Chauvet Colorado 1-Quad Tour User manual

User Manual

Edition Notes
Colorado™ 1-Quad Zoom Tour User Manual Rev. 1
Edition
Notes
The Colorado™ 1-Quad Zoom Tour User Manual Rev. 1 covers the description, safety
precautions, installation, programming, operation, and maintenance of the Colorado™ 1-Quad
Zoom Tour. Chauvet released this edition of the Colorado™ 1-Quad Zoom Tour
User Manual in
December 2014.
Trademarks
CHAUVET® is a registered trademark of CHAUVET & Sons Inc. (d/b/a CHAUVET® or
Chauvet). The CHAUVET® logo in its entirety including
the CHAUVET® name and the dotted
triangle, and all other trademarks in this manual pertaining to services, products, or marketing
statements (example: It’s Green Thinking™) are owned or licensed by Chauvet
. Any other
product names, logos, brands, company
names, and other trademarks featured or referred to
within this document are the property of their respective trademark holders.
Copyright Notice
Chauvet owns the content of this User Manual in its entirety, including but not limited to
pictures, logos, trademarks, and resources.
© Copyright 2014 Chauvet. All rights reserved.
Electronically published by Chauvet in the United States of America.
Manual Use
Chauvet authorizes its customers to download and print this manual for professional information
purposes only. Chauvet expressly prohibits the usage, copy, storage, distribution, modification,
or printing of this manual or its content for any other purpose without written consent from
Chauvet.
Document
Printing
For better results, print this document in color, on letter size paper (8.5 x 11 in), double-sided. If
using A4 paper (210 x 297 mm), configure your printer to scale the content accordingly.
Intended
Audience
Any person in charge of installing, operating, and/or maintaining this product should completely
read through the guide that shipped with the product, as well as this manual, before installing,
operating, or maintaining this product.
Disclaimer
Chauvet believes that the information contained in this manual is accurate in all respects.
However, Chauvet assumes no responsibility for any errors or omissions in this document.
Chauvet reserves the right to revise and make changes to the content of this document without
obligation that Chauvet notify any person or company of such revision or changes. This does
not in any way constitute a commitment by Chauvet to make such changes. Chauvet may issue
a revision of this manual or a new edition to incorporate such changes.
Document
Revision
The Colorado™ 1-Quad Zoom Tour User Manual Rev. 1 is the first edition of this manual. Go to
www.chauvetprofessional.com for the latest version.
Author
Date
Editor
Date
D. Couppe
12/10/14
A. Leon
12/10/14

Table of Contents
Colorado™ 1-Quad Zoom Tour User Manual Rev. 1 -i-
Table of Contents
1. Before You Begin......................................................................................................................................1
What Is Included...........................................................................................................................................................1
Claims..........................................................................................................................................................................................1
Manual Conventions ....................................................................................................................................................................1
Symbols.......................................................................................................................................................................................1
Product At A Glance .....................................................................................................................................................1
Safety Notes .................................................................................................................................................................2
Personal Safety............................................................................................................................................................................2
Mounting And Rigging..................................................................................................................................................................2
Power And Wiring ........................................................................................................................................................................2
Operation.....................................................................................................................................................................................2
Expected LED Lifespan................................................................................................................................................2
2. Introduction...............................................................................................................................................3
Description....................................................................................................................................................................3
Features........................................................................................................................................................................3
Overview.......................................................................................................................................................................4
Dimensions...................................................................................................................................................................5
3. Setup..........................................................................................................................................................6
AC Power......................................................................................................................................................................6
AC Plug........................................................................................................................................................................................6
Power Linking ...............................................................................................................................................................6
DMX Linking..................................................................................................................................................................6
DMX Personalities........................................................................................................................................................................6
Master/Slave Connectivity............................................................................................................................................................6
Mounting.......................................................................................................................................................................7
Orientation ...................................................................................................................................................................................7
Rigging.........................................................................................................................................................................................7
Procedure ....................................................................................................................................................................................7
4. Operation...................................................................................................................................................8
Control Panel Description.............................................................................................................................................8
Control Options............................................................................................................................................................................8
Programming................................................................................................................................................................................8
Control Panel Lock .......................................................................................................................................................8
Passcode.....................................................................................................................................................................................8
Settings Lock ................................................................................................................................................................8
Menu Map.....................................................................................................................................................................9
Menu Map (Cont.).......................................................................................................................................................10
Menu Map (Cont.).......................................................................................................................................................11
Configuration (Standalone).........................................................................................................................................12
Auto Programs...........................................................................................................................................................................12
Edit Custom Programs..............................................................................................................................................................12
Master/Slave..............................................................................................................................................................................12
Color Settings.............................................................................................................................................................................12
Dimmer Profiles..........................................................................................................................................................................13
Curve Settings............................................................................................................................................................................13
Program Upload.........................................................................................................................................................................13
Reset..........................................................................................................................................................................................13
Whites Setting............................................................................................................................................................................14
Whites Setting Factory Reset.....................................................................................................................................................14
White Calibration........................................................................................................................................................................14
Static Color ................................................................................................................................................................................14
Configuration (DMX)...................................................................................................................................................15
DMX Personalities......................................................................................................................................................................15

