Child Craft F50001 User manual

1
AB20030_G1A
AB20030_G2B
Assembled as a Crib
Assembled as a Twin Size Bed
Foundations®Worldwide, Inc.
5216 Portside Dr, Medina Oh 44256 USA • PH: 1 330.722.5033 • FAX: [phone]
www.childcraftbaby.com
London Euro Compact Size Crib
ASSEMBLY ASSISTANCE
IMPORTANT: retain for future reference read
carefully.
Foundations®strives for the highest quality in our
products but occasionally a missing part or problem
can occur during assembly.
If any parts are missing or broken or you need
assistance with assembly, DO NOT return the
product to your dealer. Go to our website at
www.childcraftbaby.com or Call Foundations
®for
assistance at 1-877-716-2757 (U.S. Only) or
1-330-722-5033 (Monday through
Friday, 9:00 a.m.– 4:00 p.m. Eastern Time). Please
have the model number and manufacture date
available when you call or write us at:
Foundations®, 5216 Portside Dr. Medina Oh. 44256
Read all instructions BEFORE assembly and USE of product.
KEEP INSTRUCTIONS FOR FUTURE USE.
FOR CUSTOMER SERVICE CALL
1-877-716-2757
(outside of U.S. 330-722-5033). DO NOT CALL
RETAILER OR RESELLER FOR SERVICE
AS THEY ARE NOT AUTHORIZED TO
RESOLVE ANY SERVICE ISSUES.
FOR FEDERAL SAFETY STANDARD
COMPLIANCE CERTIFICATES, PLEASE VISIT
OUR WEBSITE AT
www.foundations.com
Record the information for your product here:
Model number:
Manufacture date:
PO number:
• Adult assembly required.
• Read all instructions BEFORE assembly and USE
of product. KEEP INSTRUCTIONS FOR FUTURE
USE.
• Unpack carton, remove packing materials,
including poly bag. Identify and check all parts.
ASSEMBLY INSTRUCTIONS
THIS IS THE ASSEMBLY INSTRUCTIONS FOR CRIBS SOLD IN THE UNITED STATES
AB20030E
Models Covered: F50001

2
A. 4mm Allen Wrench
B. Flat Washer
C. Spring Bracket (Left)
D. Spring Bracket (Right)
E. Flat Head Machine Screw
F. 6mm Connector Nut
G. 6mm x 40mm Allen Head Bolt
H. 6mm x 14mm Allen Head Bolt
I. 6mm Connector Nut
J. 6mm x 70mm Allen Head Bolt
K. Stationary Side Assy
L. End Panel Footboard
M. End Panel Headboard
N. Spring
O. Mattress
AB20030_G3A
A
BCD
EF
I
H
J
G
Hardware Package
AB20030_G4A
L
N
K
M
O
Crib Parts
PARTS LIST
Part Description Part Number Quantity
11200070
11200081
11200074
11200075
11200356
11200331
11200362
11200328
11200330
11200332
22300903
22300910
22300998
11200345
21100037
2
4
2
2
4
20
8
12
8
8
2
1
1
1
1
PREPARATION
Carefully remove and lay out all hardware and parts.
Check quantities and match the parts list. Construct
Note: during the assembly process whenever
using screws or bolts, Check each with the parts list
or bolt on the diagram of the item which is sketched
in the assembly directions. If any parts are missing
or broken or you need assistance with assembly
DO NOT return your product to the dealer.
Please identify the London Euro crib by the model
the Stationary Sides Assemblies when you call or
write to Foundations®. Make note of all
identification numbers and include this information
with your request.
DO NOT Substitute Parts!
Note:
Do Not discard spare parts as they may be used for
Note: Items I and J will only be needed if Crib is
converted to a Twin Bed after the Crib is no longer
needed. Save for future use.
SUGGESTED TOOLS
#2 Medium Straight Screwdriver

