Chauvet Colorado 2 Zoom Tour User manual

Chauvet, 3000 N 29th Ct, Hollywood, FL 33020 U.S.A.
[phone] –[phone]
FAX [phone]
www.chauvetlighting.com
COLORado™2
USER MANUAL
Snapshot
OK on Dimmer
Outdoor OK
Sound Activated
DMX512
Master/Slave
Autoswitching
Transformer
Replaceable Fuse
User Serviceable
Duty Cycle

COLORado™ 2 User Manual 2 2/18/2009 12:45 PM
TABLE OF CONTENTS
1. Before You Begin................................................................................................................................3
What is included .......................................................................................................................................3
Unpacking Instructions..............................................................................................................................3
AC Power.................................................................................................................................................3
Safety Instructions ....................................................................................................................................4
LED Expected Lifespan.............................................................................................................................4
2. Introduction.........................................................................................................................................5
Features...................................................................................................................................................5
DMX Channel Summary............................................................................................................................6
Product Overview......................................................................................................................................8
Dimensions...............................................................................................................................................9
3. SETUP............................................................................................................................................... 10
AC Power............................................................................................................................................... 10
Mounting ................................................................................................................................................ 11
Orientation.............................................................................................................................................. 11
Rigging...................................................................................................................................................11
Lens Assembly Installation/Replacement................................................................................................. 12
Fixture Linking........................................................................................................................................ 13
Data Cabling........................................................................................................................................... 13
DMX Data Cable.....................................................................................................................................13
Cable Connectors...................................................................................................................................13
3-Pin to 5-Pin Conversion Chart ..............................................................................................................14
Setting up a DMX Serial Data Link........................................................................................................... 14
Master/Slave Fixture Linking ...................................................................................................................14
4. Operating Instructions...................................................................................................................... 15
Control Options.......................................................................................................................................15
COLORado ™ Control Quick Setup.........................................................................................................15
DMX-512 control without “ID” address .....................................................................................................15
DMX-512 addressing with ID address...................................................................................................... 16
Setting the DMX address......................................................................................................................... 17
Control Panel Functions.......................................................................................................................... 17
Menu Map .............................................................................................................................................. 18
DMX512 Channel Values........................................................................................................................ 19
STAG..................................................................................................................................................... 19
Important Notes about STAG DMX Operation.......................................................................................... 21
6. Appendix........................................................................................................................................... 24
DMX Primer............................................................................................................................................24
General Maintenance.............................................................................................................................. 25
Returns Procedure.................................................................................................................................. 25
Claims.................................................................................................................................................... 25
Photometrics...........................................................................................................................................26
COLORado ™ 2 Service Maintenance Guide........................................................................................... 27
Contact Us..............................................................................................................................................28
Blow-out Diagram. .................................................................................................................................. 29
Technical Specifications..........................................................................................................................30

COLORado™ 2 User Manual 3 2/18/2009 12:45 PM
1. BEFORE YOU BEGIN
What is included
1 x COLORado™2
1 x Power cable with plug
1 x IP66 power extension cable
1 x IP66 signal extension cable
1 x DMX input cable
1 x DMX output cable
1 x Warranty Card
1 x User Manual
Unpacking Instructions
Immediately upon receiving a fixture, carefully unpack the carton, check the contents to ensure that
all parts are present, and have been received in good condition. Notify the shipper immediately and
retain packing material for inspection if any parts appear damaged from shipping or the carton itself
shows signs of mishandling. Save the carton and all packing materials. In the event that a fixture
must be returned to the factory, it is important that the fixture be returned in the original factory box
and packing.
AC Power
This fixture has an auto-switching power supply that can accommodate a wide range of input
voltages. The only thing necessary to do before powering on the unit is to make sure the line voltage
you are applying is within the range of accepted voltages. This fixture will accommodate between
100V and 240V AC 50-60 Hz. All fixtures must be powered directly off a switched circuit and cannot
be run off a rheostat (variable resistor) or dimmer circuit, even if the rheostat or dimmer channel is
used solely for a 0% to 100% switch.

