Chauvet Led Shadow User manual

0
USER MANUAL

LED Shadow™ User Manual Rev. 5 2
© CHAUVET®, 2014, All Rights Reserved
Information and specifications in this User Manual are subject to change without notice.
CHAUVET® assumes no responsibility or liability for any errors or inaccuracies
that may appear in this manual.
Table of Contents
1. BEFORE YOU BEGIN................................................................................................................................................... 3
UNPACKINGINSTRUCTIONS..............................................................................................................................................................................................3
IMPORTANT SAFETY INFORMATION...................................................................................................................................................................................4
2. INTRODUCTION ...........................................................................................................................................................5
FEATURES.......................................................................................................................................................................................................................5
PRODUCT OVERVIEW.......................................................................................................................................................................................................5
3. SETUP ..........................................................................................................................................................................7
ACPOWER .....................................................................................................................................................................................................................7
MOUNTING ......................................................................................................................................................................................................................7
FIXTURE LINKING.............................................................................................................................................................................................................8
Data Cabling............................................................................................................................................................................................................8
DMX Data Cable.................................................................................................................................................................................................8
CableConnectors...............................................................................................................................................................................................8
3-Pin to 5-Pin Conversion Chart........................................................................................................................................................................9
SETTING UP A DMXSERIAL DATA LINK............................................................................................................................................................................9
STANDALONE/MASTER-SLAVE FIXTURE LINKING ..............................................................................................................................................................9
4. OPERATING INSTRUCTIONS.................................................................................................................................... 10
STANDALONE MODE......................................................................................................................................................................................................10
Single-Fixture Mode...............................................................................................................................................................................................10
Master-Slave Mode................................................................................................................................................................................................10
Setup................................................................................................................................................................................................................10
Dipswitch Options..................................................................................................................................................................................................10
DMXCONTROL MODE...................................................................................................................................................................................................11
Configuring for DMX control..................................................................................................................................................................................11
Setting the DMX address.......................................................................................................................................................................................11
DAISYCHAIN (SERIAL DATA LINK)..................................................................................................................................................................................11
5. APPENDIX..................................................................................................................................................................12
DMXPRIMER................................................................................................................................................................................................................12
RETURNS PROCEDURE..................................................................................................................................................................................................12
CLAIMS .........................................................................................................................................................................................................................12
MAINTENANCE...............................................................................................................................................................................................................12
BINARY &DMXDIP-SWITCH ADDRESSING.....................................................................................................................................................................13
BINARY ADDRESSINGQUICK REFERENCECHART...........................................................................................................................................................14
DMXCHANNEL VALUES ................................................................................................................................................................................................15
TECHNICAL SPECIFICATIONS..........................................................................................................................................................................................15
CONTACT US................................................................................................................................................................. 16

LED Shadow™ User Manual Rev. 5 3
1. Before You Begin
Unpacking Instructions
Immediately upon receiving a product, carefully unpack the carton, check the contents to ensure that
all parts are present, and have been received in good condition. Notify the shipper immediately and
retain packing material for inspection if any parts appear damaged from shipping or the carton itself
shows signs of mishandling. Save the carton and all packing materials. In the event that a fixture
must be returned to the factory, it is important that the fixture be returned in the original factory box
and packing.
Note: If you should require sending any items back to CHAUVET®, call CHAUVET®
for a (RMA) Return Merchandise Authorization number. The factory will not
allow any shipments without an RMA.
Your shipment includes the following:
•LED Shadow™
•Power Cord
•Hanging Brackets with Mounting Hardware
•Warranty Card
•User Manual