3
STEP 1
Figure 1
Attach Spring Bracket-Right (D) and Spring
Bracket-Left (C) to Spring (N) using a Flat Head
Machine Screw (E), a Flat Washer (B) and a
Connector Nut (F).
Note: Each Flat Head Machine Screw (E) has a
friction enhancing patch applied to the thread which
will cause some resistance during the tightening
process.
Tighten each bracket until it is secure, but allows
the bracket to be easily rotated by hand. Place each
bracket at a 45º angle as shown.
See Figure 1.
AB20030_G5A
N
C
C
D
D
Pouches are on top
surface with printed
text facing up.
Top surface
shown up.
Bottom surface
shown up.
See enlarged
view.
C
D
45°
D
E
B
F

4
Figure 3
STEP 3
AB20030_G7
G
L
F
Assembly
from Step 2.
FG
Attach an End Panel Footboard (L) to the opposite
side of Stationary Side Assembly (K) using two (2)
of Connector Nuts (F) and two (2) Allen Head Bolts
(G) as shown in diagram. Tighten securely using
Allen Wrenches (A).
See Figure 3.
STEP 2
Figure 2
AB20030_G6A
F
F
G
M
K
G
Attach an End Panel Headboard (M) to a Stationary
Side Assembly (K) using two (2) of Connector Nuts
(F) and two (2) Allen Head Bolts (G) as shown in
diagram. Tighten securely using Allen Wrenches
(A).
See Figure 2.

5
STEP 4
Figure 4 AB20030_G8
G
F
K
Gand Fare
shown installed
on this assembly.
F
G
Attach the second Stationary Side Assembly (K)
following the same process described in earlier
steps. Use a total of four (4) Connector Nuts (F)
and a total of four (4) Allen Head Bolts (G). Tighten
all areas securely using Allen Wrenches (A).
See Figure 4.
Figure 5
STEP 5
AB20030_G9A
H
Follow this
process to
install an
Allen
Bolt H
at each
of the four
corners of
Spring
Assembly N.
Pouches are on top
surface with printed
text facing up.
.
Assistance by a second person is recommended for
this step.
There are two (2) possible height locations for
Spring Assembly (N). Select the height which is
appropriate for the child. Refer to warning before
installation for additional information. Angle Spring
Assembly (N) (from Step 1) carefully down into crib
as shown in upper diagram.
Attach all four (4) Brackets (C) and (D) at the same
height as shown in lower diagram. Allen Head Bolts
(H) will thread into a factory installed threaded
insert. Tighten each Allen Head Bolts (H) securely
with Allen Wrenches (A).
To adjust height of Spring Assembly (N), remove
all four (4) Allen Head Bolts (H). Then move Spring
(N) to the other height adjustment location. Reinstall
Allen Head Bolts (H) at this location following the
same process outlined in this step above.
See Figure 5.

6
Figure 7
STEP 7
AB20030_G11A
O
Before installing Mattress (O), read all warning and
information on maintenance on pages 7 and 8.
Crib is now ready for use.
Figure 6
STEP 6
AB20030_G10
H
H
F
F
Install two (2) Connector Nuts (F) and two (2) Allen
Head Bolts (H) in each post on End Panel (L) as
shown. Tighten securely using Allen Wrenches (A).
See Figure 6.