COLORado™ 2 User Manual 4 2/18/2009 12:45 PM
Safety Instructions
Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that
they also receive this instruction booklet.
Always make sure that you are connecting to the proper voltage, and that the line voltage you are
connecting to is not higher than that stated on the decal or rear panel of the fixture.
This product is intended for indoor use only! (If applicable)
To prevent risk of fire or shock, do not expose fixture to rain or moisture. Make sure there are no
flammable materials close to the unit while operating.
The unit must be installed in a location with adequate ventilation, at least 20in (50cm) from adjacent
surfaces. Be sure that no ventilation slots are blocked.
Always disconnect from power source before servicing or replacing lamp or fuse and be sure to
replace with same lamp source.
Secure fixture to fastening device using a safety chain. Never carry the fixture solely by its head. Use
its carrying handles.
Maximum ambient temperature (Ta) is 104°F (40°C). Do not operate fixture at temperatures higher
than this.
In the event of a serious operating problem, stop using the unit immediately. Never try to repair the
unit by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please
contact the nearest authorized technical assistance center. Always use the same type spare parts.
Never connect the device to a dimmer pack.
Make sure the power cord is never crimped or damaged.
Never disconnect the power cord by pulling or tugging on the cord.
Avoid direct eye exposure to the light source while it is on.
Do not daisy chain power to more than 10 units @ 120V and 20 units @ 230V.
Caution! There are no user serviceable parts inside the unit. Do not open the housing or
attempt any repairs yourself. In the unlikely event your unit may require service,
please contact CHAUVET at: 954-929-1115.
LED Expected Lifespan
LEDs gradually decline in brightness over time. HEAT is the dominant factor that leads to the
acceleration of this decline. Packaged in clusters, LEDs exhibit higher operating temperatures than in
ideal or singular optimum conditions. For this reason when all color LEDs are used at their fullest
intensity, life of the LEDs is significantly reduced. It is estimated that a viable lifespan of 40,000 to
50,000 hours will be achieved under normal operational conditions. If improving on this lifespan
expectancy is of a higher priority, place care in providing for lower operational temperatures. This
may include climatic-environmental and the reduction of overall projection intensity.
Please read these instructions carefully, which includes important
information about the installation, usage and maintenance of this
product.

COLORado™ 2 User Manual 5 2/18/2009 12:45 PM
2. INTRODUCTION
Features
3, 4, 5, or 9-channel DMX-512 LED wash light (with ID addressing)
Operating modes
3-channel: RGB control
3-channel: HSV control (hue, saturation and value)
4-channel: RGBW control
4-channel: RGB, dimmer
5-channel: RGBW, dimmer
6-channel: RGBW, dimmer, strobe
11-channel: RGBW, ID, dimmer, strobe, macro, auto, auto speed, custom, dimmer speed
RGBW color mixing with or without DMX controller
Color temperature presets (3,200ºK - 10,000ºK)
Built-in automated programs via DMX
Recall custom programs via DMX
Additional Features
High-power, 2W –3W (750mA –1000mA) LEDs
Ingress Protection: IP66
Adjustable barn doors to direct output (includes gel frame)
LED display with lock-out feature
Power and Data extension cables (3.3 FT., 1 M)
OPTIONS
COLORado Controller (COLOR-CON)
Optical systems: 15 (installed), 30 (CL20X30)

COLORado™ 2 User Manual 6 2/18/2009 12:45 PM
DMX Channel Summary
The COLORado™ 2 has a total of 7 DMX channel configurations, referred to as “Personalities” in this manual and in the
fixture onboard control board. The 7 personalities are [STAG, Arc.1, Ar1.D, Arc.2, Ar2.d, Ar2.s, and HSV]. Each of the
different personalities can be accessed from the control panel. Please see section on “Control Panel Functions” on a
description on how to accomplish this.
[STAG]
CHANNEL
DESCRIPTION
1
Dimmer
2
Red (step time when cus.01~10 in ch.8 is activated)
3
Green(fade time when cus.01~10 in ch.8 is activated)
4
Blue
5
White
6
Color Macro / White Balance / Hyper Color
7
Strobe
8
Auto & Custom Programs
9
Auto Speed Adjustment
10
Dimmer Speed
11
ID Address Selection
[ARC.1]
CHANNEL
DESCRIPTION
1
Red
2
Green
3
Blue
[AR1.D]
CHANNEL
DESCRIPTION
1
Dimmer
2
Red
3
Green
4
Blue
[ARC.2]
CHANNEL
DESCRIPTION
1
Red
2
Green
3
Blue
4
White