Table of Contents
-ii- Colorado™ 1-Quad Zoom Tour User Manual Rev. 1
DMX Control...............................................................................................................................................................................15
Loss Of Signal Setting................................................................................................................................................................15
Zoom Limit Settings ...................................................................................................................................................................15
DMX Values................................................................................................................................................................16
DMX Values (Cont.)....................................................................................................................................................17
DMX Values (Cont.)....................................................................................................................................................18
DMX Values (Cont.)....................................................................................................................................................19
DMX Values (Cont.)....................................................................................................................................................20
DMX Values (Cont.)....................................................................................................................................................21
DMX Values (Cont.)....................................................................................................................................................22
DMX Values (Cont.)....................................................................................................................................................23
DMX Values (Cont.)....................................................................................................................................................24
COLORado™ 1-Quad Zoom Tour Pixel Selection for DMX Control..........................................................................24
DMX Values (Cont.)....................................................................................................................................................25
DMX Values (Cont.)....................................................................................................................................................26
5. Technical Information.............................................................................................................................27
Product Maintenance..................................................................................................................................................27
6. Technical Specifications.........................................................................................................................28
Returns .......................................................................................................................................................................29
Contact Us...................................................................................................................................................29

Before You Begin
Colorado™ 1-Quad Zoom Tour User Manual Rev. 1 -1-
1. BEFORE YOU BEGIN
What Is
Included
•Colorado™ 1-Quad Zoom Tour
•Neutrik® powerCON® power cord
•Gel frame holder (7.5 in/191 mm accessories)
•Gel frame
•Safety cable
•Warranty Card
•
Quick Reference Guide
Claims
Carefully unpack the product immediately and check the box to make sure all the parts are in
the package and are in good condition.
If the box or the contents (the product and incl
uded accessories) appear damaged from
shipping or show signs of mishandling, notify the carrier immediately, not Chauvet
. Failure to
report damage to the carrier immediately may invalidate your claim. In addition, keep the box
and contents for inspection.
For other issues, such as missing components or parts, damage not related to shipping, or
concealed damage, file a claim with Chauvet within 7 days of delivery.
Manual
Conventions
Convention
Meaning
1–512
A range of values in the text
50/60
A set of mutually exclusive values in the text
<SET>
A button on the product’s control panel
Settings
A product function or a menu option
MENU>Settings
A sequence of menu options
1–10
A range of menu values from which to choose in a menu
Yes/No
A set of two mutually exclusive menu options in a menu
ON
A unique value to be entered or selected in a menu
Symbols
Symbols Meaning
Critical installation, configuration, or operation information. Failure to
comply with this information may cause the product not to work,
damage third-party equipment, or cause harm to the operator.
Important installation or configuration information. Failure to comply
with this information may keep the product from working.
Useful information.
The term “DMX” used throughout this manual refers to the USITT DMX512-A digital data
transmission protocol.
Product At A
Glance
Use on Dimmer
x
Auto Programs
P
Outdoor Use
x
Auto-Ranging Power
Supply
P
Master/Slave
P
Replaceable Fuse
P
DMX
P
User-Serviceable
x

