Chauvet M-Mover User manual

Snapshot
Ok on Dimmer
Outdoor OK
Sound Activated
DMX512
Master/Slave
115V/230V Switch
Replaceable Fuse
User Serviceable
Duty Cycle
M-MOVER
Multi Mover™
USER MANUAL
Chauvet, 3000 N 29th Ct, Hollywood, FL 33020 U.S.A.
[phone] – [phone]
FAX [phone]
www.chauvetlighting.com

TABLE OF CONTENTS
1. BEFORE YOU BEGIN................................................................................................................................3
WHAT IS INCLUDED......................................................................................................................................... 3
UNPACKING INSTRUCTIONS............................................................................................................................. 3
AC POWER ................................................................................................................................................... 3
CONTACT US................................................................................................................................................. 3
SAFETY INSTRUCTIONS................................................................................................................................... 4
2. INTRODUCTION ........................................................................................................................................ 5
FEATURES..................................................................................................................................................... 5
DMX CHANNEL SUMMARY.............................................................................................................................. 5
PRODUCT OVERVIEW ..................................................................................................................................... 6
3. SETUP........................................................................................................................................................ 7
PLATFORM PLATE MOUNTING.......................................................................................................................... 7
FUSE REPLACEMENT...................................................................................................................................... 7
FIXTURE LINKING ........................................................................................................................................... 7
Data Cabling ........................................................................................................................................... 7
DMX Data Cable............................................................................................................................... 8
Cable Connectors............................................................................................................................. 8
3-Pin to 5-Pin Conversion Chart....................................................................................................... 8
SETTING UP A DMX SERIAL DATA LINK............................................................................................................ 9
STAND-ALONE/MASTER/SLAVE FIXTURE LINKING.............................................................................................. 9
MOUNTING...................................................................................................................................................10
Orientation.......................................................................................................................................10
Rigging ............................................................................................................................................10
4. OPERATING INSTRUCTIONS..................................................................................................................10
NAVIGATING THE CONTROL PANEL .................................................................................................................10
MENU MAP...................................................................................................................................................11
Menu Functions .....................................................................................................................................12
User Configurations ...............................................................................................................................12
To set the pan to inverting or non-inverting: ....................................................................................12
To reverse the display: ....................................................................................................................12
Service Functions ..................................................................................................................................12
To turn the Platform Power on or off:...............................................................................................12
To reset the fixture:..........................................................................................................................12
To restore all settings to their factory defaults: ................................................................................12
OPERATION..................................................................................................................................................13
Stand-Alone Mode (Auto Mode):............................................................................................................13
Master/Slave Mode (Master Auto): ........................................................................................................13
DMX Mode.............................................................................................................................................14
DMX CHANNEL VALUES................................................................................................................................14
General Troubleshooting........................................................................................................................15
TECHNICAL SUPPORT....................................................................................................................................16
5. APPENDIX.................................................................................................................................................16
DMX PRIMER...............................................................................................................................................16
GENERAL MAINTENANCE ...............................................................................................................................17
RETURNS PROCEDURE..................................................................................................................................17
CLAIMS........................................................................................................................................................17
TECHNICAL SPECIFICATIONS ..........................................................................................................................18
Multi Mover User Manual 2 2007-01-03/16:45

1. BEFORE YOU BEGIN
What is included
¾1 x Multi Mover™
¾Power Cord
¾Warranty Card
¾User Manual
Unpacking Instructions
Immediately upon receiving a fixture, carefully unpack the carton, check the contents to ensure that
all parts are present, and have been received in good condition. Notify the shipper immediately and
retain packing material for inspection if any parts appear damaged from shipping or the carton itself
shows signs of mishandling. Save the carton and all packing materials. In the event that a fixture
must be returned to the factory, it is important that the fixture be returned in the original factory box
and packing.
AC Power
Figure 1 - AC Voltage Switch
Not all fixtures have a voltage
select switch. Please be sure to
connect to the proper voltage.
To determine the power requirements for a particular fixture, see the label affixed to the back plate of
the fixture or refer to the fixture’s specifications chart. A fixture’s listed current rating is its average
current draw under normal conditions. All fixtures must be powered directly off a switched circuit and
cannot be run off a rheostat (variable resistor) or dimmer circuit, even if the rheostat or dimmer
channel is used solely for a 0% to 100% switch. Before applying power to a
fixture, check that the source voltage matches the fixture’s requirement.
Check the fixture or device carefully to make sure that if a voltage selection
switch exists that it is set to the correct line voltage you will use.
Warning! Verify that the voltage select switch on your unit matches the
line voltage applied. Damage to your fixture may result if the
line voltage applied does not match the voltage indicated on
the voltage selector switch. All fixtures must be connected to
circuits with a suitable Earth Ground.
Contact Us
World Wide
General Information Chauvet Lighting
3000 North 29th Court
Hollywood, FL 33020
voice: 954.929.1115
fax: [phone]
toll free: 800.762.1084
Technical Support Chauvet Lighting
3000 North 29th Court
Hollywood, FL 33020
voice: 954.929.1115 (Press 4)
fax: [phone] (Attention: Service)
World Wide Web www.chauvetlighting.com
Multi Mover User Manual 3 2007-01-03/16:45