COLORado™ 2 User Manual 7 2/18/2009 12:45 PM
[AR2.D]
CHANNEL
DESCRIPTION
1
Dimmer
2
Red
3
Green
4
Blue
5
White
[AR2.S]
CHANNEL
DESCRIPTION
1
Dimmer
2
Red
3
Green
4
Blue
5
White
6
Strobe
[HSV]
CHANNEL
DESCRIPTION
1
Hue
2
Saturation
3
Value (Intensity)

COLORado™ 2 User Manual 8 2/18/2009 12:45 PM
Power Link Out
DMX in
Power in
Power out
Control board
DMX out
Safety
attachment
Product Overview

COLORado™ 2 User Manual 9 2/18/2009 12:45 PM
Dimensions
Hanging
bracket/ floor
stand
Bracket adjustment
knob

COLORado™ 2 User Manual 10 2/18/2009 12:45 PM
3. SETUP
AC Power
This fixture has an auto-switching switch-mode power supply that can accommodate a wide range of
input voltages. The only thing necessary to do before powering on the unit is to make sure the line
voltage you are applying is within the range of accepted voltages. This fixture will accommodate
between 100V and 240V AC 50-60 Hz. All fixtures must be powered directly off a switched circuit and
cannot be run off a rheostat (variable resistor) or dimmer circuit, even if the rheostat or dimmer
channel is used solely for a 0% to 100% switch.
This fixture is designed for power linking from one COLORado™ 2 to another COLORado™ 2 fixture.
Each fixture ships with IP-66 proprietary power input cables. Each fixture ships with a power adapter
to Male Edison connector.
Warning! All fixtures must be connected to circuits with a suitable Earth Ground.
Depending on the application, the lighting fixture may require a different connector Please refer to the
below wire color code if installing a new connector.
Wire
Connection
Brown
AC Live
Blue
AC Neutral
Green/Yellow
AC Ground
Connection
Pin
AC Live
1
AC Neutral
2
Ground(Earth)
3

COLORado™ 2 User Manual 11 2/18/2009 12:45 PM
Mounting
Orientation This fixture may be mounted in any safe position.
Rigging The fixture includes a mounting yoke to which a rigging clamp can be attached. You
must supply your own clamp and make sure the clamp is capable of supporting the
weight of this fixture. It is recommended to use at least 2 mounting points per
fixture. You can order “C” and “O”-clamps from any CHAUVET dealer or distributor
(CLP-15, CLP-06 recommended).
Note: There are 2 types of applications for this fixture: floor stand for up lighting, and
overhead use for down lighting. If you are using this fixture for up lighting, then you must
use at least 1 safety cable/chain for each fixture in addition to the mounting brackets.
1. If hanging the fixture for over head use, then please follow the below steps.
2. Block access below the work area and use suitable and stable platform
when installing or servicing fixture.
3. Safety cables must always be used, secured through safety cable
attachment. The safety cable must be capable of holding 10 times the weight
of the fixture.
4. Verify the structure can hold 10 times the weight of all to-be installed
fixtures.
Caution! After prolonged periods of operation, the fixture chassis may reach high
temperatures. This fixture must be mounted in a ventilated location, as it
is convection cooled.
Hanging Clamp
Note: sold separately
Safety Cable
Note: the cable must be
secured through the heat
sink ventilation
passageway.