Before You Begin
-2- Colorado™ 1-Quad Zoom Tour User Manual Rev. 1
Safety Notes
Read all the following Safety Notes before working with this product. These notes include
important information about the installation, usage, and maintenance of this product.
This product contains no user-serviceable parts. Any reference to servicing in this User
Manual will only apply to properly trained Chauvet certified technicians. Do not open the
housing or attempt any repairs.
All applicable local codes and regulations apply to proper installation of this product.
Personal Safety
•Avoid direct eye exposure to the light source while the product is on.
•Always disconnect this product from its power source before servicing.
•Always connect this product to a grounded circuit to avoid the risk of electrocution.
•Do not touch this product’s housing during operation because it may be very hot.
Mounting And
Rigging
•This product is for indoor use only! To prevent risk of fire or shock, do not expose this
product to rain or moisture. (IP20)
•CAUTION: When transferring product from extreme temperature environments, (e.g. cold
truck to warm humid ballroom) condensation may form on the internal electronics of the
product. To avoid causing a failure, allow product to fully acclimate to the surrounding
environment before connecting it to power.
•Mount this product in a location with adequate ventilation, at least 20 in (50 cm) from
adjacent surfaces.
•Make sure there are no flammable materials close to this product while it is operating.
•When hanging this product, always secure to a fastening device using a safety cable
(included).
Power And
Wiring
•Always make sure you are connecting this product to the proper voltage in accordance with
the specifications in this manual or on the product’s specification label.
•To eliminate unnecessary wear and improve its lifespan, during periods of non-use
completely disconnect the product from power via breaker or by unplugging it.
•Never connect this product to a dimmer pack or rheostat.
•Never disconnect this product by pulling or tugging on the power cable.
Operation
•Do not operate this product if you see damage on the housing, lenses, or cables. Have the
damaged parts replaced by an authorized technician at once.
•Do not cover the ventilation slots when operating to avoid internal overheating.
•The maximum ambient temperature is 113 °F (45 °C). Do not operate this product at a
higher temperature.
•In case of a serious operating problem, stop using this product immediately!
In the unlikely event that your Chauvet product may require service, contact Chauvet
Technical Support.
Expected LED
Lifespan
LEDs gradually decline in brightness over time, mostly because of heat. Packaged in clusters,
LEDs exhibit higher operating temperatures than in ideal, single-
LED conditions. For this
reason, using clustered LEDs at their fullest intensity significantly reduces the LEDs’ lifespan.
Under normal conditions, this lifespan can be 40,000 to 50,000 hours. If extending this lifespan
is vital, lower the operating temperature by improving the ventilation around the product and
reducing the ambient temperature to an optimal operating range. In addition, limiting the overall
projection intensity may also help to extend the LEDs’ lifespan.

Introduction
Colorado™ 1-Quad Zoom Tour User Manual Rev. 1 -3-
2. INTRODUCTION
Description
The COLORado™ 1-Quad Zoom Tour is a high-power quad-color (RGBW) LED wash product
with color mixing and zoom control. This product consists of a single module that houses the
internal power supply, the control panel, the LED drivers, the LED boards, and motorized moving
lenses, as well as the power and signal connectors. The COLORado™ 1-
Quad Zoom Tour
features a variable zoom, which enables the user to change the beam angle of the product via
DMX or control panel, and a double-
bracketed yoke that can serve as a floor mount or hanging
support bracket.
Features
•3, 4, 5, 6, 7, 10, 12, 17 or 25-channel quad-color LED wash product
•Operating modes:
•3-channel: RGB control
•3-channel: HSV control
•4-channel: RGB, dimmer
•4-channel: RGBW
•5-channel: RGBW, dimmer
•6-channel: RGBW, dimmer, strobe
•7-channel: RGBW, dimmer, zoom, zoom reset
•10-channel: RGBW, dimmer, strobe, color macro, auto/custom, dimmer speed, auto
speed **
•12-channel: RGBW, dimmer, strobe, color macro, auto/custom, dimmer speed, auto
speed, zoom, zoom reset
•17-channel: 16-bit RGBW and dimmer; strobe, color macro, auto/custom, dimmer speed,
auto speed, zoom, zoom reset
•17-channel: 16-bit RGBW and dimmer; strobe, color macro, auto/custom, dimmer speed,
auto speed, zoom, zoom reset
•25-channel: 16-bit RGBW pixel control and dimmer; strobe, color macro, auto/custom,
dimmer speed, auto speed, zoom, zoom reset
•Built-in auto and custom programs recalled via DMX and Master/Slave
•RGBW color mixing via DMX or manually
•Zoomable, with a wide zoom range for design versatility
•Tough road-ready construction
•Individual control of outer pixel ring and center pixel
•Selectable, smooth dimming curves for programming versatility
•16-bit dimming of individual colors as well as master dimmer
•Neutrik® powerCON® power input/output connections
•3- and 5-pin DMX input/output connections
**Zoom locked to match Colorado™ 1-Quad series.