Safety Instructions
Please read these instructions carefully, which includes important
information about the installation, usage and maintenance of this
product.
•Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that
they also receive this instruction booklet.
•Always make sure that you are connecting to the proper voltage, and that the line voltage you are
connecting to is not higher than that stated on the decal or rear panel of the fixture.
•This product is intended for indoor use only!
•To prevent risk of fire or shock, do not expose fixture to rain or moisture. Make sure there are no
flammable materials close to the unit while operating.
•The unit must be installed in a location with adequate ventilation, at least 20in (50cm) from adjacent
surfaces. Be sure that no ventilation slots are blocked.
•Always disconnect from power source before servicing or replacing lamp or fuse and be sure to
replace with same lamp source.
•Secure fixture to fastening device using a safety chain. Never carry the fixture solely by its head. Use
its carrying handles.
•Maximum ambient temperature (Ta) is 104°F (40°C). Do not operate fixture at temperatures higher
than this.
•In the event of a serious operating problem, stop using the unit immediately. Never try to repair the
unit by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please
contact the nearest authorized technical assistance center. Always use the same type spare parts.
•Don’t connect the device to a dimmer pack.
•Make sure the power cord is never crimped or damaged.
•Never disconnect the power cord by pulling or tugging on the cord.
Caution! There are no user serviceable parts inside the unit. Do not open the housing or
attempt any repairs yourself. In the unlikely event your unit may require service,
please contact CHAUVET at: 954-929-1115.
Multi Mover User Manual 4 2007-01-03/16:45

2. INTRODUCTION
Features
•4-channel DMX-512 media mover
•Pan: 540° (ultra smooth)
•Vector speed, power on/off and reset channel
Additional Features
•3-pin and 5-pin DMX connections on base and platform
•5 RCA in/out connections capable of up to a 720p signal (individually grounded)
•1 XLR in/out connection
•DMX pass-through to platform when power is on/off
•IEC and Edison power connectors on platform
•Convenient ¼”-turn fasteners
•Multiple mounting options:
Platform plate with mounting slots
Dual mounting brackets
•Built-in automatic programs via master/slave
•Automatic pan correction
•Micro-stepping motors
•LED display
•16bit pan resolution
•Isolated fuses for base and platform
•Fan cooled
DMX Channel Summary
CHANNEL FUNCTION
1 Pan
2 Fine Pan
3 Vector Speed
4 Platform Power
Multi Mover User Manual 5 2007-01-03/16:45

Product Overview
¼ Turn
Fasteners
Base
Control
Panel
Platform
XLR In/Out
Connector
IEC Power Out
Connector
RCA In/Out
Connectors
XLR In/Out
RCA In/Out
connectors
DMX Input
Connector
5-pin DMX Input
Connector
Base Front
5-pin DMX
Output
Connector
5-pin DMX
Output
Connecto
r
Edison Power
Out Connector
Voltage
Selector
Switch
Base Bac
k
AC Power
Switch
IEC Power
Connector
Platform
Fuse
Base
Fuse
Platform Front
DMX Output
Connector
Platform Bac
k
DMX Output
Connector
Multi Mover User Manual 6 2007-01-03/16:45

