manual for complete information.

Page 1
Programming
Number
Factory
Setting
Description of Task Programming Procedure
***
12 # Enable/Disable True Anti-Passback (0 = disable;
1 = enable) # Enable/Disable Timed Anti-Passback (0
= disable; 1 = enable) #
15 # (0 – 1; 0 = one long ring, 1 = double ring) #
14 # (1 – 9) #
Disabled
11 Enable/Disable Unlock Time Zone 11 # (0 = disable; 1 = enable) #
Enable/Disable Real-Time Monitoring
Set Maximum Number of Rings
Allowed Before Aborting Attempt
Set “Strikes” and “Out”
Enable/Disable Direct Commands
24 24 # (0 = disable; 1 = enable) #
Enabled
Enable/Disable Access Granted Beeps
23 23 # (0 = disable; 1 = enable) #
Disabled
Enable/Disable Voice Mail
22 22 # (0 = disable; 1 = enable) #
Enabled
21 21 # (0 = disable; 1 enable) #
Enable/Disable the Telco Mode Enabled
Enabled
10 Enable/Disable Do Not Disturb Schedule 10 # (directory code) # (0 = disable; 1 = enable) #
Disabled
20 20 # (0 = disable; 1 = enable) #
Set Microphone Volume 5
19 19 # (0 = mute; 1-10, 1 is low and 10 is high) #
Set Speaker Volume 5
18 18 # (0 = mute; 1-10, 1 is low and 10 is high) #
3 Errors
17 17 # (max errors, 0-5) #
Number of Rings Before Unit Answers 5 Rings
5 Rings
0 = One
Long Ring
16
Set Standard Single Ring or Double
Ring Response
15
14
16 # (0 – 15) # Each unit in chain must have same setting
Set Anti-Passback Time 3 Minutes
9Enable/Disable Call Waiting 9 # (0 = disable; 1 = enable) #
Enabled
Set Entry Code Length
77 # (3-9) #
4 Digits
Set Directory Code Length
66 # (1 or 2) #
2 Digits
Set Visitor Talk Time
55 # (15 – 250 seconds) #
60 Seconds
Enable/Disable Daylight Savings Time
44 # (0 = disable; 1 = enable) #
Enabled
Set the Clock
33 # yymmdd # (day of the week) # hhmm #
Set Unit ID Number and No. in Chain
2
2 # (unit ID number, 1-7) # (Number of Units in Chain, 1-7) #
Unit ID 1, Chain No. 1
Change or Verify the Unit's Password
11 # (1 to change; 2 to verify) # (six-digit code) #
000000
Exiting Programming Mode
Entering Programming Mode
00 #
*** (6 Digit Password)
13
Enable/Disable Anti-Passback Disabled
12
13 # (1-60 minutes) #
The Pound Key (#) must be used as Data Field Separator and to Save Data at the end of the sequence.
Time must be entered using a 24-hour format
(8AM=0800, 3PM=1500 etc. )
2 Short Beeps: Programming input is valid. 1 Long Beep: Input is not valid.
If you make an error during an entry, press the asterisk key (*) to begin again.
Important:
Guide for Programming the EL25
Optional Steps Indicated with a Background, all other steps are Required

Page 2
Programming
Number
30
30 # (time zone number, 2-63) # (segment number;
99) # (starting time = hhmm; 99) # (ending time =
hhmm) # (day of week, 1-8; 1 = Sunday; 7 = Saturday;
8 = holiday) #
Create a Time Zone
29 Reset the Unit
31 # (door 1-4) # (time zone, 2-63; 99) #
31
Assign Door Auto Lock/Unlock Time Zone
Disabled
Factory
Setting
Description of Task Programming Procedure
41 Add or Edit a Full Function Directory
Code
40 40 # (directory code) # (phone number) # (phone
extension) #
32 # (1 = add, 2 = verify, 0 = delete) # (yymmdd;
yy = year, mm = month, dd = day of the month) #
Add a Basic Directory Code
32 Setting Holidays
29 # 101010 #
28 Restore Factory Settings 28 # 101010 #
Verify an Entry Code
55
Activate/Deactivate an Entry Code
56
55 # (entry code) #
Change an Entry Code ONLY
54 54 # (entry code to change) # (new entry code) #
Activate/Deactivate a Directory Code
45
Enable/Disable Call Forwarding
(Directory Calls)
46 Disabled
Disabled
Delete a Directory Code
Enable/Disable Call Forwarding and Do
Not Disturb Schedule with Residence
“Call” Button Only
48
49
48 # (directory code) #
Verify a Directory Code
47 47 # (directory code) #
Add a Basic Entry Code
50
Add/Edit a Full Function Entry Code
51
50 # (entry code) #
To enter programming mode from the EL25:
Press *** and the 6-Digit Password (2 short beeps will be heard)
Exiting programming mode allows changes to take effect
44 # (new directory code) # (directory code to change) #
Change a Directory Code ONLY
44
Optional Steps Indicated with a Background, all other steps are Required
41 # (directory code) # (phone number) # (phone ext)
# (DnD schedule number, 0-63) # (enable/disable call
fwd) # (call fwd schedule number, 0-63) # (new call
fwd phone number) # (call fwd phone ext) #
46 # (directory code) # (0 = disable; 1 = enable)
(schedule number, 0-63) # (new call forward phone
number) # (call forward phone extension) #
49# DnD Enable (1)/Disable (0) # DnD Schedule (0-
63) # Call Forward Enable/Disable (0 = disable; 1 =
enable) # Call Forward Schedule (schedule number,
0-63 # (new call forward phone number) #
(call forward phone extension) # (call forward
extension delay, 0 to 30 sec.) #
51 # (entry code) # (schedule for door 1, 0-63) #
(schedule for door 2, 0-63) # (schedule for door 3,
0-63) # (schedule for door 4, 0-63) #
56 # (entry code) # (0 = deactivate; 1 activate) # (0 =
don't use start; 1 = use start) # (Start Date = yymmdd)
# (Start Time = hhmm) # (0 = don't use end; 1 = use
end) # (End Date = yymmdd) # (End Time = hhmm) #
45 # (directory code) # (0 = deactivate; 1 activate) #
(0 = don't use start; 1 = use start) # (Start Date =
yymmdd) # (Start Time = hhmm) # (0 = don't use
end; 1 = use end) # (End Date = yymmdd) # (End
Time = hhmm) #