Introduction
-4- Colorado™ 1-Quad Zoom Tour User Manual Rev. 1
Overview
Front View
Rear View
Side View
Bracket Adjustment Knob
Power In /Out
3- Pin DMX In/Out
5-Pin DMX In/Out
Control Panel
Double-Bracketed Yoke

Introduction
Colorado™ 1-Quad Zoom Tour User Manual Rev. 1 -5-
Dimensions
9.37 in
238 mm
9.25 in
235 mm
13.14 in
334 mm
7.48 in
190 mm

Setup
-6- Colorado™ 1-Quad Zoom Tour User Manual Rev. 1
3. SETUP
AC Power
Each Colorado™ 1-Quad Zoom Tour has an auto-ranging power supply that works with an input
voltage range of 100 to 240 VAC, 50/60 Hz. To determine the power
requirements for each
Colorado™ 1-Quad Zoom Tour, refer to the label affixed to the product. You can also refer to
the Technical Specifications chart in this manual.
The listed current rating indicates the maximum current draw during normal operation. For more
information, you may download Sizing Circuit Breakers from the Chauvet website
:
http://www.chauvetlighting.com/download/.
Always connect this product to a protected circuit with an appropriate electrical ground
to avoid the risk of electrocution or fire.
Never connect this product to a rheostat (variable resistor) or dimmer circuit, even if the
rheostat or dimmer channel serves only as a 0 to 100% switch.
AC Plug
The Colorado™ 1-Quad Zoom Tour comes with a power input cord terminated with a Neutrik®
powerCON® A connector on one end and an Edison plug on the other end (U.S. market). If the
power input cord that came with your product has no plug, or if you need to change the Edison
plug, use the table below to wire the new plug.
Connection Wire (U.S.) Wire (Europe) Screw Color
AC Live
Black
Brown
Yellow or Brass
AC Neutral
White
Blue
Silver
AC Ground
Green/Yellow
Green/Yellow
Green
Power Linking
The Colorado™ 1-Quad Zoom Tour supports power linking. You can power link up to
12 products at 120 V; up to 21 at 208 V; or up to 23 at 230 V. This product comes with a power
input cord. Power linking cables are available from Chauvet for purchase.
DMX Linking
You can link the Colorado™ 1-Quad Zoom Tour to a DMX controller using a 3- or 5-pin DMX
connection. If using other DMX-compatible products with the Colorado™ 1-Quad Zoom Tour
,
you can control each individually with a single DMX controller.
DMX
Personalities
The Colorado™ 1-Quad Zoom Tour uses a 3- or 5-pin DMX data connection for its 3, 4, 5, 6, 7,
10, 12, 17, or 25-channel DMX personalities.
•Refer to the Introduction chapter for a brief description of each DMX personality.
•Refer to the Operation chapter to learn how to configure the Colorado™ 1-Quad Zoom Tour
to work in these personalities.
•The DMX Values section provides you with detailed information regarding the DMX
personalities.
If you are not familiar with or need more information about DMX standards,
Master/Slave connectivity, or the DMX cables needed to link this product to a DMX
controller, download the DMX Primer from the Chauvet website:
http://www.chauvetlighting.com/download/.
Master/Slave
Connectivity
The Master/Slave mode allows a Colorado™ 1-Quad Zoom Tour (the master) to control one or
more Colorado™ 1-Quad Zoom Tours (the slaves) without a DMX controller. One Colorado™ 1-
Quad Zoom Tour becomes the master when running an auto or custom program, or by being in
a Static mode.
You must configure each slave’s control panel to operate in Slave mode. During Master/Slave
operation, the slaves will operate in unison with the master.
DO NOT connect a DMX controller to products operating in Master/Slave mode. The DMX
controller signals may interfere with the signals from the master.
The Operation section of this manual provides detailed instructions on how to configure
the master and slaves.

Setup
Colorado™ 1-Quad Zoom Tour User Manual Rev. 1 -7-
Mounting
Before mounting this product, read and follow the Safety Notes. For our Chauvet line of
mounting clamps, go to http://trusst.com/products/.
Orientation
Always mount this product in a safe position and make sure there is adequate room for
ventilation, configuration, and maintenance.
Rigging
Chauvet recommends using the following general guidelines when mounting this product.
•When selecting an installation location, consider easy access to this product for operation,
programming adjustments, and routine maintenance.
•Make sure to mount this product away from any flammable material as indicated in the
Safety Notes.
•Never mount in places where rain, high humidity, extreme temperature changes, or
restricted ventilation may affect the product.
•If hanging this product, make sure that the mounting location can support the product’s
weight. See the Technical Specifications for the weight-bearing requirements of this
product.
•When hanging this product, always secure to a fastening device using a safety cable. For
our Chauvet line of safety cables, go to http://trusst.com/products/.
Procedure
The Colorado™ 1-Quad Zoom Tour comes with a double-bracketed yoke to which you can
either attach mounting clamps for hanging or simply use as a floor stand. You must supply your
own mounting clamps. Make sure the clamps
are capable of supporting the weight of this
product. Use at least one mounting point per product. For our Chauvet line of mounting clamps,
go to http://trusst.com/products/.
Mounting Diagram
Floor Mounting
Overhead Mounting
Safety Cable
Mounting Clamp

