Chauvet SlimPAR Pro Tri User manual

User Manual

Page 2 of 15 SlimPAR™ 38 User Manual Rev. 3
TABLE OF CONTENTS
1. BEFORE YOU BEGIN............................................................................................................................................................3
WHAT IS INCLUDED......................................................................................................................................................................3
UNPACKING INSTRUCTIONS...........................................................................................................................................................3
MANUAL CONVENTIONS................................................................................................................................................................3
ICONS........................................................................................................................................................................................3
SAFETY INSTRUCTIONS.................................................................................................................................................................4
2. INTRODUCTION ....................................................................................................................................................................5
CONTROL FEATURES...................................................................................................................................................................5
Additional Features...................................................................................................................................................................................... 5
PRODUCT OVERVIEW...................................................................................................................................................................5
3. SETUP ....................................................................................................................................................................................6
ACPOWER ................................................................................................................................................................................6
POWER LINKING..........................................................................................................................................................................6
MOUNTING.................................................................................................................................................................................7
Orientation................................................................................................................................................................................................... 7
Rigging........................................................................................................................................................................................................ 7
SIGNAL LINKING ..........................................................................................................................................................................8
4. OPERATING INSTRUCTIONS..............................................................................................................................................9
Control Panel Functions............................................................................................................................................................................... 9
Menu Map................................................................................................................................................................................................... 9
Configuring the Starting Address................................................................................................................................................................ 10
DMX Operation.......................................................................................................................................................................................... 10
Master/Slave (Standalone Operating Modes).............................................................................................................................................. 10
STANDALONE OPERATION...........................................................................................................................................................11
Automatic.................................................................................................................................................................................................. 11
Sound-Active............................................................................................................................................................................................. 11
Preset Colors............................................................................................................................................................................................. 11
Custom Static Colors................................................................................................................................................................................. 11
DMX CHANNEL VALUES.............................................................................................................................................................12
7-CH Mode................................................................................................................................................................................................ 12
3-CH Mode................................................................................................................................................................................................ 12
5. APPENDIX............................................................................................................................................................................13
GENERAL TROUBLESHOOTING.....................................................................................................................................................13
GENERAL MAINTENANCE ............................................................................................................................................................13
RETURN PROCEDURE ................................................................................................................................................................14
CLAIMS....................................................................................................................................................................................14
TECHNICAL SPECIFICATIONS .............................................................................................................................................15
CONTACT US...........................................................................................................................................................................15

SlimPAR™ 38 User Manual Rev. 3 Page 3 of 15
1. BEFORE YOU BEGIN
What is Included
•1 x SlimPAR™ 38
•1 x Power Cord
•1 x Warranty Card
•1 x Quick Reference Guide
Unpacking Instructions
Immediately upon receiving a fixture, carefully unpack the carton, check the contents to ensure
that all parts are present, and have been received in good condition. Notify the shipper
immediately and retain packing material for inspection if any parts appear damaged from
shipping or the carton itself shows signs of mishandling. Save the carton and all packing
materials. In the event that a fixture must be returned to the factory, it is important that the fixture
be returned in the original factory box and packing.
Manual Conventions
CHAUVET® manuals use the following conventions to differentiate certain types of information
from the regular text.
CONVENTION MEANING
[10] A DIP switch to be configured
<Menu> A key to be pressed on the fixture’s control panel
1~512 A range of values
50/60 A set of values of which only one can be chosen
Settings A menu option not to be modified (for example, showing the operating
mode/current status)
MENU >
Settings A sequence of menu options to be followed
ON A value to be entered or selected
Icons
This manual uses the following icons to indicate information that requires special attention on the
part of the user.
ICONS MEANING
This paragraph contains critical installation, configuration or operation
information. Failure to comply with this information may render the fixture
partially or completely inoperative, cause damage to the fixture or cause
harm to the user.
This paragraph contains important installation or configuration information.
Failure to comply with this information may prevent the fixture from
functioning correctly.
This paragraph reminds you of useful, although not critical, information.