3. SETUP
Platform Plate Mounting
You may mount many different items to the Multi Mover ™ using the included platform and brackets.
Fuse Replacement
Disconnect the power cord before replacing a fuse and always
replace with the same type fuse.
With a flat-head screwdriver, unscrew the fuse
holder from its housing. Remove the damaged
fuse from its holder and replace with exact
same type fuse. Screw the fuse holder back in
its place and reconnect power.
The fuse is located
inside this
compartment.
Remove using a flat
head screwdriver. FUSE
Fixture Linking
You will need a serial data link to run light shows of one or more fixtures using a DMX-512 controller
or to run synchronized shows on two or more fixtures set to a master/slave operating mode. The
combined number of channels required by all the fixtures on a serial data link determines the number
of fixtures the data link can support.
Important: Fixtures on a serial data link must be daisy chained in one single line. To comply with the EIA-485
standard no more than 32 devices should be connected on one data link. Connecting more than 32
fixtures on one serial data link without the use of a DMX optically-isolated splitter may result in
deterioration of the digital DMX signal.
Maximum recommended serial data link distance: 500 meters (1640 ft.)
Maximum recommended number of fixtures on a serial data link: 32 fixtures
Data Cabling
To link fixtures together you must obtain data cables. You can purchase CHAUVET-certified DMX
cables directly from a dealer/distributor or construct your own cable. If you choose to create your own
cable please use data-grade cables that can carry a high quality signal and are less prone to
electromagnetic interference.
Multi Mover User Manual 7 2007-01-03/16:45

DMX DATA CABLE
Use a Belden© 9841 or equivalent cable which meets the specifications for EIA RS-485 applications.
Standard microphone cables cannot transmit DMX data reliably over long distances. The cable will
have the following characteristics:
2-conductor twisted pair plus a shield
Maximum capacitance between conductors – 30 pF/ft.
Maximum capacitance between conductor and shield – 55 pF/ft.
Maximum resistance of 20 ohms / 1000 ft.
Nominal impedance 100 – 140 ohms
CABLE CONNECTORS
Cabling must have a male XLR connector on one end and a female XLR connector on the other end.
can cause a ground loop, and your fixture may perform erratically. Test cables with an ohm meter to r.
3-PIN TO 5-PIN CONVE
pin DMX output connector, you will need to use a 5 pin to 3 pin adapter.
CHAUVET Model No: DMX5M, or DMX5F.
3PIN TO 5PIN C
Conductor 3 Pin Female (output) 5 Pin Male (Input)
CO
MM
O
N
DMX
+
DMX -
INPUT OUTPUT
1
3
2
1
3
2
1
3
2
Resistance 120
ohm 1/4w between
pin 2 (DMX -) and
pin 3 (DMX +) of
the last fixture.
Termination reduces signal errors and
to avoid signal transmission problems
and interference, it is always
advisable to connect a DMX signal
terminator.
DMX connector configuration
CAUTION Do not allow contact between the common and the fixture’s chassis ground. Grounding the common
verify correct polarity and to make sure the pins are not grounded or shorted to the shield or each othe
RSION CHART
Note! If you use a controller with a 5
The chart below details a proper cable conversion:
ONVERSION CHART
Grou hieldnd/S Pin 1 Pin 1
Data ( - ) signal Pin 2 Pin 2
Data ( + ) signal Pin 3 Pin 3
Do not use Do not use
Do not use Do not use
Multi Mover User Manual 8 2007-01-03/16:45

This drawing provides a
general illustration of the
DMX Input/Output panel of
a lighting fixture.
Universal DMX Controller
Continue the link
Setting up a DMX Serial Data Link
1. Connect the (male) 3 pin connector side of
the DMX cable to the output (female) 3 pin
connector of the controller.
2. Connect the end of the cable coming from
the controller which will have a (female) 3
pin connector to the input connector of the
next fixture consisting of a (male) 3 pin
connector.
3. Then, proceed to connect from the output
as stated above to the input of the following
fixture and so on.
CHAUVET Certified DMX Data Cables
Order Code Description
DMX1.5 DMX Cable 1.5m/4.9ft
DMX4.5 DMX Cable 4.5m/14.8ft
DMX10 DMX Cable 10m/32.8ft
Stand-Alone/Master/Slave Fixture Linking
1. Connect the (male) 3 pin connector side of the DMX cable to the output (female) 3 pin connector
of the first fixture.
2. Connect the end of the cable coming from the first fixture which will have a (female) 3 pin
connector to the input connector of the next fixture consisting of a (male) 3 pin connector. Then,
proceed to connect from the output as stated above to the input of the following fixture and so on.
Often, the setup for Master-Slave
and Standalone operation requires
that the first fixture in the chain be
initialized for this purpose via either
settings in the control panel or DIP-
switches. Secondarily, the fixtures
that follow may also require a slave
setting. Please consult the
“Operating Instructions” section in
this manual for complete instructions
for this type of setup and
configuration.
Multi Mover User Manual 9 2007-01-03/16:45