Operation
-8- Colorado™ 1-Quad Zoom Tour User Manual Rev. 1
4. OPERATION
Control Panel
Description
Button
Function
<MENU>
Exits from the current menu or function
<ENTER>
Enables the currently displayed menu or sets the currently selected
value in to the current function
<UP>
Navigates upward through the menu list or increases the numeric
value when in a function
<DOWN>
Navigates downward through the menu list or decreases the numeric
value when in a function
Control Options
You can set the Colorado™ 1-Quad Zoom Tour starting address in the 001–512 DMX range.
This enables control of up to 20 products in the 25-channel FULL personality.
Programming
Refer to the Menu Map to understand the menu options. The menu map shows the main level
and a variable number of programming levels for each option.
•To go to the desired main level, press <MENU> repeatedly until the option shows on the
display. Press <ENTER> to select. This will take you to the first programming level for that
option.
•To select an option or value within the current programming level, press <UP> or <DOWN>
until the option shows on the display. Press <ENTER> to select. In this case, if there is
another programming level, you will see that first option, or you will see the selected value.
•Press <MENU> repeatedly to exit to the previous main level.
Control Panel
Lock
This setting enables you to activate or disable the control panel lock, which keeps non-
authorized personnel from changing the product’s settings.
1. Go to the KEY main level.
2. Select ON or OFF.
When the control panel lock is activated, in order to access the products main
programming level, the product will prompt you to enter the passcode. Enter the
passcode as described in Passcode.
Passcode
After being prompted to enter the passcode:
•Press <UP>, <DOWN>, <UP>, <DOWN>, <ENTER>.
Settings Lock
This setting enables you to activate or disable the settings lock, which keeps non-authorized
personnel from making any changes to the programming levels under the SET main level.
1. Go to the SET main level.
2. Select SLCK.
3. Select ON or OFF.
When the settings lock is activated, in order to access the SET programming levels, the
product will prompt you to enter the passcode. Enter the passcode as descri
bed in
Passcode.

Operation
Colorado™ 1-Quad Zoom Tour User Manual Rev. 1 -9-
Menu Map
Main Level Programming Levels Description
STAT
RED
R.
000–255 Combines red, green, blue, and white to
make a custom color (0–100%)
GREN
G.
BLUE
B.
WHIT
W.
ZOOM
Z.
Changes the beam angle (Zoom)
STRB S. 00–20
Selects the strobe frequency
(0–20 Hz)
AUTO
AT.
01–10
P.
000–255
10 automatic programs and speed
PR.
01–10
10 customizable programs
RUN
DMX
DMX mode
SLAV
Slave mode
ADDR
D.
001–512
Selects the DMX starting address
PERS
TOUR
12-channel: RGBW, dimmer, strobe, color
macro, auto/custom, dimmer speed, auto
speed, zoom, zoom reset
TR16
17-channel: 16-bit RGBW and dimmer;
strobe, color macro, auto/custom, dimmer
speed, auto speed, zoom, zoom reset
STD.Y
17-channel: 16-bit RGBW and dimmer;
strobe, color macro, auto/custom, dimmer
speed, auto speed, zoom, zoom reset
FULL
25-channel: 16-bit RGBW pixel control and
dimmer; strobe, color macro, auto/custom,
dimmer speed, auto speed, zoom, zoom
reset
C1Q
10-channel: RGBW, dimmer, strobe, color
macro, auto/custom, dimmer speed, auto
speed **
ARC.1
3-channel: RGB control
AR1.D
4-channel: RGB, dimmer
ARC.2
4-channel: RGBW
AR2.D
5-channel: RGBW, dimmer
AR2.S
6-channel: RGBW, dimmer, strobe
AR2.Z
7-channel: RGBW, dimmer, zoom, zoom
reset
HSV
3-channel: HSV control
**Zoom locked to match Colorado™ 1-Quad series.

