Chauvet LFS-5 User manual

User Manual

Page 2 of 14 LFS-5 User Manual (Rev. 08)
TABLE OF CONTENTS
1. Before you Begin.................................................................................3
What is Included................................................................................................3
Unpacking Instructions......................................................................................3
Claims........................................................................................................................ 3
Text Conventions..............................................................................................3
Icons..................................................................................................................3
Document Information.......................................................................................3
Product at a Glance ..........................................................................................4
Safety Notes......................................................................................................4
2. Introduction..........................................................................................5
Product Overview..............................................................................................5
Product Dimensions..........................................................................................6
3. Setup.....................................................................................................7
AC Power..........................................................................................................7
Fuse Replacement..................................................................................................... 7
Power Linking............................................................................................................. 8
Mounting ...........................................................................................................9
Orientation ................................................................................................................. 9
Rigging....................................................................................................................... 9
4. Operation............................................................................................10
Power....................................................................................................................... 10
Framing Shutters...................................................................................................... 10
Focus and Zoom...................................................................................................... 10
Gobos ...................................................................................................................... 10
Color Gels................................................................................................................ 10
5. Technical Information........................................................................11
Product Maintenance......................................................................................11
General Troubleshooting ................................................................................12
Contact Procedure..........................................................................................13
CHAUVET® Contact Information....................................................................13
Returning Products to CHAUVET® ................................................................13
6. Technical Specifications...................................................................14

LFS-5 User Manual (Rev. 08) Page 3 of 14
1.BEFORE YOU BEGIN
What is
Included
1 x LFS-5
1 x Power Cord
4 x Metal Gobos
1 x Warranty Card
1 x Quick Reference Guide
Unpacking
Instructions
Immediately upon receipt, carefully unpack this product and check the container to make
sure you have received all the parts indicated above in good condition.
Claims If the container or the material inside the container (this product and any other accessory
included) appears damaged from shipping, or shows signs of mishandling, notify the
carrier immediately, not CHAUVET®, upon receipt of the damaged merchandise. Failure
to do so in a timely manner may invalidate your claim with the carrier. In addition, retain
the container and all the packing material for inspection.
For other issues such as missing components or parts, damage not related to shipping,
or concealed damage, file a claim with CHAUVET® within seven (7) days of receiving
the merchandise.
Text
Conventions
Convention Meaning
1~512 A range of values
50/60 A set of values of which only one can be chosen
Settings A menu option not to be modified
Menu > Settings A sequence of menu options to be followed
<ENTER> A key to be pressed on the product’s control panel
ON A value to be entered or selected
Icons Icon Meaning
This paragraph contains critical installation, configuration, or
operation information. Failure to comply with this information may
render the product partially or completely inoperative, cause
damage to the product, or cause harm to the user.
This paragraph contains important installation or configuration
information. Failure to comply with this information may prevent
the product from functioning correctly.
This paragraph reminds you of useful, although not critical,
information.
Document
Information
The information and specifications contained in this document are subject to change
without notice. CHAUVET® assumes no responsibility or liability for any errors or
omissions that may appear in this manual. CHAUVET® reserves the right to update the
existing document or to create a new document to correct any errors or omissions.
You can download the latest version of this document from www.chauvetlighting.com.
© Copyright 2011 CHAUVET®. All rights reserved
Electronically published by CHAUVET® in the United States of America
Author Editor Specialist Manager
A. Diaz B. Pillow R. Jones A. Reiss

Page 4 of 14 LFS-5 User Manual (Rev. 08)
Product at a
Glance
Use on Dimmer Auto Programs 
Outdoor Use Auto-ranging Power Supply 
Sound Activated Replaceable Fuse 
DMX User Serviceable 
Master/Slave Duty Cycle 
Safety Notes Please read the following Safety Notes carefully before working with this product. They
include important safety information about its installation, usage, and maintenance.
Always connect this product to a grounded circuit to avoid the risk of electrocution.
Always disconnect this product from the power source before cleaning it or replacing
the fuse.
Avoid direct eye exposure to the light source while the product is on.
Make sure the power cord is not crimped or damaged.
Never disconnect this product from power cord by pulling or tugging on the cord.
If mounting this product overhead, always secure it to a fastening device using a
safety cable.
Make sure there are no flammable materials close to the unit while operating.
Do not touch this product’s housing when operating because it may be very hot.
Always make sure that the voltage of the outlet to which you are connecting this
product is within the range stated on the decal or rear panel of the product.
This product is for indoor use only! (IP20) To prevent risk of fire or shock, do not
expose this product to rain or moisture.
Always install this product in a location with adequate ventilation, at least 20 in (50
cm) from adjacent surfaces.
Be sure that no ventilation slots on the unit’s housing are blocked.
Never connect this product to a dimmer.
Make sure to replace the fuse with another of the same type and rating.
Never carry this product from the power cord or any moving part. Always use the
hanging/mounting bracket or the handles.
The maximum ambient temperature (Ta) is 104° F (40° C). Do not operate this
product at higher temperatures.
In the event of a serious operating problem, stop using the unit immediately.
Never try to repair this product. Repairs carried out by unskilled people can lead to
damage or malfunction. Please contact the nearest authorized technical assistance
center.
Keep this User Manual for future consultation. If you sell this product to another user,
be sure that they also receive this document.

