Channel Vision AB-315 User manual

AB-315
®
iBus Wall-Dock for A-Bus Audio Systems
By
TM
0
1

2 3
Installing the Trim Plate Accessory
Front/Top Front/Bottom
Wall Dock
Sliding Dock Platform
Slides up to conceal
the dock connector
Non-Skid Pad
Secures the iPod
Input RJ-45 & 110 Connectors
Connect to CAT5 Audio Hub
CAT5 cable (only use one)
Output RJ-45 & 110 Connectors
Connect to CAT5 Audio Amplifier Input
CAT5 cable (only use one)
Slide Up
Dock Connector
Connects to iPod
Install Output
wall plate in j-box
Install Trim plate chassis
over output wall plate
Snap front cover
over chassis
Snap side flange on
to front cover
Snap trim
into place
Features:
!
!Charges the iPod
!Senses audio to automatically override the main audio source
!Supports IR control: compatible with A0505 or Apple Remote
!Uses CAT5 cabling
!Mounts in a standard 2-gang box
Compatible with all A-BUS audio systems
®
The AB-315 for A-BUS a
systems. The dock connector slides in and out to adjust for any iPod and
the non-skid pad helps to hold the music player in place. With all the
popular features of AB-313, the new AB-315 adds elegant and
contemporary styling to make it the perfect choice for anyone who wants
to enjoy their music without defacing their wall. (See Made For section on
page 3 for a list of compatible iPods.)
®
is an on-wall iPod docking station udio
Hinged Dock Lid
Rotates down to
cover the dock
connector
Sliding Dock Lever
Slides the dock connector forward, providing
easy access to dock your iPod
Compatibility
Made For:
!iPod touch (2nd generation)
!IPod touch (1st generation)
!iPod classic
!iPod video
!iPod nano (5th generation)
!
!iPod nano (3rd generation)
!iPod nano (2nd generation)
!iPod nano (1st generation)
!iPod mini
!iPod with dock connector
iPod nano (4th generation)

2 3
Installing the Trim Plate Accessory
Front/Top Front/Bottom
Wall Dock
Sliding Dock Platform
Slides up to conceal
the dock connector
Non-Skid Pad
Secures the iPod
Input RJ-45 & 110 Connectors
Connect to CAT5 Audio Hub
CAT5 cable (only use one)
Output RJ-45 & 110 Connectors
Connect to CAT5 Audio Amplifier Input
CAT5 cable (only use one)
Slide Up
Dock Connector
Connects to iPod
Install Output
wall plate in j-box
Install Trim plate chassis
over output wall plate
Snap front cover
over chassis
Snap side flange on
to front cover
Snap trim
into place
Features:
!
!Charges the iPod
!Senses audio to automatically override the main audio source
!Supports IR control: compatible with A0505 or Apple Remote
!Uses CAT5 cabling
!Mounts in a standard 2-gang box
Compatible with all A-BUS audio systems
®
The AB-315 for A-BUS a
systems. The dock connector slides in and out to adjust for any iPod and
the non-skid pad helps to hold the music player in place. With all the
popular features of AB-313, the new AB-315 adds elegant and
contemporary styling to make it the perfect choice for anyone who wants
to enjoy their music without defacing their wall. (See Made For section on
page 3 for a list of compatible iPods.)
®
is an on-wall iPod docking station udio
Hinged Dock Lid
Rotates down to
cover the dock
connector
Sliding Dock Lever
Slides the dock connector forward, providing
easy access to dock your iPod
Compatibility
Made For:
!iPod touch (2nd generation)
!IPod touch (1st generation)
!iPod classic
!iPod video
!iPod nano (5th generation)
!
!iPod nano (3rd generation)
!iPod nano (2nd generation)
!iPod nano (1st generation)
!iPod mini
!iPod with dock connector
iPod nano (4th generation)

