Childcare 025031 User manual

IMPORTANT:
RETAIN FOR FUTURE REFERENCE,
READ CAREFULLY
Jump‘N’Play
Activity Centre
Model # 025031

2
Read all instructions before assembly and use of the activity centre.
Keep instructions for future use since it contains important information.
SAFETY PRECAUTIONS
BEFORE ASSEMBLINGTHIS ACTIVITY CENTRE,READ AND UNDERSTANDTHE INSTRUCTIONS.
Fall hazard; child’s activity may move activity jumper.Use only on oor.To avoid tip over,place
product on a at,level surface. Never use this product on an elevated surface,eg.A table.
Strangulation hazard; strings can cause strangulation! Do not place items with a string around
child’s neck,such as hood strings or pacier cords.
Do not suspend strings over product or attach strings to toys.
Possible entanglement or strangulation injury when toys are attached to activity centre.
Do not tie together with other toys.
Remove all packaging and fasteners before use.
Begin using the product when the child can hold their head up unassisted up to a maximum
weight of 12 kg and discontinue using the product as a stationary activity centre when the
child begins to walk unassisted.
Never leave the child unattended.
Always keep child in view while in product.
Ensure the child is correctly and safely positioned in the seat of the baby bouncer.
Never use near stairs.
Do not let children play with this product.
Do not move or lift this product with the baby inside it.
Do not use if any components are broken or missing.
Do not use the activity centre as a swing.
Do not allow other children to play near the activity centre.
KEEP INSTRUCTIONS IN A SAFE PLACE FOR FUTURE REFERENCE.
KEEP PLASTIC COVERING AWAY FROM CHILDRENTO AVOID SUFFOCATION.
WARNING
Age range suitability:6 months / 12 kg.
Make sure all the locking equipment is installed well before using the activity centre.
DO NOT use the activity centre on a rough surface to avoid any injury to the infant.
DISCONTINUE USE of activity centre when the child begins to walk unassisted.Maximum weight 12 kg.
This activity centre does not replace a cot or a bed.Should your child need to sleep,then it should be placed in a suitable
cot or bed.
A time limit of 20 minutes per use is recommended for the child to be in the activity centre.
DO NOT use accessories or replacement parts other than those approved by the manufacturer.
The toy should be assembled by an adult.

3
SAFETY PRECAUTIONS
Do not mix old and new batteries.
Do not mix alkaline,standard (carbon-zinc) or rechargeable (nickle-cadmium) batteries.
Adult supervision is required when charging rechargeable batteries.
Always remove at or exhausted batteries from the toy.
Do not short circuit the supply terminals.
Non-rechargeable batteries are not to be recharged
WARNING
Battery Safety Information
In exceptional circumstances,batteries leak uids that can cause a chemical burn injury or ruin your
product.To avoid leakage:
• DO NOT mix old and new batteries or batteries of different types:alkaline,standard (carbon zinc) or
rechargeable (nickle-cadmium).
• Insert batteries as indicated inside the battery compartment.
• Remove batteries during long periods of non-use.
• ALWAYS remove exhausted batteries from the product.
• Dispose of batteries safely.
• DO NOT dispose of this product in a re.The batteries inside may explode or leak.
• Never short-circuit the battery terminals.
• Use only batteries of the same equivalent type,as recommended.
• DO NOT charge non-rechargeable batteries.
• Remove rechargeable batteries from the product before charging.
• If removable,rechargeable batteries are used,they are only to be charged under adult supervision.
• Batteries are to be inserted with the correct polarity.

4
Due to variations in the style and design of our products, the photographs and illustrations shown in this
instruction manual are generic,therefore product fabrics,colour and design may vary from images shown.
CNP Brands reserves the right to alter product specications without notice as a result of our ongoing
policy of product improvement.
Contents
Assembly contents list
Assembly / Operating instructions
How to care for your Jump‘N’Play Activity Centre
Congratulations on your purchase of the Jump‘N’
Play Activity Centre
This product has been designed and developed with safety,
comfort and functionality in mind. Please take the time to read
this manual carefully before using this product and keep it in a
safe place for future reference.
CONGRATULATIONS

5
ASSEMBLY CONTENTS
Check what you have received...
You have received 1 box. Please check the contents of the
box against the list below. If anything is missing, please contact
Customer Service.
InAustralia,contact CNP Brands on 1300 667 137,in New Zealand
contact Wainhouse Distribution on 0800 567 5000.
Supplied loose in box:
Top Tray x 1
x 3
x 1
x 1 x 1
x 1
x 3
x 1
Base Frame
Music and lights
module
Rod and Ball Toy Floor Mat
Spinning Ball Toy
& Clips
Legs
Seat
(with Seat Pad
pre-assembled)

6
ASSEMBLY CONTENTS
x 1
Leg Toys
There are no accessories recommended for use with this Childcare Activity Centre.
Check what you have received...
You have received 1 box. Please check the contents of the
box against the list below. If anything is missing, please contact
Customer Service.
InAustralia,contact CNP Brands on 1300 667 137,in New Zealand
contact Wainhouse Distribution on 0800 567 5000.
Supplied loose in box:
You will require:
x 1 x 3
Phillips
Screwdriver
(Not Included)
AAA Batteries
(Not Included)

7
ASSEMBLY / OPERATING INSTRUCTIONS
To assemble Activity Centre frame...
1
2
3
4
5
Connect the 3 x Base Frames,making sure the
push pins are located in the holes and secure
correctly.
Manually rotate the small White feet to ensure
they are sitting at on the oor.
Insert 3 x Legs into the leg housings on the Base
Frame until secure.
Lay the Floor Pad inside the Base Frame.
Secure the Floor Pad to the Base frame via the
6 x Velcro Straps.
Whilst holding the Top Tray, feed a Leg strap end
through the slot in the Top Tray and secure into
the rst height setting on the underside of the
Top Tray.
Push the webbing inside the slot between
the height adjustment settings to ensure the
webbing is held well.
Repeat for the remaining 2 x Legs straps until
Top Tray is secure at all three points.
Insert Seat into the Seat hole in the Top Tray.
Push down until Seat is connected and secure.
1a.
1b.
2a.
3a.
3b.
4a.
4b.
5a.
5b.
NOTE: All 3 x Leg Straps must be on the same
height setting.
NOTE: Seat should now be able to rotate 360°.