Before You Begin
LED Shadow User Manual Rev. 5 4
Important Safety Information
This product is designed for professional use. It is not intended for use in a household environment.
This product presents risks of lethal or severe injury due to fire and heat, electric shock, ultraviolet
radiation, lamp explosion, and injury from falls. Read this manual before installing or powering the
fixture, follow the safety precautions listed below and observe all warnings in this manual and on the
fixture. If you have any questions about how to operate the fixture safely, please contact CHAUVET®.
Protection against Electric Shock
•Always disconnect from AC power source before servicing or replacing lamp or fuse and be sure
to replace with same lamp source.
•All Class I fixtures must be connected to circuits with a suitable Earth Ground.
•To prevent risk of fire or shock, do not expose fixture to rain or moisture. Make sure there are no
flammable materials close to the unit while operating.
•Do not operate the fixture if covers are open or if any internal component is missing or damaged:
an unshielded discharge lamp emits dangerous UV radiation that can cause burns and eye
damage.
•Make sure power cord is never crimped or damaged.
•Never disconnect power cord by pulling or tugging on the cord.
Protection against Fire & Burns
•This product is designed to be used with very specific lamp(s). Use of any other type of lamp not
stated in this manual may create a fire hazard due to possible risk of lamp explosion. Using the
wrong type of lamp in this product VOIDS the warranty.
•Always make sure that you are connecting to the proper voltage and that the line voltage you are
connecting to is not higher than that stated on decal or rear panel of the fixture.
•The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent
surfaces. Be sure that no ventilation slots are blocked.
•Maintain a minimum distance of 1 meter (3.28 feet) from combustible materials.
•Allow this product to cool for a minimum of 15 minutes before opening, handling or removing the
lamp in this product.
•Maximum ambient temperature is Ta: 104 °F (40 °C). Do not operate fixture at temperatures
higher than this.
Protection against exposure to (UV) Ultraviolet Radiation
•Avoid direct eye exposure to lamp while it is on.
•Do not operate the fixture if covers are open or if any internal component is missing or damaged.
Protection against Injury to persons
•Secure fixture to fastening device using a safety chain.
•A hot lamp is an explosion hazard. Do not open fixture for a minimum of 15 minutes after
switching off. Wear eye and hand protection when re-lamping.
•Fixture surface may reach temperatures of up to 320 °F (160 °C). Handle fixture after it has
reached room temperature.
•In the event of serious operating problem, stop using the unit immediately. Never try to repair the
unit by yourself. Repairs carried out by unskilled people can lead to damage or malfunction.
Please contact the nearest authorized technical assistance center. Always use the same type
spare parts.
Caution! There are no user-serviceable parts inside the unit. Do not open the housing or
attempt any repairs yourself. In the unlikely event your unit may require service,
please contact CHAUVET®.

LED Shadow™ User Manual Rev. 5 5
2. Introduction
Features
•3-channel DMX-512 LED UV blacklight
•Blackout/static/dimmer/strobe
•Built-in automatic programs
•Adjustable flash rate, dimmer and static via stand-alone
•Automatic built-in programs with sound-activation
•Linkable with LED Techno Strobe™ & LED Techno Strobe RGB™ in stand-alone
•Coverage up to 15 x 30 ft
•Low power consumption
•Additional power output for daisy chaining units together

Introduction
LED Shadow User Manual Rev. 5 6
DMX Input
DIP-switches
DMX Addressing
IEC Plug for AC Input
& Fuse Compartment
DMX Output
LED Front Panel
Hanging Yoke
Audio Sensitivity
Rotary knob
Red LED: Power Indicator
Blue LED: Signal Indicator
Power Output
Flush Mounting Bracket
Bracket
Adjustment Knobs
Product Overview

