Chauvet TRIDENT User manual

5200 NW 108th Avenue, Sunrise, FL 33351 U.S.A.
[phone] – [phone]
FAX [phone]
www.chauvetlighting.com
User Manual
Snapshot
Use on Dimmer
Outdoor Use
Sound Activated
DMX
Master/Slave
Auto-ranging
Power Supply
Replaceable Fuse
User Serviceable
Duty Cycle

TABLE OF CONTENTS
1. BEFORE YOU BEGIN...................................................................................................................................................3
WHAT IS INCLUDED................................................................................................................................................................................3
UNPACKING INSTRUCTIONS ....................................................................................................................................................................3
MANUAL CONVENTIONS .........................................................................................................................................................................3
ICONS ..................................................................................................................................................................................................3
SAFETY INSTRUCTIONS..........................................................................................................................................................................4
2. INTRODUCTION ...........................................................................................................................................................4
FEATURES............................................................................................................................................................................................4
PRODUCT OVERVIEW.............................................................................................................................................................................5
3. SETUP ..........................................................................................................................................................................6
ACPOWER...........................................................................................................................................................................................6
Power Linking...........................................................................................................................................................6
MOUNTING............................................................................................................................................................................................6
Orientation................................................................................................................................................................6
Rigging .....................................................................................................................................................................6
4. OPERATING INSTRUCTIONS......................................................................................................................................7
CONFIGURING THE STARTING ADDRESS..................................................................................................................................................7
DMXOPERATION..................................................................................................................................................................................7
MASTER/SLAVE.....................................................................................................................................................................................7
STANDALONE OPERATION......................................................................................................................................................................7
Automatic..................................................................................................................................................................7
Sound-Active ............................................................................................................................................................7
Custom Program.......................................................................................................................................................8
DMXCHANNEL VALUES ........................................................................................................................................................................8
DIPSWITCH VALUES.............................................................................................................................................................................8
5. APPENDIX.................................................................................................................................................................... 9
GENERAL MAINTENANCE........................................................................................................................................................................9
POWER LINKING....................................................................................................................................................................................9
SETTING THE STARTING ADDRESS..........................................................................................................................................................9
GENERAL TROUBLESHOOTING..............................................................................................................................................................10
RETURNS ...........................................................................................................................................................................................11
CLAIMS ..............................................................................................................................................................................................11
TECHNICAL SPECIFICATIONS ................................................................................................................................................................12
CONTACT US......................................................................................................................................................................................12
CHAUVET®, 2012, All Rights Reserved. Information and specifications in this User Manual are subject to change without notice. CHAUVET® assumes no
responsibility or liability for any errors or inaccuracies that may appear in this manual.

1. Before You Begin 3 Rev. 2
1.BEFORE YOU BEGIN
What is Included
1 x Trident™
1 x Power Cable
1 x Warranty Card
1 x User Manual
Unpacking Instructions
Immediately upon receiving a fixture, carefully unpack the carton, check the contents to ensure that
all parts are present, and have been received in good condition. Notify the shipper immediately and
retain packing material for inspection if any parts appear damaged from shipping or the carton itself
shows signs of mishandling. Save the carton and all packing materials. In the event that a fixture
must be returned to the factory, it is important that the fixture be returned in the original factory box
and packing.
Manual Conventions
CHAUVET® manuals use the following conventions to differentiate certain types of information from
the regular text.
CONVENTION MEANING
[10] A DIP switch to be configured
<Menu> A key to be pressed on the fixture’s control panel
1~512 A range of values
50/60 A set of values of which only one can be chosen
Settings A menu option not to be modified (for example, showing the operating
mode/current status)
MENU > Settings A sequence of menu options to be followed
ON A value to be entered or selected
Icons
This manual uses the following icons to indicate information that requires special attention on the part
of the user.
ICONS MEANING
C
ritical installation, configuration or operation information. Failure to
comply with this information may render the fixture partially or completely
inoperative, cause damage to the fixture or cause harm to the user.
Important installation or configuration information. Failure to comply with
this information may prevent the fixture from functioning correctly.
Useful information.

