Chattanooga Huber 360 User manual

HUBER install : critical steps
•Make sure you have the requested tools ( see install guide)
•Follow the install guideline steps
•Unpacking ( slide 2): make sure you save all the protection elements and
boxes to be able to repack at the end of the show.
•Moving the column ( slide 5) : The sensors in the handles are sensitive
and the column should not be lift by the handles
•Moving the platform ( slides 8-9) : the plate is heavy and to move it 3
peoples at least, well positioned around are requested.
•Placing the column over the platform( slide 10) : risk of bend or twist the
bolt if not made carefully
•Connecting wires ( slide 11): only 3 socket , it’s easy, no tool requested
but should me made appropriately
•Set up ( slide 15-17 ) : platform alignment ( horizontality) and software
initialization are the most critical . I would recommend to wait after me for
this step.
HUBER 360 install 1

BOX OPENING
IMPORTANT Check the fitting to ensure proper repacking at the end of the show
You will find 3 boxes inside.
2HUBER 360 install

Check the nuts and accessory bags in one of the small box
3HUBER 360 install

Remove Wood foam and plastic film protections
Make sure you save them for the repacking
4HUBER 360 install

Unlock the straps at the column foot :
Important keep the straps for the
repacking
Move the Column : at the best with 3 peoples
Using the transport bar
VERY IMPORTANT Do not lift by the column handles
For the repacking
Place the column
foot plate in this
dedicated space
Place the column aside on the floor ( with
protection under)You can use the box top 5HUBER 360 install

Remove the Wood legs
Cut the straps that are attached to the wood base
IMPORTANT: for repacking new straps ( I will provided it ) shall be placed to lock
the platform on the base
6HUBER 360 install

Remove the Black sides covers ( not sure they will be placed over here )
On both side remove the white plastic
elements In order to acess the metal structure
to move the platform on the floor
those parts will be replaced at the end of the
install.
7HUBER 360 install

4 handles may be provided to help the lift
If so they have to be fixed on the 4 corners
They should be removed when the platform has been placed on the floor
Important : Do not place your hands on this
plastic flexible place for the lift
In case you can’t find those 4 handles in the
kit, you will have to lift the platform by placing
your hands on the the metal structure
8HUBER 360 install

Fo the lift: 3 peoples are required ( on a triangle)
One on each side and one on the top side ( the heavy component)
9HUBER 360 install

Place the column on the platform
Check the insert
IMPORTANT : this be careful to place it very
vertically at the right place over the 4 bolts
without force. . Because of the weigth and tork,
the bolts could be twist, if the column is, not
well positionned
IMPORTANT :
make sure the 3
electric wires
leaving the
column are free
and well
positioned to
be connected to
the platform
This step the MOST CRITICAL step of the install 10HUBER 360 install

Electronic Connections
They are 3 wires to connect
-The grey one with white socket
-2 whites with green socket
Important: check
the wires and
socket name to
connect
accordingly
11HUBER 360 install

Place and fix the 2 pieces of white wood floor on the top of the platform using the
screws
12HUBER 360 install

Place and fix the white plasctic covers on both side.
Important : Position with fingers all screws
before tighten with the tool .
13HUBER 360 install

Install all the white plastic covers elements
14HUBER 360 install

VERY IMPORTANT : DO NOT STAND ON THE
PLATFORM DURING THIS STEP OF THE PROCESS
Connect to the main Make sure the STOP button on
the column is on the correct
position
on « ON » position
I would recomend you wait after me for the following steps
15HUBER 360 install

INITIALISATION
VERY IMPORTANT : DO NOT STAND ON THE
PLATFORM DURING THIS STEP OF THE PROCESS
When the device is on, it starts with an initialisation
screen
Press on « Initialiser »
At this stage the platform will move for a few secondes
Make sure no one is standing or touching the platform
during this step. 16HUBER 360 install

Platform position setting : This step is critical
Check the position of the air bubble on the center of the platform.
It’s indicate the horizontality of the plate .
The goal is to position the bubble right in the center by adjusting the height of the feets
It may take some time to do it 
IMPORTANT: make sure nuts
are locked at the end of the
process
17HUBER 360 install