Mounting
ORIENTATION
This fixture must be mounted horizontally. The base may be set on a flat surface or suspended.
However, the base must always be parallel to the floor.
Floor
RIGGING
Hanging Clamp
It is important never to obstruct the fan or vents pathway. Mount the
fixture using, a suitable “C” or “O” type clamp. Adjust the angle of
the fixture by loosening both knobs and tilting the fixture. After
finding the desired position, retighten both knobs.
•When selecting installation location, take into consideration lamp
replacement access and routine maintenance.
•Safety cables should always be used. Note!
Clamp is sold separatel
•Never mount in places where the fixture will be exposed to rain, high
humidity, extreme temperature changes or restricted ventilation.
y
.
•Always use heavy duty hanging clamps with this fixture.
4. OPERATING INSTRUCTIONS
Navigating the Control Panel
Access control panel functions using the four panel buttons located directly underneath the LCD
Display. NOTE: The display will turn off after 30 seconds if no buttons are pushed.
MODE
/ESC
Button Function UP
DOWN
ENTER
CONTROL PANEL
<MODE/ESC> Used to access the menu or to scroll
through top-level menu items.
<UP> Scrolls through menu options in ascending
order
<DOWN> Scrolls through menu options in descending
order
<ENTER> Used to select and store the current menu
or option within a menu DMX Signal Indicator
Multi Mover User Manual 10 2007-01-03/16:45

The Control Panel LED Display shows the menu items you select from the menu map on page 13.
When a menu function is selected, the display will show immediately the first available option for the
selected menu function. To select a menu item, press <ENTER>.
Press the <MODE/ESC> button once to activate the control panel. Pressing the <MODE/ESC> button
again will scroll through the different top-level menu options available. Use the <UP> and <DOWN>
buttons to navigate the menu options. Press the <ENTER> button to access the menu function
currently displayed or to enable a menu option. To return to the previous option or menu without
changing the value, press the <MODE/ESC> button.
Menu Map
Multi Mover User Manual 11 2007-01-03/16:45

Menu Functions
MENU OPTION DESCRIPTION
Stand Alone – Automatic: The built in programs will trigger automatically to a pre-
programmed speed time.
Slave Unit: Sets the fixture to run in sync with the Master. You must set the first
fixture in the data link to “Master” otherwise nothing will happen.
DMX: The fixture will be controlled by a DMX signal coming from a DMX controller.
The starting address must be selected, and can be set using the up and down
buttons.
User Configurations
TO SET THE PAN TO INVERTING OR NON-INVERTING:
1) Press <MODE/ESC> until is displayed. Use the <UP> and <DOWN> buttons to
scroll through the two options. is non-inverting; is inverting.
TO REVERSE THE DISPLAY:
1) Press <MODE/ESC> until or is displayed.
2) Use the <UP> and <DOWN> buttons to scroll through the two options. is normal;
is reversed.
Service Functions
TO TURN THE PLATFORM POWER ON OR OFF:
1) Press the <MODE/ESC> button until or is displayed.
2) Use the <UP> and <DOWN> buttons to select the desired option and then press the <ENTER>
button. turns the platform power on; turns the platform power off.
TO RESET THE FIXTURE:
1) Press the <MODE/ESC> button until is displayed, and then press the <ENTER>
button. The fixture will now reset itself.
TO RESTORE ALL SETTINGS TO THEIR FACTORY DEFAULTS:
1) Press the <MODE/ESC> button until is displayed, and then press the <ENTER>
button. The fixture will now load all factory default settings.
Multi Mover User Manual 12 2007-01-03/16:45

Operation
Stand-Alone Mode (Auto Mode):
This mode allows a single unit to run to the beat of the music, or the unit will auto change in Auto
Mode.
1) Press <MODE/ESC> until , or is displayed.
2) Use the <UP> and <DOWN> buttons to scroll through until the is displayed and
press the <ENTER> button. will be displayed.
3) The unit will auto rotate in Auto Mode.
Master/Slave Mode (Master Auto):
This mode will allow you to link up to 32 units together without a controller.
1) Use standard DMX cables to daisy chain your units together via the DMX connector on the rear
of the units. For longer cable runs we suggest a terminator at the last fixture. For more
information about terminators, see page 8.
2) Choose a unit to function as the master. Press <MODE/ESC> until or
is displayed on the master unit.
3) Use the <UP> and <DOWN> buttons to scroll through until is displayed and
press the <ENTER> button. will be displayed.
4) Press <MODE/ESC> until or is displayed on the slave units. Use
the <UP> and <DOWN> buttons to scroll through until is displayed and press the
<ENTER> button. will be displayed
Multi Mover User Manual 13 2007-01-03/16:45