LED Shadow™ User Manual Rev. 5 7
Hanging Clamp
Flush Mounting Bracket
3. Setup
AC Power
Warning! Verify that the power requirement label on your unit matches the line voltage
applied. All fixtures must be connected to circuits with a suitable Earth Ground.
•To determine the power requirements for a particular fixture, see the label affixed to the back plate
of the fixture or refer to the fixture’s specifications chart.
•A fixture’s listed current rating is its average current draw under normal conditions.
•All fixtures must be powered directly off a switched circuit and cannot be run off a rheostat
(variable resistor) or dimmer circuit, even if the rheostat or dimmer channel is used solely for a
0 to 100% switch.
•Before applying power to a fixture, check that the source voltage matches the fixture’s
requirement.
•All fixtures must be connected to circuits with a suitable Earth Ground.
Power Cable Configuration
Cable
Pin
International
Screw Color
Brown
Live
L
Yellow or Brass
Blue
Neutral
N
Silver
Yellow/Green
Earth
EG (Ground)
Green
Mounting
Orientation
This fixture can be mounted on a truss using a clamp in any position or against a flat surface using
the brackets provided.
Rigging
The fixture includes a mounting yoke to which 1 rigging clamp can be bolted
and (2) Flush Mount Brackets for flush mounting to flat surfaces. You must
supply your own clamp and make sure the clamp is capable of supporting the
weight of this fixture. You can order C-clamps from any CHAUVET® dealer or
distributor.
1. Block access below the work area and use suitable and stable
platform when installing or servicing fixture.
2. Align the clamp screw with the center hole on the yoke and
tighten.
3. Verify the structure can hold 10 times the weight of all to-be
installed fixtures.
4. Adjust the angle on the yoke arm as necessary.
5. Always use a safety cable or chain as a secondary source of
attachment. The safety cable must hold 10 times the weight of the
fixture. If safety cable attachment point is provided that is
permanently affixed to the surface or body of the fixture, use that
instead of looping through a hanging yoke/arm.
Flush Mounting
1. Draw a screw hole template on a large piece of vellum or transparent paper for best alignment.
2. Place paper against the mounting surface and drill holes or mark the surface for drilling.
3. Hang panel.

Setup
LED Shadow User Manual Rev. 5 8
Fixture Linking
You will need a serial data link to run light shows of one or more fixtures using a DMX-512 controller
or to run synchronized shows on two or more fixtures set to a master/slave operating mode. The
combined number of channels required by all the fixtures on a serial data link determines the number
of fixtures the data link can support.
The LED Shadow fixtures use 3 channels of DMX control.
Important: Fixtures on a serial data link must be daisy chained in one single line. To
comply with the EIA-485 standard no more than 32 devices should be
connected on one data link. Connecting more than 32 fixtures on one serial
data link without the use of a DMX optically isolated splitter may result in
deterioration of the digital DMX signal.
Maximum recommended serial data link distance: 500 meters (1640 ft)
Maximum recommended number of fixtures on a serial data link: 32 fixtures
Data Cabling
To link fixtures together you must obtain data cables. You can purchase CHAUVET® certified DMX
cables directly from a dealer/distributor or construct your own cable. If you choose to create your own
cable please use data-grade cables that can carry a high quality signal and are less prone to
electromagnetic interference.
DMX Data Cable
Use a Belden© 9841 or equivalent cable which meets the specifications for EIA RS-485 applications.
Standard microphone cables cannot transmit DMX data reliably over long distances. The cable will
have the following characteristics:
•2-conductor twisted pair plus a shield
•Maximum capacitance between conductors – 30 pF/ft
•Maximum capacitance between conductor and shield – 55 pF/ft
•Maximum resistance of 20Ω/ 1000 ft
•Nominal impedance 100–140Ω
Cable Connectors
Cabling must have a male XLR connector on one end and a female XLR connector on the other end.
CAUTION Do not allow contact between the common and the fixture’s chassis ground.
Grounding the common can cause a ground loop and your fixture to perform
erratically. Test cables with OHM meter to verify correct polarity and to make
sure the pins are not grounded or shorted to the shield or each other.
COMMON
DMX +
DMX -
INPUT
OUTPUT
1
3
2
1
3
2
1
3
2
Resistance 120
ohm 1/4w between
pin 2 (DMX -) and
pin 3 (DMX +) of
the last fixture.
Termination reduces signal errors and
to avoid signal transmission problems
and interference, it is always
advisable to connect a DMX signal
DMX connector configuration

