Childcare FASTWAY 089345 User manual

IMPORTANT:
RETAIN FOR FUTURE REFERENCE,
READ CAREFULLY
FASTWAY
GATE
Model #089345
630 - 1080mm 774mm

This gate is designed for children from Birth to 24 months. Since each
child’s skills develop at different ages, these parameters should be
monitored against your child’s own development.
Read all instructions before assembly and use of the safety gate. Keep
instructions for future use.
Intended for use with children from Birth through 24 months.
Check the stability of the gate and tighten all hardware and mountings regularly.
To prevent serious injury or death, securely install gate or enclosure and use according to
manufacturer’s instructions.
Install according to the manufacturer’s instructions.
NEVER use with a child able to climb over or dislodge/open the gate or enclosure.
NEVER use if gate is less than 3/4 of child’s height.
DO NOT use if any part of the gate is broken or missing.
This product will not necessarily prevent all accidents.Never leave child unattended.
Use only spare parts available from cnp brands.
NEVER allow child to climb or swing on gate.
Use only with the locking/latching mechanism securely engaged.
Discontinue use if any part of the gate is damaged.
NEVER climb over the gate.
NEVER hang or tie toys,etc,to any part of the gate.
SAFETY PRECAUTIONS
WARNING
Due to variations in the style and design of our products, the photographs and illustrations shown in this
instruction manual are generic,therefore product fabrics,colour and design may vary from images shown.
CNP Brands reserves the right to alter product specications without notice as a result of our ongoing
policy of product improvement.
Contents
Assembly contents list
Assembly / Operating instructions
How to care for your Fastway Gate
Congratulations on your purchase of the Fastway
Gate.
This product has been designed and developed with safety,
comfort and functionality in mind. Please take the time to read
this manual carefully before using this product and keep it in a
safe place for future reference.
CONGRATULATIONS

ASSEMBLY CONTENTS ASSEMBLY CONTENTS
Check what you have received...
You have received 1 box. Please check the contents of the
box against the list below. If anything is missing, please contact
Customer Service.
InAustralia,contact CNP Brands on 1300 667 137,in New Zealand
contact Wainhouse Distribution on 0800 567 5000.
Supplied loose in box:
Hinge side
Template (A)
Locking side
template (B)
Wood screws (K)
Lower hinge
spindle (D)
Lower latch
bracket (M)
Lower hinge cap
(F)
Locking latch
spindle (N)
Upper hinge
spindle (H)
Wrench (P)
x 1
x1
x 1
x 1
x 1
x 1
x 1
x 4
x 1
x 2
x 1
x 1
x 2
x 1
x 2
Lower hinge
bottom (C)
Locking latch
bracket (L)
Spring (E)
Upper hinge (G)
Stop pin (O)
Screw/Screw
socket (I-J)
There are no accessories recommended for use with this Childcare Fastway Gate.
Supplied loose in box continued:

ASSEMBLY / OPERATING INSTRUCTIONS
To install Safety Gate...
1
2
Important: Gate must be installed in a structurally
sound opening.
The hinge side of gate must be mounted to a rigid
surface.
Ensure mounting surface (wall,door frame,stairposts,
etc.) is strong, rigid and has an even surface.
If using gate on a stairway, it must be placed either on
top stair or on lowest stair at the bottom.
1a.
1b.
1c.
2a.
ASSEMBLY / OPERATING INSTRUCTIONS
To install Safety Gate (continued)...
3
4
5
6
6
The correct width will be achieved by adjusting gate
sections and all four corner spindles.
Each spindle adjusts individually and may be
extended varying lengths to allow for moulding,
uneven walls,etc.
Spindles may be extended a minimum of 32mm
(hinge side) or 25mm (on locking side) and a
maximum of 70mm.
Finding appropriate width of gate
Adjust sections until gate is approximately the correct
width and adjustment holes are aligned and overlap
in two places on both the top and bottom rail
(maximum overlap is 5 bars).
Sections should t without any distance between rails
or bars.
Place screws (I) and screw sockets (J) in top and
bottom sets of overlapping adjustment holes nearest
hinge and locking sides of gate.
Do not fully tighten yet.
Screw upper hinge spindle (H) into top rail of one gate
section.
Screw lower hinge spindle (D) into bottom rail of same
side.
Extend spindles equally.
Screw locking latch spindles (N) into top and
bottom rails of second gate section.
Extend spindles equally.
Final spindle adjustments will be made later.
3a.
3b.
3c.
4a.
4b.
4c.
5a.
5b.
6a.
6b.
6c.
6a.
6b.
6c.
PLEASE NOTE: Ensure inboard surface gate sections come together before securing
and hardware.This is to eliminate nger hazards between adjacent ller bars.