Operation
-10- Colorado™ 1-Quad Zoom Tour User Manual Rev. 1
Menu Map (Cont.)
Main Level Programming Levels Description
EDIT PR. 01–10 SC. 01–30
RED
000–
255
Combines red, green, blue, and white to
generate a custom color (0–100%)
GREN
BLUE
WHIT
ZOOM
Selects beam angle (zoom)
STRB 00–20
Selects the strobe frequency
(0–20 Hz)
TIME 000–
255
Defines the step duration
(slow to fast)
FADE
Defines the fade duration
(slow to fast)
SET
KEY
ON
Turns the passcode on or off
OFF
UPLD
****
(Enter
Passcode)
SEND/
END Uploads custom programs to other
COLORado™ 1-Quad Zoom Tour products
REST
****
(Enter Passcode)
Defaults product to factory settings
COLR
OFF
RGB set to 255 = max. output
RGBW
RGB set to 255 = balanced white
UC.
Universal color balance
DIMX
OFF
No dimmer
DIM1
Dimmer profiles fast (DIM1) to slow (DIM4)
DIM2
DIM3
DIM4
CURV
OFF
No dimmer
CV1
Dimmer curves fast (CV1) to slow (CV3)
CV2
CV3
DERR SAVE
Continues with last command upon loss of
DMX control
BLAK
Blacks out fixture upon loss of DMX
SLCK
OFF
SET main level access lock
ON
ZOOM BASE
Sets default zoom position
(full movement)
POS1
Sets position 1 setting for zoom limit
POS2
Sets position 2 setting for zoom limit

Operation
Colorado™ 1-Quad Zoom Tour User Manual Rev. 1 -11-
Menu Map (Cont.)
Main Level Programming Levels Description
CAL ****
(Enter
Passcode)
CAL1 WH.
01–11
RED
000–
255
Modifies the color macros used in the TOUR,
FULL, C1Q, TR16, and STD.Y personalities
GREN
BLUE
WHIT
CAL2
RED
Defines the color temperature used when
COLR is set to RGBW
GREN
BLUE
CALR
****
(Enter
Passcode)
Defaults CAL to factory settings
ZOOM
POS.1
P. 000–255 Sets the min/max position of the zoom function
POS.2

Operation
-12- Colorado™ 1-Quad Zoom Tour User Manual Rev. 1
Configuration
(Standalone)
Use standalone configuration to operate the product without a DMX controller.
Auto Programs
Auto programs allow for dynamic RGBW color mixing without a DMX controller.
1. Go to the AUTO main level.
2. Select the desired auto program (AT. 01–10) and speed of the program (P. 000–255) or
custom program (PR. 01–10).
You cannot edit any of the auto programs (AUTO 01–10); however, you can edit the
custom programs (PR.01–10). See Edit Custom Programs for details.
Edit Custom
Programs
This setting allows the programming of up to 30 scenes for each of the 10 customizable
programs, including colors and effects.
1. Go to the EDIT main level.
2. Select the desired custom program (PR. 01–10).
3. Select the desired scene (SC. 01–30).
4. Select the desired color, effect, or timer (RED, GREN, BLUE, WHIT, STRB, ZOOM, TIME,
or FADE).
5. Select the color, effect, or timer value (000–255 for colors, effects, and timers or 00–20 for
strobe).
6. Repeat for the other colors, effects, or timers.
7. Return to the scene (SC. 01–30) level.
8. Repeat the settings of colors, effects, and timers for the other scenes.
Master/Slave
The Master/Slave mode allows a group of Colorado™ 1-Quad Zoom Tours (the slaves) to
simultaneously duplicate the output of another Colorado™ 1-Quad Zoom Tour
(the master)
without a DMX controller.
1. Set each of the slaves:
a. Go to the RUN main level.
b. Select SLAVE.
2. Set the master:
a. Set the running mode to DMX as explained in DMX Control.
b. Select an auto or custom program as explained in Auto Programs, or a static mix of
colors.
•The master is the one that runs a program whether in Auto, Custom or Static Color
mode.
•Do not connect a DMX controller to the products configured for Master/Slave
operation. The DMX controller may interfere with signals from the master.
•The master should be the first product in the daisy chain.
Color Settings
The COLOR setting determines how the Colorado™ 1-Quad Zoom Tour generates the white
color based on various RGB settings.
1. Go to the SET main level.
2. Select COLR.
3. Select OFF, RGBW, or UC.
OFF:
When all the RGB faders are set to 255, the output is maximum, although
the resulting white color may not be balanced.
RGBW:
When all the RGB faders are set to 255, the resulting output is defined by
the configured white color (see White Calibration).
UC:
When all the RGB faders are set to 255, the output matches that of less
efficient products (Universal Color).