Setup
LED Shadow User Manual Rev. 5 9
This drawing provides a
general illustration of the
DMX input/output panel
of a lighting fixture.
Universal DMX Controller
Continue the link
Often, the setup for Master-Slave
and Standalone operation
requires that the first fixture in
the chain be initialized for this
purpose via either settings in the
control panel or DIP-switches.
Secondarily the fixtures that
follow may also require a slave
setting. Please consult the
“Operating Instructions” section
in this manual for complete
instructions for this type of setup
and configuration.
Fixtures displayed are for illustration purpose only!
3-Pin to 5-Pin Conversion Chart
Note! If you use a controller with a 5-pin DMX output connector, you will need to use
a 5-pin to 3-pin adapter. CHAUVET® Model No: DMX5M.
The chart below details a proper cable conversion:
3-pin to 5-pin Conversion Chart
Conductor
3-pin Female (output)
5-pin Male (Input)
Ground/Shield
Pin 1
Pin 1
Data ( - )signal
Pin 2
Pin 2
Data ( + ) signal
Pin 3
Pin 3
Do not use
Do not use
Do not use
Do not use
Setting up a DMX Serial Data Link
1. Connect the (male) 3-pin connector side of
the DMX cable to the output (female) 3-pin
connector of the controller.
2. Connect the end of the cable coming from
the controller which will have a (female)
3-pin connector to the input connector of
the next fixture consisting of a (male) 3-pin
connector.
3. Then, proceed to connect from the output
as stated above to the input of the following
fixture and so on.
CHAUVET® Certified DMX Data Cables
Order Code Description
DMX1.5 DMX Cable 1.5 m/4.9 ft
DMX4.5 DMX Cable 4.5 m/14.8 ft
DMX10 DMX Cable 10 m/32.8 ft
Standalone/Master-Slave Fixture Linking
1. Connect the (male) 3-pin connector side of the DMX cable to the output (female) 3-pin connector
of the first fixture.
2. Connect the end of the cable coming from the first fixture which will have a (female) 3-pin
connector to the input connector of the next fixture consisting of a (male) 3-pin connector. Then,
proceed to connect from the output as stated above to the input of the following fixture and so on.

LED Shadow™ User Manual Rev. 5 10
1
2
3
4
5
6
7
8
9
10
1 2 4 8
16 32 64
128 256
Option
Sound
Auto
ON
4. Operating Instructions
The LED Shadow is a DMX-512 controllable, flash UV LED panel made up of highly efficient and
super bright UV LEDs. The LED Shadow can operate in Stand-Alone, Master/Slave and via DMX-512
control utilizing 3 channels.
Standalone Mode
The LED Shadow can be operated without a DMX controller
in a standalone mode. It can be operated as a single fixture
or together with several other LED Shadow fixtures in
what is called a “Master/Slave” configuration.
Single-Fixture Mode
The LED Shadow can be set to operate independently of other fixtures or a DMX controller in either a
sound-active or automatic mode. A serial data-link is not necessary for this mode of operation and it
is recommended that no connection to other fixtures be made at all.
1. Simply choose from any one of 10 built-in “DIP-switch Options” from the table below.
Master-Slave Mode
A master-slave mode setup consists of more than one fixture connected in a serial data link without
the use of a controller. In a master-slave operation the slave fixtures will synchronize and will behave
either identically or in a planned chase pattern to the master unit which must be the first in the serial
daisy chain. A Master-Slave LED Shadow system can consist of an unlimited range of fixtures or at
least the number stated to conform to EIA-485 standards.
Setup
1. The LED Shadow sets up automatically for Master-Slave, no DIP-switch settings are required
other than for selecting DIP-switch Options.
2. Connect the end of the cable coming from the first fixture which will have a (female) 3-pin
connector to the DMX IN input connector of the Slave fixture consisting of a (male) 3-pin
connector. Continue the loop from DMX OUT to DMX IN.
Dipswitch Options
Functions
Dipswitches ( ON )
Notes & Description
Full On
None
All LEDs on
Flash
1
Flash Speed 1
2
Flash Speed 2
3
Flash Speed 3
4
Flash Speed 4
5
Flash Speed 5
6
Flash Speed 6
7
Flash Speed 7
8
Flash Speed 8
Sound-Active 9
All LEDs off until triggered by sound. Audio sensitivity rotary
knob sets sound sensitivity
Preset
Program
10 Preset Programs run in Automatic speed