Page 4 of 15 SlimPAR™ 38 User Manual Rev. 3
Safety Instructions
•Please keep this User Manual for future consultation. If you sell the unit to another
user, be sure that they also receive this instruction booklet.
•Always make sure that you are connecting to the proper voltage, and that the line
voltage you are connecting to is not higher than that stated on the decal or rear panel
of the fixture.
•This product is intended for indoor use only! To prevent risk of fire or shock, do not
expose fixture to rain or moisture.
•Make sure there are no flammable materials close to the unit while operating.
•The unit must be installed in a location with adequate ventilation, at least 20 in (50 cm)
from adjacent surfaces. Be sure that no ventilation slots are blocked.
•Always disconnect from power source before servicing or replacing fuse and be sure to
replace with same fuse source.
•Secure fixture to fastening device using a safety chain.
•Maximum ambient temperature (Ta) is 104° F (40° C). Do not operate fixture at
temperatures higher than this.
•In the event of a serious operating problem, stop using the unit immediately. Never try
to repair the unit by yourself. Repairs carried out by unskilled people can lead to
damage or malfunction. Please contact the nearest authorized technical assistance
center.
•Never connect the device to a dimmer pack.
•Make sure the power cord is never crimped or damaged.
•Never disconnect the power cord by pulling or tugging on the cord.
•Never carry the fixture directly from the cord. Always use the hanging/mounting
bracket.
•Avoid direct eye exposure to the light source while it is on.
Please read these instructions carefully. It includes important information
about the installation, usage and maintenance of this product.

SlimPAR™ 38 User Manual Rev. 3 Page 5 of 15
2. INTRODUCTION
Control Features
•3 or 7-channel DMX-512 slim LED par can
•Operating modes:
3-channel: RGB control
7-channel: RGB, macros, run/strobe speed, automatic/sound, dimmer
•Static colors and RGB color mixing with or without DMX controller
•Built-in automated programs via master/slave or DMX with variable speed
•Built-in sound activated programs via master/slave or DMX
•
Pulse effect with adjustable speed
Additional Features
•Low-profile lights are 2.5 in deep
•Power linking: max 43 units
•Double-bracket yoke doubles as floor stand
Product Overview
Microphone
Control Panel
Power In
Microphone
Sensitivity
Adjustment Knob
DMX In
Power Out
DMX Out

Page 6 of 15 SlimPAR™ 38 User Manual Rev. 3
3. SETUP
AC Power
This fixture runs on 100~240 VAC, 50/60 Hz. Before powering on the unit, make sure the line
voltage to which you are connecting it is within the range of accepted voltages.
To determine the power requirements for a particular fixture, see the label affixed to the back
plate of the fixture or refer to the fixture’s specifications chart. A fixture’s listed current rating
indicates its average current draw under normal conditions.
Always connect the fixture to a switched circuit. Never connect the fixture to a rheostat
(variable resistor) or dimmer circuit, even if the rheostat or dimmer channel is used only
as a 0 to 100% switch.
Always connect the fixture to a circuit with a suitable electrical ground.
Power Linking
This fixture contains power linking via the Edison outlet located on the back panel. Please see
the diagram below for further explanation.
The maximum quantity of fixtures that may be linked is 43.
The power linking shown in this document is for the Chauvet® North American version
ONLY! Therefore, it is the customer’s responsibility to check with the Dealer/Distributor
regarding power linking on the local version of the product. Connections and availability
may change, depending on the power requirements and/or regulations of each
country/region.
Additional power
link out
Fixture #1
Fixture #2
Fixture #3

SlimPAR™ 38 User Manual Rev. 3 Page 7 of 15
Mounting
Orientation
The SlimPAR™ 38
may be mounted in any safe position.
Rigging
Be sure that the structure can support the weight of the fixture. Please see the “Technical
Specifications” section of this manual for a detailed weight listing. Mount the fixture securely. This
may be done with a screw, nut and bolt, or a hanging clamp. The hole in each bracket is 13 mm
in size. When rigging consider routine maintenance and control panel access. Please see the
following steps for installation.
•If the power link out is intended to be used with multiple fixture, take into account the
length of each power cable, and mount the fixtures close enough to one another to
accommodate for this.
•When aiming the fixtures, you may use the bracket adjustment knob. Loosen the knob,
adjust to the desired angle, and then tighten the knob by turning clockwise. Do not use
tools for this step, as it may cause damage.
•There is a secondary portion of the bracket, which may be used primarily for floor
standing positions.
•
Safety cables must always be used.
Mounting
Bracket
Secondary bracket
(used primarily for
standing position)
Do not use a tool on
the bracket
adjustment knob

Page 8 of 15 SlimPAR™ 38 User Manual Rev. 3
DMX controller
(only in DMX operation)
Signal Linking
In order to use this fixture in a DMX or master/slave operation, you must daisy chain, using DMX
cables to link from one fixture to another.
Additional signal
link out
Fixture #2
Fixture #3
Fixture #1