DMX Mode
This mode allows the unit to be controlled by any universal DMX controller. If you are unfamiliar with
DMX, please read the DMX Primer on page #.
1) Press <MODE/ESC> until is displayed.
2) Use the <UP> and <DOWN> buttons to select the desired address and press the <ENTER>
button.
DMX Channel Values
CHANNEL VALUE FUNCTION
1 000 Ù255
Pan
0 – 540°
128 = halfway point
2 000 Ù255 Fine Pan
3
000 Ù255 Vector Speed Normal > Slow
4
000 Ù129
130 Ù139
140 Ù209
210 Ù219
220 Ù229
230 Ù239
240 Ù255
Control/Service
No function
Pan movement reset
No function
Platform power on
No function
Platform power off
No function
Multi Mover User Manual 14 2007-01-03/16:45

General Troubleshooting Applies to
Symptom Solution(s)
Lights Foggers
& Snow Controllers Dimmers & Chaser
Auto shut off Check fan thermal switch reset 9
Beam is very dim or
not bright Clean optical system or replace lamp
Check 220/110v switch for proper setting 9
Breaker/Fuse keeps
blowing Check total load placed on device 9
Chase is too slow Check users manual for speed adjustment 999
Device has no power Check for power on Mains.
Check device’s fuse. (internal and/or external) 999
Fixture is not
responding Check DMX Dip switch settings for correct addressing Check DMX cables
Check polarity switch settings
9
Fixture is on but
there is no
movement to the
audio
Make sure you have the correct audio mode on the
control switches. If audio provided via ¼” jack, make
sure a live audio signal exists
Adjust sound sensitivity knob
999
Lamps cuts off
sporadically Possible bad lamp or fixture is overheating.
Lamp may be at end of its life. 9
Light will not come
on after power failure Some discharge lamps require a cooling off period before the electronics in the fixture can kick start it
again, wait 5 to 10 minutes before powering up
9
Loss of signal Use only DMX cables
Install terminator
Note: Keep DMX cables separated from power cables
or black lights.
9999
Moves slow Check 220/110v switch for proper setting 9
No flash Re-install bulb, may have shifted in shipping 9
No laser output Bounce mirror motor may have shifted during shipping,
readjust 9
No light output Check slip ring & brushes for contact
Install bulb
Call service technician
9
Relay will not work Check reset switch
Check cable connections 9
Remote does not
work Make sure connector is firmly connected to device 99
Stand alone mode All Chauvet lighting fixtures featuring stand-alone
functions do not require additional settings, simply
power the fixture and it will automatically enter into this
mode
9
If you still have a problem after trying the above solutions, please contact CHAUVET Technical
Support at the location on the next page.
Multi Mover User Manual 15 2007-01-03/16:45

Technical Support
Address: Service Dept.
3000 N 29th Ct, Hollywood, FL 33020 (U.S.A.)
Support (Email): [email protected]
Telephone: [phone] - (Press 4)
Fax: [phone] - (Attention: Service)
Website: http://www.chauvetlighting.com
5. APPENDIX
DMX Primer
There are 512 channels in a DMX-512 connection. Channels may be assigned in any manner. A
fixture capable of receiving DMX 512 will require one or a number of sequential channels. The user
must assign a starting address on the fixture that indicates the first channel reserved in the controller.
There are many different types of DMX controllable fixtures and they all may vary in the total number
of channels required. Choosing a start address should be planned in advance. Channels should
never overlap. If they do, this will result in erratic operation of the fixtures whose starting address is
set incorrectly. You can however, control multiple fixtures of the same type using the same starting
address as long as the intended result is that of unison movement or operation. In other words, the
fixtures will be slaved together and all respond exactly the same.
DMX fixtures are designed to receive data through a serial Daisy Chain. A Daisy Chain connection is
where the DATA OUT of one fixture connects to the DATA IN of the next fixture. The order in which
the fixtures are connected is not important and has no effect on how a controller communicates to
each fixture. Use an order that provides for the easiest and most direct cabling. Connect fixtures
using shielded two conductor twisted pair cable with three pin XLR male to female connectors. The
shield connection is pin 1, while pin 2 is Data Negative (S-) and pin 3 is Data positive (S+). CHAUVET
carries 3-pin XLR DMX compliant cables, DMX-10 (33’), DMX-4.5 (15’) and DMX-1.5 (5’)
Multi Mover User Manual 16 2007-01-03/16:45