8
ASSEMBLY / OPERATING INSTRUCTIONS
To assemble Music & Lights Module...
To use Music & Lights Module...
1Turn Music and Light Module over and
unscrew the battery cover.
Insert 3 x AAA batteries (sold separately).
Replace battery cover by screwing back
into place.
1a.
1b.
1c.
IMPORTANT! Please note that a screwdriver (not included) is
required to access the Battery Pack to insert 3 x AAA Batteries
(sold separately).
2
1
Position the Music and Light Module into the
opening on the Top Tray.
Push and twist the locking levers on the
underside of the Top Tray Frame to secure.
Turn on Music and Light Module with the ON/
OFF button.
Press a button to start the music and lights.
Pressing any button will change music
selection.
Turn off Music and Light Module with the ON/
OFF button.
2a.
2b.
1a.
1b.
1c.
1d.
Do not mix old and new batteries.
Do not mix alkaline,standard (carbon-zinc) or rechargeable (nickle-cadmium) batteries.
Adult supervision is required when charging rechargeable batteries.
Always remove at or exhausted batteries from the toy.
Do not short circuit the supply terminals.
Non-rechargeable batteries are not to be recharged
WARNING

9
ASSEMBLY / OPERATING INSTRUCTIONS
To assemble Assorted Toys...
To operate Seat Height Adjustment...
1Insert the Spindle Ball Toy into the housing on
the Top Tray.
Secure Spindle Toy in place by assembling
the 2 x Spindle Ball Clips over the ends of the
Spindle Toy.
1a.
1b.
2
1
Insert the Rod & Ball Toy into the designated
slots in the Top Tray.
Insert 3 x Leg Toys into the slots in the top of the
Legs.
There are two height adjustments that are
changed by altering the position of the
connectors on the underside of the Seat Tray.
2a.
2b.
1a.

10
ASSEMBLY / OPERATING INSTRUCTIONS
To operate Seat Height Adjustment continued...
To remove Seat Pad from Seat...
2
1
To adjust,remove the strap end from the current
height setting and re-secure in the higher
height setting.
Push the webbing inside the slot between
the height adjustment settings to ensure the
webbing is held well.
Repeat this step for the remaining 2 x seat strap
ends.
Remove the Seat from the Top Tray by pushing
the Seat out from the underside of the Tray.
Un-hook the Seat Pad from the hooks on the
Seat ring.
After washing,re-hook the Seat pad onto the
hooks of the Seat ring.
Re-insert Seat into the Seat hole in the Top Tray.
Push down until Seat is connected and secure.
Carefully check that Seat pad is correctly
secured to the Seat ring before placing child
into the Activity Centre.
2a.
2b.
1a.
1b.
1c.
1d.
1e.
1f.
NOTE:The child’s toes should touch the oor.
If your child’s feet don’t touch the oor,the
seat height setting is too high. If your child’s
feet are sitting at on the oor,the seat height
setting is too low.

11
HOW TO CARE FOR YOUR CHILDCARE ACTIVITY CENTRE
Cleaning
Maintenance
To ensure the long-lasting use of your activity centre, dry it with a
soft absorbent cloth after use. Use a damp cloth to clean the
frame. Do not use abrasive cleaners.Allow it to dry completely
before storing it away. Do not dry clean, or use bleach on fabrics
or trims. Do not machine wash, tumble or spin dry, unless the care
labelling on the product permits these methods.
Check activity centre regularly to ensure that locking devices and
components are secure and working properly.Always check parts
regularly for tightness of screws, nuts and other fasteners – tighten or
replace if required.To maintain the safety of your activity centre, seek
prompt repairs for bent, torn,worn or broken parts. Use only those
parts and accessories approved by CNP Brands.
If you have any difculties in assembling the activity centre, please
contact our Service Department.
In Australia, contact CNP Brands on 1300 667 137, in New Zealand
contact Wainhouse Distribution on 0800 567 5000.
Warranty
For all warranty terms and conditions, please visit cnpbrands.com.au

12
ABOUT US
About CNP Brands
Currently,CNP Brands boasts one of the most diverse brand portfolios
with a combination of company owned brands and distribution
agreements.
Our own brands,including Childcare,have gone from strength to
strength in recent years.Childcare,and our premium brand bebe
care, demonstrate our commitment to quality and continuing
investment in product development.

13
Distributed in Australia by CNP Brands
82 Maribyrnong Street, Footscray,VIC, 3011
Customer Service 1300 667 137
W: www.cnpbrands.com.au
E: [e-mail]
F: www.facebook.com/CNPBrands
I: @cnp_baby
Distributed in New Zealand by Wainhouse
Distribution
2-6 Argyle St, Morningside,
PO Box 41-014,
St Lukes,Auckland, New Zealand
Customer Service: 0800 567 5000
E: [e-mail]