1. Before You Begin 4 Rev. 2
Safety Instructions
•Please keep this User Manual for future consultation. If you sell the unit to another user, be sure that
they also receive this instruction booklet.
•Always make sure that you are connecting to the proper voltage, and that the line voltage you are
connecting to is not higher than that stated on the decal or rear panel of the fixture.
•This product is intended for indoor use only! To prevent risk of fire or shock, do not expose fixture to
rain or moisture.
•Make sure there are no flammable materials close to the unit while operating.
•The unit must be installed in a location with adequate ventilation, at least 20 in (50 cm) from adjacent
surfaces. Be sure that no ventilation slots are blocked.
•Always disconnect from power source before servicing or replacing fuse and be sure to replace with
same fuse source.
•Secure fixture to fastening device using a safety chain.
•Maximum ambient temperature (Ta) is 104° F (40° C). Do not operate fixture at temperatures higher
than this.
•In the event of a serious operating problem, stop using the unit immediately. Never try to repair the
unit by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please
contact the nearest authorized technical assistance center.
•Never connect the device to a dimmer pack.
•Make sure the power cord is never crimped or damaged.
•Never disconnect the power cord by pulling or tugging on the cord.
•Never carry the fixture directly from the cord. Always use the hanging/mounting bracket.
•Avoid direct eye exposure to the light source while it is on.
2.INTRODUCTION
Features
•3-channel DMX-512 LED centerpiece
•Individual control of red, green and blue
•Variable electronic strobe in any color combination
•Back-and-forth motor effect with variable speed
•Static colors with or without DMX controller
Additional Features
•Built-in automated programs
•Built-in sound activated programs
•Tri-color LEDs (2,550 mA total)
•Additional power output: max 26 units
Please read these instructions carefully. It includes important
information about the installation, usage and maintenance of this
product.

2. Introduction 5 Rev. 2
Product Overview
Safety attachment
point
Hanging bracket
Fuse holder
Power in
Power out
DMX in
DMX out
DIP switches
Microphone
Microphone
sensitivity
adjustment knob
Back Panel A
Back Panel B

3. Setup 6 Rev. 2
3.SETUP
AC Power This fixture runs on 100~240 VAC, 50/60 Hz. Before powering on the unit, make sure the line voltage
to which you are connecting it is within the range of accepted voltages.
Always connect the fixture to a switched circuit. Never connect the fixture to a rheostat
(variable resistor) or dimmer circuit, even if the rheostat or dimmer channel is used only as a 0
to 100% switch.
To determine the power requirements for a particular fixture, see the label affixed to the back of the
fixture or refer to the Technical Specifications. A fixture’s listed current rating indicates its average
current draw under normal conditions.
Always connect the fixture to a circuit with a suitable electrical ground.
Power Linking
This fixture contains power linking via the edison outlet located next to the power input cable.
The maximum quantity of fixtures that may be linked is 26.
Mounting
Orientation
The Trident™ may be mounted in any safe position, provided there is adequate room for ventilation.
Rigging
Be sure that the structure can support the weight of the fixture. Mount the product securely. This may
be done with a screw, nut and bolt, or a hanging clamp. Be sure to also use a safety cable. The hole
in each bracket is 13 mm in size. When rigging consider routine maintenance and control panel
access. Please see the following steps for installation.
•If the power link out is intended to be used with multiple fixture, take into account the length
of each power cable, and mount the fixtures close enough to one another to accommodate
for this.
•When aiming the fixture, you may use the bracket adjustment knobs (2x). Loosen each
knob, adjust to the desired angle, and then tighten both knobs by turning clockwise. Do not
use tools for this step, as it may cause damage.
•Safety cables must always be used.
Additional power
link out
Fixture 1
Fixture 2
Fixture 3

4. Operating Instructions 7 Rev. 2
4.OPERATING INSTRUCTIONS
Configuring the Starting Address
Each fixture requires a starting address from 1~512. A fixture requiring one or more channels for control begins
to read the data on the channel indicated by the starting address. For example, a fixture that uses seven DMX
channels and is addressed to start on DMX channel 100, will read data from channels: 100, 101, 102, 103, 104,
105 and 106. Choose the starting addresses for each fixture so that the channels used do not overlap. In
addition, you should note the starting address selected for future reference. The Trident™ fixture uses 3 DMX
channels.
DMX Operation
This is the operating mode which will allow for control with an external DMX controller. You must set the starting
address for this mode. If you are unfamiliar with DMX, download the DMX Primer from
www.chauvetlighting.com.
1. Plug the fixture into power.
2. Connect DMX cable(s) to controller.
3. Turn DIP switch [10] to the ON position.
4. Use DIP switches 1~9 to set the starting address.
Master/Slave
This is the operating mode which will allow 1 fixture to act as the “master” and control all of the other “slave”
fixtures. You must set both the master and the slave(s) fixtures to the correct mode for this operation. They
must also be connected using DMX cables, in a daisy chain fashion.
Master Settings:
1. Using the DIP switches, set the master fixture to one of the following modes: custom, automatic,
or sound-activated.
Slave Settings:
1. Turn DIP switch [10] to the ON position.
2. Turn DIP switches 1~9 to the OFF position.
Do not connect a DMX controller to the daisy chain for this operation.
Standalone Operation
Automatic
This fixture has a preprogrammed chase. This is accessed via the DIP switches:
1. Plug the fixture into power.
2. Turn DIP switch [8] to the ON position.
3. Turn all other DIP switches to the OFF position.
Do not connect a DMX controller to the daisy chain for this operation.
Sound-Active
This fixture has a preprogrammed sound triggered chase. This is accessed via the DIP switches, and the
speed may be adjusted using the audio adjustment knob. Please see the instructions below for further
explanation.
1. Plug the fixture into power.
2. Turn DIP switch [9] to the ON position.
3. Turn all other DIP switches to the OFF position.
Do not connect a DMX controller to the daisy chain for this operation.