COLORado™ 2 User Manual 12 2/18/2009 12:45 PM
Lens Assembly Installation/Replacement
The COLORado™2 comes with 15 lens assembly pre-installed from the factory. However, there is 1 other optional
lens kit available (CL20X30), which is the 30 degree. This is available as an accessorie, and will alter the beam
angle. Please follow the below instructions for proper replacement/installation.
1. Remove the gel frame holder by removing the 4 thumbscrews.
2. Remove the front cover (black) by removing the 8 Phillips #2 screws that hold it in place. Use
caution, because the glass is not secured under this cover and may fall loose.
3. Now, remove the glass cover.
4. After removing the glass cover, remove the screws that hold the lens assembly in place. There
are 6 Phillips #2 screws that secure this assembly in position.
Note: use care when performing this procedure, as this gives you direct access to
the LEDs, which are very fragile.
5. You now should have full access to the lens assembly. This must be removed and the old lenses
must be replaced with the new lenses. The same assembly is to be reinstalled with the new
lenses in place and the process is complete.
Warning! 1. When replacing the lens assembly, please make sure that the power is
disconnected from the fixture beforehand.
2. You must also be VERY CAREFUL when opening this fixture. Improper handling
on the behalf of the user may void the IP-66 rating of this fixture.
4. Lens assembly
Watertight seal
3. Glass cover
2. Front cover

COLORado™ 2 User Manual 13 2/18/2009 12:45 PM
Fixture Linking
You will need a serial data link to run light shows of one or more fixtures using a DMX-512 controller
or to run synchronized shows on two or more fixtures set to a master/slave operating mode. The
combined number of channels required by all the fixtures on a serial data link determines the number
of fixtures the data link can support.
Important: Fixtures on a serial data link must be daisy chained in one single line. To comply with the EIA-485
standard no more than 32 devices should be connected on one data link. Connecting more than 32
fixtures on one serial data link without the use of a DMX optically-isolated splitter may result in
deterioration of the digital DMX signal.
Maximum recommended serial data link distance: 500 meters (1640 ft.)
Maximum recommended number of fixtures on a serial data link: 32 fixtures
Data Cabling
To link fixtures together you must obtain data cables. You can purchase CHAUVET-certified DMX
cables directly from a dealer/distributor or construct your own cable. If you choose to create your own
cable please use data-grade cables that can carry a high quality signal and are less prone to
electromagnetic interference.
DMX DATA CABLE
Use a Belden© 9841 or equivalent cable which meets the specifications for EIA RS-485 applications.
Standard microphone cables cannot transmit DMX data reliably over long distances. The cable will
have the following characteristics:
2-conductor twisted pair plus a shield
Maximum capacitance between conductors –30 pF/ft.
Maximum capacitance between conductor and shield –55 pF/ft.
Maximum resistance of 20 ohms / 1000 ft.
Nominal impedance 100 –140 ohms
CABLE CONNECTORS
Cabling must have a male XLR connector on one end and a female XLR connector on the other end.
CAUTION Do not allow contact between the common and the fixture’s chassis ground. Grounding the common can
cause a ground loop, and your fixture may perform erratically. Test cables with an ohm meter to verify
correct polarity and to make sure the pins are not grounded or shorted to the shield or each other.
COMMON
DMX +
DMX -
INPUT
OUTPUT
1
3
2
1
3
2
1
3
2
Resistance 120
ohm 1/4w between
pin 2 (DMX -) and
pin 3 (DMX +) of
the last fixture.
Termination reduces signal errors. To
avoid signal transmission problems
and interference, it is always
advisable to connect a DMX signal
terminator.
DMX c
o
n
n
e
c
t
o
r
c
o
n
f
i
g
u
r
a
t
i
o
n