Operating Instructions
LED Shadow User Manual Rev. 5 11
DMX Control Mode
The LED Shadow can be operated from a DMX controller. This control mode environment gives the
user the greatest flexibility when it comes to customizing or creating a show by enabling the control of
each individual trait of the fixture and each fixture independently.
Configuring for DMX control
1. Connect the (male) 3-pin connector side of the DMX cable to the output (female) 3-pin connector
of the controller.
2. Connect the end of the cable coming from the controller which will have a (female) 3-pin connector
to the input connector of the next fixture consisting of a (male) 3-pin connector.
3. Then, proceed to connect from the DMX output as stated above to the DMX input of the following
fixture and so on.
4. If you need help setting the DMX address read the section titled “Setting the DMX address” in this
Chapter.
Setting the DMX address
Each fixture requires a "start address" from 1 to 511. A fixture requiring one or more channels for
control begins to read the data on the channel indicated by the start address. For example, a fixture
that occupies or uses 7 channels of DMX and was addressed to start on DMX channel 100, would
read data from channels: 100, 101, 102, 103, 104, 105 and 106. Choose start addresses so that the
channels used do not overlap and notate the start address selected for future reference. If this is
your first time, read the DMX Primer in the Appendix Section.
Daisy Chain (Serial Data Link)
DMX Input
Use certified DMX XLR cable
DMX Output
DMX:001
DMX:004
DMX:007
1
2
3
4
5
6
7
8
9
10
1
2
3
4
5
6
7
8
9
10
1
2
3
4
5
6
7
8
9
10
Visit the section titled; Binary & DMX DIP-switch Addressing on page 13 & Binary Addressing Quick
Reference Chart
on page 14 to quickly determine the binary DIP-switch settings for addressing.

LED Shadow™ User Manual Rev. 5 12
5.Appendix
DMX Primer
There are 512 channels in a DMX-512 connection. Channels may be assigned in any manner. A
fixture capable of receiving DMX-512 will require one or a number of sequential channels. The user
must assign a starting address on the fixture that indicates the first channel reserved in the controller.
There are many different types of DMX controllable fixtures and they all may vary in the total number
of channels required. Choosing a start address should be planned in advance. Channels should
never overlap. If they do, this will result in erratic operation of the fixtures whose starting address is
set incorrectly. You can however, control multiple fixtures of the same type using the same starting
address as long as the intended result is that of unison movement or operation. In other words, the
fixtures will be slaved together and all respond exactly the same.
DMX fixtures are designed to receive data through a serial Daisy Chain. A Daisy Chain connection is
where the DATA OUT of one fixture connects to the DATA IN of the next fixture. The order in which
the fixtures are connected is not important and has no effect on how a controller communicates to
each fixture. Use an order that provides for the easiest and most direct cabling. Connect fixtures
using shielded two conductor twisted pair cable with three pin XLR male to female connectors. The
shield connection is pin 1, while pin 2 is Data Negative (S-) and pin 3 is Data positive (S+).
CHAUVET® carries 3-pin XLR DMX compliant cables, DMX-10 (33’), DMX-4.5 (15’) and DMX-1.5 (5’)
Returns Procedure
Returned merchandise must be sent prepaid and in the original packing, call tags will not be issued.
Package must be clearly labeled with a Return Merchandise Authorization Number (RA #). Products
returned without an RA # will be refused. Call CHAUVET® and request RA # prior to shipping the
fixture. Be prepared to provide the model number, serial number and a brief description of the cause
for the return. Be sure to properly pack fixture, any shipping damage resulting from inadequate
packaging is the customer’s responsibility. CHAUVET® reserves the right to use its own discretion to
repair or replace product(s). As a suggestion, proper UPS packing or double-boxing is always a safe
method to use.
Claims
Damage incurred in shipping is the responsibility of the shipper; therefore the damage must be
reported to the carrier upon receipt of merchandise. It is the customer's responsibility to notify and
submit claims with the shipper in the event that a fixture is damaged due to shipping. Any other claim
for items such as missing component/part, damage not related to shipping, and concealed damage,
must be made within seven (7) days of receiving merchandise.
Maintenance
To maintain optimum performance and minimize wear, fixtures should be cleaned frequently. Usage
and environment are contributing factors in determining frequency. As a general rule, fixtures should
be cleaned at least twice a month. Dust build up reduces light output performance and can cause
overheating. This can lead to reduced lamp life and increased mechanical wear. Be sure to power off
fixture before conducting maintenance.