4. Operating Instructions 8 Rev. 2
Custom Program
This fixture has individual control over each of the following functions via DIP switches: color, strobe, and
motor rotation. These functions may be combined in any combination. Please see the instructions below
for further explanation.
1. Plug the fixture into power.
2. Turn DIP switches [8] ~ [10] to the OFF position.
3. DIP switches [1] ~ [3] control the color. These may be combined.
4. DIP switches [4] ~ [6] control the strobe speed. Only 1 of these may be selected at a time.
Turning them all to the OFF position allows the color to remain on constant.
5. DIP switch [7] controls the motor rotation. Turning this to the ON position will cause the motor to
rotate CW/CCW at a preset speed. This may not be altered.
Do not connect a DMX controller to the daisy chain for this operation.
DMX Channel Values
CHANNEL
VALUE
FUNCTION
1
000 004
005 028
029 056
057 084
085 112
113 140
141 168
169 197
198 224
225 255
Color Selection (no dimming)
Blackout
Red
Green
Blue
Green/Blue
Red/Blue
Red/Green
Red/Green/Blue
3-color chase
7-color chase
2
000 004
005 255
Strobe
No function
Strobe (slow fast)
3
000 127
128 255
Rotation
Indexing
Rotate (fast to slow)
DIP Switch Values
FUNCTIONS
DIP SWITCHES
NOTES &DESCRIPTION
Red
1
Combine these DIP switches to trigger simultaneously
Green
2
Blue
3
Strobe (slow)
4
Only 1 of these may be selected at a time
Strobe (medium)
5
Strobe (fast)
6
Motor
7
ON = bi-directional rotation
Automatic
8
Overrides DIP switches 1~6
Sound-activated
9
Overrides DIP switches 1~6
DMX /Slave
10
DMX mode/Slave mode activation

5. Appendix 9 Rev. 2
5.APPENDIX
General Maintenance
To maintain optimum performance and minimize wear, fixtures should be cleaned frequently. Usage and
environment are contributing factors in determining frequency. As a general rule, fixtures should be cleaned at
least twice a month. Dust build up reduces light output performance and can cause overheating. This can lead
to reduced lamp life and increased mechanical wear. Be sure to power off fixture before conducting
maintenance.
•Unplug fixture from power.
•Use a vacuum or air compressor and a soft brush to remove dust collected on external
vents.
•Clean all glass when the fixture is cold with a mild solution of glass cleaner or Isopropyl
Alcohol and a soft lint free cotton cloth or lens tissue.
•Apply solution to the cloth or tissue and drag dirt and grime to the outside of the lens.
•Gently polish optical surfaces until they are free of haze and lint.
The cleaning of external optical lenses and/or mirrors must be carried out periodically to optimize light output.
Cleaning frequency depends on the environment in which the fixture operates. Damp, smoky or particularly dirty
surroundings can cause greater accumulation of dirt on the unit’s optics. Clean with soft cloth using normal
glass cleaning fluid. Clean the external optics at least every 20 days. Clean the fixture at least every 30/60
days.
Always dry the parts carefully after cleaning them.
Never spin a fan using compressed air.
Power Linking
You will need a serial data link to run light shows of one or more fixtures using a DMX controller or to run
synchronized shows on two or more fixtures set to a master/slave operating mode. The combined number of
channels required by all the fixtures on a serial data link determines the number of fixtures the data link can
support.
Fixtures on a serial data link must be daisy chained in one single line. To comply with the EIA-485
standard, no more than 32 fixtures should be connected on one data link. Connecting more than 32
fixtures on one serial data link without the use of a DMX optically-isolated splitter may result in
deterioration of the digital DMX signal.
Maximum recommended serial data link distance: 500 m (1640 ft)
Maximum recommended number of fixtures on a serial data link: 32
Setting the Starting Address
This DMX mode enables the use of a universal DMX controller device. Each fixture requires a start address
from 1~512. A fixture requiring one or more channels for control begins to read the data on the channel
indicated by the start address. For example, a fixture that uses six DMX channels and was addressed to start
on DMX channel 100, would read data from channels: 100, 101, 102, 103, 104, and 105. Choose start
addresses so that the channels used do not overlap, and note the start address selected for future reference. If
you are unfamiliar with DMX, download the DMX Primer from www.chauvetlighting.com.