COLORado™ 2 User Manual 14 2/18/2009 12:45 PM
This drawing provides a
general illustration of the
DMX Input/Output panel of
a lighting fixture.
Universal DMX Controller
Continue the link
Often, the setup for Master-Slave
and Standalone operation requires
that the first fixture in the chain be
initialized for this purpose via either
settings in the control panel or DIP-
switches. Secondarily, the fixtures
that follow may also require a slave
setting. Please consult the
“Operating Instructions” section in
this manual for complete instructions
for this type of setup and
configuration.
Master
Slave
Slave
3-PIN TO 5-PIN CONVERSION CHART
Note! If you use a controller with a 5 pin DMX output connector, you will need to use a 5 pin to 3 pin adapter.
CHAUVET Model No: DMX5M, or DMX5F.
The chart below details a proper cable conversion:
3PIN TO 5PIN CONVERSION CHART
Conductor
3 Pin Female (output)
5 Pin Male (Input)
Ground/Shield
Pin 1
Pin 1
Data ( - ) signal
Pin 2
Pin 2
Data ( + ) signal
Pin 3
Pin 3
Do not use
Do not use
Do not use
Do not use
Setting up a DMX Serial Data Link
1. Connect the (male) 3 pin connector side of
the DMX cable to the output (female) 3 pin
connector of the controller.
2. Connect the end of the cable coming from
the controller which will have a (female) 3
pin connector to the input connector of the
next fixture consisting of a (male) 3 pin
connector.
3. Then, proceed to connect from the output
as stated above to the input of the following
fixture and so on.
CHAUVET Certified DMX Data Cables
Order Code Description
DMX1.5 DMX Cable 1.5m/4.9ft
DMX4.5 DMX Cable 4.5m/14.8ft
DMX10 DMX Cable 10m/32.8ft
Master/Slave Fixture Linking
1. Connect the (male) 3 pin connector side of the DMX cable to the output (female) 3 pin connector
of the first fixture.
2. Connect the end of the cable coming from the first fixture which will have a (female) 3 pin
connector to the input connector of the next fixture consisting of a (male) 3 pin connector. Then,
proceed to connect from the output as stated above to the input of the following fixture and so on.

COLORado™ 2 User Manual 15 2009-02-18 12:45 PM
4. OPERATING INSTRUCTIONS
Control Options
The COLORado™ 2 is addressable in the DMX range of 001 to 512. In its simplest control form, this
allows for the control of up to 46 fixtures in the 11-channel “STAG”personality; however, a secondary
“ID” address system exists for use in a limited DMX universe and architectural environments. The “ID”
address system allows the user to assign up to 66 fixtures within the same DMX address; in effect,
multiplying the control of COLORado’s™ within a single universe to 3,696 fixtures. The
COLORado’s™ “ID” address system is accessed using DMX channel 11 [STAG]. Consideration must
be placed when programming live performances or cues that need to trigger on demand or on a time
line. So, to remain within one second execution time, program no greater than 10 fixtures on ID
addressing per DMX channel.
COLORado ™ Control Quick Setup
For detailed instructions on display panel operations and functions please advance to the section
titled; “Display Panel Functions”. These steps assume that you have read and are familiar with setting
up a DMX serial data link.
DMX-512 control without “ID” address
The COLORado™ 2 operates on 11 channels of DMX (“STAG” personality). Address each fixture in
increments of 9 channels. (I.e. 1,12,23,34, etc…) To save time you can use the same DMX address
for each fixture. All fixtures will then respond simultaneously to control. You may also group your
fixtures and address those groups alike for faster programming and control.
1. Access the control panel function by pressing the (MENU) button until the {RUN MODE} is
displayed.
2. Press (SET) and use the (UP/DOWN) buttons to select {DMX} function.
3. Then, Press (MENU) button until {DMX512 ADDRESS} is displayed.
4. Pres the (SET) button.
6. Use the (UP/DOWN) buttons to increase or decrease channels between 001 and 512.
7. Press the (SET) button to confirm action. Then press (MENU) to exit.
Deactivate ID addressing in each fixture by setting panel function {ID ON/OFF} to OFF.
{MENU} {SETTINGS} {ID ON/OFF} [OFF]
Notes: If ID addressing is not deactivated in the fixture’s control panel function, unintended results may occur if
values are present in channel 11. Make sure values on channel 9 are set to “0”.