Appendix
LED Shadow User Manual Rev. 5 13
Unplug fixture from power. Use a vacuum or air compressor and a soft brush to remove dust
collected on external vents and internal components. Clean all glass when the fixture is cold with a
mild solution of glass cleaner or Isopropyl Alcohol and a soft lint free cotton cloth or lens tissue. Apply
solution to the cloth or tissue and drag dirt and grime to the outside of the lens. Gently polish optical
surfaces until they are free of haze and lint. Do not to touch the lamp glass when cleaning fixture. Oil
and dirt can cause damage and premature aging of the lamp. In the event that the lamp is touched or
becomes dirty, clean the lamps with an alcohol wipe.
The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to
optimize light output. Cleaning frequency depends on the environment in which the fixture operates:
damp, smoky or particularly dirty surrounding can cause greater accumulation of dirt on the unit’s
optics. Clean with soft cloth using normal glass cleaning fluid. - Always dry the parts carefully. - Clean
the external optics at least every 20 days. Clean the internal optics at least every 30/60 days.
Binary & DMX DIP-switch Addressing
Each DIP-switch has an associated value. Adding the value of each switch in the ON position will
provide the final address. Determining which switches to toggle ON given a specific desired address
or value can be accomplished in the following manner. By subtracting the largest switch value
possible from the selected start address which does not cause a negative number.
Alternatively, using the “Binary Addressing Quick Reference Chart” in the Appendix section of this
manual, you can go directly to DIP-switch settings associated with all 512 values available.
EXAMPLE ADDRESS
Address 10
Pin # 4 = 8
Pin # 2 = 2
Total = 10
Address 24
Pin # 5 = 16
Pin # 4 = 8
Total = 24
Resolving address
using simple math.
Address 233
233 – (128) = 105, Turn ON Dip # 8
105 – (64) = 41, Turn ON Dip # 7
41 – (32) = 9, Turn ON Dip # 6
9 – (8) = 1, Turn ON Dip # 4
1 – (1) = 0, Turn ON Dip # 1
You will most likely use the first available
number which maybe number 1. This
number was selected for tutorial
purposes.
D
IP
S
WITCH
(DMX
V
ALUE
)
1
2
3
4
5
6
7
8
9
10
1
2
4
8
16
32
64
128
256
1
2
3
4
5
6
7
8
9
10
1 2 4 8
16 32 64
128 256
ON
1
2
3
4
5
6
7
8
9
10
1 2 4 8
16 32 64
128 256
ON