SlimPAR™ 38 User Manual Rev. 3 Page 9 of 15
4. OPERATING INSTRUCTIONS
Control Panel Functions
Access control panel functions using the four buttons located directly underneath the LED display on the control panel.
BUTTON
FUNCTION
<MENU>
Used to scroll through the
current operating mode, as
well as back out of the
current menu option
<UP> Used to select increasing
advancement in the value
<DOWN> Used to select decreasing
advancement in the value
<ENTER> Used to select a value and
store it to memory
The Control Panel shows the current state of the unit. It is used to select the operating mode, as well as the sub-features.
For a detailed layout of the control panel functions, please see the “menu map” section below.
Menu Map
M
AIN
FUNCTION
S
UB
-
FUNCTION
SELECTION
SUB-SELECTION
INSTRUCTION
P--
P1
7 Color Switching
Select between 2 switching
and 2 fading built-in
programs
P2
7 Color Fading
P3
3 Color Switching
P4
3 Color Fading
P5 7 Color sound active
Use the Audio
Adjustment Knob
located on the back
of the fixture
Select between 2 sound
active programs
P6 3 Color sound active
3-CH d001~d512
Select 3-channel DMX
mode (RGB control)
7-CH d001~d512
Select 7-channel DMX
mode: RGB, macros, run
speed, strobe,
automatic/sound, dimmer
C--
C1
Red
Select between 7 static
colors. The display will
read C1~C7. The colors
that each of these
represent are indicated to
the left.
C2
Green
C3
Blue
C4
Cyan
C5
Magenta
C6
Yellow
C7
White
S-- S001~S100 (the default range is S050)
This is the speed range for
the 4 switching and fading
built-in programs
U--
r---
Red
000~100
Combine red, green, and
blue to create a custom,
static color
g---
Green
B---
Blue
MENU UP DOWN ENTER

Page 10 of 15 SlimPAR™ 38 User Manual Rev. 3
Configuring the Starting Address
Each fixture requires a starting address from 1~512. A fixture requiring one or more channels for
control begins to read the data on the channel indicated by the starting address. For example, a
fixture that uses seven DMX channels and is addressed to start on DMX channel 100, will read
data from channels: 100, 101, 102, 103, 104, 105 and 106. Choose the starting addresses for
each fixture so that the channels used do not overlap. In addition, you should note the starting
address selected for future reference.
The SlimPAR™ 38uses seven or three DMX channels. If this is your first time using DMX, we
recommend reading the “DMX Primer” section in the “Appendix”.
DMX Operation
This is the operating mode which will allow for control with an external DMX controller. You must
set the starting address for this mode. If this is your first time using DMX, then it is recommended
that you refer to the “DMX Primer” section in the “Appendix” of this manual.
1. Press <MENU> until 3-CH or 7-CH appears on the LED screen.
2. Press <ENTER>.
3. Using <UP> and <DOWN>, select the desired DMX address (d001~d512).
Master/Slave (Standalone Operating Modes)
This is the operating mode which will allow one fixture to act as the “master” and control all of the
other “slave” fixtures. You must set both the master and the slave(s) fixtures to the correct mode
for this operation.
Master Settings:
1. Connect the fixtures with DMX cables, as shown in the “Fixture Linking” section.
2. Use any one of the standalone modes for the master unit.
This includes: P--, C--, and U--
Slave Settings:
1. Press <MENU> until 3-CH or 7-CH appears on the LED screen.
2. Press <ENTER>.
3. Using <UP> and <DOWN>, set the DMX address to d001.
4. Press <ENTER>.
Although any fixture in the DMX daisy chain may be set to master, it is advisable to set the
master as the first fixture in the line.
Only one fixture may be set to master.
Do not connect a DMX controller to the daisy chain for this operating mode.
It does not matter which DMX mode is selected for the slave fixtures. Either mode will be
effective.