Page 3
Factory
Setting
Description of Task Programming Procedure
Programming
Number
61 # (door 1-4) # (relays to activate 0000-1111) #
Order of relay is: relay 4 – relay 3 – relay 2 – relay 1 for an
example if you want relay 4 active you would enter 1000, if
you want relay 1 active you would enter 0001
60 # (device 1-4) # (device type 0-2; 0 = no device,
1 = wiegand card reader or keypad, 2 = RF receiver) #
(door 1-4) #
Delete an Entry Code
57
Assign Each External Access Control
Device a “Door Number”
(Step 1 of 4)
60
Assign “Each” Door Number to One or
More Relays
(Step 4 of 4)
61
Assign Door Use Time Zone
63
57 # (entry code) #
Set the Default Facility Code
73 73 # (0-255) #
Set the Default Card Type
71 71 # (26 or 30) #
Set Relay(s) for AutoCall
70
Assign a Postal Lock Switch to Door No.
69 69 # (door 0-4; 0 = no postal lock) #
70 # (relays to activate 0000-1111) #
Order of relays are 4321
63 # (door 1-4) # (time zone, 0-63) #
D1,D2,D3,D4=Enabled
No Device
Assigned
No Relays
Assigned
D1=Relay 1
D2=Relay 2
D3=Relay 3
D4=Relay 4
64
64 # (device 0-4) # (0-3; 0 = disable,
1 = set device to timed anti-passback,
2 = set device to true anti-passback - entrance,
3 = set device for true anti-passback - exit) #
Set Anti-Passback Entry/Exit for
Specific Devices
74 74 # (0 = disable; 1 = ignore) #
66 # (relay number 1-4) # (activation time, 1-300
seconds) #
Enable/Ignore Facility Code when Card is Used
66 Set Each Relay's “Activation Time”
(Step 3 of 4)
80 Add a Basic Card
81 Add or Edit a Full Function Card
67 Configure an Exit Device (REX)
Disabled
All Relays =“Strike”
All Relays =
10 seconds
R1=Door 1
R2=Door 2
R3=Door 3
R4=Door 4
68 Configure a Door Sensing Device
82 Add a Card Group
DS1=Door 1
DS2=Door 2
DS3=Door 3
DS4=Door 4
Set Each “Relay Type” to get the
Appropriate Response
(Step 2 of 4)
65 65 # (relay 1-4) # (0-5; 0 = unknown, 1 = strike,
2 = shunt, 3 = CCTV, 4 = alarm, 5 = control) #
Door 1
30-bit Cards
0
Ignored
The Pound Key (#) must be used as Data Field Separator and to Save Data at the end of the sequence.
Time must be entered using a 24-hour format (8AM=0800, 3PM=1500 etc. )
2 Short Beeps: Programming input is valid. 1 Long Beep: Input is not valid.
If you make an error during an entry, press the asterisk key (*) to begin again.
Important:
Optional Steps Indicated with a Background, all other steps are Required
67 # (REX number 1-4) # (select REX option: 0 =
disabled, 1 = use your door settings or 2 = use
specific relay(s) 0000-1111) #
Order of Relays are 4321
68 # (sensor number 1-4) # (select sensor option: 0 =
disabled, 1 = use your door settings or 2 = use
specific relay(s) 0000-1111) #
Order of Relays are 4321
80 # (card PIN code) # (facility code) # (card type, 26
or 30) #
81 # (card PIN code) # (facility code) # (card type, 26
or 30) # (schedule for door 1, 0-63) # (schedule for
door 2, 0-63) # (schedule for door 3, 0-63) #
(schedule for door 4, 0-63) #
82 # (card PIN code start range) # (card PIN code
end range) # (facility code) # (card type, 26 or 30) #
(0 = deactivate; 1 = activate) # (schedule for door 1,
0-63) # (schedule for door 2, 0-63) # (schedule for
door 3, 0-63) # (schedule for door 4, 0-63) #