General Maintenance
To maintain optimum performance and minimize wear fixtures should be cleaned frequently. Usage
and environment are contributing factors in determining frequency. As a general rule, fixtures should
be cleaned at least twice a month. Dust build up reduces light output performance and can cause
overheating. This can lead to reduced lamp life and increased mechanical wear. Be sure to power off
fixture before conducting maintenance.
Unplug fixture from power. Use a vacuum or air compressor and a soft brush to remove dust
collected on external vents and internal components. Clean all glass when the fixture is cold with a
mild solution of glass cleaner or Isopropyl Alcohol and a soft lint free cotton cloth or lens tissue. Apply
solution to the cloth or tissue and drag dirt and grime to the outside of the lens. Gently polish optical
surfaces until they are free of haze and lint.
The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to
optimize light output. Cleaning frequency depends on the environment in which the fixture operates:
damp, smoky or particularly dirty surrounding can cause greater accumulation of dirt on the unit’s
optics. Clean with soft cloth using normal glass cleaning fluid. - Always dry the parts carefully. - Clean
the external optics at least every 20 days. Clean the internal optics at least every 30/60 days.
Returns Procedure
Returned merchandise must be sent prepaid and in the original packing, call tags will not be issued.
Package must be clearly labeled with a Return Merchandise Authorization Number (RA #). Products
returned without an RA # will be refused. Call CHAUVET and request RA # prior to shipping the
fixture. Be prepared to provide the model number, serial number and a brief description of the cause
for the return. Be sure to properly pack fixture, any shipping damage resulting from inadequate
packaging is the customer’s responsibility. CHAUVET reserves the right to use its own discretion to
repair or replace product(s). As a suggestion, proper UPS packing or double-boxing is always a safe
method to use.
Note: If you are given an RA #, please include the following information on a piece of paper
inside the box:
1) Your name
2) Your address
3) Your phone number
4) The RA #
5) A brief description of the symptoms
Claims
Damage incurred in shipping is the responsibility of the shipper; therefore the damage must be
reported to the carrier upon receipt of merchandise. It is the customer's responsibility to notify and
submit claims with the shipper in the event that a fixture is damaged due to shipping. Any other claim
for items such as missing component/part, damage not related to shipping, and concealed damage,
must be made within seven (7) days of receiving merchandise.
Multi Mover User Manual 17 2007-01-03/16:45

Technical Specifications
WEIGHT & DIMENSIONS
Length........................................................................................................................... 17.5 in (445 mm)
Width ............................................................................................................................ 14.5 in (368 mm)
Height........................................................................................................................... 10.3 in (262 mm)
Weight ..........................................................................................................................37.2 lbs (16.9 kg)
POWER
Switch-selectable power settings..............................................................120V 60Hz AC or 230V 50Hz
Power Consumption..................................................................................................................24W Max
Inrush Power .................................................................................................................................... 36W
Power Output (AC Plug).............................................................. 1650W at 110V, 3450W at 230V Max
LOAD CAPACITY
Platform ...................................................................................................................110 lbs (50 kg) Max
ROTATION
Pan...................................................................................................................................................540°
THERMAL
Maximum ambient temperature...........................................................................................104°F (40°C)
FUSE
Main....................................................................................................20mm Glass 10A 250V Fast Blow
Platform..............................................................................................20mm Glass 15A 250V Fast Blow
CONTROL & PROGRAMMING
Data input..............................................locking 3-pin XLR male socket, locking 5-pin XLR male socket
Data output......................................locking 3-pin XLR female socket, locking 5-pin XLR female socket
Data pin configuration ..............................................................................pin 1 shield, pin 2 (-), pin 3 (+)
Protocols........................................................................................................................DMX-512 USITT
DMX Channels .......................................................................................................................................4
Bandwidth (-3dB)
RCA In/Out....................................................................................................... 85 MHz at Zin = 75 ohms
XLR In/Out........................................................................................................ 85 MHz at Zin = 75 ohms
ORDERING INFORMATION
Multi Mover............................................................................................................................. M-MOVER
WARRANTY INFORMATION
Warranty.............................................................................................................. 2-year limited warranty
Multi Mover User Manual 18 2007-01-03/16:45