Channel Vision AB-315 User manual

AB-315
®
iBus Wall-Dock for A-Bus Audio Systems
By
TM
0
1

2
Front/Top Front/Bottom
Wall Dock
Sliding Dock Platform
Slides up to conceal
the dock connector
Non-Skid Pad
Secures the iPod
Input RJ-45 & 110 Connectors
Connect to CAT5 Audio Hub
CAT5 cable (only use one)
Output RJ-45 & 110 Connectors
Connect to CAT5 Audio Amplifier Input
CAT5 cable (only use one)
Slide Up
Dock Connector
Connects to iPod
Features:
!Compatible with all A-BUS audio systems
!Charges the iPod
!Senses audio to automatically override the main audio source
!Supports IR control: compatible with A0505 or Apple Remote
!Uses CAT5 cabling
!Mounts in a standard 2-gang box
®®
The AB-315 is an on-wall iPod docking station for A-BUS audio
systems. The dock connector slides in and out to adjust for any iPod and
the non-skid pad helps to hold the music player in place. With all the
popular features of AB-313, the new AB-315 adds elegant and
contemporary styling to make it the perfect choice for anyone who wants
to enjoy their music without defacing their wall. (See Made For section on
page 3 for a list of compatible iPods.)
Hinged Dock Lid
Rotates down to
cover the dock
connector
Sliding Dock Lever
Slides the dock connector forward, providing
easy access to dock your iPod

3
Installing the Trim Plate Accessory
Install Output
wall plate in j-box
Install Trim plate chassis
over output wall plate
Snap front cover
over chassis
Snap side flange on
to front cover
Snap trim
into place
Compatibility
Made For:
!iPod touch (2nd generation)
!IPod touch (1st generation)
!iPod classic
!iPod video
!iPod nano (5th generation)
!iPod nano (4th generation)
!iPod nano (3rd generation)
!iPod nano (2nd generation)
!iPod nano (1st generation)
!iPod mini
!iPod with dock connector

4
C
HANNEL
V
ISION
TM
1 A- r Modul
4 BUS Dist ibution e
Modl e
114
P- 0
V
+24 DC
Power
12V
+DC
Ss
tatu
Sys emt
Sys em
t
Input
Lal
oc
Iu
np t
Zone 1 e
Zon 2Ze 3
on
Zone 4Es
xpan ion
p
Out ut
c
Lo al
Priority Signal
LR
Em ttersi
POR
C
HANNEL
TM
IIN
V
SO
C
HANNEL
IIN
V
SO
TM
IR
x
System Wiring Diagram
Using the AB-315 as a local source input module
AB-124
P-1014
A0501,
A0502,
or
A0505
AB-315
(Rear)
AB-315
(Front)
Speakers
The shuttle control buttons
on the A0501, A0502, &
A0505 remotes can be
used to control the iPod.
Tape Monitor or
Room 2 output
(Optional) IR emitters
Sat radio
DVD player
CD player
Receiver
Source
CHANNEL VISION
Pwr
TM
C
HAN L SIONE
V
IN
S
O
U
R
C
E
ZN
OE
ER
POW
MUTE
VOL
1
2
3
4
MO EL
D
A0501
PWER
O

5
1 - odul 4 A BUS Distribution Me
Model
14
P- 01
+24V C
D
Power
V
+12 DC
Satust
Sys emt
ys em
St
np
Iut
La
oc l
Iu
np t
Zo e 1
n
Zone 2e
Zon 3Zo e 4n Ep nsionxa
Output
c
Lo al
Poty
ri ri Si nal
g
LR
m tters
Ei
PRO
HANNE
C
L
TM
II
V
SON
HANNE
C
L
II
V
SO
N
TM
IR
x
AN
E
C
HN L
II
V
SON
TM
System Wiring Diagram
Using the AB-315 as a main source input module
P-1014
AB-124
A0501,
A0502,
or
A0505
AB-315
(Rear)
Tape Monitor or
Room 2 output
(Optional) IR emitters
Sat radio
DVD player
CD player
Receiver
Source
CHANNEL VISION
Pwr
Source
CHANNEL VISION
Pwr
Source
CHANNEL VISION
Pwr
Source
CHANNEL VISION
Pwr
TM
C
AN O
HNEL
V
ISI N
S
O
U
R
C
E
ZNOE
POWER
T
MU E
VOL
1
2
3
4
O
MDEL
0
A501
WER
PO
In this configuration, an iPod docked in the
AB-315 will override the other audio source
whenever the iPod is playing (note the
position of the priority switch on the P-1014).
The iPod can be controlled by pointing an
A0501 or A0502 remote control at any of the
amplified keypads.