Appendix
LED Shadow User Manual Rev. 5 14
Binary Addressing Quick Reference Chart
DMX & Binary Address Quick Reference Chart
DIP-switch Position
DMX DIP-SWITCH SET
#9
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0=OFF
#8
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
1=ON
#7
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
X=OFF or ON
#6
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
#1
#2
#3
#4
#5
0
0
0
0
0
32
64
96
128
160
192
224
256
288
320
352
384
416
448
480
1
0
0
0
0
1
33
65
97
129
161
193
225
257
289
321
353
385
417
449
481
0
1
0
0
0
2
34
66
98
130
162
194
226
258
290
322
354
386
418
450
482
1
1
0
0
0
3
35
67
99
131
163
195
227
259
291
323
355
387
419
451
483
0
0
1
0
0
4
36
68
100
132
164
196
228
260
292
324
356
388
420
452
484
1
0
1
0
0
5
37
69
101
133
165
197
229
261
293
325
357
389
421
453
485
0
1
1
0
0
6
38
70
102
134
166
198
230
262
294
326
358
390
422
454
486
1
1
1
0
0
7
39
71
103
135
167
199
231
263
295
327
359
391
423
455
487
0
0
0
1
0
8
40
72
104
136
168
200
232
264
296
328
360
392
424
456
488
1
0
0
1
0
9
41
73
105
137
169
201
233
265
297
329
361
393
425
457
489
0
1
0
1
0
10
42
74
106
138
170
202
234
266
298
330
362
394
426
458
490
1
1
0
1
0
11
43
75
107
139
171
203
235
267
299
331
363
395
427
459
491
0
0
1
1
0
12
44
76
108
140
172
204
236
268
300
332
364
396
428
460
492
1
0
1
1
0
13
45
77
109
141
173
205
237
269
301
333
365
397
429
461
493
0
1
1
1
0
14
46
78
110
142
174
206
238
270
302
334
366
398
430
462
494
1
1
1
1
0
15
47
79
111
143
175
207
239
271
303
335
367
399
431
463
495
0
0
0
0
1
16
48
80
112
144
176
208
240
272
304
336
368
400
432
464
496
1
0
0
0
1
17
49
81
113
145
177
209
241
273
305
337
369
401
433
465
497
0
1
0
0
1
18
50
82
114
146
178
210
242
274
306
338
370
402
434
466
498
1
1
0
0
1
19
51
83
115
147
179
211
243
275
307
339
371
403
435
467
499
0
0
1
0
1
20
52
84
116
148
180
212
244
276
308
340
372
404
436
468
500
1
0
1
0
1
21
53
85
117
149
181
213
245
277
309
341
373
405
437
469
501
0
1
1
0
1
22
54
86
118
150
182
214
246
278
310
342
374
406
438
470
502
1
1
1
0
1
23
55
87
119
151
183
215
247
279
311
343
375
407
439
471
503
0
0
0
1
1
24
56
88
120
152
184
216
248
280
312
344
376
408
440
472
504
1
0
0
1
1
25
57
89
121
153
185
217
249
281
313
345
377
409
441
473
505
0
1
0
1
1
26
58
90
122
154
186
218
250
282
314
346
378
410
442
474
506
1
1
0
1
1
27
59
91
123
155
187
219
251
283
315
347
379
411
443
475
507
0
0
1
1
1
28
60
92
124
156
188
220
252
284
316
348
380
412
444
476
508
1
0
1
1
1
29
61
93
125
157
189
221
253
285
317
349
381
413
445
477
509
0
1
1
1
1
30
62
94
126
158
190
222
254
286
318
350
382
414
446
478
510
1
1
1
1
1
31
63
95
127
159
191
223
255
287
319
351
383
415
447
479
511
DIP
-switch Position DMX Address