45
1 4 A-BUS Distribution Module
Model
P-1014
+24VDC
Power
+12VDC
Status
System
System
Input
Local
Input
Zone 1 Zone 2 Zone 3 Zone 4 Expansion
Output
Local
Priority Signal
LREmitters
PRO
CHANNEL
TM
VISION
IR
x
1 4 A-BUS Distribution Module
Model
P-1014
+24VDC
Power
+12VDC
Status
System
System
Input
Local
Input
Zone 1 Zone 2 Zone 3 Zone 4 Expansion
Output
Local
Priority Signal
LREmitters
PRO
CHANNEL
TM
VISION
IR
x
System Wiring Diagram
Using the AB-315 as a local source input module
System Wiring Diagram
Using the AB-315 as a main source input module
AB-124
P-1014
P-1014
AB-124
A0501,
A0502,
or
A0505 A0501,
A0502,
or
A0505
AB-315
(Rear)
AB-315
(Rear)
AB-315
(Front)
Speakers
The shuttle control buttons
on the A0501, A0502, &
A0505 remotes can be
used to control the iPod.
Tape Monitor or
Room 2 output
Tape Monitor or
Room 2 output
(Optional) IR emitters
(Optional) IR emitters
Sat radio
Sat radio
DVD player
DVD player
CD player
CD player
Receiver
Receiver
Source
CHANN EL VI SIO N
Pwr
TM
CHANNEL VISION
S
O
U
R
C
E
ZONE
POWER
MUTE
VOL
1
2
3
4
MODEL
A0501
POWER
Source
CHAN NE L VI SI ON
Pwr
Source
CHAN NE L VI SI ON
Pwr
Source
CHAN NE L VI SI ON
Pwr
Source
CHAN NE L VI SI ON
Pwr
TM
CHANNEL VISIO N
S
O
U
R
C
E
ZONE
POWER
MUTE
VOL
1
2
3
4
MODEL
A0501
POWER
In this configuration, an iPod docked in the
AB-315 will override the other audio source
whenever the iPod is playing (note the
position of the priority switch on the P-1014).
The iPod can be controlled by pointing an
A0501 or A0502 remote control at any of the
amplified keypads.

45
1 4 A-BUS Distribution Module
Model
P-1014
+24VDC
Power
+12VDC
Status
System
System
Input
Local
Input
Zone 1 Zone 2 Zone 3 Zone 4 Expansion
Output
Local
Priority Signal
LREmitters
PRO
CHANNEL
TM
VISION
IR
x
1 4 A-BUS Distribution Module
Model
P-1014
+24VDC
Power
+12VDC
Status
System
System
Input
Local
Input
Zone 1 Zone 2 Zone 3 Zone 4 Expansion
Output
Local
Priority Signal
LREmitters
PRO
CHANNEL
TM
VISION
IR
x
System Wiring Diagram
Using the AB-315 as a local source input module
System Wiring Diagram
Using the AB-315 as a main source input module
AB-124
P-1014
P-1014
AB-124
A0501,
A0502,
or
A0505 A0501,
A0502,
or
A0505
AB-315
(Rear)
AB-315
(Rear)
AB-315
(Front)
Speakers
The shuttle control buttons
on the A0501, A0502, &
A0505 remotes can be
used to control the iPod.
Tape Monitor or
Room 2 output
Tape Monitor or
Room 2 output
(Optional) IR emitters
(Optional) IR emitters
Sat radio
Sat radio
DVD player
DVD player
CD player
CD player
Receiver
Receiver
Source
CHANNEL VIS I ON
Pwr
TM
CHANNEL VISION
S
O
U
R
C
E
ZONE
POWER
MUTE
VOL
1
2
3
4
MODEL
A0501
POWER
Source
CHAN NE L VI SI ON
Pwr
Source
CHAN NE L VI SI ON
Pwr
Source
CHAN NE L VI SI ON
Pwr
Source
CHAN NE L VI SI ON
Pwr
TM
CHANNEL VISIO N
S
O
U
R
C
E
ZONE
POWER
MUTE
VOL
1
2
3
4
MODEL
A0501
POWER
In this configuration, an iPod docked in the
AB-315 will override the other audio source
whenever the iPod is playing (note the
position of the priority switch on the P-1014).
The iPod can be controlled by pointing an
A0501 or A0502 remote control at any of the
amplified keypads.