7
Twin Bed Conversion
Figure 8
AB20030_G12A
End Panel Headboard M
(now becomes
Twin Bed Headboard)
Flat edge will face
outward.
Bed Rail Kit
(purchased separately)
End Panel Footboard L
(now becomes
Twin Bed Footboard)
Curved edge will face
outward.
Allen Bolt Hand
Connector Nuts F
can be used to fill the
empty holes where
Stationary Side Assembly
Khad been attached.
Install one of each item
from opposite sides of
posts and thread items
together securely with
Allen Wrenches A.
Allen Bolts Jwill attach
Bed Rails (two (2) at
each post).
These bolts will thread into
Joint Connector Nuts Iwhich
will be installed inside face
of Bed Rail.
If the crib is no longer needed for the child, then
this crib can be converted to a Twin Size Bed. To
complete the conversion, a Bed Rail kit must be
purchased from Foundations.
The crib should be disassembled with all parts
stored away except for the following:
1 End Panel Footboard (L)
1 End Panel Headboard (M)
8 Joint Connector Nuts - 6 mm (I)
8 6mm Allen Head Bolts (J)
Follow the assembly process outlined in the
assembly instructions included with the Bed Rail kit.
Maintenance Cleaning and Storage
MAINTENANCE:
Upon completion of the assembly, check to make sure all screws, bolts and connectors are tightened and
secure.
Periodically check crib for damaged hardware, loose joints, missing parts or sharp edges before and after
assembly and frequently during use.
DO NOT use crib if any parts are missing or broken.
If any parts are missing, broken or you need Assistance DO NOT return crib to your dealer.
Call Foundations® at 330.722.5033 and include model identication numbers recorded on page 1.
DO NOT substitute parts.
CLEANING:
Mix a mild solution of gentle dish washing soap and water, apply to surface using a clean cloth lightly
dampened in the solution. Rinse well with clear water using a soft clean cloth, then dry all surfaces with a
soft dry cloth.
DO NOT use abrasive cleaners or any cleaners with harsh chemicals that would contact a child’s
skin, scouring pads, steel wool or coarse rags. This crib should be treated the same as any ne
furniture.
STORAGE:
When storing crib use Caution as extreme temperature or humidity changes could be harmful.
Use caution when a vaporizer is in use. Always aim vapor stream away from crib as well as away
from any wood furniture item.
After completing the assembly the user is advised to read and be aware of
ALL WARNINGS, CAUTIONS, CLEANING, STORAGE USE AND MAINTENANCE notices in these
directions and printed on the storage pouch on the crib spring. A printed pouch is attached to the
crib spring for the permanent storage of the assembly directions. Please place the complete set of
assembly directions into the pouch for future referral. We caution the user to Not place excess
hardware in the pouches as it could present danger to the child if retrieved.

8
Meets CPSC
Safety Requirements
5216 Portside Dr.
Medina Ohio 44256 USA
Telephone: [phone]
Fax: [phone]
www.childcraftbaby.com
Failure to follow these warnings and the instructions could result in serious injury or death!
WARNING:Infants can suffocate.
• In gaps between a mattress too small or too thick and sides of crib.
• On soft bedding.
• NEVER add a mattress, pillow, comforter or padding.
• The crib, including side rails, must be fully erected prior to use.
• Make sure latches are secure (if your crib either folds for storage or transport or has a moveable side for
easy access to child).
• Strings can cause strangulation! NEVER place items with a string around a child’s neck such as hood
• Discontinue use of the crib when child is able to climb out or reaches the height of 35 inches (89 cm).
• Child can become entrapped and die when improvised netting or covers are placed on top of product.
NEVER add such items
• When child is able to pull to standing position, set mattress to lowest adjustment position and remove
bumper pads, large toys, and other objects that could serve as steps for climbing out.
• NEVER place crib near window where cords from blinds or drapes can strangle a child.
• Replace teething rail if damaged, cracked or loose (if equipped with teething rails).
• Use ONLY the mattress provided by the manufacturer (which must be at least 37-3/4 inches (96 cm) long by 23-3/4
inches (60.4 cm) wide and not more than 3 inches (7.6 cm) thick.
• Always provide the supervision necessary for the continued safety of your child. When used for playing,
NEVER leave child unattended.
• To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on their back to sleep,
unless otherwise advised by your physician.
• NEVER use this product if there are any loose or missing fasteners, loose joints, broken parts, or torn
mesh/fabric. Check before assembly and periodically during use. Contact Foundations for replacement
parts. Never substitute parts.
• NEVER leave child in crib with side lowered. Be sure side is in raised and locked position whenever child
is in product (if your crib has a moveable side).
•
purpose. They can cause suffocation.
• NEVER use a water mattress with this crib.
•
• DO NOT use crib near objects that child could reach or pull into crib and cause injury such as lamps,
•To avoid injuries, do not allow children to climb or play on or under the crib.
WARNINGS