Childcare 089420 User manual

01
DELUXE UNIVERSAL
HEARTH GATE
Model # 089420
IMPORTANT: RETAIN FOR FUTURE
REFERENCE, READ CAREFULLY

This product has been designed for use with children up to 24 months of age.
This product has been designed and manufactured to comply with the Safety Standard ASTM F1004.
When used as a safety gate, never use without wall ttings.
When used as a hearth gate, always place the gate minimum 75cm away from the source of heat / re and minimum 90cm from
open re.
Since every replace / wood burning stove reaches different temperatures, the above placing is only intended as a guideline. Test
your own unit at maximum heat output before placing the gate. If the gate is hot to touch, move gate further from heat source than
the recommended minimum distance.
Check and tighten mountings regularly.
Never allow child to climb or swing on gate.
Do not use if any part of gate is broken or missing.
When folded, store away from children.
This product will not necessarily prevent all accidents.
Never leave child unattended.
Use only approved spare parts and accessories from the manufacturer.
Use only with locking mechanism securely engaged.
Install according to the manufacturer’s instructions.
When used as a re surround, this product is not a re guard. It is intended to keep children away from the area surrounding the
replace.
Do not leave anything in the hearth gate which could provide a foothold or create a danger of suffocation or strangulation.
When used as a hearth gate be aware of the risk of open re and other sources of strong heat, such as electric bar res, gas res,
etc in the vicinity of the hearth gate.
Read all instructions before assembly and use of the gate. Keep
instructions for future use.
Safety Precautions
TO PREVENT SERIOUS INJURY OR DEATH, SECURELY
INSTALL GATE OR ENCLOSURE AND USE ACCORDING TO
MANUFACTURER’S INSTRUCTIONS.
NEVER LEAVE CHILD UNATTENDED.
NEVER USE WITH A CHILD ABLE TO CLIMB OVER OR DISLODGE/
OPEN THE GATE OR ENCLOSURE.
THIS PRODUCT WILL NOT NECESSARILY PREVENT ALL
ACCIDENTS.
USE ONLY WITH LOCKING/LATCHING MECHANISM SECURELY
ENGAGED.
WARNING
WARNING
DO NOT FORCE HINGES
Please read the instructions regarding adjusting the hinge position on page 5 or 9

03
Due to variations in the style and design of our products, the photographs and illustrations
shown in this instruction manual are generic, therefore product fabrics, colour and
design may vary from images shown. CNP Brands reserves the right to alter product
specications without notice as a result of our ongoing policy of product improvement.
Contents
Assembly contents list
Assembly / Operating instructions
How to care for your Childcare Gate
Congratulations on your purchase of the
Childcare Deluxe Universal Hearth Gate.
This product has been designed and developed with
safety, comfort and functionality in mind. Please take
the time to read this manual carefully before using
this product and keep it in a safe place for future
reference.

04
Supplied loose in box:
Assembly Contents
Check what you have received...
You have received 1 box. Please check the contents of the box against the list below. If anything is
missing, please contact Customer Service. In Australia, contact CNP Brands on 1300 667 137, in
New Zealand contact Wainhouse Distribution on 0800 567 5000.
x1
x2
x2
x2
x4
x7
x1
x1
x1
x1
x8
x2
x1
Hearth Gate
(6 sections)
Lower bracket
Lower bracket
slider
Upper bracket
Wall plates
Removable
vertical bar
(pre-assembled
in hearth gate)
Bottom hinge
caps with groove
(pre-assembled)
Bottom hinge
cap plain
(pre-assembled)
Hinge cones
(pre-assembled)
Top hinge cap
(rounded)
(pre-assembled)
Wood screws
Lower bracket
bolt and nut
Mattress

05
Assembly / Operating Instructions
Setting up as Play Den
1. Unpack the hearth gate on a stable surface making sure the
handle is on the top.
2. Unfold the sections by pushing in
the button on the join and turning
the sections. If required, lift the top
section slightly while pushing the
button.
3. Unfold the hearth gate into either a hexagon or square. The
markings on the top of the hinges indicate the position to unfold
each hinge for either hexagon or square conguration.
4. The removable vertical bar has been tted into the end section
by the manufacturers. Lift up the vertical bar and remove it by
sliding it out of the lower hinge.