COLORado™ 2 User Manual 16 2009-02-18 12:45 PM
DMX Address: 001
ID Address: 01
DMX Address: 001
ID Address: 02
DMX Address: 001
ID Address: 03
DMX Address: 013
ID Address: 01
DMX Address: 013
ID Address: 02
DMX Address: 013
ID Address: 03
DMX 512 Controller
The figure above shows a simple DMX layout which has used three units at each
DMX address. The three units have different ID addresses which allows the user to
collectively control the whole group of units at that DMX address by setting Channel
10 to 0, or to control each unit independently by first selecting the DMX address and
then by using Channel 11 to locate the target ID address. (Note that when using ID
addresses it is also possible to activate ADAS which allows for even more option with
DMX addressing and control.
DMX-512 addressing with ID address
1. Follow instructions 1 ~ 4 for DMX512 addressing.
2. Activate ID addressing in each fixture by setting panel function {ID ON/OFF} to ON.
{MENU} {Settings) {ID ON/OFF} [ON]
3. For every DMX512 starting address the user can set 66 separate ID addresses.
4. Set ID addresses in each fixture by setting panel function {ID address} to incremental values.
(I.e. 1,2,3,4,5,6,etc…)
{MENU} {Settings} {ID address} [01 ~ 66]
5. ID addresses are accessible using Channel 9 [STAG].

COLORado™ 2 User Manual 17 2009-02-18 12:45 PM
MENU
UP
DOWN
SET
Setting the DMX address
Each fixture requires a "start address" from 1 to 512. A fixture requiring one or more channels for
control begins to read the data on the channel indicated by the start address. For example, a fixture
that occupies or uses 7 channels of DMX and was addressed to start on DMX channel 100, would
read data from channels: 100, 101, 102, 103, 104, 105 and 106. Choose start addresses so that the
channels used do not overlap and note the start address selected for future reference. The
COLORado™ 2 uses up to11 channels of DMX. If this is your first time using DMX, we recommend
reading the DMX Primer in the Appendix Section.
Control Panel Functions
All fixture functions and settings are accessible via the built-in control panel interface.
BUTTON
FUNCTION
MENU
Exits from the current menu or function
SET
Enables the currently displayed menu or sets the currently selected value in to the
selected function
UP
Navigates upwards through the menu list and increases the numeric value when in a
function
DOWN
Navigates downwards through the menu list and decreases the numeric value when
in a function

COLORado™ 2 User Manual 18 2009-02-18 12:45 PM
Menu Map
MAIN FUNCTION
SUB-FUNCTION
SELECTION
INSTRUCTION
1. Static Color
Dimmer
000 ~ 255*
(0 ~ 100%)
*Strobe range is
0~20
User can combine Red, Green and Blue
to generate a custom color
Select strobing frequency between 0
and 20Hz
Red
Green
Blue
Color Macros
Strobe
2. Auto
Auto
(1~10)
Choose from 10 automatic programs
Personal
(1~10)
Choose from 10 programs that be
customized under the “edit custom”
menu option
3. DMX Address
001 ~ 512
Sets the DMX starting address
4. Run Mode
DMX~Slave
Sets the operating mode for the fixture:
to receive signal from a DMX controller
(DMX) or to receive signal from the DMX
out of another COLORado Panel (Slave)
5. Personality
HSV
3-channel: hue, saturation, value
STAG
11-channel RGBW+D
Arc.1
3-channel RGB
Ar1.d
4-channel RGB+D
Arc 2
4-channel RGBW
Ar2.d
5-channel RGBW+D
Ar2.s
6-channel RGBW+D+strobe
6. ID Address
0-66
Assigns the ID address to a fixture
7. Settings
ID
On~Off
Enables or disables ID ADAS
Upload
*Password required
Performs an upload of the custom
programs to another fixture. Displays
“End!” when successful
Dimmer
Off
Select linear dimmer by [off] or special
dimmer speed [dim1~4]
[dim1] is the fastest dimming curve, and
[dim4] is the slowest dimming curve
dim 1
dim 2
dim 3
dim 4
Power
Normal~High
Enables HyperColor™mode
RGB to White
Yes~No
Enables or disables RGB to White
RESET Parameter
*Password required
Performs a factory reset
8. Key-Lock
On~Off
Enables or Disables password lockout
9. Edit Custom
Custom (1~10)
-(Scene 01-30)
Red
(0~255)
Green
Blue
White
Strobe
(0~20)
Time
(0~255)
Fade
(0~255)
10. Calib.
White (1~11)
Red
Sets Custom White Balance by
adjusting the maximum fader value
(0~255)
Green
Blue
White
RGB to White
On ~ Off
This setting presets and switches RGB
to full power (Off) or RGB auto-mix to
white (On)