Operation
Colorado™ 1-Quad Zoom Tour User Manual Rev. 1 -13-
Dimmer Profiles
This setting determines how fast the output of the Colorado™ 1-Quad Zoom Tour changes
when you modify the values of the red, green, blue, white, and dimmer faders. This setting
provides four different op
tions to simulate the dimming curve of an incandescent lighting
product.
1. Go to the SET main level.
2. Select DIMX.
3. Select a dimmer curve (OFF, DIM1, DIM2, DIM3, or DIM4).
OFF:
The output is proportional (linear) to the dimmer and RGBW channel values.
DIM1–4:
The output follows the dimmer and RGBW channel values based on the
corresponding dimmer curve, DIM1 being the fastest and DIM4 the slowest.
Curve Settings
This setting allows you to select the dimmer curve shape using the red, green, blue, white, and
dimmer faders.
1. Go to the SET main level.
2. Select CURV.
3. Select a dimmer curve (OFF, CV1, CV2, or CV3).
OFF:
The output is proportional (linear) to the dimmer and RGBW channel values.
CV1–3:
The output follows the dimmer and RGBW channel values based on the
corresponding dimmer curve, CV1 being the fastest and CV3 the slowest.
For optimum control of the 16-bit dimming channels in the TR16, FULL, and STD.Y
personalities, be sure that both dimming curves in SET > DIM and SET > CURV are set to
OFF.
When the control panel lock is active, the product will prompt you to enter the passcode
after 30 seconds of control panel inactivity or after turning on the product. S
ee
Passcode.
Program Upload
This option allows you to copy the custom programs of one Colorado™ 1-Quad Zoom Tour onto
other Colorado™ 1-Quad Zoom Tour by using the Master/Slave mode.
1. Configure and connect the products in a Master/Slave arrangement, where the master has
the custom programs you want to transfer to the slaves.
2. From the master, go to the SET main level.
3. Select UPLD.
4. When PASS shows, press <ENTER>.
5. Enter the master access passcode as shown in Passcode.
6. When SEND shows, press <ENTER> to start the upload.
7. Wait for the upload process to finish (the display will show END before continuing or turning
the products off.
The master and slaves will provide the status of the process by lighting up as follows:
•Yellow indicates that the upload process is running.
•Green indicates that the upload process completed successfully.
•Red indicates that the upload process failed due to an error. Recheck all cable
connections and restart the process. If the issue persists, contact Chauvet Technical
Support.
DO NOT upload the data from a Colorado™ 1-Quad Zoom Tour to a different product. The
other product may become inoperative.
Reset
This setting allows you to reset the Colorado™ 1-Quad Zoom Tour
to the default values,
including the custom programs.
1. Go to the SET main level.
2. Select REST.
3. When PASS shows, press <ENTER>.
4. Enter the master access passcode as described in Passcode.
5. Wait for the reset process to finish.

Operation
-14- Colorado™ 1-Quad Zoom Tour User Manual Rev. 1
Whites Setting
This setting allows you to select and edit the temperature of the white colors used in channel 6
(Macros) when in the TOUR and C1Q mode, channel 11 when in the TR16 and STD.Y mode, or
channel 19 when in the FULL mode.
1. Go to the CAL main level.
2. Enter the master access passcode as described in Passcode.
3. Go to CAL1.
4. Select a white color (WH.01–11).
5. Select a color (RED, GREN, BLUE, or WHIT).
6. Select a color value (000–255).
7. Repeat for the other colors.
Whites Setting
Factory Reset
This setting allows you to reset to factory default the white colors used in channel 6 (Macros)
when in the TOUR and C1Q modes, channel 11 when in the TR16 and STD.Y
modes, or
channel 19 when in the FULL mode.
1. Go to the CAL main level.
2. Enter the master access passcode as described in Passcode.
3. Go to CALR.
4. Enter the master access passcode as described in Passcode again.
White Calibration
This setting allows you to select the white color shown by the Colorado™ 1-Quad Zoom Tour
when the color setting is RGBW and the DMX controller’s red, green, and blue faders are set to
255.
1. Go to the CAL main level.
2. Enter the master access passcode as described in Passcode.
3. Go to CAL2.
4. Select a color (RED, GREN, or BLUE).
5. Select a color value (000–255).
6. Repeat for the other colors.
When selecting CAL > CAL2, you will only be able to define the values of RED, GREN
(green), and BLUE.
The values of RED, GREN (green), and BLUE configured from CAL > CAL2 will define the
color temperature shown when the RGB faders are set to 255 if SET > COLR
> RGBW is
active.
Static Color
The Static Color mode allows for permanent RGBW color mixing without a DMX controller.
1. Go to the STAT main level.
2. Select the desired color or effect (RED, GREN, BLUE, WHIT, STRB, or ZOOM).
3. Select the color or effect value (000–255 for colors and effect, or 00–20 for strobe).
4. Repeat for the other colors or effects.