Page 4
Factory
Setting
Description of Task Programming Procedure
Programming
Number
86 Verify a Card
85 Replace a Card
88 Delete a Card
90 Add a Basic Transmitter 90 # (transmitter PIN code) # (facility code) #
(sequence number) # (ID number) # (button number) #
87 Activate or Deactivate a Card
91 Add or Edit a Full Function Transmitter
Configure “Door Held Open” Alarm
Feature
102 # (alarm option; 0 = disable, 1 = enable until
relay time expires, 2 = enable until alarm clears) #
(relay group, 0000-1111) #
Order of relays is 4321
Configure “Door Forced Open” Alarm
Feature
103 # (alarm option; 0 = disable, 1 = enable until
relay time expires, 2 = enable until alarm clears) #
(relay group, 0000-1111) #
Order of relays is 4321
96 Verify a Transmitter
96 # (transmitter PIN code) # (facility code) #
(sequence number) # (ID number) # (button number) #
94 Add a Group of Transmitters at Once
95 # (transmitter PIN to change) # (facility code) #
(sequence number) # (ID number) # (button number)
# (new transmitter PIN) # (new facility code) # (new
sequence number) # (new ID number) # (new button
number) #
95 Replace a Lost Transmitter
100
102
103
Deactivate a Button on a Transmitter
and/or Delete a Transmitter
100 # (transmitter PIN code) # (facility code) #
(sequence number) # (ID number) # (button number) #
98 Activate or Deactivate a Transmitter
Disabled
Disabled
Optional Steps Indicated with a Background, all other steps are Required
85 # (lost or stolen card PIN code) # (facility code) #
(card type, 26 or 30) # (new card PIN) # (new facility
code) # (new card type, 26 or 30) #
86 # (card PIN code) # (facility code) # (card type, 26
or 30)
87 # (card PIN code) # (facility code) # (card type, 26
or 30) # (0 = deactivate; 1 = activate) # (0 = don't use
start; 1 = use start) # (Start Date = yymmdd) # (Start
Time = hhmm) # (0 = don't use end; 1 = use end) #
(End Date = yymmdd) # (End Time = hhmm) #
88 # (card PIN code) # (facility code) # (card type, 26
or 30) #
91 # (transmitter PIN code) # (facility code) #
(sequence number) # (ID number) # (button number)
# (schedule for door 1, 0-63) # (schedule for door 2,
0-63) # (schedule for door 3, 0-63) # (schedule for
door 4, 0-63) #
94 # (transmitter PIN code start range) # (transmitter
PIN code end range) # (facility code) # (sequence
number) # (ID number) # (button number) #
(0 = deactivate; 1 activate) # (schedule for door 1,
0-63) # (schedule for door 2, 0-63) # (schedule for
door 3, 0-63) # (schedule for door 4, 0-63) #
98 # (transmitter PIN code) # (facility code) #
(sequence number) # (ID number) # (button number)
# (0 = deactivate; 1 activate) # (0 = don't use start; 1 =
use start) #(Start Date = yymmdd) # (Start Time =
hhmm) # (0 = don't use end; 1 = use end) #(End Date
= yymmdd) # (End Time = hhmm) #

Page 5
Factory
Setting
Description of Task Programming Procedure
Programming
Number
Verify Multi-Unit Number 111 #
105 Enable or Disable Anti-Passback
Forgiveness at Midnight 105 # (0 = disable; 1 = enable) #
Change the Visitor Call Response Keys
116 9, 5, 3, 7, 2, 1,*
Enabled
109 Override Telephone Company
Answering Service 109 # (0 = no; 1 = yes) #
Default is “No”
No
110
111
Dial “0-9” First to Get an Outside Line
Using a Automated Phone System
113 # (0 = disable; 1 = enable) # (0-9, when enabled) #
113
Set a Phone Number's Extension Delay
Time No Delay
Set Alternative Prefixes 115 # (normal-00, mixed-01, asterisk-02, pound-03,
number-1n) #
each unit in chain must have same setting
115 Normal
Talk through the EL25 Speaker 120 #
120
Cycle Door 121 # (door 1-4) #
121
Latch Door “Open” Until... 122 # (door 1-4) # (end time = hhmm) #
122
Latch Door “Closed” Until... 123 # (door 1-4) # (end time = hhmm) #
123
Release Door “Now” 124 # (door 1-4) #
124
Cycle Relay “Now” 131 # (relay 1-4) #
131
Delete ALL Directory Codes 201 # 101010 #
201
Delete ALL Entry Codes 202 # 101010 #
202
Delete ALL Access Cards 203 # 101010 #
203
Delete ALL Transmitter Codes 204 # 101010 #
204
Delete ALL Time Zones 205 # 101010 #
205
Delete ALL Access Codes from Database
206 # 101010 #
206
To enter programming mode from the EL25:
Press *** and the 6-Digit Password (2 short beeps will be heard)
Exiting programming mode allows changes to take effect
The Pound Key (#) must be used as Data Field Separator and to Save Data at the end of the sequence.
Time must be entered using a 24-hour format (8AM=0800, 3PM=1500 etc. )
2 Short Beeps: Programming input is valid. 1 Long Beep: Input is not valid.
If you make an error during an entry, press the asterisk key (*) to begin again.
Important:
Optional Steps Indicated with a Background, all other steps are Required
110 # (directory code) # (phone extension delay) #
(call forward extension delay) #
116 # (activate door 1) # (activate door 2) # (activate
door 3) # (activate door 4) # (call wait toggle) #
(extend talk time) # (hang up and deny access) #
Configure “Strikes and Out” Alarm
Feature
104 # (alarm option; 0 = disable, 1 = enable until
relay time expires, 2 = enable until alarm clears) #
(relay group, 0000-1111) #
Order of relays is 4321
104 Disabled
Disabled