LFS-5 User Manual (Rev. 08) Page 5 of 14
2. I NTRODUCTION
Product Overview
FuseHolder
MountingBracket
FramingShutter(x4)
Bracket
AdjustmentKnob PowerOut
PowerIn
Goboholderknob
Focusandzoom
control
Gelholde
r
FramingShutter(x4)

Page 6 of 14 LFS-5 User Manual (Rev. 08)
Product Dimensions

LFS-5 User Manual (Rev. 08) Page 7 of 14
3.SETUP
AC Power This product has an auto-ranging power supply and it can work with an input voltage
range of 100~240 VAC, 50/60 Hz.
To determine the power requirements for this product (circuit breaker, power outlet, and
wiring), use the current value listed on the label affixed to the product’s back panel, or
refer to the product’s specifications chart. The listed current rating indicates the
product’s average current draw under normal conditions.
Always connect this product to a protected circuit (circuit breaker or fuse),
making sure that it has an appropriate electrical ground to avoid the risk of
electrocution or fire.
Never connect this product to a rheostat (variable resistor) or dimmer circuit, even
if the rheostat or dimmer channel serves only as a 0 to 100% switch.
Fuse
Replacement Follow the instructions below to change the fuse, if necessary.
Disconnect this product from the power outlet before replacing the fuse.
1) Wedge the tip of a flat head screwdriver into the slot of the fuse holder and pry
out of its housing.
2) Remove the blown fuse from its holder and replace with a fuse of the exact
same type and rating.
3) Insert the fuse holder back into place, and reconnect power.
Although the safety cap does have room for a spare fuse, this product ships with
no spare fuse.
Always replace a blown fuse of the same type and rating.

Page 8 of 14 LFS-5 User Manual (Rev. 08)
Power Linking
This product provides power linking via the Edison outlet located in the back of the unit.
Please see the diagram below for further explanation.
PowerLinkingDiagram
You can power link up to 23 LFS-5 units on 120 VAC or up to 45 LFS-5 units on
230 VAC.
The power linking diagram shown above corresponds to the North American
version of this product ONLY! If using this product in other markets, you must
consult with the local CHAUVET® distributor as power linking connectors and
requirements may differ in your country or region.
1
st
Product 2
nd
Product 3
r
d
Product
Otherproducts

LFS-5 User Manual (Rev. 08) Page 9 of 14
Mounting
Before mounting this product, read and follow the safety recommendations indicated in
the Safety Notes section (page 2 of this manual).
Orientation
The LFS-5 may be mounted in any position; however, make sure adequate ventilation is
provided around the product.
Rigging
Before deciding on a location for this product, always make sure that it will be easy to
access the unit for maintenance purposes.
Make sure that the structure onto which you are mounting this product can support its
weight. Please see the Technical Specifications section of this manual for weight
information.
When mounting this product overhead, always use a safety cable. Mount the product
securely to a rigging point, whether an elevated platform or a truss.
When rigging this product onto a truss, you should use a mounting clamp of appropriate
weight capacity. The bracket has a 13 mm hole, which is appropriate for this purpose.
When power linking multiple products, you must always consider the length of the power
linking cable and mount the products close enough for the cable to reach.
The bracket adjustment knobs allow for directional adjustment when aiming the product
to the desired angle. Only loosen or tighten the bracket knobs using your bare hands.
Using tools could damage the knobs.
MountingDiagram
MountingBracket
Texthere
BracketAdjustmentKnob

Page 10 of 14 LFS-5 User Manual (Rev. 08)
4.OPERATION
Power To turn on your LFS-5, simply plug in the including power cord to the back of the product
and plug the opposite end to the wall outlet. To turn it off, unplug the power from the wall
outlet.
Framing
Shutters To control the shape of the beam from the LFS-5, use the framing shutters on all sides
of the product. The left framing shutter controls the right side of the light, the top framing
shutter controls the bottom of the light and vice versa. Push the framing shutters in and
out depending on the size and shape of the beam that you desire.
Focus and Zoom To control focus and zoom, move the internal lenses at the front of the unit until you get
the desired focal point and zoom length.
Gobos To install a gobo into the LFS-5, unscrew the knob as shown in the Product Description
(page 5). Place the gobo into the holder and screw the gobo holder back into place.
Your chosen gobo will now display. To change the shape of the gobo, simply use the
framing shutters to select the size and shape of the gobo that you desire.
Color Gels To use a color gel (not included), simply place the gel in the front of the product, as
shown in the Product Description (page 5). Your desired color will now show.