Operation
Colorado™ 1-Quad Zoom Tour User Manual Rev. 1 -15-
Configuration
(DMX)
Use DMX configurations to operate the product with a DMX controller.
DMX
Personalities
This setting allows you to choose a particular DMX personality.
1. Go to the PERS main level.
2. Select the desired personality (TOUR, TR16, STD.Y, FULL, C1Q, ARC.1, AR1.D, ARC.2,
AR2.D, AR2.S, AR2.Z, or HSV).
•See the DMX Values section for the highest starting address you can select for each
personality.
•Make sure that the starting addresses on the various products do not overlap due to
the new personality setting.
DMX Control
In this mode, each product will respond to a unique starting address from the DMX controller. All
products with the same starting address will respond in unison.
1. Select a DMX personality as shown in DMX Personalities.
2. Set the running mode:
a. Go to the RUN main level.
b. Select the DMX programming level.
3. Set the starting address:
a. Go to ADDR main level.
b. Select the starting address (001–512).
The highest recommended starting address for each DMX mode is as follows:
DMX
Personality DMX Address DMX Personality DMX Address DMX Personality DMX Address
TOUR
501
ARC.2
509
HSV
510
ARC.1
510
AR2.D
508
TR16
496
AR1.D
509
AR2.S
507
STD.Y
496
FULL
488
C1Q
503
AR2.Z
506
Loss Of Signal
Setting
This setting controls how the product will respond when the DMX signal is lost.
1. Go to the SET main level.
2. Select DERR.
a. Select SAVE to make the product use the last command used when the signal is lost.
b. Select BLAK to turn off the all the LEDs when the signal is lost.
Zoom Limit
Settings
These settings allow you to select the zoom range. Basic zoom (BASE) is the default setting
which allows the zoom to move at full range (000–255
) and has no adjustable limit. Position 1
(POS.1) and Position 2 (POS.2) allow you to set limits on how far the zoom moves.
1. Set the zoom range to be used:
a. Go to the SET main level.
b. Select ZOOM.
c. Select BASE, POS.1, or POS.2.
2. Set the limit for zoom range POS.1 or POS.2:
a. Go to the ZOOM main level.
b. Select POS.1 or POS.2.
c. Select a zoom limit value (P.000–255).

Operation
-16- Colorado™ 1-Quad Zoom Tour User Manual Rev. 1
DMX Values
TOUR
Channel Function Value Percent/Setting
1
Dimmer
000ó255
0–100%
2 Red
000ó255
0–100%
(Step Duration if Custom 1–10 in CH. 8 is active)
3 Green
000ó255
0–100%
(Fade Duration if Custom 1–10 in CH. 8 is active)
4
Blue
000ó255
0–100%
5
White
000ó255
0–100%
6 Color Macro + White
Balance
000ó010
011ó030
031ó050
051ó070
071ó090
091ó110
111ó130
131ó150
151ó170
171ó200
201ó205
206ó210
211ó215
216ó220
221ó225
226ó230
231ó235
236ó240
241ó245
246ó250
251ó255
No function
R: 100% G: 0–100% B: 0
R: 100%–0 G: 100% B: 0
R: 0 G: 100% B: 0–100%
R: 0 G: 100%–0 B: 100%
R: 0–100% G: 0 B: 100%
R: 100% G: 0 B: 100%–0
R: 100% G: 0–100% B: 0–100%
R: 100%–0 G: 100%–0 B: 100%
R: 100% G: 100% B: 100% W: 100%
White 1
White 2
White 3
White 4
White 5
White 6
White 7
White 8
White 9
White 10
White 11
7 Strobe
000ó009
010
ó
255
No function
0–20 Hz