Page 6
Programming Basics
Programming Single Unit Overview
Programming Single Unit Overview
11, 2 or 3 digit Programming Number. (See “ Quick Reference Guide ” Tables for descriptions and procedures)
2One or more Data Fields.
3Pound Key (#) as a Data Field Separator and at the
end of the programming sequence to Save the Data .
•
•
•
•
EL25 Keypad: You may use the keypad on the front panel. (Next Page)
Local/Remote DTMF Phone: You may use the keypad on a local or remote phone to program the system. The unit
responds to the DTMF signals generated by your touch-tone phone. (Next Page)
Direct/Modem Connection to a PC: In order to program the EL25 with a direct or modem connection, your PC must be
running Sentex's Windows®-compatible Versa XS software. (Not covered in this Quickstart Guide)
1st Pound Key:
Separates the 1st field. Last Pound Key:
Saves the data.
Data Field:
1 changes the password
(2 verifies the password)
Data Field:
(The new password)
Programming Number:
changes or verifies
the password.
Enter
Programming
Mode
(Next page)
Exit
Programming
Mode
(Next page)
The EL25 can be programmed 3 different ways.
1
2
3
THIS guide will outline some programming for the EL25 from the keypad or
local/remote DTMF (Touch-Tone) phone ONLY.
For more information, refer to the Manuals and/or your installation dealer.
All data fields must be separated with the pound key (#).
( Programming Number) # (Data Field) # (Data Field) # (Data Field) #
Steps tagged with a ( ) are
optional , press the pound key (#) to skip them. Note: Some steps are required
and must have data entered in them to continue, tagged with ( ).
If you make an error during an entry, press the asterisk key (*) to cancel the step.
When you
correctly enter the entire programming sequence, the unit will respond with 2 short beeps
(see also System Feedback/Responses (Beeps)).
If you make an error during an entry, press the asterisk key (*) to begin again.
Notes:
Example of a Programming Sequence: “ Changing the Password”
Pound Key:
Separates the data field.
Programming Single Unit Overview
1
1
Procedure Required to Program the EL25:
#
#
2 short
beeps
1 3 4
2
Optional StepRequired Step Required Step Required Step
Example:
Required Step
Optional Step,
Press (#) to Skip.

Page 7
Enter Programming Mode
Exit Programming Mode
1 Press
2 Enter the (6) six-digit password. The default is six zeroes.
If you will be programming the unit via modem, please refer to the Versa XS online help.
After entering programming mode for the first time, we suggest you change
the password to maintain the security of your system.
Important:
The unit is now ready to accept programming instructions!
1 When you hear the dial tone, press
If multiple EL25 units are sharing the same phone line, then a Unit ID Code (1-7) will need
to be entered at this time.
1 Dial the unit's phone number.
2 When the EL25 picks up the call, you will hear 2 beeps.
3 Press
The unit is now ready to accept programming instructions!
1A
3A If multiple EL25 units are sharing the same phone line, then a Unit ID Code (1-7) will need
to be entered at this time.
2 Enter the (6) six-digit password. The default is six zeroes.
3 Press and the tone will stop.
The unit is now ready to accept programming instructions!
4 Enter the (6) six-digit password. The default is six zeroes.
5 Press
Press on the EL25 keypad and the unit will respond with
3 short beeps when disconnecting.
Press on the telephone and the unit will respond with
3 short beeps when disconnecting.
and the beeps will stop.
Note: If the EL25 and an answering machine (or answering service) utilize the same phone line, let the line
ring at least (2) two times, hang-up, and call back within one (1) minute. The EL25 will answer on the
second call. If the unit does not answer, you may need to change the ring count.
Press when using a
telephone or the EL25 to cancel
programming sequence and exit programming mode.
•
•
Programming Single Unit Overview
Programming Single Unit Overview
0
***
From the Remote Telephone:
From the Residence Telephone:
From the EL25 Keypad:
2 Short Beeps
1
2
2

Page 8
System Feedback / Responses (Beeps)
2 Short Beeps: Programming step was valid.
3 Short Beeps: Programming mode was exited.
1 Long Beep: Input was not valid.
2 Long Beeps: Duplicate entry code was entered.
3 Long Beeps: Memory is full.
4 Long Beeps: Unit has reset or is powering up.
Busy Signal: Line is busy or Do Not Disturb feature is in effect.
The EL25 emits various audio tones to respond to input and to indicate certain conditions.
1 Short Beep: Key was pressed on the unit's keypad.
1 Beep: Talk time for a visitor call is lapsing and the unit will beep once per second for the
last 10 seconds unless the talk time is extended.
Ring Back: The unit is ringing the building.
10 Short Beeps: The unit has granted access.
Silence: The keypad has struck out, the unit is being programmed from
another source, or an alarm condition exists.
5 Short Beeps: Gate is closing by command.
10 Short Beeps Gate is opening by command.
1 Lift the receiver and press
Enters direct command mode Enters direct command mode for unit three
The unit is now ready to allow direct commands only!
(NPBI / Single Family Residence ONLY)
1A If multiple EL25 units are sharing the same phone line, then a Unit ID Code (1-7) will need
to be entered at this time.
Example 1: Example 2:
You can send commands directly to the EL25 from your phone without being in programming mode.
This feature is only available for a single-family residence or a manager is sharing a phone line
with the EL25.
Programming Single Unit Overview
Programming Single Unit Overview
Programming Responses:
Direct Command Responses:
Other Responses:
To Enter a Direct Command from a Residence Phone:
Sending Direct Commands from the Resident's Phone

