Childcare Vibe 'N' Swing User manual

IMPORTANT:
RETAIN FOR FUTURE REFERENCE,
READ CAREFULLY
Vibe‘N’Swing
Model # 037725

2
Read all instructions before assembly and use of the swing. Keep
instructions for future use.
SAFETY PRECAUTIONS
Make sure all the locking equipment is installed well before using the swing.
DO NOT use the swing on any rough surface to avoid any injury to the infant.
DISCONTINUE USE of swing when infant attempts to climb out.
DISCONTINUE USE of swing when infant can roll over.
NEVER use the toy-bar to carry the swing.
Age range suitability:Birth to 9kgs.
This swing DOES NOT replace a cot or a bed.Should your child need to sleep, then they should be placed in a suitable
cot or bed.
DO NOT use accessories or replacement parts other than those approved by the manufacturer.
To avoid injury ensure that children are kept away when unfolding and folding this product.
BEFORE ASSEMBLINGTHIS SWING,READ AND UNDERSTANDTHE INSTRUCTIONS.
Never leave the child unattended.
Never use this product on an elevated surface,eg. A table.
This swing is not intended for prolonged periods of sleeping.
Always use the restraint system.
Do not use the swing once your child can sit unaided.
Do not let children play with this product.
Do not move or lift this product with the baby inside it.
Do not use if any components are broken or missing.
KEEP INSTRUCTIONS IN A SAFE PLACE FOR FUTURE REFERENCE.
The toy shall be assembled by an adult.
WARNING

3
Battery Safety Information
SAFETY PRECAUTIONS
In exceptional circumstances,batteries leak uids that can cause a chemical burn injury or ruin your product.To avoid
leakage:
• DO NOT mix old and new batteries or batteries of different types:alkaline,standard (carbon zinc) or rechargeable
(nickle-cadmium).
• Insert batteries as indicated inside the battery compartment.Batteries are to be inserted with the correct polarity.
• Remove batteries during long periods of non-use.
• ALWAYS remove exhausted batteries from the product.
• Dispose of batteries safely.
• DO NOT dispose of this product in a re.The batteries inside may explode or leak.
• Never short-circuit the battery terminals.
• Use only batteries of the same equivalent type and polarity,as recommended.
• DO NOT charge non-rechargeable batteries.
• Remove rechargeable batteries from the product before charging.
• If removable,rechargeable batteries are used,they are only to be charged under adult supervision.
• Batteries are to be inserted with the correct polarity.

4
Due to variations in the style and design of our products, the photographs and illustrations shown in this
instruction manual are generic,therefore product fabrics,colour and design may vary from images shown.
CNP Brands reserves the right to alter product specications without notice as a result of our ongoing
policy of product improvement.
Contents
Assembly contents list
Assembly / Operating instructions
How to care for your Vibe ’N’Swing
Congratulations on your purchase of the Childcare
Vibe ’N’Swing
This product has been designed and developed with safety,
comfort and functionality in mind. Please take the time to read
this manual carefully before using this product and keep it in a
safe place for future reference.
CONGRATULATIONS

5
ASSEMBLY CONTENTS
Check what you have received...
You have received 1 box. Please check the contents of the
box against the list below. If anything is missing, please contact
Customer Service.
InAustralia,contact CNP Brands on 1300 667 137,in New Zealand
contact Wainhouse Distribution on 0800 567 5000.
Supplied loose in box:
Seat Pad
(with Harness
pre-assembled)
x 1
x 1
x 1
x 1 x 4
x 1
x 1
x 2Left Frame
Seat Backrest
Tube (Longer)
Toy Bar
(with 2 X Toys
pre-assembled)
Screws
Seat Footrest
Tube (Shorter)
Right Frame
(with control
module
preassembled)
Foot Tube
There are no accessories recommended for use with this Swing.

6
ASSEMBLY CONTENTS
Check what you have received...
You have received 1 box. Please check the contents of the
box against the list below. If anything is missing, please contact
Customer Service.
InAustralia,contact CNP Brands on 1300 667 137,in New Zealand
contact Wainhouse Distribution on 0800 567 5000.
You will require:
Phillips Head
Screwdriver
(Not supplied)
x 1 x 4
AA Batteries
(Not supplied)
There are no accessories recommended for use with this Swing.