Appendix
LED Shadow User Manual Rev. 5 15
DMX Channel Values
NOTE!
Please read all instructions carefully on fixture DMX control mode and addressing.
DMX channels 2, and 3 functions are determined by the current settings of channel 1. For example,
while Channel 1 is set between 000 and 029 the following conditions will apply;
§Channel 2 will control Dimming Intensity from 0 to 100%
§Channel 3 will control Dimming Intensity from 100% to 0
Channel
Value
Function
Ch 2
Ch 3
1
000 ó039 Dimmer Mode
Flash Speed
0
ó
100%
Intensity
100%ó0
040 ó159
Auto Mode 1
Speed
Slow óFast
160 ó199
Auto Mode 2
200 ó239
Auto Mode 3
240 ó255
Sound Mode
No Function
Technical Specifications
WEIGHT & DIMENSIONS
Length........................................................................................................................356 mm (14.0 in)
Width............................................................................................................................248 mm (9.8 in)
Height ..........................................................................................................................165 mm (6.5 in)
Weight.............................................................................................................................2.2 kg (4.9 lb)
POWER
Input Voltage................................................................................................100 to 240 VAC, 50/60 Hz
Power and Current.................................................................................... 12 W, 0.1 A @120 V, 60 Hz
Power and Current................................................................................... 11 W, 0.1 A @ 230 V, 50 Hz
FUSE
Type and Rating................................................................................................................F 1 A, 250 V
LED
Quantity ................................................................................................................................. 192 (UV)
Wavelength...............................................................................................................................405 nm
CONTROL & PROGRAMMING
Data input .........................................................................................................3-pin XLR male socket
Data output ....................................................................................................3-pin XLR female socket
Data pin configuration ............................................................................pin 1 shield, pin 2 (-), pin 3 (+)
Protocols.....................................................................................................................DMX-512 USITT
DMX Channels....................................................................................................................................3
ORDERING INFORMATION
LED Shadow™ ...................................................................................................Item Code: 02030287

Appendix
LED Shadow User Manual Rev. 5 16
R
ETURNS
To return a product or request support:
•In the U.S., contact CHAUVET® World Headquarters (see below).
•In the UK or Ireland, contact CHAUVET® Europe Ltd. (see below).
•In Mexico, contact CHAUVET® Mexico (see below).
•In any other country, DO NOT contact CHAUVET®. Contact the distributor of record. See
www.chauvetlighting.com for a list of distributors.
If you live outside the U.S., United Kingdom, Ireland, or Mexico, contact your distributor
of record and follow their instructions on how to return CHAUVET® products to them.
Visit our website for contact details.
U.S., UK, Ireland,
and Mexico
Call the corresponding CHAUVET® Technical Support office and request a Return
Merchandise Authorization (RMA) number before shipping the product. Be prepared to
provide the model number, serial number, and a brief description of the reason for the return.
You must send the merch
andise prepaid, in its original box, and with its original packing and
accessories. CHAUVET® will not issue call tags.
Clearly label the package with the RMA number. CHAUVET® will refuse any product returned
without an RMA number.
Write the RMA number
on a properly affixed label. DO NOT write the RMA number
directly on the box.
Before sending the product, clearly write the following information on a piece of paper and
place it inside the box:
Your name Your address Your phone number
RMA number A brief description of the problem
Be sure to pack the product properly. FedEx packing or double-boxing are recommended.
CHAUVET® reserves the right to use its own discretion to repair or replace returned
product(s). CHAUVET® is not responsible for shipping damage of returned items.
CONTACT
U
S
WORLD HEADQUARTERS - CHAUVET®
General Information
Address:5200 NW 108th Avenue
Sunrise, FL 33351
Voice: [phone]
Fax: [phone]
Toll free:[phone]
Technical Support
Voice: [phone] (Press 4)
Fax: [phone]
Email: [e-mail]
World Wide Web
www.chauvetlighting.com
UNITED KINGDOM AND IRELAND - CHAUVET® Europe Ltd.
General Information
Address:Unit 1C
Brookhill Road Industrial
Estate
Pinxton, Nottingham, UK
NG16 6NT
Voice: [phone]
Fax: [phone]
Technical Support
Email: [e-mail]
World Wide Web
www.chauvetlighting.co.uk
MEXICO - CHAUVET® Mexico
General Information
Address:Av. Santa Ana 30
Parque Industrial Lerma
Lerma, Mexico C.P. 52000
Voice: [phone]
Technical Support
Email: [e-mail]
World Wide Web
www.chauvet.com.mx
Outside the U.S., United Kingdom, Ireland, or Mexico, contact the dealer of record and follow
their instructions to request support or to return a product. Visit the CHAUVET
®
website for
contact information.