LFS-5 User Manual (Rev. 08) Page 11 of 14
5.TECHNICAL INFORMATION
Product
Maintenance Dust build up reduces light output performance and can cause overheating. This can
lead to reduction of the light source’s life. To maintain optimum performance and
minimize wear, you should clean your lighting products at least twice a month. However,
be aware that usage and environmental conditions could be contributing factors to
increase the cleaning frequency.
To clean this product, follow the instructions below:
Unplug the product from power.
Wait until the product is cold.
Use a vacuum (or dry compressed air) and a soft brush to remove dust collected on
the external surface/vents and reachable internal components.
Clean all glass/transparent surfaces with a mild soap solution, ammonia-free glass
cleaner, or isopropyl alcohol.
Apply the solution directly to a soft, lint free cotton cloth or a lens cleaning tissue.
Softly drag any dirt or grime to the outside of the glass/transparent surface.
Gently polish the glass/transparent surfaces until they are free of haze and lint.
Always dry the glass/transparent surfaces carefully after cleaning them.

Page 12 of 14 LFS-5 User Manual (Rev. 08)
General Troubleshooting
Symptom Possible Cause Possible Action
Circuit breaker
or fuse keeps
blowing
Excessive load on the circuit Make sure that the total load
does not exceed 80% of the
breaker or fuse nominal
current
Short circuit along the
power lines Check the power lines and power cords
Product does
not power up
No energy on power outlet Check power outlet
Change to another outlet
Loose or damaged power
cord Check the power cord
Blown fuse Replace blown fuse with a
good one of the same type
and rating
Internal problem Send product for repair
If you still experience problems after trying the above solutions, contact
CHAUVET® Technical Support.

LFS-5 User Manual (Rev. 08) Page 13 of 14
Contact
Procedure In case you need to return a product or request support, follow the procedure below:
If you live in the US, contact CHAUVET® World Headquarters (see below).
If you live in the UK or Ireland, contact CHAUVET® Europe Ltd.(see below).
If you live in any other country, DO NOT contact CHAUVET®. Instead, contact your
distributor of record. Refer to our Web site for contact details of distributors outside
the US, United Kingdom, or Ireland.
CHAUVET®
Contact
Information
World Headquarters
CHAUVET®
General Information
Address: 5200 NW 108th Avenue
Sunrise, FL 33351
Voice: [phone]
Fax: [phone]
Toll free: [phone]
United Kingdom & Ireland
CHAUVET® Europe Ltd.
General Information
Address: Unit 1C
Brookhill Road Industrial Estate
Pinxton, Nottingham, UK
NG16 6NT
Voice: [phone]
Fax: [phone]
Technical Support
Voice: [phone] (Press 4)
Fax: [phone]
Email: [email protected]
Technical Support
Email: [email protected]
World Wide Web
www.chauvetlighting.com
World Wide Web
www.chauvetlighting.co.uk
If you live outside the US, United Kingdom, or Ireland, contact your distributor of
record and follow their instructions on how to return CHAUVET® products to
them. Visit our Web site for contact details.
Returning
Products to
CHAUVET®
Call the corresponding CHAUVET® Tech Support office and request a Return
Merchandise Authorization (RMA) number before shipping the product. Be prepared to
provide the model number, serial number, and a brief description of the cause for the
return.
You must send the merchandise prepaid, in its original box, and with its original packing
and accessories. CHAUVET® will not issue call tags.
Clearly label the package with the RMA number. CHAUVET® will refuse any product
returned without an RMA number.
DO NOT write the RMA number directly on the box. Instead, write it on a properly
affixed label.
Before sending the product, clearly write the following information on a piece of paper
and place it inside the box:
Your name
Your address
Your phone number
The RMA number
A brief description of the problem
Be sure to pack the product properly. Any shipping damage resulting from inadequate
packaging will be your responsibility. As a suggestion, proper UPS packing or double-
boxing is always a safe method to use.
CHAUVET® reserves the right to use its own discretion to repair or replace
returned product(s).

Page 14 of 14 LFS-5 User Manual (Rev. 08)
6.TECHNICAL SPECIFICATIONS
Dimensions and
Weight Length Width Height Weight
12.7in (325mm) 8in (205mm) 9in (229mm) 3.2lbs (1.5kg)
Note: Dimensions in inches rounded to the nearest decimal digit.
Power Power Supply Type Range Voltage Selection
Switching (internal) 100~240V, 50/60Hz Auto-ranging
Parameter 120V, 60Hz 230V, 50Hz
Consumption 52W 56W
Operating 0.4A 0.2A
Power linking current (units) 8A (23 units) 8A (45 units)
Fuse F2A, 250V F2A, 250V
Power I/O US/Worldwide UK/Europe
Power input connector IEC IEC
Power output connector Edison IEC
Power Cord plug Edison (US) Local plug
Light Source Type Power Lifespan
LED 23W (15.3A) 50,000 hours
Photo Optic Parameter
Illuminance @ 16º 1990 lx @ 2m
Illuminance @ 24º 967 lx @ 2m
Zoom angle 16-24º
Gobo size 25.4 mm outside
19 mm image
1 mm max thickness
Thermal Maximum External Temp. Cooling System
104°F (40°C) Convection
Ordering Product Name Item Code Item Number
LFS-5 08050400 LFS-5