7
ASSEMBLY / OPERATING INSTRUCTIONS
To assemble Swing frame...
2
3
Slide the Seat Backrest Tube (longer of the two
seat tubes) through the loops of the harness at
the top of the Seat Pad underside.
Ensure the tube is sitting inside the rear fabric
ap of the Seat Pad.
Ensuring the Seat Pad is facing upward,insert
the Seat Pad with Seat Backrest Tube into the
Swing,ensuring the assembly holes of the seat
tube align with the screw holes on the inside of
the swing arm housing.
Secure Seat Backrest Tube to the swing arm
housing using 2 x screws and a Phillips Head
Screwdriver (not supplied).
2a.
2b.
2c.
3a.
1
Insert one Foot Tube into the bottom of the front
leg of both the Right and Left Frames until it
clicks into place.
Insert the remaining Foot Tube into the bottom
of the rear leg of both the Right and Left
Frames until it clicks into place.
Open the legs of the Right and Left Frames out
completely until they click into place.
1b.
1c.
1a.

8
ASSEMBLY / OPERATING INSTRUCTIONS
To assemble Swing frame continued...
To power Swing...
4
5
6
1
Align the assembly holes of the Seat Footrest
Tube with the screw holes on the inside of the
swing arm housing.
Assemble Seat Footrest Tube to the swing arm
housing in an upright position using 2 x screws
and a Phillips Head Screwdriver (not supplied).
Do not tighten completely.
Gently pull the bottom of the Seat Pad over the
Seat Footrest Tube.
Lower Seat Footrest Tube to the correct position.
Tighten screws completely.
Align the Toy Bar with the mounting pegs at the
top of the swing arms.
Push Toy Bar down onto pegs to secure.
Using a Phillips Head Screwdriver (not supplied)
unscrew the battery compartment cover.
Insert 4 x AA batteries.
Replace battery compartment cover,ensuring
screw is tight and cover is secure.
4a.
4b.
5a.
5b.
5c.
6a.
6b.
1a.
1b.
1c.
Note: Repeat steps 1a-1c to remove or replace
exhausted batteries.

9
ASSEMBLY / OPERATING INSTRUCTIONS
To operate Swing...
Hold button for 3 seconds to turn swing on/off.
When the swing is turned on, the swing function will begin
automatically on the 3rd swing speed,the music/melodies
will also begin to play.
Press button to cycle through music/melodies.
Cycle through music/melodies completely to turn sound off.
(Note: There are 6 music/melodies)
Press button to change swing speed.
When pressed, light will ash Red,Green,Red (changing
swing speed mode),followed by green ashes indicating
the swing speed.
Eg.4 green ashes in a row indicates the 4th swing speed
has been selected.
(Note: There are 5 swing speeds)
One press will set timer for 10 minutes.
Two presses will set timer for 15 minutes.
Three presses will set timer for 30 minutes.
(Note: For power saving,the Swing will turn off
automatically after 45 minutes).
Power/Music Button:
Power/Music Button:
Swing Button:
Timer Button:
Do not mix old and new batteries.
Do not mix alkaline,standard (carbon-zinc) or rechargeable (nickle-cadmium) batteries.
Adult supervision is required when charging rechargeable batteries.
Always remove at or exhausted batteries from the toy.
Do not short circuit the supply terminals.
Non-rechargeable batteries are not to be recharged.
Batteries are to be inserted with the correct polarity.
WARNING

10
1
2
Release the harness buckle.
Place child into the swing.
Place crotch pad up and between child’s legs.
1a.
1b.
2a.
ASSEMBLY / OPERATING INSTRUCTIONS
3
4
5
Feed child’s arms through the shoulder strap/waist
strap loop.
Insert combined shoulder and waist strap clips into
harness buckle.
Secure crotch pad ap down and over harness
buckle.
Tighten the adjusters on the waist straps to ensure
the harness is secure.
To release the harness buckle,push the buckle
release button.
3a.
3b.
3c.
4a.
5a.
To use the Harness...
CAUTION: Always adjust the harness when
changing the seating position of the child.