COLORado™ 2 User Manual 19 2009-02-18 12:45 PM
DMX512 Channel Values
The COLORado™ 2 has 7 DMX512 channel configurations [HSV, STAG, ARC1, ARC1+D, ARC2,
ARC2+D, and Ar2.s].
STAG
CHANNEL
VALUE
FUNCTION
1
000 255
Dimmer
0 100%
2
000 255
Red
(or STEP TIME when CUS.01-10 is activated)
0 100%
3
000 255
Green
(or FADE TIME when CUS.01-10 is activated)
0 100%
4
000 255
Blue
0 100%
5
000 255
White
0 100%
6
000 005
006 020
021 030
031 050
051 070
071 090
081 095
091 110
111 130
131 150
151 170
171 190
191 200
201 205
206 210
211 215
216 220
221 225
226 230
231 235
236 240
241 245
246 250
251 255
Color Macro + White Balance + HyperColor™
No Function
HyperColor™Mode (only in Normal power mode)
No Function
Red 100%/ Green Up/ Blue 0%
Red Down/ Green 100%/ Blue 0%
Red 0%/ Green 100%/ Blue Up
Red 100%/ Green 0%/ Blue Down
Red 0%/ Green Down/Blue 100%
Red Up/ Green 0%/Blue 100%
Red 100%/ Green 0%/ Blue Down
Red 100%/ Green Up/ Blue Up
Red Down/ Green Down/ Blue 100%
RGBW 100%
White 1:3200K
White 2: 3400K
White 3: 4200K
White 4: 4900K
White 5: 5600K
White 6: 5900K
White 7: 6500K
White 8: 7200K
White 9: 8000K
White 10: 8500K
White 11: 10000K
7
000 004
005 255
Strobe
No Function
0 20Hz

COLORado™ 2 User Manual 20 2009-02-18 12:45 PM
8
000 009
010 019
020 029
030 039
040 049
050 059
060 069
070 079
080 089
090 099
100 109
110 119
120 129
130 139
140 149
150 159
160 169
170 179
180 189
190 199
200 255
Auto + Custom Programs
No Function
Auto 1
Auto 2
Auto 3
Auto 4
Auto 5
Auto 6
Auto 7
Auto 8
Auto 9
Auto 10
Custom 1
Custom 2
Custom 3
Custom 4
Custom 5
Custom 6
Custom 7
Custom 8
Custom 9
Custom 10
9
000 255
Auto Speed Adjustment
(only when using ch.8)
0 100%
10
000 009
010 069
070 129
130 189
190 255
Dimmer Speed
Linear dimming curve
Nonlinear dimming curve 1 (fastest)
Nonlinear dimming curve 2
Nonlinear dimming curve 3
Nonlinear dimming curve 4 (slowest)
CHANNEL 11 (ID ADDRESS SELECTION)
000 009
010 019
020 029
030 039
040 049
050 059
060 069
070 079
080 089
090 099
100 109
110 119
120 129
130 139
140 149
150 159
160 169
170 179
180 189
190 199
200 209
210
211
All IDs
ID 1
ID 2
ID 3
ID 4
ID 5
ID 6
ID 7
ID 8
ID 9
ID 10
ID 11
ID 12
ID 13
ID 14
ID 15
ID 16
ID 17
ID 18
ID 19
ID 20
ID 21
ID 22
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
ID 23
ID 24
ID 25
ID 26
ID 27
ID 28
ID 29
ID 30
ID 31
ID 32
ID 33
ID 34
ID 35
ID 36
ID 37
ID 38
ID 39
ID 40
ID 41
ID 42
ID 43
ID 44
ID 45
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
ID 46
ID 47
ID 48
ID 49
ID 50
ID 51
ID 52
ID 53
ID 54
ID 55
ID 56
ID 57
ID 58
ID 59
ID 60
ID 61
ID 62
ID 63
ID 64
ID 65
ID 66