Childcare 095110 User manual

JUNIOR TABLE
AND CHAIR SET
Model # 095110
IMPORTANT:
RETAIN FOR FUTURE REFERENCE, READ CAREFULLY

Suitable for children from 18 months up to a maximum weight of 20kgs.
Ensure the table and chair set is completely assembled and check that all parts are securely
tightened before using the table and chair set.
Do not over tighten bolts.
Retain your sales receipt to provide proof of purchase.
Read all instructions before assembly and use of the junior table and
chair set. Keep instructions for future use.
Safety Precautions
THIS PRODUCT CONTAINS SMALL PARTS WHICH ARE FOR
ADULT ASSEMBLY ONLY.
AS SMALL PARTS ARE INVOLVED IN ASSEMBLY, CHILDREN
SHOULD BE KEPT CLEAR OF THE ASSEMBLY AREA.
IDENTIFY ALL PARTS AND COMPONENTS, CLEAR AN AREA
ON THE FLOOR FOR ASSEMBLY AND PLACE A SHEET ON
THE FLOOR TO ENSURE THE TABLE AND CHAIR SET WILL
NOT BE SCRATCHED DURING ASSEMBLY.
DISPOSE OF ALL PACKAGING MATERIAL IMMEDIATELY
AFTER THE TABLE AND CHAIR SET IS ASSEMBLED.
WARNING

3
Due to variations in the style and design of our products, the photographs and illustrations
shown in this instruction manual are generic, therefore product fabrics, colour and
design may vary from images shown. CNP Brands reserves the right to alter product
specications without notice as a result of our ongoing policy of product improvement.
Contents
Assembly contents list
Assembly / Operating instructions
How to care for your Junior Table and Chair Set
Congratulations on your purchase of the
Childcare Junior Table and Chair Set.
This product has been designed and developed with
safety, comfort and functionality in mind. Please take
the time to read this manual carefully before using
this product and keep it in a safe place for future
reference.

4
x2
pairs
x2
x4
x2
x2
x2
Assembly Contents
Check what you have received...
You have received 1 box. Please check the contents of the box against the list below. If
anything is missing, please contact Customer Service. In Australia, contact CNP Brands on
1300 667 137, in New Zealand contact Wainhouse Distribution on 0800 567 5000.
Chair side panels
Chair back panel
Chair centre panel
Chair seat support
Chair base cross panel
Chair seat panel

5
x2
x2
x2
x1
x16
x8
x40
Assembly Contents
Table side panel
Table front panel
Table support
Table base panel
Screw
Barrel nut & assembly bolt
Dowel

6
Assembly / Operating Instructions
Assembling chairs
1. Insert dowels into the outer holes on the ends of the chair back
panel.
2. Place the chair back panel into position as shown, at the top of
one of the side panels.
3. Secure with screw, using an allen key to fasten the screw
securely.
4. Insert dowels into the lower holes of the chair centre panels.
5. Place one centre panel into position at the middle rear of
the side panel. Please ensure the groove in the centre panel
matches with the groove in the side panel as shown.
6. Secure the centre panel with screw, using an allen key to fasten
the screw securely.

7
Assembly / Operating Instructions
Assembling chairs continued
7. Place second centre panel into position at the front of the side
panel. Please ensure the groove in the centre panels matches
with the groove in the side panel.
8. Secure the centre panel with screw, using an allen key to fasten
the screw securely.
9. Insert dowels into the base cross panel.
10. Place base cross panel into position on the lower bar of the side
panel.
11. Secure the cross panel with screw, using an allen key to fasten
the screw securely.
12. Insert dowels into the seat support, and place into position as
shown.
13. Slide the chair seat panel into position as shown.

8
Assembly / Operating Instructions
14. Place the opposite side panel into position, ensuring all dowels
are correctly tting into the holes on the side panel.
Assembling chairs continued
15. Secure the side panel with screws, using an allen key to fasten
the screws securely.

9
Assembly / Operating Instructions
Assembling table
1. Insert dowels into the centre holes of one of the table front
panels.
2. Place front panel into position in one corner of the side panel.
Please ensure the groove in the front panel matches with the
groove in the side panel as shown.
3. Insert two barrel nuts into the holes in the front panel. Please
ensure the slot in the barrel nut is aligned vertically.
4. Secure the front panel with assembly bolts, using an allen key to
fasten the bolts securely.
5. Place dowels into the holes on one of the table supports, and
place into position as shown.

10
Assembly / Operating Instructions
6. Repeat step 5 to place the other table support into position.
Assembling table continued
7. Slide the table base panel into position as shown.
8. Place the second table side panel into position, ensuring all
dowels are correctly tting into the holes on the side panel.
9. Secure the side panel with assembly bolts, using an allen key to
fasten the bolts securely.