ASSEMBLY / OPERATING INSTRUCTIONS
To install Safety Gate (continued)...
8
9
10
11
Hinge side mounting
Screws provided are for mounting directly into wood.
If mounting into brick,drywall or other surfaces,use
appropriate hardware.
If installing into hardwood (i.e. oak), drilling a pilot hole
may be necessary.
Cut out templates along all dotted lines,separating
template (A) from (B).
Hold template (A) vertically and completely
outstretched against mounting surface with the end
marked ”” even with the oor.
Mark screw hole positions.
Remove the template.
Use longer screws for mounting into studs behind
drywall.
Using 2 wood screws (K),mount upper hinge (G) (with
hole pointing up) in top 2 screw hole positions.
Using 2 wood screws (K),mount lower hinge bottom
(C) (with post pointing up) in bottom 2 screw hole
positions.
Locking Side Mounting
Screws provided are for mounting directly into wood.
If mounting into brick,drywall or other surfaces,use
appropriate hardware.
If installing into hardwood (i.e. oak), drilling a pilot hole
may be necessary.
Hold template (B) vertically and completely
outstretched against mounting surface with the end
marked ”” even with the oor.
Mark 4 screw hole positions.Remove the template.
8a.
8b.
8c.
8d.
8e.
8f.
8g.
8h.
9a.
9b.
10a.
11a.
11b.
11c.
11d.
11e.
11f.
ASSEMBLY / OPERATING INSTRUCTIONS
To install Safety Gate (continued)...
12 Determine which direction the gate should open.
For the top of stairways, gate should never open out
over stairs.
Insert stop pins (O) from behind in holes of locking
latch bracket (L) and lower latch bracket (M) opposite
desired opening direction.
12a.
12b.
12c.
13
14
15
16
Use longer screws for mounting into studs behind
drywall.
Using 2 wood screws (K) mount locking latch bracket
(L) in top 2 screw hole positions.
Using 2 wood screws (K) mount lower latch bracket
(M) in bottom 2 screw hole positions.
Centre gate in opening.Adjust upper hinge spindle
(H) so post ts into upper hinge hole (G).
Adjust lower hinge spindle (D) so end ts over lower
hinge post (C).
Space between end of gate and mounting surface
on hinge side may be no less than 31.75mm and not
more than 63.5mm.
13a.
13b.
14a.
15a.
16a.
16b.
IMPORTANT: The gate cannot open to the stop pinside.

ASSEMBLY / OPERATING INSTRUCTIONS
To install Safety Gate (continued)...
17
18
19
20
21
Adjust locking latch spindles (N) until they t securely
into both latch brackets.
Top spindle must click under locking latch when in the
closed position.
Space between end of gate and mounting surface
on locking side may be no less than 25mm and not
more than 70mm.
If adjusting the spindles does not achieve the correct
length,it may be necessary to lift gate off hinges and
readjust the sections (see step 3).
Check that gate can be smoothly opened and
closed.
Place spring (E) on lower hinge post.
Place lower hinge cap (F) on lower hinge and push
down until it clicks into locked position.
Using Phillips head screwdriver, tighten all screws and
screw sockets.
With wrench (P), securely tighten all 4 lock nuts toward
the gate.
17a.
17b.
17c.
18a.
18b.
19a.
20a.
21a.
21b.
ASSEMBLY / OPERATING INSTRUCTIONS
To install Safety Gate (continued)...
22
23
To open gate,press down on locking latch with thumb
and lift gate out of upper and lower brackets.
To lock gate,top locking latch spindle must click under
locking latch and bottom latch spindle must rest in
bottom bracket as shown in gure 17.
Temporary removal
The gate may be removed by pressing back on the
locking tab on top of lower hinge bottom while sliding
the hinge cap up.
Remove spring and lift gate off top and bottom hinges.
22a.
22b.
23a.
23b.
23c.
Hinge side Lock side
630mm - 1080mm
IMPORTANT: Ensure hinge cap cannot be pushed up and is locked in place.
PLEASE NOTE: gate should always be in the locked position.If gate is open and
excessive pressure is applied,(such as standing or swinging on the gate) structural
damage may occur.
PLEASE NOTE: For safety reasons,return spring and hinge cap onto hinge post,make
sure cap is locked in place.

HOW TO CARE FOR YOUR CHILDCARE SAFETY GATE
Cleaning
Maintenance
This product has been designed and developed with safety,comfort
and functionality in mind. Please take the time to read this manual
carefully before using this product and keep it in a safe place for
future reference. To ensure the long-lasting use of your gate, wipe
down with a damp cloth and use a mild soap solution if necessary.
Do not use abrasive cleaners. Always store product in a clean dry
place.
Always check parts regularly for tightness of screws, nuts and other
fasteners – tighten or replace if required.To maintain the safety of your
safety gate, seek prompt repairs for bent, torn, worn or broken parts.
Use only those parts and accessories approved by CNP Brands.
If you have any difculties in assembling the safety gate, please
contact our Service Department.
In Australia, contact CNP Brands on 1300 667 137, in New Zealand
contact Wainhouse Distribution on 0800 567 5000.
ABOUT US
About CNP Brands
Currently,CNP Brands boasts one of the most diverse brand portfolios
with a combination of company owned brands and distribution
agreements.These include distribution lines for 4moms,Brica,Cybex,
Eveno, Good Baby, Lascal, Maclaren, Motorola, Munchkin, OiOi &
Summer Infant.
Our own brands, including Childcare, have gone from strength to
strength in recent years. Childcare, and our premium brand bebe
care, demonstrate our commitment to quality and continuing
investment in product development.

Distributed in Australia by CNP Brands
20 Calarco Drive,
Derrimut,VIC, 3030
Customer Service 1300 667 137
W: www.cnpbrands.com.au
E: [e-mail]
F: www.facebook.com/CNPBrands
I: @cnp_baby
Distributed in New Zealand by Wainhouse
Distribution
2-6 Argyle St, Morningside,
PO Box 41-014,
St Lukes,Auckland, New Zealand
Customer Service: 0800 567 5000
E: [email protected].nz