5. Appendix 10 Rev. 2
General Troubleshooting
SYMPTOM POSSIBLE CAUSE(S) POSSIBLE ACTION(S)
Breaker/Fuse
keeps blowing
Excessive circuit load Check total load placed on the electrical circuit.
Short circuit along the power wires Check for a short in the electrical wiring (internal and/or
external)
Device does not
power up No power Check for power on power outlet
Loose power cord Check power cord
Fixture is not
responding to
DMX
Wrong DMX addressing Check Control Panel and unit addressing
Damaged DMX cables Check DMX cables
Wrong polarity settings on the
controller Check polarity switch settings on the controller
Loose DMX cables Check cable connections
Faulty DMX interface Replace DMX input
Faulty Main PCB Replace Main PCB
Loss of signal
Non DMX cables Use only DMX compatible cables
Bouncing signals Install terminator as suggested
Long cable / Low level signal Install amplifier right after fixture with strong signal
Too many fixtures Install an optically coupled DMX splitter after unit #32
Interference from AC wires Keep DMX cables separated from power cables or black
lights
If you still have a problem after trying the above solutions, please contact CHAUVET®
Technical Support.

5. Appendix 11 Rev. 2
Returns Returned merchandise must be sent prepaid and in the original packing; call tags will not be issued.
Package must be clearly labeled with a Return Merchandize Authorization Number (RMA #).
Products returned without the RMA # will be refused. Call CHAUVET® and request an RMA # prior to
shipping the fixture. Be prepared to provide the model number, serial number and a brief description
of the cause for the return. Be sure to pack fixture properly; any shipping damage resulting from
inadequate packaging is the customer’s responsibility. FedEx packing or double-boxing are
recommended.
CHAUVET® reserves the right to use its own discretion to repair or replace product(s).
If you are given an RMA #, please include the following information on a piece of paper inside
the box:
1) Your name
2) Your address
3) Your phone number
4) The RMA #
5) A brief description of the symptoms
Claims Damage incurred in shipping is the responsibility of the shipper; therefore, the damage must be
reported to the carrier upon receipt of merchandise. It is the customer’s responsibility to notify and
submit claims with the shipper in the event that a fixture is damaged due to shipping. Any other claim
for items such as missing component/part, damage not related to shipping, and concealed damage,
must be made within seven (7) days of receiving merchandise.

Technical Specifications 12 Rev. 2
Technical Specifications
WEIGHT & DIMENSIONS
Length........................................................................................................................10.5 in (269 mm)
Width..........................................................................................................................12.1 in (308 mm)
Height ........................................................................................................................13.7 in (348 mm)
Weight..............................................................................................................................8 lbs (3.6 kg)
POWER
Auto-ranging Power Supply.............................................................................100~240 VAC, 50/60 Hz
Power Consumption @ 120 VAC, 60 Hz...............................................16 W (0.3 A) max, 0.1 A inrush
Power Consumption @ 230 VAC, 50 Hz ...............................................16 W (0.2 A) max, 0.2 A inrush
Power output.....................................................................................................................26 units max
Fuse..................................................................................................................................F 1 A, 250 V
LIGHT SOURCE
LED.......................................................................................................2, 3 W (850 mA x3) 50,000 hrs
PHOTO OPTIC
Coverage Angle ............................................................................................................................155°
THERMAL
Maximum ambient temperature......................................................................................104° F (40° C)
CONTROL & PROGRAMMING
Data input ............................................................................................. locking 3-pin XLR male socket
Data output ........................................................................................ locking 3-pin XLR female socket
Data pin configuration ............................................................................pin 1 shield, pin 2 (-), pin 3 (+)
Protocols.....................................................................................................................DMX-512 USITT
DMX Channels....................................................................................................................................3
ORDERING INFORMATION
Trident™...............................................................................................................................TRIDENT
WARRANTY INFORMATION
Warranty ...........................................................................................................2-year limited warranty
Contact Us
World Wide General Information CHAUVET
5200 NW 108th Avenue
Sunrise, FL 33351
voice: 954.929.1115
fax: [phone]
toll free: 800.762.1084
Technical Support CHAUVET
5200 NW 108th Avenue
Sunrise, FL 33351
voice: 954.929.1115 (Press 4)
fax: [phone] (Attention: Service)
World Wide Web www.chauvetlighting.com