6
Installing the Wall Dock
Installation Steps
1. Connect all wiring.
2. Attach main chassis to j-box using
the provided four 6-32 screws.
3. Feed the dock connector circuit
board through the opening in the
front cover.
4. Hang the front cover on the main
chassis from the two top tabs.
5. Secure the front cover with the
two small screws at the bottom.
6. Place the dock platform over
the slide rail and push
downward until the retention
snaps are engaged.
7. Slide the side protectors
into the slots on the main
chassis.
Retention
Snap
Slide Rail
2
2
4
3
3
5
6
6
7
5
2
1
Completed Installation
Steps 3 & 4 complete
Steps 5 & 6 complete

Installing the Wall Dock
(3-gang Installation)
In some installations it may be desirable to mount a single gang control
keypad next to the AB-315. To accomplish this, the single gang trim plate
can be installed next to the AB-315 in a 3-gang junction box.
Follow the steps below:
4
3
Completed Installation
7
Installation Steps
1. Connect all wiring. Use the correct
installation tools: J-110 tool, or
1014 crimp tool.
2. Install keypad and single-gang
trim plate in the far left position
of the 3-gang junction box.
(See details on page 3)
3. Leave off the right side
flange and trim piece.
4. Install the iPod dock in the
left side of the 3-gang j-box.
It will overlap and snap into
the single gang trim plate.
(See page 5 for details)
See attachment
detail on previous page

Docking the iPod
The dock platform can slide up to hide
the dock connector when the system is
not in use. Make sure the dock platform
is in the down position so the dock
connector is exposed (as shown here).
The sliding dock lever beneath the dock adjusts the position of the
dock connector to create a perfect fit for all compatible iPods (see
page 3 for a list of compatible iPods).
8

CHANNEL VISION
S
O
U
R
C
E
ZONE
POWER
MUTE
4
3
2
1
CAMERA
CATV
MOD
VOL
1
2
3
4
MODEL
A0505
POWER
We realize that custom integrators way wish to design advanced control systems. To
provide assistance we have published the hex codes for the IR commands (see below).
(IR codes can be downloaded at: www.channelvision.com)
Hex codes for IR commands:
iBus Play/Pause:
0000 006D 0000 000B 001F 001F 001F 001F 003F 003F 001F 001F 001F 001F 001F 001F
003F 001F 001F 001F 001F 003F 003F 003F 001F 0CA2
iBus Skip <<:
0000 006D 0000 000B 001F 001F 003F 001F 001F 003F 001F 001F 001F 001F 001F 001F
003F 001F 001F 003F 001F 001F 003F 003F 001F 0CA2
iBus Skip >>:
0000 006D 0000 000A 001F 001F 001F 001F 003F 003F 001F 001F 001F 001F 001F 001F
003F 003F 003F 001F 001F 003F 003F 0CC3
Using the A0505 Remote Control
The buttons above the iBus
label on the A0505 remote
control will mimic the
functions on the iPod wheel.
The volume, mute, power, and source buttons
on the A0505 are designed to control Channel
Vision’s whole-house audio systems such as
the A4603 and P-1044.
Please note that this remote will only function
when your iPod is docked in the AB-315 wall
dock. It must be pointed at an IR receiver that
is part of an amplified keypad that is wired
“downstream”.
9

Stripping and Connecting CAT5 Wire
Blade
Cat5
1. Place the CAT5 between the blade and the first notch of the J-110 tool.
CAT5 cable should be stripped with a proper stripping tool, such as Channel
Vision’s J-110 tool.
Slight
pressure
Rotate
1 turn only
2. Rotate the tool only once. Multiple
turns will cause you to cut into the
inner wires.
3. Inspect the inner wires for damage.
If any wires are cut start over at step 1.
Check for damage
Green/White
Green
Orange/White
Blue
Blue/White
Orange
Brown/White
Brown
TIA-568A RJ-45 Modular Plug
Side view:
Top view:
10