Page 9
Programming Multiple Units Overview
Note: You cannot program a unit within a multi-unit chain from a local/remote DTMF phone (Touch-Tone) unless
you know the unit's ID number. Therefore, you can only verify the unit number while programming from the unit's
front keypad.
Up to seven (7) EL25s can be installed on a single telephone line. Each unit must have a “ Unique
Unit ID”
number and the “Number of Units in Chain” assigned to it.
If you make an error during an entry, press the asterisk key (*) to begin again.
Then
Then
1 Press
2 Unit ID Number (1-7), Then
3 Total Number of Units in Chain (1-7), Then
The unit ID identifies each unit within a chain. Adding or removing EL25s will require the unit ID's to be re-entered.
Factory Setting: Unit ID 1 and Number of Units in Chain 1.
This allows you to verify a unit's number within a chain. When you perform this step, the unit will respond with the
number of beeps corresponding to its unit ID number. Two beeps, for example, mean the unit is number 2 in the chain.
Programming Multiple Units Overview
Programming Multiple Units Overview
Set the Unit ID Number and Number of Units in Chain:
2
Verify Unit Number:
111
Important: This must be performed
for
EACH unit in the Chain.
EACH unit in the Chain must have the same “Rings Before Answer”.
EACH unit in the Chain must have the same “Alternate Prefix”.
Unique Unit ID Sequencial Order
Number of Units in Chain “7”
Unit ID “1”
Residence
Unit ID “2”
Unit ID “3”
Unit ID “7”
Telco Entrance Box
Demarcation Point
Example:
16 Factory Setting - 5 Rings
115
Factory Setting - Normal
Important:

Page 10
Getting Started
EL25 SetUp “Your Settings”
Change the unit password to prevent any tampering with your system's database. When changing the password,
save a copy of it in a secure location. If you lose the password, you
will not be able to enter into programming
mode. Factory Setting: 000000 (See Page 6)
The EL25 comes preprogrammed with Factory Settings. When the unit is first installed,
you DO NOT need to program each feature.
Review the unit's factory settings before programming (see
Quick Reference Guide in front for ALL the Factory
Settings).
The Unit ID number identifies each unit within the chain. Setting the “Unit ID” and “Number of Units in the
Chain” are
required so Versa XS can send or receive data to/from the correct units within the chain.
Factory Setting: Unit ID Number “1” and Number of Units in Chain “1”. (See Previous Page)
EL25 SetUp “Your Settings”
EL25 SetUp “Your Settings”
Change the Unit Password
Set the Clock
Change the Unit's ID and Chain Number for Multiple Unit Configurations ONLY
3
1
2
24-Hour Time
Year Month Day
2 3 4
Sets the clock to 1PM, Saturday, January 1st, 2005.
Example:
1
1 Press Then
Important: We recommend you check the clock after installation.
An accurate clock is critical to the proper use of schedules, time zones and for accurately reporting transactions.
The system will adjust itself to daylight saving time if enabled.
All time must be entered using a 24-hour format (
8AM=0800, 3PM=1500 etc. )
Enter Date (yymmdd). Then (#)
2
Enter Day of week. Then (#)
3
4Time of Day (hhmm). Then (#)
1 = Sunday, 2 = Monday, 3 = Tuesday, 4 = Wednesday, 5 = Thursday, 6 = Friday, 7 = Saturday
If you make an error during an entry, press the asterisk key (*) to begin again.
1 2 3
1 Press Then
2 Change (1) or Verify (2) the Password. Then (#)
3 Enter New Password or Password to Verify (6 Digits). Then (#)
Example:
Changes the unit's password to “123456”.