Installing the Wall Dock
(3-gang Installation)
6
Installing the Wall Dock
Installation Steps
1. Connect all wiring.
2. Attach main chassis to j-box using
the provided four 6-32 screws.
3. Feed the dock connector circuit
board through the opening in the
front cover.
4. Hang the front cover on the main
chassis from the two top tabs.
5. Secure the front cover with the
two small screws at the bottom.
6. Place the dock platform over
the slide rail and push
downward until the retention
snaps are engaged.
7. Slide the side protectors
into the slots on the main
chassis.
Retention
Snap
Slide Rail
2
2
4
3
3
5
6
6
7
5
2
1
In some installations it may be desirable to mount a single gang control
keypad next to the AB-315. To accomplish this, the single gang trim plate
can be installed next to the AB-315 in a 3-gang junction box.
Follow the steps below:
4
3
Completed Installation
7
Completed Installation
Steps 3 & 4 complete
Steps 5 & 6 complete
Installation Steps
1. Connect all wiring. Use the correct
installation tools: J-110 tool, or
1014 crimp tool.
2. Install keypad and single-gang
trim plate in the far left position
of the 3-gang junction box.
(See details on page 3)
3. Leave off the right side
flange and trim piece.
4. Install the iPod dock in the
left side of the 3-gang j-box.
It will overlap and snap into
the single gang trim plate.
(See page 5 for details)
See attachment
detail on previous page

Installing the Wall Dock
(3-gang Installation)
6
Installing the Wall Dock
Installation Steps
1. Connect all wiring.
2. Attach main chassis to j-box using
the provided four 6-32 screws.
3. Feed the dock connector circuit
board through the opening in the
front cover.
4. Hang the front cover on the main
chassis from the two top tabs.
5. Secure the front cover with the
two small screws at the bottom.
6. Place the dock platform over
the slide rail and push
downward until the retention
snaps are engaged.
7. Slide the side protectors
into the slots on the main
chassis.
Retention
Snap
Slide Rail
2
2
4
3
3
5
6
6
7
5
2
1
In some installations it may be desirable to mount a single gang control
keypad next to the AB-315. To accomplish this, the single gang trim plate
can be installed next to the AB-315 in a 3-gang junction box.
Follow the steps below:
4
3
Completed Installation
7
Completed Installation
Steps 3 & 4 complete
Steps 5 & 6 complete
Installation Steps
1. Connect all wiring. Use the correct
installation tools: J-110 tool, or
1014 crimp tool.
2. Install keypad and single-gang
trim plate in the far left position
of the 3-gang junction box.
(See details on page 3)
3. Leave off the right side
flange and trim piece.
4. Install the iPod dock in the
left side of the 3-gang j-box.
It will overlap and snap into
the single gang trim plate.
(See page 5 for details)
See attachment
detail on previous page

CHA N N EL VISIO N
S
O
U
R
C
E
ZONE
POWER
MUTE
4
3
2
1
CAMERA
CATV
MOD
VOL
1
2
3
4
MODEL
A0505
POWER
We realize that custom integrators way wish to design advanced control systems. To
provide assistance we have published the hex codes for the IR commands (see below).
(IR codes can be downloaded at: www.channelvision.com)
Hex codes for IR commands:
iBus Play/Pause:
0000 006D 0000 000B 001F 001F 001F 001F 003F 003F 001F 001F 001F 001F 001F 001F
003F 001F 001F 001F 001F 003F 003F 003F 001F 0CA2
iBus Skip <<:
0000 006D 0000 000B 001F 001F 003F 001F 001F 003F 001F 001F 001F 001F 001F 001F
003F 001F 001F 003F 001F 001F 003F 003F 001F 0CA2
iBus Skip >>:
0000 006D 0000 000A 001F 001F 001F 001F 003F 003F 001F 001F 001F 001F 001F 001F
003F 003F 003F 001F 001F 003F 003F 0CC3
Using the A0505 Remote Control
The buttons above the iBus
label on the A0505 remote
control will mimic the
functions on the iPod wheel.
The volume, mute, power, and source buttons
on the A0505 are designed to control Channel
Vision’s whole-house audio systems such as
the A4603 and P-1044.
Please note that this remote will only function
when your iPod is docked in the AB-315 wall
dock. It must be pointed at an IR receiver that
is part of an amplified keypad that is wired
“downstream”.
Docking the iPod
The dock platform can slide up to hide
the dock connector when the system is
not in use. Make sure the dock platform
is in the down position so the dock
connector is exposed (as shown here).
The sliding dock lever beneath the dock adjusts the position of the
dock connector to create a perfect fit for all compatible iPods (see
page 3 for a list of compatible iPods).
8 9