SlimPAR™ 38 User Manual Rev. 3 Page 11 of 15
Standalone Operation
Automatic
This fixture has preprogrammed chases. These are accessed via the control panel. The speed
may be adjusted for the chases. Please see the instructions below for further explanation.
1. Press <MENU> until P-- appears on the LED screen.
2. Press <ENTER>.
3. Using <UP> and <DOWN>, select the desired program (P1~P4).
4. Press <ENTER>.
5. Press <MENU> until S-- appears on the LED screen.
6. Using <UP> and <DOWN>, select the desired program speed (S001~S100).
7. Press <ENTER> to confirm settings.
Sound-Active
This fixture has preprogrammed sound triggered chases. These are accessed via the control
panel. The microphone sensitivity may be adjusted using the audio adjustment knob. Please see
the instructions below for further explanation.
1. Press <MENU> until P-- appears on the LED screen.
2. Press <ENTER>.
3. Using <UP> and <DOWN>, select the desired program (P5~P6).
4. Press <ENTER>to confirm settings.
Preset Colors
This fixture has preprogrammed static color presets. These are accessed via the control panel.
Please see the instructions below for further explanation.
1. Press <MENU> until C-- appears on the LED screen.
2. Press <ENTER>.
3. Using <UP> and <DOWN>, select the desired color preset (C1~C7).
4. Press <ENTER> to confirm settings.
Custom Static Colors
This fixture has the ability to accept custom static color settings. These are accessed via the
control panel. Please see the instructions below for further explanation.
1. Press <MENU> until U-- appears on the LED screen.
2. Press <ENTER>.
3. Using <UP> and <DOWN>, select the desired color (r, G, b).
4. Press <ENTER>.
5. Using <UP> and <DOWN>, select the desired color value (000~100). By selecting 000,
the color will remain off.
6. Press <ENTER> to continue to the next color (r, G, b).
7. Using <UP> and <DOWN>, select the desired color value (000~100). By selecting 000,
the color will remain off.
8. Repeat steps 6 & 7 until the desired color is obtained. Press <ENTER> to save the final
color setting. This will move the selection to the following color; however, this is necessary
to save the modification.
The colors are represented by the following in the menu map:
r--- = Red (000~100)
G--- = Green (000~100)
b--- = Blue (000~100)

Page 12 of 15 SlimPAR™ 38 User Manual Rev. 3
DMX Channel Values
7-CH Mode
CHANNEL
VALUE
FUNCTION
1
000 ó255
Red
Dimmer: 0%~100%
2
000 ó255
Green
Dimmer: 0%~100%
3
000 ó255
Blue
Dimmer: 0%~100%
4 000 ó015
016 ó255
Color Macros (override CH.1~3)
No Function
Color Macros
5
000 ó255
Speed (CH.6 @ values 32~223)
Slow~Fast
000 ó015
016 ó255
Strobe (RGB mode only)
No Function
Slow~Fast
6
000 ó031
032 ó063
064 ó095
096 ó127
128 ó159
160 ó191
192 ó223
224 ó255
Mode
RGB mode
Pulse effect 0%~100% (using RGB faders)
Pulse effect 100%~0% (using RGB faders)
Pulse effect 100%~0%~100% (using RGB faders)
Auto fade transition
Auto snap transition (3 colors)
Auto snap transition (7 colors)
Sound triggering mode
When CH.6 is set
between 032~223,
CH.5 controls the
speed.
7
000 ó255
Dimmer
Intensity: 0%~100% (RGB/Macro modes)
3-CH Mode
CHANNEL
VALUE
FUNCTION
1
000 ó255
Red
Dimmer: 0%~100%
2
000 ó255
Green
Dimmer: 0%~100%
3
000 ó255
Blue
Dimmer: 0%~100%