06
Assembly / Operating Instructions
Setting up as Play Den (cont)
5. Remove the pre-assembled
hinge cone and top and
bottom hinge caps from the
ends of the den which are to
be joined together.
6. Connect the two sections by aligning the ends of the sections
and ensuring that the hinges drop together on both the top and
the bottom.
7. Push the vertical bar up into the
top hinge and then slide into the
groove in the bottom hinge. Ensure
the vertical bar is inserted with the
protruding rod at the top.

07
Assembly / Operating Instructions
To open the gate
Squeeze the handle tightly and slide
lock across at the same time. The gate
may then be opened in either direction.
To close the gate
Squeeze the handle tightly and slide the lock at the same time. Align
the gate and gate frame. Release the handle and the gate should lock
correctly. Please note that the gate will be properly secured when the
locking bar has also engaged in the bottom of the gate frame.
Positioning as Hearth Gate around a fireplace
1. When used as a hearth barrier around a replace, the distance between the replace /
hearth and gate sections must be a minimum of 75cm. The gate must never be setup in a
straight line. Should it not be possible to keep the recommended minimum distances, gate
extensions are available for purchase.
2. When used as a hearth barrier around an open re, the distance between the replace and
gate sections must be a minimum of 90cm. The gate must never be setup in a straight line.
WARNING: The minimum distances suggested between replace and gates are only
recommended distances sincce every replace / wood burning stove reaches different
temperatures. Test your unit at maximum heat output before nal placing of the gate.
Place the gate according to the instructions at maximum heat output. If the gate is too hot to
touch, move gate further from the heat source than recommended.

08
Assembly / Operating Instructions
Positioning the Hearth Gate at the bottom of stairs
If the gate is to be positioned at the bottom of stairs. please note the
following:
• The gate must be setup in a curve away from the stairs.
• The gate must be placed as far away from the stairs as possible
so that the child will not be able to reach the bottom stair and
climb over the gate.
• There must be a minimum distance of 40cm between gate and
stairs.
Should it not be possible to keep the recommended minimum
distances, gate extensions are available for purchase.
Positioning the Hearth Gate at the top of stairs
If the gate is to be positioned at the top of stairs. please note the
following:
• The gate must be setup in a curve away from the stairs.
• The gate must never be setup in a straight line.
• There must be a minimum distance of 40cm between gate and
stairs.
Should it not be possible to keep the recommended minimum
distances, gate extensions are available for purchase.
Positioning the Hearth Gate in general
Please note that the child is able to reach through the bars, therefore
ensure the gate is placed far enough away from other objects. The
gate must never be setup in a straight line.
PLEASE NOTE:
With 3 sections, the gate ts openings from 90-180cm
With 5 sections, the gate ts openings from 90-300cm
With 6 sections, the gate ts openings from 90-360cm

09
Assembly / Operating Instructions
Setting up as Hearth Gate and Configure Gate
1. Unpack the hearth gate on a stable surface making sure the
handle is on the top.
2. Unfold the sections by pushing in
the button on the join and turning
the sections. If required, lift the top
section slightly while pushing the
button.
3. Unfold the hearth gate into either a hexagon or square. The
markings on the top of the hinges indicate the position to unfold
each hinge for either hexagon or square conguration.
4. The removable vertical bar has been tted into the end section
by the manufacturers. Lift up the vertical bar and remove it by
sliding it out of the lower hinge.
5. Remove the hinge cone from the upper hinge and the hinge cap
from the lower rail.

10
Assembly / Operating Instructions
Setting up as Hearth Gate and Configure Gate
6. Connect the two sections by aligning the ends of the sections
and ensuring that the hinges drop together on both the top and
the bottom.
Fitting the mattress
1. Pass the elastic underneath three
of the hinges.
2. Remove the vertical removable bar,
and loop the elastic around the slot
in the hinge before replacing the
vertical bar.
3. Loop the remaining elastic
underneath and around the
remaining three hinges.
7. Push the vertical bar up into the
top hinge and then slide into the
groove in the bottom hinge. Ensure
the vertical bar is inserted with the
protruding rod at the top.