Page 11
A relay is a device that reacts to an electric current to activate other devices. Allowing
the EL25 to lock or unlock a door/gate, shunt (bypass) alarm contacts, signal an alarm,
or turn on a camera wired to a closed-circuit television (CCTV). The relays can be
programmed to 5 different modes.
The EL25
must have all external access control device options configured into it, before many of
the other programming options can proceed. You must tell the unit “
what it's wired to ” and “ how
you want the devices to behave. ” To do this you must know what a “ Door ” Number is and what a
“
Relay ” is.
EL25 SetUp “Your Settings”
EL25 SetUp “Your Settings”
What is a Relay?
A Number (1-4) YOU assign to the EL25 unit to Identify the External Access Control
Devices wired to it. Up to 4 devices can be connected. Once identified, the unit will keep
the
Same Door Numbers in other programming. The Internal Keypad is ALWAYS
Assigned to Door Number 1.
What is a Door Number?
The 5Modes of Operation are:
Strike Relay:
A Strike Relay controls a door or gate by unlocking or opening it. It does not control any
other component associated with a system like Alarms, CCTV, etc.
Shunt Relay: A Shunt Relay is normally wired to an alarm and works with strike relays to shunt
(bypass) the alarm when the door is opened with a valid access code. If the door is forced open, the
system will not shunt the alarm and the alarm will be triggered.
CCTV Relay: A CCTV Relay activates the system's optional camera. The camera is wired to a closed
circuit television (CCTV). A camera can be activated when an alarm condition occurs or when a resident
enters a valid access code.
Alarm Relay: The Alarm Relay will activate another device, such as a siren, when 3 conditions occur. A
door is opened without a valid access code, A door is open past the allotted time programmed in, or too
many invalid codes are tried. Any of these will trigger the alarm relay.
Control Relay: The Control Relay can control another device such as an outdoor or indoor light near
the unit. For example, you could configure the system to turn on an entry light through a darkened area
after a resident enters a valid access code. Then the light would then turn off after a specified amount of
time.
Setup External Access Control Devices

Page 12
To perform these 4 steps you MUST know EXACTLY where the External Access Control
Device(s) were wired in “Your” EL25! When the table on page 14 is completed by you or
your installer, this will help you understand “Your” personal layout. If you do not know
this, DO NOT PROCEED. Consult your Installer and/or refer to the installation manual for
assistance.
Assign Each External Access Control Device to a Door Number: When a valid access code is entered
into a external access control device, the Assigned
door's relays will activate (See Below).
Set Each Relay Mode for the Appropriate Response: There are 5 different relay modes (Previous Page).
The relay mode determines what the relay will control (a door, alarm, CCTV, etc.). (Next Page)
Set Each Relay's Activation Time: The relay time determines the amount of time the relay remains
activated. For example, when a strike relay activates to unlock a door, the relay activation time determines
how long the door will remain unlocked. (Next Page)
Assign Each Door Number to One or More Relays: Defines which relays will activate when a resident
presents a valid access code to an external access control device. (Next Page)
Step 1
Step 2
Step 3
Step 4
1 Press
2 Enter External Access Control Device Number (1-4). Then (#)
3 Enter External Access Control Device Type (0-2). Then (#)
4 Assign a Door Number (1-4) to the Device. Then (#)
The EL25 can be equipped with Wiegand reader and radio frequency (RF) modules that allow your system to
accommodate external access control devices such as a Wiegand-compatible card reader (keypad) and RF
receiver.
In order for the devices to work successfully, you must assign them a “Door Number”. When a
valid access code is presented to the device, the
Assigned Door's Relays will activate.
Factory Setting: EL25 Keypad Always Assigned to Door 1, No Devices Assigned - 0
Then
EL25 SetUp “Your Settings”
EL25 SetUp “Your Settings”
Assign Each External Access Control Device a “Door Number”:
60
Device “1” is a Radio Receiver and Assigned as Door “3”.
Example A:
1 2 3 4
Device “3” is a Card Reader or Keypad and Assigned as Door “4”.
Example B:
1 2 3 4
0 = Not Activated/No Device Assigned
1 = (Wiegand) Card Reader or Keypad Only
2 = RF Receiver
Internal Keypad is ALWAYS Assigned to External Access Control Device Number 0
Step 1
Note: A “Door Number” is a number
you assign to each external access
control device.
Important: Allthroughepsmust be
performed for
EACH external access
control device of unit.
14
There are 3 sample configurations on page 14-16 to help you understand
the 4 step process needed to setup YOUR external access control devices.
Configuring “YOUR” EL25

Page 13
1 Press
2 Enter the Relay Number (1-4). Then (#)
3 Enter Activation Time (1-300 Seconds). Then (#)
Then
1 Press
2 Enter Door Number (1-4). Then (#)
3 Enter Relays to be Activated (0000-1111). Then (#)
Then
Example:
1 2 3
1 2 3
Assigns Relay “2” as a Shunt Relay
When Activated, the Relay Number “4” will activate for “30” seconds.
When a Resident uses a Valid Code at “Door 1”, Relay “1” and Relay “2” will Activate.
Example:
Example:
1 2 3
1 Press Then
Set Each “Relay Mode” to get the Appropriate Response:
2 Enter the Relay Number (1-4). Then (#)
This is the amount of time (in seconds) the relay remains activated. This will define the amount of time a
door cycles (unlocks, then relocks) or how long the CCTV camera remains on after being activated.
Factory Setting: All Relays are set at 10 seconds
EL25 SetUp “Your Settings”
EL25 SetUp “Your Settings”
Set Each Relay's “Activation Time”:
3 Enter Relay Mode (0-5). Then (#)
0 = Not Used
1 = Strike -
controls a door/gate by unlocking/opening it.
2 = Shunt - bypasses the alarm under normal circumstances.
3 = CCTV - activates system's optional camera.
4 = Alarm - activates another device (siren).
5 = Control - controls another device (on/off light).
65
There are 5 different relay modes. The Relay Mode determines what the response will be when a valid access
code is entered (open a door, turn on an alarm, turn on a light then turn it off, turn on a CCTV, etc.).
Factory Setting: All Relays are Set at “1 - Strike”
Step 2
Step 3
66
When a valid access code is used at an external access control device (Door), the EL25 can be set to activate
one or more relays. Factory Settings: Door 1 Activates Relay 1; Door 2 Activates Relay 2;
Door 3 Activates Relay 3; Door 4 Activates Relay 4
Assign “Each” Door Number to One or More Relays:
Step 4
61
Note: A relay that controls a gate operator must be set to activate for 2 seconds .
0 = Deactivate , 1 = Activate (1st digit=Relay 4, 2nd digit=Relay 3, etc.)
Relay 4 Relay 3 Relay 2 Relay 1
Deact Deact Activate Activate
Important: Allthroughepsmust be
performed for
EACH Door Number
assigned to the unit.
13
Important: Allthroughepsmust be
performed for
EACH Relay assigned
to the unit.
13
Important: Allthroughepsmust be
performed for
EACH Relay assigned
to the unit.
13