CHA N N EL VISIO N
S
O
U
R
C
E
ZONE
POWER
MUTE
4
3
2
1
CAMERA
CATV
MOD
VOL
1
2
3
4
MODEL
A0505
POWER
We realize that custom integrators way wish to design advanced control systems. To
provide assistance we have published the hex codes for the IR commands (see below).
(IR codes can be downloaded at: www.channelvision.com)
Hex codes for IR commands:
iBus Play/Pause:
0000 006D 0000 000B 001F 001F 001F 001F 003F 003F 001F 001F 001F 001F 001F 001F
003F 001F 001F 001F 001F 003F 003F 003F 001F 0CA2
iBus Skip <<:
0000 006D 0000 000B 001F 001F 003F 001F 001F 003F 001F 001F 001F 001F 001F 001F
003F 001F 001F 003F 001F 001F 003F 003F 001F 0CA2
iBus Skip >>:
0000 006D 0000 000A 001F 001F 001F 001F 003F 003F 001F 001F 001F 001F 001F 001F
003F 003F 003F 001F 001F 003F 003F 0CC3
Using the A0505 Remote Control
The buttons above the iBus
label on the A0505 remote
control will mimic the
functions on the iPod wheel.
The volume, mute, power, and source buttons
on the A0505 are designed to control Channel
Vision’s whole-house audio systems such as
the A4603 and P-1044.
Please note that this remote will only function
when your iPod is docked in the AB-315 wall
dock. It must be pointed at an IR receiver that
is part of an amplified keypad that is wired
“downstream”.
Docking the iPod
The dock platform can slide up to hide
the dock connector when the system is
not in use. Make sure the dock platform
is in the down position so the dock
connector is exposed (as shown here).
The sliding dock lever beneath the dock adjusts the position of the
dock connector to create a perfect fit for all compatible iPods (see
page 3 for a list of compatible iPods).
8 9

10
Connection Tips and Troubleshooting
11
1) Be sure you have connected the CAT5 cable correctly. Follow the
TIA-568A standard at both ends. Incorrect wiring can cause distorted
sound or prevent the system from working at all!
2) Be sure you have connected the speakers in phase. Follow the label
on the product. Out of phase speakers can rob the system of its
bass. Especially when driving dual-voice-coil speakers.
3) Trouble with IR control?
a. Make sure you are using the correct remote control. The AB-315 will
only respond to IR signals from the Apple Remote produced by Apple
Computer or the A0505 produced by Channel Vision. Other 3rd party
remote controls are not supported.
b. Check the batteries in the remote control and change them if
necessary.
4) The AB-315 is designed to charge the iPod (see compatibility notes
on page3). When the iPod is not playing music, the screen should
indicate that the iPod is being charged. If this does not occur, make
sure the power is reaching the volume control keypad (press the
volume buttons to see if the LED indicators light up).
5) Observe wiring distance specifications. The maximum
recommended wire length between the wall dock and CAT5 audio
hub is 250 feet. Although the AB-315 may work at greater distances,
extreme distances are not recommended because erratic
performance may result due to the power loss caused by the CAT5
wire.
6) If you are experiencing problems with your iPod that occur even
when it is not docked in the AB-315, then please contact Apple
customer service for support.
7) If you need additional help troubleshooting the AB-315 please
contact Channel Vision technical support or check our website for
more details: www.channelvision.com.
System Specifications: (typical @25º C)
Operating Voltage : 24±.5VDC
Cable requirements: CAT-5 or better
Max CAT5 length: 250ft
Speaker impedance: 6-8 ohm
IR repeating: 30-60kHz
IR sensor range (AB-124): 40’@40kHz 25’@56kHz
Operating Temperature: -10ºC to +50ºC
Specifications subject to change without notice.
Stripping and Connecting CAT5 Wire
Blade
CAT5
1. Place the CAT5 between the blade and the first notch of the J-110 tool.
CAT5 cable should be stripped with a proper stripping tool, such as Channel
Vision’s J-110 tool.
Slight
pressure
Rotate
1 turn only
2. Rotate the tool only once. Multiple
turns could damage the inner wires.
3. Inspect the inner wires for damage.
If any wires are cut start over at step 1.
Check for damage
Green/White - Left channel ground
Green - Left channel
Orange/White - Right channel ground
Blue - Signal
Blue/White - Status
Orange - Right channel
Brown/White - Ground
Brown - 24vDC
TIA-568A RJ-45 Modular Plug
Side view:
Top view:

10
Connection Tips and Troubleshooting
11
1) Be sure you have connected the CAT5 cable correctly. Follow the
TIA-568A standard at both ends. Incorrect wiring can cause distorted
sound or prevent the system from working at all!
2) Be sure you have connected the speakers in phase. Follow the label
on the product. Out of phase speakers can rob the system of its
bass. Especially when driving dual-voice-coil speakers.
3) Trouble with IR control?
a. Make sure you are using the correct remote control. The AB-315 will
only respond to IR signals from the Apple Remote produced by Apple
Computer or the A0505 produced by Channel Vision. Other 3rd party
remote controls are not supported.
b. Check the batteries in the remote control and change them if
necessary.
4) The AB-315 is designed to charge the iPod (see compatibility notes
on page3). When the iPod is not playing music, the screen should
indicate that the iPod is being charged. If this does not occur, make
sure the power is reaching the volume control keypad (press the
volume buttons to see if the LED indicators light up).
5) Observe wiring distance specifications. The maximum
recommended wire length between the wall dock and CAT5 audio
hub is 250 feet. Although the AB-315 may work at greater distances,
extreme distances are not recommended because erratic
performance may result due to the power loss caused by the CAT5
wire.
6) If you are experiencing problems with your iPod that occur even
when it is not docked in the AB-315, then please contact Apple
customer service for support.
7) If you need additional help troubleshooting the AB-315 please
contact Channel Vision technical support or check our website for
more details: www.channelvision.com.
System Specifications: (typical @25º C)
Operating Voltage : 24±.5VDC
Cable requirements: CAT-5 or better
Max CAT5 length: 250ft
Speaker impedance: 6-8 ohm
IR repeating: 30-60kHz
IR sensor range (AB-124): 40’@40kHz 25’@56kHz
Operating Temperature: -10ºC to +50ºC
Specifications subject to change without notice.
Stripping and Connecting CAT5 Wire
Blade
CAT5
1. Place the CAT5 between the blade and the first notch of the J-110 tool.
CAT5 cable should be stripped with a proper stripping tool, such as Channel
Vision’s J-110 tool.
Slight
pressure
Rotate
1 turn only
2. Rotate the tool only once. Multiple
turns could damage the inner wires.
3. Inspect the inner wires for damage.
If any wires are cut start over at step 1.
Check for damage
Green/White - Left channel ground
Green - Left channel
Orange/White - Right channel ground
Blue - Signal
Blue/White - Status
Orange - Right channel
Brown/White - Ground
Brown - 24vDC
TIA-568A RJ-45 Modular Plug
Side view:
Top view:

Channel Vision Technology will repair or replace any defect in material or workmanship
which occurs during normal use of this product with new or rebuilt parts, free of charge in
the USA, for two years from the date of original purchase. This is a no hassle warranty with
no mail in warranty card needed. This warranty does not cover damages in shipment,
failures caused by other products not supplied by Channel Vision Technology, or failures
due to accident, misuse, abuse, or alteration of the equipment. This warranty is extended
only to the original purchaser, and a purchase receipt, invoice, or other proof of original
purchase date will be required before warranty repairs are provided.
Mail in service can be obtained during the warranty period by calling [phone]. A
Return Authorization number must be obtained in advance and can be marked on the
outside of the shipping carton.
This warranty gives you specific legal rights and you may have other rights (which vary
from state to state). If a problem with this product develops during or after the warranty
period, please contact Channel Vision Technology, your dealer or any factory-authorized
service center.
Channel Vision products are not intended for use in medical, lifesaving, life sustaining or
critical environment applications. Channel Vision customers using or selling Channel
Vision products for use in such applications do so at their own risk and agree to fully
indemnify Channel Vision for any damages resulting from such improper use or sale.
500-258 revB
This device complies with part 15 of the FCC rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) This device
must accept any interference received, including interference that may cause undesired
operation.
Tested To Comply
With FCC Standards Model: AB-315 iPod Wall Dock for Distributed Audio
ww w . c ha nn e lv is i o n .c o m
234 Fischer Avenue, Costa Mesa, California 92626 USA
[phone] [phone] [phone] fax
email: [email protected]
iPod is a trademark of Apple, Inc., registered in the U.S. and other countries.
Specifications: (typical @25º C)
Operating Voltage : 24VDC
Cable Requirements: CAT-5 or better
Recommended Max. Cable Length: 250ft.
Operating Temperature: -10ºC to +50ºC
Specifications subject to change without notice.
1