Remember CHAUVET also provide a selection of effect dishes which are interchangeable for this unit.
Replacing Lamps
1. Disconnect from main power supply before attempting to replace either lamps or fuse.
2. Ensure that the unit is sufficiently cool, before removing blown lamps.
3. Never touch new lamps with your fingers; use a tissue or a cloth.
In order to replace the lamp, disconnect from main power supply first, and unscrew the lamp replacement
cover, which is highlighted on the diagram (fig.1). Only use the appropriately rated lamps as use of any
other lamp type may cause the unit to be non-operational.
Due to the nature of halogen lamps it is vitally important that you do not touch the new replacement lamp
with your fingers, as this will reduce lamp life considerably. Once again a tissue or cloth can be used for
fitting the replacement lamp.
Finally before using, check that the lamp is housed correctly in the lamp holder and that the lamp replace-
ment cover has been screwed back into place.
If after replacement of the lamp, the unit is still not working then please contact your dealer or CHAUVET
for servicing.
Replacing Fuses
If the unit does not function at all when connected to the main power supply i.e. the mechanism does not
spin. Then it is highly likely that the fuse has blown.
Disconnect from main power supply before attempting to replace either lamps or fuse.
In order to replace the fuse, disconnect from the main power supply first, and then unscrew the fuseholder
cover to reveal the fuse. The unit has a label attached which indicates the correct fuse rating and you will
also find this listed as part of the specifications for the unit later in this guide. It is most important that
replacement fuses are of the correct rating. Failure to use the correct fuse could damage the lighting effect
beyond economic repair.
The fuse should simply be placed inside the holder and the screw cap replaced, when this is done connect
to the main power supply to check. If the unit is still not working then please contact your dealer or
CHAUVET for servicing.
Cleaning
The most important part of your lighting effect to keep clean is the lens as it allows the light output to trans-
mit. This should be cleaned with a soft damp cloth. The body of the unit may also be cleaned in the same
way. We recommend internal cleaning be carried out by a fully qualified technician.
Maintenance & Servicing
Work on internal parts should be carried out by a qualified technician. Removal of covers other than the
front to replace lamp or effect dish, or the fuseholder is considered a breach of warranty and will not be
covered under any such agreement unless authorized first by the company.
Introduction
Congratulations on the purchase of your new CHAUVET lighting effect. We are confident you will enjoy
many trouble free hours with this unit. To assist with the care and use of the product we have prepared this
short guide.
Operation
Before connecting this unit to the mains power supply for the first time you must first install the lamps.
(See ‘Replacing Lamps’ for details).
This lighting effect has been designed to function on a mains power supply of either 120V~60Hz or
230V~50Hz and has been fitted with a suitable power plug for use with your local voltage. Check the label
and voltage selector switch (if fitted) on the unit and the power plug for the correct voltage.
When connected to the mains power supply the unit should illuminate. The unit will also begin to run
through its pre-programmed patterns. Some of these patterns are sound activated.
Due to the high operating temperature of halogen lamps it is advisable that the effect be used in well
ventilated areas taking care not to obstruct the air vents. After use allow time to ‘cool’ for safety and to
ensure lamp life before moving or touching.
The duty cycle for this effect should be no more than 15 minutes on then 15 minutes off.
Installation / Mounting
Although this unit can be used in an upright position, it is recommended that, for safety purposes, your
lighting effect be properly mounted using a suitable hanging clamp and safety cable. CHAUVET offers a
range of items, which are ideal for safe mounting.
Use in a well-ventilated area without obstruction to air vents.
Replacing Effect Dish
Disconnect from main power supply before attempting to replace effects dish.
Simply remove top cover which will reveal the lamps, holders and dishes. The cover is removed by
unscrewing four screws on the top and each side. The dish is held in place with two small screws, which
when removed allow the dish to be manipulated from the motor shaft. Replace with chosen effect dish,
tighten screws and replace cover.
At the Rear:
• Screw Cap Fuseholder • Mounting Bracket
• Fan
• Lamp Replacment Cover
• Lenses
Fig. 1