Page 14
Sample: EL25 Controlling 1 Door (Page 16)
EL25 SetUp “Your Settings”
EL25 SetUp “Your Settings”
When “Your Door Settings” or “ Door 1,2,3 or 4 ” are referenced throughout this guide,
this completed chart will outline how your EL25 system will function.
Location Relay Relay Mode Relay Function Relay Activation Time (Seconds)
Front Door
1 Strike Unlocks Door 10 sec.
2 Shunt Bypasses/Signals Alarm 40 sec.
Device
Main Keypad
(REX) Exit Request
Door 1 3 Alarm Sounds a Siren 10 sec.
4 CCTV Activates Camera 10 sec.
Sample: EL25 Controlling 2 Doors and a Vehicle Gate (Page 16)
Location Door No.
Door No.
Relay Relay Mode Relay Function Relay Activation Time (Seconds)
Front Door
Back Door
Gate Operator
1 Strike Unlocks Door 10 sec.
2 Control Turns on Security light 60 sec.
Device
Main Keypad and Postal Lock
Security Light
Wiegand Card Reader
Transmitter
Door 1
Door 2
Door 3
3 Strike Unlocks Door 10 sec.
4 Strike Opens Gate 10 sec.
Sample: EL25 Controlling 4 Doors (Page 17)
Location Relay Relay Mode Relay Function Relay Activation Time (Seconds)
Front Door (Entrance)
Front Door (Exit)
Back Door
Manager’s Door
1 Strike Unlocks Door 10 sec.
2 Strike Unlocks Door 10 sec.
Location Relay Relay
Mode Relay Function Relay Activation
Time (Seconds)
Device Door No.
Device
Main Keypad
Wiegand Keypad
Wiegand Card Reader
Wiegand Card Reader
Door 1
Door 2
Door 3
Door 4
3 Strike Unlocks Door 10 sec.
4 Strike Unlocks Door 10 sec.
“Your” Door Settings (See Tables below for reference)
Door No.
Sample: EL25 Controlling Single Family Residence (Page 18)
Location Door No. Relay Relay Mode Relay Function Relay Activation Time (Seconds)
Driveway
Pedestrian Gate
In EL25
1 Strike Opens Vehicular Gate 10 sec.
2 Control Turns on Security Light 10 sec.
Device
Main Keypad and
(REX) Exit Request
CCTV
Wiegand Card Reader
Door 1
Door 2
Door 3
3 Strike Unlocks Pedestrian Gate 10 sec.
4 CCTV Activates Camera 10 sec.
Sample: EL25 Controlling Multi-Resident Apartment (Page 19)
Location Relay Relay Mode Relay Function Relay Activation Time (Seconds)
Front Door (Entrance)
Vehicular Gate
Pool Gate
Front Door (Entrance)
1 Strike Unlocks Door 10 sec.
2 Strike Unlocks Door 10 sec.
Device
Main Keypad
Transmitter and REX Exit Device
Wiegand Card Reader
Siren
Door 1
Door 2
Door 3
Door 4
3 Strike Unlocks Door 10 sec.
4 Shunt Bypasses/Signals Alarm 30 sec.
Door No.

Page 15
How your system has been wired is an important part of programming it. Write down your
configuration. To help visualize it, draw a map of it below. If you're unsure of your setup, consult
your dealer/installer for more information.
EL25 SetUp “Your Settings”
Your System Layout
EL25 SetUp “Your Settings”
Relay 1
Device 0
Door Stat 1
Connection
Door Sensor
Exit Device
and/or
Door Stat 2
Connection
Door Sensor
Exit Device
and/or
Door Stat 3
Connection
Door Sensor
Exit Device
and/or
Door Stat 4
Connection
Door Sensor
Exit Device
and/or
Device 1
Device 2
Device 3
Device 4
External Access Control Device(s) connected to aux board(s)
Relay Connections
Autocall
Device
Yes
No
Postal
Lock
Yes
No
CCTV
Camera
Yes
No
Relay 2
Relay 3
Relay 4
(Default Internal Keypad)