SlimPAR™ 38 User Manual Rev. 3 Page 13 of 15
5. APPENDIX
General Troubleshooting
SYMPTOM
POSSIBLE CAUSE(S)
POSSIBLE ACTION(S)
Breaker/Fuse keeps
blowing
Excessive circuit load
Check total load placed on the electrical
circuit.
Short circuit along the power wires Check for a short in the electrical wiring
(internal and/or external).
Device does not power
up
No power
Check for power on Mains.
Loose power cord Check power cord
Fixture is not responding
to DMX
Wrong DMX addressing
Check Control Panel and unit addressing
Damaged DMX cables
Check DMX cables
Wrong polarity settings on the controller
Check polarity switch settings on the
controller
Loose DMX cables
Check cable connections
Faulty DMX interface
Replace DMX input
Faulty Main PCB
Replace Main PCB
Loss of signal
Non DMX cables
Use only DMX compatible cables
Bouncing signals
Install terminator as suggested.
Long cable / Low level signal
Install amplifier right after fixture with strong
signal.
Too many fixtures
Install an optically coupled DMX splitter after
unit #32.
Interference from AC wires
Keep DMX cables separated from power
cables or black lights.
If you still have a problem after trying the above solutions, please contact CHAUVET® Technical
Support.
General Maintenance
To maintain optimum performance and minimize wear, fixtures should be cleaned frequently. Usage and
environment are contributing factors in determining frequency. As a general rule, fixtures should be cleaned at
least twice a month. Dust build-up reduces light output performance and can cause overheating. This can lead
to reduced lamp life and increased mechanical wear. Be sure to power off fixture before conducting
maintenance.
•Unplug fixture from power.
•Use a vacuum or air compressor and a soft brush to remove dust collected on external vents.
•Clean all glass when the fixture is cold with a mild solution of glass cleaner or Isopropyl Alcohol and a
soft lint free cotton cloth or lens tissue.
•Apply solution to the cloth or tissue and drag dirt and grime to the outside of the lens.
•Gently polish optical surfaces until they are free of haze and lint.
The cleaning of external optical lenses and/or mirrors must be carried out periodically to optimize light output.
Cleaning frequency depends on the environment in which the fixture operates. Damp, smoky or particularly
dirty surroundings can cause greater accumulation of dirt on the unit’s optics. Clean with soft cloth using normal
glass cleaning fluid. Clean the external optics at least every 20 days. Clean the fixture at least every 30/60
days.
Always dry the parts carefully after cleaning them.
Never spin a fan using compressed air.

Page 14 of 15 SlimPAR™ 38 User Manual Rev. 3
Return Procedure
Returned merchandise must be sent prepaid and in the original packing; call tags will not
be issued. Package must be clearly labeled with a Return Merchandize Authorization
Number (RMA #). Products returned without the RMA # will be refused. Call CHAUVET®
and request an RMA # prior to shipping the fixture. Be prepared to provide the model
number, serial number and a brief description of the cause for the return. Be sure to pack
fixture properly; any shipping damage resulting from inadequate packaging is the
customer’s responsibility. CHAUVET® reserves the right to use its own discretion to repair
or replace product(s). FedEx packing or double-boxing are recommended.
If you are given an RMA #, please include the following information on a piece of
paper inside the box:
1) Your name
2) Your address
3) Your phone number
4) RMA #
5) A brief description of the symptoms
Claims
Damage incurred in shipping is the responsibility of the shipper; therefore, the damage
must be reported to the carrier upon receipt of merchandise. It is the customer's
responsibility to notify and submit claims with the shipper in the event that a fixture is
damaged due to shipping. Any other claimfor items such as missing component/part,
damage not related to shipping, and concealed damage, must be made within seven (7)
days of receiving merchandise.

SlimPAR™ 38 User Manual Rev. 3 Page 15 of 15
TECHNICAL SPECIFICATIONS
WEIGHT & DIMENSIONS
Length ................................................................................................................7.3 in (185 mm)
Width..................................................................................................................8.1 in (206 mm)
Height...................................................................................................................2.5 in (64 mm)
Weight.................................................................................................................1.8 lbs (0.8 kg)
POWER
Auto-ranging power supply..................................................................100~240 VAC, 50/60 Hz
Power Consumption @ 120 V....................................................9 W (0.1 A) max, 0.2 A inrush
Power Consumption @ 230 V....................................................9 W (0.1 A) max, 0.2 A inrush
Power output...........................................................................................................43 units max
Fuse ........................................................................................................................F 1 A, 250 V
SATELLITE OPERATION
Maximum run time (@ 100% RGB) .................................................................................10 hrs
INDOOR/OUTDOOR
Rating............................................................................................................For indoor use only
LIGHT SOURCE
LED .............................................................................................75 (25 red, 25 green, 25 blue)
PHOTO OPTIC
Lux @ 2 m.............................................................................................................................531
Beam angle............................................................................................................................17°
Field angle .............................................................................................................................29°
THERMAL
Maximum ambient temperature ..........................................................................104° F (40° C)
ORDERING INFORMATION
SlimPAR™ 38.........................................................................................................SLIMPAR38
WARRANTY INFORMATION
Warranty.................................................................................................2-year limited warranty
CONTACT US
World Wide
General Information CHAUVET®
5200 NW 108th Ave
Sunrise, FL 33351
voice: 954.577.4455
fax: [phone]
toll free: 800.762.1084
Technical Support CHAUVET®
5200 NW 108th Ave
Sunrise, FL 33351
voice: 954.577.4455(Press 4)
fax: [phone] (Attention: Service)
World Wide Web www.chauvetlighting.com