Page 16
EL25 SetUp “Your Settings”
EL25 SetUp “Your Settings”
Relay 1 - Strike Mode
Unlocks Door for 10 sec.
Relay 2 - Control Mode
Turns on Security Light
for 60 sec.
Relay 3 - Alarm Mode
Sounds Siren for 10 sec.
Relay 2 - Shunt Mode
Bypasses/Signals Alarm
for Maglock for 40 sec.
Relay 4 - CCTV Mode
Activates Camera for
10 sec.
EL25
Main Keypad
(Front Door)
EL25
Main Keypad
(Front Door)
Card Reader (Back Door)
Transmitter
(Gate Operator)
REX Device
(Exit)
Relay 1 - Strike Mode
Unlocks Door for 10 sec.
Relay 3 - Strike Mode
Unlocks Door for 10 sec.
Relay 4 - Strike Mode
Opens Gate for 10 sec.
EL25 Controlling 1 Door
EL25 Controlling 2 Doors and Vehicle Gate
Postal
Lock
Location Relay Relay Mode Relay Function Relay Activation Time (Seconds)
Front Door
1 Strike Unlocks Door 10 sec.
2 Shunt Bypasses/Signals Alarm 40 sec.
Device
Main Keypad
(REX) Exit Request
Door 1 3 Alarm Sounds a Siren 10 sec.
4 CCTV Activates Camera 10 sec.
Door No.
Location Door No. Relay Relay Mode Relay Function Relay Activation Time (Seconds)
Front Door
Back Door
Gate Operator
1 Strike Unlocks Door 10 sec.
2 Control Turns on Security light 60 sec.
Device
Main Keypad and Postal Lock
Security Light
Wiegand Card Reader
Transmitter
Door 1
Door 2
Door 3
3 Strike Unlocks Door 10 sec.
4 Strike Opens Gate 10 sec.

Page 17
EL25 SetUp “Your Settings”
EL25 SetUp “Your Settings”
EL25
Main Keypad
(Front Door)
Wiegand Keypad (Exit)
Card Reader
(Back Door)
Card Reader
(Manager's Door)
EL25 Controlling 4 Doors
Relay 1 - Strike Mode
Unlocks Door for 10 sec.
Relay 2 - Strike Mode
Unlocks Door for 10 sec.
Relay 3 - Strike Mode
Unlocks Door for 10 sec.
Relay 4 - Strike Mode
Unlocks Door for 10 sec.
Location Relay Relay Mode Relay Function Relay Activation Time (Seconds)
Front Door (Entrance)
Front Door (Exit)
Back Door
Manager’s Door
1 Strike Unlocks Door 10 sec.
2 Strike Unlocks Door 10 sec.
Device
Main Keypad
Wiegand Keypad
Wiegand Card Reader
Wiegand Card Reader
Door 1
Door 2
Door 3
Door 4
3 Strike Unlocks Door 10 sec.
4 Strike Unlocks Door 10 sec.
Door No.
Exit Enter

Page 18
Location Door No. Relay Relay Mode Relay Function Relay Activation Time (Seconds)
Driveway
Pedestrian Gate
In EL25
1 Strike Opens Vehicular Gate 10 sec.
2 Control Turns on Security Light 10 sec.
Device
Main Keypad and
(REX) Exit Request
CCTV
Wiegand Card Reader
Door 1
Door 2
Door 3
3 Strike Unlocks Pedestrian Gate 10 sec.
4 CCTV Activates Camera 10 sec.
EL25 SetUp “Your Settings”
EL25 SetUp “Your Settings”
Single Family Residence
This EL25 can operate the vehicular gate with an access code or by remote control. It will allow
Pedestrians entry with an Access Card. It will also open the gate automatically for exiting cars.
EL25 with optional CCTV
Card Reader
(Pedestrian Gate)
Gate Operator
(Vehicular Gate)
Relay 3 - Unlocks
Pedestrian Gate
Relay 1 - Opens
Vehicular Gate
Relay 2 - Turns on Light
Car Exit Sensor
Camera is always on.

Page 19
Location Relay Relay Mode Relay Function Relay Activation Time (Seconds)
Front Door (Entrance)
Vehicular Gate
Pool Gate
Front Door (Entrance)
1 Strike Unlocks Door 10 sec.
2 Strike Unlocks Door 10 sec.
Device
Main Keypad
Transmitter and REX Exit Device
Wiegand Card Reader
Siren
Door 1
Door 2
Door 3
Door 4
3 Strike Unlocks Door 10 sec.
4 Shunt Bypasses/Signals Alarm 30 sec.
Door No.
EL25
(Main Entrance)
Card Reader
(Pool Gate)
Gate Operator
(Vehicular Gate)
Manager's
Office
Parking Lot
Internal Keypad Relay 1
Opens Main Entrance
Card Reader Relay 3
Opens Pool Gate
Car Exit Sensor
EL25 SetUp “Your Settings”
EL25 SetUp “Your Settings”
Multi-Resident Complex
This EL25 can control the property with a vehicular gate operator, access card or the unit's
keypad. Residents can use programmed transmitters for the parking lot, access cards for the pool
or a personal entry code for the main entrance. The main entrance is equipped with a door sensor
to alert management about inappropriate use. The exit sensor will automatically open the gate for
exiting cars.
Pool
RF Receiver Relay 2
Opens Vehicular Gate
Relay 4 - Shunts Alarm
for Main Entrance